Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Crystal engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Test Results for the SEA Ice Crystal Detector (ICD) under SLD Conditions at the NASA IRT

The Science Engineering Associates hot-wire Ice Crystal Detector was tested under Appendix C and Supercooled Large Drop Conditions at the NASA Icing Research Tunnel, with the purpose of comparing the measurements to the tunnel LWC calibration, and to test the performance of the mixed-phase retrievals of the probe. The liquid water content measured by the total water content sensor of the probe agreed well with the tunnel calibration over a wide range of MVDs, not unexpectedly since the tunnel was calibrated with a similar Multiwire hot-wire probe. A scale factor difference of about 7% was attributed to the lack of an efficiency correction for the Ice Crystal Detector at smaller median volume diameters, and typical sample area uncertainties of liquid water content devices. In addition, the simultaneous equations that are used to retrieve liquid and ice water contents were tested under liquid and glaciated conditions. Using constant ice and water efficiencies for each wire, the equations were found to produce a large and false ice water content retrieval in large median volume diameter liquid cases. By applying a liquid efficiency to the liquid water content sensor that varied with median volume diameter, retrievals were improved such that false ice water content was less than ±10% of the total water content out to the 460 μm median volume diameter limit of the testing. The probe was also tested in glaciated conditions by freezing out a small median volume diameter spray. Using constant ice efficiencies for the two sensors provided from aircraft measurements, the retrieved ice water content was about 40% higher than expected for the case presented, likely due to the ice efficiencies that were used from aircraft measurements of natural clouds being too low for the tunnel’s glaciated sprays. Application of ice efficiencies that vary with particle size and potentially other parameters will be explored for future improvement of retrievals.

o Aircraft Icing↗
DOE OSTI2021

Influence of side-chain isomerization on the isothermal crystallization kinetics of poly(3-alkylthiophenes)

Flexible alkyl side chain in conjugate polymers (CPs) improves the solubility and promotes solution processability, in addition, it affects interchain packing and charge mobilities. Despite the well-known charge mobility and morphology correlation for these semi-crystalline polymers, there is a lack of fundamental understanding of the impact of side chain on their crystallization kinetics. In the present work, isothermal crystallization of five poly(3-alkylthiophene-2,5-diyl) (P3ATs) with different side-chain structures were systematically investigated. To suppress the extremely fast crystallization and trap the sample into amorphous glass, an advanced fast scanning chip calorimetry technique, which is able to quench the sample with few to tens thousands of K/s, was applied. Results show that the crystallization of P3ATs was greatly inhibited after incorporation of branched side chains, as indicated by a dramatic up to six orders of magnitude decrease in the crystallization rate. The suppressed crystallization of P3ATs were correlated with an increased π–π stacking distance due to unfavorable side-chain steric interaction. This research provides a pathway to use side-chain engineering to control the crystallization behavior for CPs, thus to control device performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Binary and Ternary Colloidal Cu–Sn–Te Nanocrystals for Thermoelectric Thin Films

Recent advances in copper chalcogenide-based nanocrystals (NCs), copper sulfide, and copper selenide derived nanostructures, have drawn considerable attention. However, reports of crystal phase and shape engineering of binary or ternary copper telluride NCs remain rare. Here, a colloidal hot-injection approach for producing binary copper/tin telluride, and ternary copper tin telluride NCs with controllable compositions, crystal structures, and morphologies is reported. Here, the crystal phase and growth behavior of these tellurides are systematically studied from both experimental and theoretical perspectives.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Engineering lithium-ion battery cathodes for high-voltage applications using electromagnetic excitation

Microwave radiation (MWR), a type of electromagnetic excitation source, reduces the synthesis temperature and processing time for chemical reactions compared to traditional synthesis methods. Recently, we demonstrated that MWR can engineer ceramics with different crystal phases compared to traditional methods [ Journal of Materials Chemistry A 5 , 35 (2017)]. Here, we further apply the MWR-assisted technique to improve the electrochemical performance of LiCoO 2 cathodes by engineering TiO 2 and ZrO 2 ceramic coatings. Electrochemical tests suggest that the TiO 2 coating improves the rate capability of the LiCoO 2 electrode. Both TiO 2 and ZrO 2 coatings improve the high-voltage (4.5 V) cycling stability of LiCoO 2 . The capacity remaining is improved from 52.8 to 84.4% and 81.9% by the TiO 2 coating and the ZrO 2 coating, respectively, after 40 cycles. We compare these results with existing studies that apply traditional methods to engineer TiO 2 /ZrO 2 on LiCoO 2 , and find that the MWR-assisted method shows better performance improvement. X-ray photoelectron spectroscopy measurements suggest that the improved cycling stability arises from the formation of metal fluorides that protect the electrode from side reactions with electrolytes. This mechanism is further supported by the reduced Co dissolution from TiO 2 /ZrO 2 -coated LiCoO 2 electrode after cycling. This study provides a new toolbox facilitating the integration of many delicate, low melting point materials like polymers into battery electrodes.

25 ENERGY STORAGE↗
DOE OSTI2023

Ordering of room-temperature magnetic skyrmions in a polar van der Waals magnet

Abstract Control and understanding of ensembles of skyrmions is important for realization of future technologies. In particular, the order-disorder transition associated with the 2D lattice of magnetic skyrmions can have significant implications for transport and other dynamic functionalities. To date, skyrmion ensembles have been primarily studied in bulk crystals, or as isolated skyrmions in thin film devices. Here, we investigate the condensation of the skyrmion phase at room temperature and zero field in a polar, van der Waals magnet. We demonstrate that we can engineer an ordered skyrmion crystal through structural confinement on the μ m scale, showing control over this order-disorder transition on scales relevant for device applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural and Optical Response of Polymer-Stabilized Blue Phase Liquid Crystal Films to Volatile Organic Compounds

Engineering useful mechanical properties into stimuli-responsive soft materials without compromising their responsiveness is, in many cases, an unresolved challenge. For example, polymer networks formed within blue-phase liquid crystals (BPs) have been shown to form mechanically robust films, but the impact of polymer networks on the response of these soft materials to chemical stimuli has not been explored. In this work, we report on the response of polymer-stabilized BPs (PSBPs) to volatile organic compounds (VOCs, using toluene as a model compound) and compare the response to BPs without polymer stabilization and to polymerized nematic and cholesteric phases. We find that PSBPs generate an optical response to toluene vapor (change in reflection intensity under crossed polars) that is sixfold greater in sensitivity than the polymerized nematic or cholesteric phases and with a limit of detection (140 ± 10 ppm at 25 °C) that is relevant to the measurement of permissible exposure limits for humans. Additionally, when compared to BPs that have not been polymerized, PSBPs respond to a broader range of toluene vapor concentrations (5000 vs <1000 ppm) over a wider temperature interval (25–45 vs 45–53 °C). We place these experimental observations into the context of a simple thermodynamic model to explore how the PSBP response reflects the effect of toluene on competing contributions of double-twisted LC cylinders, disclinations, and polymer network to the free energy that controls the PSBP lattice spacing. Overall, we conclude that the mechanical and thermal stability of PSBPs, when combined with their optical responsiveness to toluene, make this class of self-supporting LCs a promising one as the basis of passive and compact (e.g., wearable) sensors for VOCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

CrysFieldExplorer : rapid optimization of the crystal field Hamiltonian

A new approach to the fast optimization of crystal electric field (CEF) parameters to fit experimental data is presented. This approach is implemented in a lightweight Python-based program, CrysFieldExplorer. The main novelty of the method is the development of a unique loss function, referred to as the spectrum characteristic loss (L Spectrum ), which is based on the characteristic polynomial of the Hamiltonian matrix. Particle swarm optimization and a covariance matrix adaptation evolution strategy are used to find the minimum of the total loss function. It is demonstrated that CrysFieldExplorer can perform direct fitting of CEF parameters to any experimental data such as a neutron spectrum, susceptibility or magnetization measurements etc. CrysFieldExplorer can handle a large number of non-zero CEF parameters and reveal multiple local and global minimum solutions. Crystal field theory, the loss function, and the implementation and limitations of the program are discussed within the context of two examples.

42 ENGINEERING↗
DOE OSTI2024

Direct Air Capture of CO 2 via Reactive Crystallization

Atmospheric CO 2 removal using engineered chemical processes, aka direct air capture (DAC), has become an essential component of our available portfolio for mitigating climate change. Here we describe a promising approach to DAC based on reactive crystallization of atmospheric CO 2 (RC-DAC) with aqueous guanidine and amino acid. Compared to the previously studied phase-changing DAC processes involving initial CO 2 absorption by an aqueous alkaline solvent followed by carbonate crystallization in a second step, RC-DAC combines the CO 2 absorption and carbonate crystallization into a single step. Thus, as the insoluble carbonate salts are removed from solution by crystallization, more CO 2 is pulled from the air into solution, further driving the DAC process. The RC-DAC was performed in a household humidifier as the air–liquid contactor, which can handle solid–liquid slurries effectively. The crystallization was monitored in situ by pH measurements, real-time imaging with a microscope probe, and by Raman spectroscopy, and ex situ by NMR spectroscopy, powder X-ray diffraction, and total inorganic carbonate analysis. Further, the investigation provided a detailed mechanistic picture of the RC-DAC process, involving formation of carbamate and carbonate anions in solution, followed by sequential crystallization of different guanidinium carbonate phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2020

COMDES-MELT: A Turbofan Engine Icing Risk Analysis Tool, User’s Manual

The computational tool COMDES-MELT was developed to predict the susceptibility of turbofan engines to ice accretion when flying in an ice crystal environment. COMDES-MELT is a first-generation computational tool that can estimate the conditions at which the accretion of ice can occur, location within the turbofan engine compression system, and at which engine operating points within the flight trajectory. This is accomplished by tracking the parameters of static wet bulb temperature, ice particle melt ratio, and the ice-water to airflow rates ratio as ice crystals are ingested into the engine compression system. It has been used successfully to predict engine operating points for simulation in an altitude wind tunnel with ice crystal ingestion. These engine tests occur in a simulated ice crystal cloud environment. This predictive analysis has been used to generate the test matrix in preparation for tests in the Propulsion Systems Laboratory, an altitude test facility at the NASA Glenn Research Center. Furthermore, due to the speed of the code during an engine icing test, adjustments to the test matrix can be provided to the test engineer in real time to focus on a particular area of ice accretion susceptibility. The use of the COMDES-MELT code will be examined in this manual.

Turbofan engine↗
DOE OSTI2022

Discrete dislocation dynamics for crystal RVEs. Part 1: Periodic network kinematics

A novel implementation of the dislocation flux boundary condition in discrete dislocation dynamics is presented. The continuity of the individual dislocation loops in a periodic representative crystal volume (RVE) is enforced across the boundary of the RVE with the help of a dual topological description for representing dislocation line kinematics in two equivalent spaces representing the deforming crystal, the RVE and the unbounded crystal spaces. The former describes the motion of the dislocations in the simulated crystal RVE whereas the latter represents the motion of dislocations in an infinite space containing all replicas of the RVE. A mapping between the two spaces forms the basis of the implementation of flux boundary condition. The implementation details are discussed in the context of statistical homogeneity of bulk crystals undergoing macroscopically homogeneous plastic deformation. In this case, the boundary nodes associated with dislocation segments bear no relevance in the motion of the dislocations. Finally, some test cases are presented and discussed to establish the proposed approach.

42 ENGINEERING↗
DOE OSTI2020

2D Electrets of Ultrathin MoO 2 with Apparent Piezoelectricity

Since graphene, a variety of 2D materials have been fabricated in a quest for a tantalizing combination of properties and desired physiochemical behavior. 2D materials that are piezoelectric, i.e., that allow for a facile conversion of electrical energy into mechanical and vice versa, offer applications for sensors, actuators, energy harvesting, stretchable and flexible electronics, and energy storage, among others. Unfortunately, materials must satisfy stringent symmetry requirements to be classified as piezoelectric. Here, 2D ultrathin single-crystal molybdenum oxide (MoO 2 ) flakes that exhibit unexpected piezoelectric-like response are fabricated, as MoO 2 is centrosymmetric and should not exhibit intrinsic piezoelectricity. However, it is demonstrated that the apparent piezoelectricity in 2D MoO 2 emerges from an electret-like behavior induced by the trapping and stabilization of charges around defects in the material. Arguably, the material represents the first 2D electret material and suggests a route to artificially engineer piezoelectricity in 2D crystals. Specifically, it is found that the maximum out-of-plane piezoresponse is 0.56 pm V -1 , which is as strong as that observed in conventional 2D piezoelectric materials. The charges are found to be highly stable at room temperature with a trapping energy barrier of ≈2 eV.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Numerical characterization of quasi-steady thermal load for thin crystal at cryogenic temperature with nondiffusive heat transfer

With dramatically improved brightness and repetition rate, the thermal load for crystal optics in x-ray free-electron laser applications has also significantly increased. To mitigate the thermal load, one effective method is cryogenic cooling. However, the emerging nondiffusive heat transfer phenomenon at cryogenic temperature may cause design failure if overlooked. To evaluate the optical performance of thin crystal optics under thermal load at cryogenic temperature, an integrated numerical tool is presented and applied to characterize the thermal load on thin crystals with nondiffusive phenomena accounted. Significant thermally induced distortion of the rocking curve is observed from numerical simulation, leading to potential seed power reduction in hard x-ray self-seeding application. Cryogenic cooling is confirmed necessary by simulation to handle the thermal load at high repetition rate operation.

42 ENGINEERING↗
DOE OSTI2022

An Eulerian crystal plasticity framework for modeling large anisotropic deformations in energetic materials under shocks

Here, this paper demonstrates a novel Eulerian computational framework for modeling anisotropic elastoplastic deformations of organic crystalline energetic materials (EM) under shocks. While Eulerian formulations are advantageous for handling large deformations, constitutive laws in such formulations have been limited to isotropic elastoplastic models, which may not fully capture the shock response of crystalline EM. The present Eulerian framework for high-strain rates, large deformation material dynamics of EM incorporates anisotropic isochoric elasticity via a hypo-elastic constitutive law and visco-plastic single-crystal models. The calculations are validated against atomistic calculations and experimental data and benchmarked against Lagrangian (finite element) crystal plasticity computations for shock-propagation in a monoclinic organic crystal, octahydro-1,3,5,7-tetranitro-1,3,5,7 tetrazocine (β-HMX). The Cauchy stress components and the resolved shear stresses calculated using the present Eulerian approach are shown to be in good agreement with the Lagrangian computations for different crystal orientations. The Eulerian framework is then used for computations of shock-induced inert void collapse in β-HMX to study the effects of crystal orientations on hotspot formation under different loading intensities. The computations show that the hotspot temperature distributions and the collapse profiles are sensitive to the crystal orientations at lower impact velocities (viz., 500 m/s); when the impact velocity is increased to 1000 m/s, the collapse is predominantly hydrodynamic and the role of anisotropy is modest. The present methodology will be useful to simulate energy localization in shocked porous energetic material microstructures and other situations where large deformations of single and polycrystals govern the thermomechanical response.

42 ENGINEERING↗
NASA NTRS2016

Update on the NASA Glenn Propulsion Systems Lab Ice Crystal Cloud Characterization (2015)

NASA Glenn's Propulsion Systems Lab (PSL), an altitude engine test facility, was outfitted with a spray system to generate ice crystals. The first ice crystal characterization test occurred in 2012. At PSL, turbine engines and driven rigs can experience ice crystal icing at flight altitudes, temperatures and Mach numbers. To support these tests, four ice crystal characterizations have been conducted in two different facility configurations. In addition, super-cooled liquid and mixed phase clouds have also been generated. This paper will discuss the recent learning from the previous two calibrations. It will describe some of the 12-parameter calibration space, and how those parameters interact with each other, the instrumentation used to characterize the cloud and present a sample of the cloud characterization results.

Ice Clouds↗
NASA NTRS1999

Fatigue Failure Criteria for Single Crystal Nickel Superalloys

High Cycle Fatigue (HCF) induced failures in aircraft gas-turbine and rocket engine turbopump blades is a pervasive problem. Single crystal turbine blades are being utilized in rocket engine turbopumps and jet engines throughout industry and NASA because of their superior creep, stress rupture, melt resistance and thermomechanical fatigue capabilities over polycrystalline alloys. Single-crystal materials have highly orthotropic properties making the position of the crystal lattice relative to the pan geometry a significant factor in the overall analysis. The failure modes of single crystal turbine blades is complicated to predict due to the material orthotropy and variations in crystal orientations. A fatigue failure criteria based on the maximum shear stress amplitude [delta t max] on the 30 slip systems, is presented for single crystal nickel superalloys (FCC crystal). This criteria reduces the scatter in uniaxial LCF test data, for four different specimen orientations, for PWA 1484 at 1200 F in air, quite well. A power law curve fit of the failure parameter, delta t max, vs. cycles to failure is presented.

Arakere, Nagaraj K.↗
DOE OSTI2021

Spatiotemporal control of liquid crystal structure and dynamics through activity patterning

Active materials are capable of converting free energy into mechanical work to produce autonomous motion, and exhibit striking collective dynamics that biology relies on for essential functions. Controlling those dynamics and transport in synthetic systems has been particularly challenging. Here, we introduce the concept of spatially structured activity as a means of controlling and manipulating transport in active nematic liquid crystals consisting of actin filaments and light-sensitive myosin motors. In this work, simulations and experiments are used to demonstrate that topological defects can be generated at will and then constrained to move along specified trajectories by inducing local stresses in an otherwise passive material. These results provide a foundation for the design of autonomous and reconfigurable microfluidic systems where transport is controlled by modulating activity with light.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Use of wire grid polarizers with liquid crystal display for large-volume stereolithography

Spatial light modulators that use liquid crystal devices (LCDs) to pattern ultraviolet light for vat polymerization suffer from a few limitations: limited range of wavelengths that can be patterned, low damage threshold for incoming light, and low efficiency of light transmission. A monochrome LCD can more efficiently transmit useful wavelengths of light for stereolithography (365–405 nm) than a color LCD, but it still contains two absorptive film polarizers that suffer from the aforementioned limitations. Wire grid polarizers reflect rather than absorb the blocked polarizations of light, resulting in a higher intensity damage threshold. They can also polarize lower wavelength light that is limited only by the wire pitch. In this work, this research investigates the effects of replacing an LCD’s film polarizers with wire grid polarizers to enable polarization and patterning of high intensity UV light, resulting in shorter curing times and the ability to print a wider range of stereolithography feedstocks.

42 ENGINEERING↗
NASA NTRS2015

Ice Particle Impacts on a Flat Plate

An experimental study was conducted at the Ballistic Laboratory of NASA Glenn Research Center to study the impact of ice particles on a stationary flat surface target set at 45 degrees with respect to the direction of motion of the impinging particle (Figure 1). The experiment is part of NASA efforts to study the physics involved in engine power-loss events due to ice-crystal ingestion and ice accretion formation inside engines. These events can occur when aircraft encounter high-altitude convective weather.

ice particle↗