Modeling surface tension in compressible flow on an adaptively refined mesh
Not Available
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
The second-order factorizable discretization of the compressible Euler equations developed by Sidilkover is extended to conservation form on general curvilinear body-fitted grids. The discrete equations are solved by symmetric collective Gauss-Seidel relaxation and FAS multigrid. Solutions for flow in a channel with Mach numbers ranging from 0.0001 to a supercritical Mach number are shown, demonstrating uniform convergence rates and no loss of accuracy in the incompressible limit. A solution for the flow around the leading edge of a semi-infinite parabolic body demonstrates that the scheme maintains rapid convergence for a flow containing a stagnation point.
An existing computer program, the Axisymmetric Diffuser Duct Code (ADD code), which calculates compressible turbulent swirling flow through axisymmetric ducts was modified to permit calculation of flows through small gas turbine ducts with struts, guide vanes and large degrees of turning. The improvements include a coordinate generator, an end-wall loss model, and a generalized geometry capability to describe struts and guide vanes in ducts which turn more than 90 degrees. An improved output format was developed to provide the solution on any arbitrary plane in the duct and an extensive literature survey of calculation procedures used in gas turbine technology was completed which suggests improvements in the computer code. Calculations are presented for the flow through the AGT101 small gas turbine inlet duct and turbine exhaust diffuser which demonstrate the ADD code modifications implemented in the investigation. The computed results compare favorably with experimental results.
A Comment on the Letter by Y. Taroyan, [Phys Rev. Lett. 101, 245001 (2008)]. The authors of the Letter offer a Reply.
Constant-velocity elevated temperature compression tests have been conducted on a series of binary CoAl intermetallics produced by hot extrusion of blended prealloyed powders. The as-extruded materials were polycrystalline, and they retained their nominal 10-micron grain size after being tested between 1100 and 1400 K at strain rates ranging from 2 x 10 to the -4th to 2 x 10 to the -7th per sec. Significant plastic flow was obtained in all cases; while cracking was observed, much of this could be due to failure at matrix-oxide interfaces along extrusion stringers rather than to solely intergranular fracture. A maximum in flow strength occurs at an aluminum-to-cobalt ratio of 0.975, and the stress exponent appears to be constant for aluminum-to-cobalt ratios of 0.85 or more. It is likely that very aluminum-deficient materials deform by a different mechanism than do other compositions.
The present numerical method for the solution of the isenthalpic form of the governing equations for compressible viscous and inviscid flows has its basis in the concept of flux vector splitting in its implicit form, and has been tested in the cases of several difficult viscous and inviscid configurations. An acceleration of time-marching to steady state is accomplished by implementing a multigrid procedure which effectively increases the convergence rate. The steady state results obtained are largely of good quality, and required only short computational times.
Contains results on simulations of a Mach 2 expansion compression ramp which mirrors work done in the Tri Sonic Wind tunnel.
Significant progress has been made during the last five years to adapt conventional Navier-Stokes solver for handling nonconservative equations. A primary type of application is to use transport equation turbulence models, but the extension is also possible for describing the transport of nonpassive scalars, such as in reactive media. Among others, combustion and gas dissociation phenomena are topics needing a considerable research effort. An implicit two step scheme based on the well-known MacCormack scheme has been modified to treat compressible turbulent flows on complex geometries. Implicit treatment of nonconservative equations (in the present case a two-equation turbulence model) opens the way to the coupled solution of thermochemical transport equations.
Here, an OpenACC directive-based graphics processing unit (GPU) parallel scheme is presented for solving the compressible Navier–Stokes equations on 3D hybrid unstructured grids with a third-order reconstructed discontinuous Galerkin method. The developed scheme requires the minimum code intrusion and algorithm alteration for upgrading a legacy solver with the GPU computing capability at very little extra effort in programming, which leads to a unified and portable code development strategy. A face coloring algorithm is adopted to eliminate the memory contention because of the threading of internal and boundary face integrals. A number of flow problems are presented to verify the implementation of the developed scheme. Timing measurements were obtained by running the resulting GPU code on one Nvidia Tesla K20c GPU card (Nvidia Corporation, Santa Clara, CA, USA) and compared with those obtained by running the equivalent Message Passing Interface (MPI) parallel CPU code on a compute node (consisting of two AMD Opteron 6128 eight-core CPUs (Advanced Micro Devices, Inc., Sunnyvale, CA, USA)). Speedup factors of up to 24× and 1.6× for the GPU code were achieved with respect to one and 16 CPU cores, respectively. The numerical results indicate that this OpenACC-based parallel scheme is an effective and extensible approach to port unstructured high-order CFD solvers to GPU computing.
This work presents a metric-based mesh adaptation capability added to the flow solver US3D that is used to improve the accuracy of atmospheric entry simulations. Flow past an entry vehicle in free-flight is usually unsteady and characterized by anisotropic flow features like a strong bow shock and small-scale isotropic flow features like turbulent eddies in the wake. The results presented in this paper demonstrate that we are currently able to iteratively apply metric-based mesh adaptation to improve the solution accuracy by simultaneously targeting isotropic and anisotropic flow features. A simplified workflow of running CFD simulations for entry vehicles is presented where we start off with a coarse initial mesh to compute a first approximation of the flow. This coarse mesh is then iteratively refined using the newly developed metric to improve the resolution of the CFD computation. Furthermore, we demonstrate that we are able to adapt large mesh sizes in a timely fashion which allows us to start thinking about applying this adaptive framework to unsteady atmospheric entry CFD simulations.
With the proper combination of high-order, low-dissipation numerical methods, physics-based subgrid-scale models, and boundary conditions it is becoming possible to simulate many combustion flows at relevant conditions. However, non-premixed flows are a particular challenge because the thickness of the fuel/oxidizer interface scales inversely with Reynolds number. Sharp interfaces can also be present in the initial or boundary conditions. When higher-order numerical methods are used, there are often aphysical undershoots and overshoots in the scalar variables (e.g.passive scalars, species mass fractions or progress variable). These numerical issues are especially prominent when low-dissipation methods are used, since sharp jumps in flow variables are not always coincident with regions of strong variation in the scalar fields: consequently, special detection mechanisms and dissipative fluxes are needed. Most numerical methods diffuse the interface, resulting in artificial mixing and spurious reactions. In this paper, we propose a numerical method that mitigates this issue. As a result, we present methods for passive and active scalars, and demonstrate their effectiveness with several examples.
The piecewise parabolic method and related schemes are widely used to model stellar flows. Several different methods for extending the validity of these methods to a general equation of state (EOS) have been proposed over time, but direct comparisons among one-another and exact solutions with stellar EOSs are not widely available. We introduce some simple test problems with exact solutions run with a popular stellar EOS and test how two existing codes with different approaches to incorporating general gases perform. The source code for generating the exact solutions is made available.
The microplasma thruster (MPT) concept is a simple extension of a cold gas micronozzle propulsion device, where a direct-current microdischarge is used to preheat the gas stream to improve the specific impulse of the device. Here we study a prototypical MPT device using a detailed, self-consistently coupled plasma and flow computational model. The model describes the microdischarge power deposition, plasma dynamics, gas-phase chemical kinetics, coupling of the plasma phenomena with high-speed flow, and overall propulsion system performance. Compared to a cold gas micronozzle, a significant increase in specific impulse is obtained from the power deposition in the diverging section of the MPT nozzle. For a discharge voltage of 750 V, a power input of 650 mW, and an argon mass flow rate of 5 SCCM (SCCM denotes cubic centimeter per minute at STP), the specific impulse of the device is increased by a factor of approx1.5 to about 74 s. The microdischarge remains mostly confined inside the micronozzle and operates in an abnormal glow discharge regime. Gas heating, primarily due to ion Joule heating, is found to have a strong influence on the overall discharge behavior. The study provides a validation of the MPT concept as a simple and effective approach to improve the performance of micronozzle cold gas propulsion devices.
The method of multiple scales is used to describe a formally correct method based on the nonparallel linear stability theory, that examines the two and three dimensional stability of compressible boundary layer flows. The method is applied to the supersonic flat plate layer at Mach number 4.5. The theoretical growth rates are in good agreement with experimental results. The method is also applied to the infinite-span swept wing transonic boundary layer with suction to evaluate the effect of the nonparallel flow on the development of crossflow disturbances.
This work deals with the building of a discrete model able to describe and to predict the evolution of complex gas flows in heterogeneous media. In many physical applications, large scales numerical simulation is no longer possible because of a lack of computing resources. Indeed the medium topology may be complex due to the presence of many obstacles (walls, pipes, equipments, geometric singularities etc.). Aircraft powerplant compartments are examples where topology is complex due to the presence of pipes, ducts, coolers and other equipment. Other important examples are gas explosions and large scale dispersion of hazardous materials in urban places, cities or underground involving obstacles such as buildings and various infrastructures. In all cases efficient safety responses are required. Then a new discrete model is built and solved in reasonable execution times for large cells volumes including such obstacles. Quantitative comparisons between experimental and numerical results are shown for different significant test cases, showing excellent agreement.
An investigation of a fixed-geometry, swept external-internal compression inlet was conducted at a Mach number of 6.0 and a test-section Reynolds number of 1.55 x 10 to the 7th power per meter. The test conditions was constant for all runs with stagnation pressure and temperature at 20 atmospheres and 500 K, respectively. Tests were made at angles of attack of -5 deg, 0 deg, 3 deg, and 5 deg. Measurements consisted of pitot- and static-pressure surveys in inlet throat, wall static pressures, and surface temperatures. Boundary-layer bleed was provided on the centerbody and on the cowl internal surface. The inlet performance was consistently high over the range of the angle of attack tested, with an overall average total pressure recovery of 78 percent and corresponding adiabatic kinetic-energy efficiency of 99 percent. The inlet throat flow distribution was uniform and the Mach number and pressure level were of the correct magnitude for efficient combustor design. The utilization of a swept compression field to meet the starting requirements of a fixed-geometry inlet produced neither flow instability nor a tendency to unstart.
In this work, a high-order accurate reconstructed discontinuous Galerkin (rDG) method is developed for solving two-dimensional hydrodynamic problems in cell-centered updated Lagrangian formulation. This method is the Lagrangian limit of the unsplit rDG-ALE formulation, and is obtained by assuming the equality of the grid velocity to the fluid velocity only at cell boundaries. The conservative variables and the Taylor basis defined on the time-dependent moving mesh, provide the piece-wise polynomial expansion in the updated Lagrangian formulation. A multi-directional nodal Riemann solver is implemented for computing the grid velocity at the vertices and the numerical flux at the cell boundaries. A characteristic limiting procedure is extended from the primitive variable version to the conservative variable version, and its performance is compared with the limiter on physical variables. A number of benchmark test cases are conducted to assess the accuracy, robustness, and non-oscillatory property of the DG(P0), DG(P1) and rDG(P1P2) methods. The numerical experiments demonstrate that the developed rDG method is able to attain the designed order of accuracy and the characteristic limiting procedure outperforms the limiter on physical variables in terms of the monotonicity and symmetry preservation for shock problems.
A k-epsilon model of turbulence that accounts for pressure gradients and compressibility effects is presented. To correct the degradation of k-epsilon model performance when pressure gradients are introduced, an extra term is added to the dissipation equation. By including this term and by adding terms to account for compressibility effects, a new k-epsilon model is developed for shear flows. The results show that the new model performs better than the existing k-epsilon models.