SEARCH · Engineering Papers

Results for “Electrode structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS2017

Transparent Conductive Ink for Additive Manufacturing

NASA analyzes, tests, packages, and fabricates electrical, electronic, and electromechanical (EEE) parts. Nanotechnology is listed in NASA's Technology Roadmap as a key area to invest for further development.1 This research project focused on using nanotechnology to improve electroluminescent lighting in terms of additive manufacturing and to increase energy efficiency. Specifically, this project's goal was to produce a conductive but transparent printable ink that can be sprayed on any surface for use as one of the electrodes in electroluminescent device design. This innovative work is known as thick film dielectric electroluminescent (TDEL) technology. TDEL devices are used for "backlighting, illumination, and identification due to their tunable color output, scalability, and efficiency" (I.K. Small, T.D. Rolin, and A.D. Shields, "3D Printed Electroluminescent Light Panels," NASA Fiscal Year 2017 Center Innovation Fund Proposal, unpublished data, 2017). These devices use a 'front-to-back' printing method, where the substrate is the transparent layer, and the dielectric and phosphor are layered on top. This project is a first step in the process of creating a 3D printable 'back-to-front' electroluminescent device. Back-to-front 3D-printed devices are beneficial because they can be printed onto different substrates and embedded in different surfaces, and the substrate is not required to be transparent, all because the light is emitted from the top surface through the transparent conductor. Advances in this area will help further development of printing TDEL devices on an array of different surfaces. Figure 1 demonstrates the layering of the two electrodes that are aligned in a parallel plate capacitor structure (I.K. Small, T.D. Rolin, and A.D. Shields, "3D Printed Electroluminescent Light Panels," NASA Fiscal Year 2017 Center Innovation Fund Proposal, unpublished data, 2017). Voltage is applied across the device, and the subsequent electron excitation results in light emission at the top layer.

Patlan, X. J.↗

NASA NTRS1977

Electrode surface studies by LEED-Auger

The role the electronic and geometric structures of the metal surface play in electrochemical surface reactions remains as yet an unknown factor. In order to investigate these surface contributions to electrochemical reactions, a low-energy-electron diffraction (LEED) and an Auger electron spectrometer (AES) have been combined with an electrochemical thin-layer cell. The surface to be studied electrochemically is first characterized by LEED-AES and then transferred into a second chamber where it becomes part of the electrochemical thin-layer cell. Electrochemical reactions are then run on this surface. The sample may then be transferred back to the LEED-AES chamber for further characterization. Data on Pt (111) will be presented.

Ogrady, W. E.↗

NASA NTRS1988

Performance of lightweight nickel electrodes

The NASA Lewis Research Center is currently developing nickel electrodes for nickel-hydrogen (Ni-H2) batteries. These electrodes are lighter in weight and have higher energy densities than the heavier state-of-the-art (SOA) sintered nickel electrodes. In the present approach, lightweight materials or plaques are used as conductive supports for the nickel hydroxide active material. These plaques (fiber and felt, nickel plated plastic and graphite) are commercial products that are fabricated into nickel electrodes by electrochemically impregnating them with active material. Evaluation is performed in half cells structured in the bipolar configuration. Initial performance tests include capacity measurements at five discharge levels, C/2, 1.0C 1.37C, 2.0C and 2.74C. The electrodes that pass the initial tests are life cycle tested in a low Earth orbit regime at 80 percent depth of discharge. Different formulations of nickel fiber materials obtained from several manufacturers are currently being tested as possible candidates for nickel electrodes. One particular lightweight fiber mat electrode has accumulated over 3000 cycles to date, with stable capacity and voltage. Life and performance data of this electrode were investigated and presented. Good dimensional stability and active material adherence have been demonstrated in electrodes made from this lightweight plaque.

Britton, Doris L.↗

NASA NTRS1989

Lightweight fibrous nickel electrodes for nickel-hydrogen batteries

The NASA Lewis Research Center is currently developing nickel electrodes for nickel-hydrogen batteries. These electrodes are lighter in weight and have higher energy densities than the heavier state-of-the-art sintered nickel electrodes. Lightweight fibrous materials or plaques are used as conductive supports for the nickel hydroxide active material. These materials are commercial products that are fabricated into nickel electrodes by electrochemically impregnating them with active material. Evaluation is performed in half cells structured in the bipolar configuration. Initial performance tests include capacity measurements at five discharge levels, C/2, 1.0C, 1.37C, 2.0C, and 2.74C. The electrodes that pass the initial tests are life cycle-tested in a low Earth orbit regime at 80 percent depth of discharge.

Britton, Doris L.↗

NASA NTRS1988

Performance of lightweight nickel electrodes

The NASA Lewis Research Center is currently developing nickel electrodes for nickel-hydrogen (Ni-H2) batteries. These electrodes are lighter in weight and have higher energy densities than the heavier state-of-the-art (SOA) sintered nickel electrodes. In the present approach, lightweight materials or plaques are used as conductive supports for the nickel hydroxide active material. These plaques (fiber and felt, nickel plated plastic and graphite) are commercial products that are fabricated into nickel electrodes by electrochemically impregnating them with active material. Evaluation is performed in half cells structured in the bipolar configuration. Initial performance tests include capacity measurements at five discharge levels, C/2, 1.0C, 1.37C, 2.0C and 2.74C. The electrodes that pass the initial tests are life cycle tested in a low earth orbit regime at 80 percent depth of discharge. Different formulations of nickel fiber materials obtained from several manufacturers are currently being tested as possible candidates for nickel electrodes. One particular lightweight fiber mat electrode has accumulated over 3000 cycles to date, with stable capacity and voltage. Life and performance data of this electrode were investigated and presented. Good dimensional stability and active material adherence have been demonstrated in electrodes made from this lightweight plaque.

Britton, Doris L.↗

NASA NTRS1994

Making Fuel-Cell Electrodes By Electrodeposition

Electrodes for direct oxidation of methanol in fuel cells fabricated in process involving room-temperature electro-chemical deposition of platinum-alloy catalysts on commercially available high-surface-area carbon support structures containing polytetrafluoroethylene (PTFE). Process takes 30 to 50 minutes and results in electrodes catalytically active as prepared; no need for additional activation step. Composition of catalytic platinum alloy and sizes of particles in catalytic layers on electrodes varied by changing operating conditions during electrodeposition; process affords additional flexibility in design of electrocatalysts.

Narayanan, Sekharipuram R.↗

NASA NTRS1994

Improved Micromachined Transducers

Sensor systems of proposed type incorporate micromachined silicon-based structures as electrostatic force and displacement actuators and micromachined quantum-mechanical-tunneling electrodes as one form of displacement transducers, along with electronic circuits providing multiple electrical stimuli to displacement electrodes for measurement, calibration, monitoring of sensor status, and adjustment. Concept applicable to accelerometers, seismometers, geophones, magnetometers, pressure gauges, and other sensors in which phenomena of interest measured in terms of forces on, and/or displacements of, structural components. Provides completely remote measurement, control, health monitoring, treatment, and like, using telemetry commands.

Hartley, Frank T.↗

NASA NTRS2005

Bifunctional catalytic electrode

The present invention relates to an oxygen electrode for a unitized regenerative hydrogen-oxygen fuel cell and the unitized regenerative fuel cell having the oxygen electrode. The oxygen electrode contains components electrocatalytically active for the evolution of oxygen from water and the reduction of oxygen to water, and has a structure that supports the flow of both water and gases between the catalytically active surface and a flow field or electrode chamber for bulk flow of the fluids. The electrode has an electrocatalyst layer and a diffusion backing layer interspersed with hydrophilic and hydrophobic regions. The diffusion backing layer consists of a metal core having gas diffusion structures bonded to the metal core.

Cisar, Alan↗

NASA NTRS1988

Effects of Na2MoO4 and Na2WO4 on molybdenum and tungsten electrodes for the alkali metal thermoelectric converter (AMTEC)

The effects of adding Na2MoO4 and Na2WO4 to porous Mo and W electrodes, respectively, on the performance and impedance characteristics of the electrodes in an alkali metal thermoelectric converter (AMTEC) were investigated. It was found that corrosion of the porous electrode by Na2MoO4 or Na2WO4 to form Na2MO3O6 and WO2, respectively, and recrystallization of the Mo or W as the salt evaporates, result in major morphological changes including a loss of columnar structure and a significant increase in porosity. This effect is more pronounced in Na2MoO4/Mo electrodes, due to the lower stability of Na2MoO4.

Williams, R. M.↗

NASA NTRS2006

Air-bridge and Vertical CNT Switches for High Performance Switching Applications

Carbon nanotubes are attractive for switching applications since electrostatically-actuated CNT switches have low actuation voltages and power requirements, while allowing GHz switching speeds that stem from the inherently high elastic modulus and low mass of the CNT.Our first NEM structure, the air-bridge switch, consists of suspended single-walled nanotubes (SWNTs) that lie above a sputtered Nb base electrode, where contact to the CNTs is made using evaporated Au/Ti. Electrical measurements of these air-bridge devices show well-defined ON and OFF states as a dc bias of a few volts is applied between the CNT and the Nb-base electrode. The CNT air-bridge switches were measured to have switching times down to a few nanoseconds. Our second NEM structure, the vertical CNT switch, consists of nanotubes grown perpendicular to the substrate. Vertical multi-walled nanotubes (MWNTs) are grown directly on a heavily doped Si substrate, from 200 - 300 nm wide, approximately 1 micrometer deep nano-pockets, with Nb metal electrodes to result in the formation of a vertical single-pole-double-throw switch architecture.

nanoelectromechanical systems (NEMS) devices↗

NASA NTRS1991

Micromachined silicon tunnel sensor for motion detection

The extreme sensitivity of electron tunneling to variations in electrode separation has been used to construct a novel, compact displacement transducer. Electrostatic forces are used to control the separation between the tunneling electrodes, thereby eliminating the need for piezoelectric actuators. The entire structure is composed of micromachined silicon single crystals, including a folded cantilever spring and a tip. Measurements of displacement sensitivity and noise are reported. This device offers a substantial improvement over conventional technology for applications which require compact, highly sensitive transducers.

Kenny, T. W.↗

NASA NTRS1992

Electron tunnel sensors

We have used the extreme sensitivity of electron tunneling to variations in electrode separation to construct a novel, compact displacement transducer. Electrostatic forces are used to control the separation between the tunneling electrodes, thereby eliminating the need for piezoelectric actuators. The entire structure is composed of micromachined silicon single crystals. Applications of the tunneling displacement transducer to the measurement of acceleration and infrared signals are discussed. Measurements of acceleration and infrared sensitivity are reported.

Kenny, T. W.↗

NASA NTRS2003

New Method Developed To Purify Single Wall Carbon Nanotubes for Aerospace Applications

Single wall carbon nanotubes have attracted considerable attention because of their remarkable mechanical properties and electrical and thermal conductivities. Use of these materials as primary or secondary reinforcements in polymers or ceramics could lead to new materials with significantly enhanced mechanical strength and electrical and thermal conductivity. Use of carbon-nanotube-reinforced materials in aerospace components will enable substantial reductions in component weight and improvements in durability and safety. Potential applications for single wall carbon nanotubes include lightweight components for vehicle structures and propulsion systems, fuel cell components (bipolar plates and electrodes) and battery electrodes, and ultra-lightweight materials for use in solar sails. A major barrier to the successful use of carbon nanotubes in these components is the need for methods to economically produce pure carbon nanotubes in large enough quantities to not only evaluate their suitability for certain applications but also produce actual components. Most carbon nanotube synthesis methods, including the HiPCO (high pressure carbon monoxide) method developed by Smalley and others, employ metal catalysts that remain trapped in the final product. These catalyst impurities can affect nanotube properties and accelerate their decomposition. The development of techniques to remove most, if not all, of these impurities is essential to their successful use in practical applications. A new method has been developed at the NASA Glenn Research Center to purify gram-scale quantities of single wall carbon nanotubes. This method, a modification of a gas phase purification technique previously reported by Smalley and others, uses a combination of high-temperature oxidations and repeated extractions with nitric and hydrochloric acid. This improved procedure significantly reduces the amount of impurities (catalyst and nonnanotube forms of carbon) within the nanotubes, increasing their stability significantly. The onset of decomposition of the purified nanotubes (determined by thermal gravimetric analysis in air) is more than 300 C higher than that of the crude nanotubes. Transmission electron microscopy analysis of nanotubes purified by this method reveals near complete removal of iron catalyst particles. Analysis of the nanotubes using inductively coupled plasma spectroscopy revealed that the iron content of the nanotubes was reduced from 22.7 wt% in the crude nanotubes to less than 0.02 wt%. X-ray photoelectron spectroscopy revealed a decrease in iron content after purification as well as an increase in oxygen content due to the formation of carboxylic acid groups on the surface of the nanotubes. Nanotubes purified by this improved method can be readily dispersed in common organic solvents, in particular N,N-dimethylformamide, using prolonged ultrasonic treatment. These dispersions can then be used to incorporate single wall carbon nanotubes into polymer films.

Lebron, Marisabel↗

NASA NTRS2011

Chalcogenide Nanoionic-Based Radio Frequency Switch

A nonvolatile nanoionic switch is disclosed. A thin layer of chalcogenide glass engages a substrate and a metal selected from the group of silver and copper photo-dissolved in the chalcogenide glass. A first oxidizable electrode and a second inert electrode engage the chalcogenide glass and are spaced apart from each other forming a gap there between. A direct current voltage source is applied with positive polarity applied to the oxidizable electrode and negative polarity applied to the inert electrode which electrodeposits silver or copper across the gap closing the switch. Reversing the polarity of the switch dissolves the electrodeposited metal and returns it to the oxidizable electrode. A capacitor arrangement may be formed with the same structure and process.

Nessel, James↗

NASA NTRS2013

Chalcogenide Nanoionic-based Radio Frequency Switch

A nonvolatile nanoionic switch is disclosed. A thin layer of chalcogenide glass engages a substrate and a metal selected from the group of silver and copper photo-dissolved in the chalcogenide glass. A first oxidizable electrode and a second inert electrode engage the chalcogenide glass and are spaced apart from each other forming a gap therebetween. A direct current voltage source is applied with positive polarity applied to the oxidizable electrode and negative polarity applied to the inert electrode which electrodeposits silver or copper across the gap closing the switch. Reversing the polarity of the switch dissolves the electrodeposited metal and returns it to the oxidizable electrode. A capacitor arrangement may be formed with the same structure and process.

Nessel, James↗

NASA NTRS2009

Multilayer Ferritin Array for Bionanobattery

A thin-film electrode for a bio-nanobattery is produced by consecutively depositing arrays of a ferritin protein on a substrate, employing a spin self-assembly procedure. By this procedure, a first ferritin layer is first formed on the substrate, followed by building a second, oppositely-charged ferritin layer on the top of the first ferritin layer to form a bilayer structure. Oppositely-charged ferritin layers are subsequently deposited on top of each other until a desired number of bilayer structures is produced. An ordered, uniform, stable and robust, thin-film electrode material of enhanced packing density is presented, which provides optimal charge density for the bio-nanobattery.

Chu, Sang-Hyon↗

NASA NTRS1965

Wire bundle formed into grids with minute interstices

Deforming the ends of a bundle of closely packed parallel wires to restrict the interstices to substantially uniform and minute dimensions produces grids or filters for ion engines. Porous metal structures made by this process are also used as fuel cell electrodes, diffusion membranes, and catalysts.

Todd, H. H.↗

NASA NTRS2003

Modeling of Carbon Nanotube Schottky Barrier Reduction for Holes in Air

A model is proposed for the recently observed lower Schottky barrier for holes in air than in vacuum at a metallic electrode - semiconducting carbon nanotube (CNT) junction. In air, the CNT is oxidized. The oxygen molecules on the CNT surface will attract negative charges and will be negatively charged. The negative charges on the solid surface generally enhance the surface dipole and provide stronger electron confinement within the solid. Thus the CNT work function will increase in air. Then the Schottky barrier for holes will have to increase in air according to the standard band-alignment theory, but this is against the experiment. In order to overcome this difficulty, we propose a new Schottky barrier model, assuming that there is a transition region between the electrode and the CNT, where an appreciable potential can drop. We assume that electrodes are placed at the side of the CNT and the contact is formed via the van der Waals interaction. Since the electrode surface is not atomically flat in practical situations, the contact will not be intimate and there will be a transition region before the usual metallic bulk structure starts. In this view, the Schottky barrier is determined not only by the work function difference of the electrodes and the CNT, but also by the potential drop in the transition region. The oxidation increases the potential drop and leads to a lower Schottky barrier for holes. This relation will be demonstrated in a graphical manner by expressing the potential drop as a function of CNT band bending. The potential drop is comparable to the CNT band gap when, e.g., the transition region is about a few Angstroms thick, the oxygen molecule coverage is about 10 %, and an oxygen molecule is charged by about 0.01-0.1 of the unit charge (1-10 % of molecules are charged). The proposed mechanism prevails for both p - and n-CNTs. The model consistently explains the CNT oxidation experiments reported so far.

Yamada, Toshishige↗