Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CO 2 capture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Matrimid substrates with bicontinuous surface and macrovoids in the bulk: A nearly ideal substrate for composite membranes in CO 2 capture

Scalable fabrication of thin-film composite (TFC) membrane for post-combustion carbon capture is often limited by the availability of high-performance nanoporous substrate. Ideally, the substrate should allow for fast gas transport at the selective layer/substrate interface as well as in the bulk of the substrate. In this study, highly permeable Matrimid substrates were prepared via vapor- and nonsolvent-induced phase separations. The phase separation mechanism of the Matrimid®/N-methyl-2-pyrrolidone casting solution was modulated by the addition of LiCl to control the solution thermodynamic stability, and nanoporous Matrimid substrates were formed with a bicontinuous surface and macrovoids in the bulk. This hierarchically optimized structure resulted in a CO 2 permeance of 2.60 × 10 5 GPU (1 GPU = 1 × 10 –6 cm 3 (STP) cm –2 s –1 cmHg –1 = 3.349 × 10 –10 mol m –2 s –1 Pa –1 ), which was ca. 11 times more permeable than a benchmark polyethersulfone substrate with cellular pores. The benefit of using this new substrate was demonstrated by coating a 170-nm amine-containing polymer to form a TFC facilitated transport membrane. The membrane exhibited a CO 2 permeance of 932 GPU at 57°C, which was 72 GPU higher than the counterpart coated on the benchmark substrate. Meanwhile, the CO 2 /N 2 selectivity was remained at 158. This permeance improvement could be well explained by the resistance-in-series model, where the improved permeance was attributed to the reductions in substrate and lateral diffusion mass transfer resistances. The upper bound (UB) analysis indicates that the Matrimid substrate is nearly ideal for the state-of-the-art polymers for CO 2 /N 2 separation. Here, the substrate improvement could also reduce the parasitic energy associated with the membrane process due to the reduced membrane cost and flue gas compression requirement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Design of Experiments for Dynamic Test Runs in Solvent-Based CO 2 Capture Pilot Plants

Test runs in the pilot plants consume significant resources, and therefore, the learning from test runs should be maximized. Test runs conducted in the pilot plants are often steady state. It takes several hours for reaching steady-state in the pilot plants, and thus, the duration of the test runs needs to be long even for collecting few steady-state data points. On the other hand, a large number of measurements can be collected through dynamic test runs in a short span of time. This paper presents a systematic design of dynamic experiments (DoDEs) for identifiability of model parameters, which is achieved by persistently exciting the inputs signals. A pseudorandom binary sequence (PRBS) is designed as the input signal for DoDE due to its efficiency in obtaining sufficient spectral content. However, due to the long sequence size of the PRBS signal, a Schroeder-phase input signal, which is a multisine signal, is also designed. Tests for both types of signals are run in the Pilot Solvent Test Unit (PSTU) at the National Carbon Capture Center in Wilsonville, Alabama. The transient data are used to solve dynamic data reconciliation and parameter estimation problem. The estimated parameters are found to be not only superior to those estimated from using data collected from hundreds of steady-state test runs in a nonreactive (air–water) system, but the parameters could be estimated by using the dynamic data collected for about 24 h from the pilot plant for the MEA-H 2 O–CO 2 system.

CO2 capture↗
DOE OSTI2024

Nitrogen–Rich Conjugated Macrocycles: Synthesis, Conductivity, and Application in Electrochemical CO 2 Capture

Here we report a series of nitrogen-rich conjugated macrocycles that mimic the structure and function of semiconducting 2D metal–organic and covalent organic frameworks while providing greater solution processability and surface tunability. Using a new tetraaminotriphenylene building block that is compatible with both coordination chemistry and dynamic covalent chemistry reactions, we have synthesized two distinct macrocyclic cores containing Ni–N and phenazine-based linkages, respectively. The fully conjugated macrocycle cores support strong interlayer stacking and accessible nanochannels. For the metal–organic macrocycles, good out-of-plane charge transport is preserved, with pressed pellet conductivities of 10 –3 S/cm for the nickel variants. Lastly, using electrochemically mediated CO2 capture as an example, we illustrate how colloidal phenazine-based organic macrocycles improve electrical contact and active site electrochemical accessibility relative to bulk covalent organic framework powders. Together, these results highlight how simple macrocycles can enable new synthetic directions as well as new applications by combining the properties of crystalline porous frameworks, the processability of nanomaterials, and the precision of molecular synthesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

An Electrochemically Mediated Amine Regeneration Process with a Mixed Absorbent for Postcombustion CO 2 Capture

Electrochemically mediated amine regeneration (EMAR) was recently developed to avoid the use of thermal means to release CO2 captured from postcombustion flue gas in the benchmark amine process. To address concerns related to the high vapor pressure of ethylenediamine (EDA) as the primary amine used in EMAR, a mixture of EDA and aminoethylethanolamine (AEEA) was investigated. The properties of the mixed amine systems, including the absorption rates, electrolyte pH and conductivity, and CO2 capacity, were evaluated in comparison with those of solely EDA. The mixed amine system had similar properties to that of EDA, indicating no significant changes would be necessary for the future implementation of the EMAR process with mixed amines as opposed to that with just EDA. The electrochemical performance of the mixed amines in terms of the cell voltage, gas desorption rate, electron utilization, and energetics was also investigated. A 50/50 mixture of EDA and AEEA displayed the lowest energetics: ~10% lower than that of 100% EDA. With this mixture, a continuous EMAR process, in which the absorption column was connected to the electrochemical cell as the desorption stage, was tested over 100 h. The cell voltage was very stable and there was a steady gas output close to theoretical values. The desorbed gas was further analyzed and found to be 100% CO2, confirming no evaporation of the amine. The mixed absorbent composition was also characterized using titration and nuclear magnetic resonance (NMR) spectroscopy, and the results showed no amine degradation. Furthermore, these findings that demonstrate a stable, low vapor pressure absorbent with improved energetics are promising and could be a guideline for the future development of EMAR for CO2 capture from flue gas and other sources.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Technoeconomic Analysis of the Electrochemically Mediated Amine Regeneration CO 2 Capture Process

The electrochemically mediated amine regeneration (EMAR) process presents an alternative route to the conventional thermal amine regeneration for carbon capture from a flue gas source. In this study, we conducted an economic analysis on the EMAR system for postcombustion CO2 capture from a 550 MWe power plant capturing 3.1 MtCO2 annually and from a mini steel mill with annual capture close to 170 ktCO2. We followed the recommendation of the National Energy Technology Laboratory (NETL) 2010 report to estimate the cost of CO2 avoided ([$/tCO2]). Detailed cost modeling of the electrochemical separation stage was conducted. This is integrated with the entire process flowsheet (e.g., including absorber, compressor, pumps, and other auxiliary equipment). Here, we identified the membrane cost as the dominant capital cost for the electrochemical separation train. At a membrane unit price of less than 10/m2, the CO2 capture cost can be reduced to below 50/tCO2 with optimized process conditions (e.g., desorption pressure and utilization of waste heat). Improvements in process design, cell construction, and solvent formulation may lead to additional reductions in the CO2 capture cost.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

CO 2 Capture Using Electrochemically Mediated Amine Regeneration

We describe the current status of our research on, and the development of, the Electrochemically Mediated Amine Regeneration (EMAR) process for the capture of CO2 from flue gases. The absorption step in the EMAR process is the same as in the widely used amine process, but the desorption step is accomplished electrochemically as opposed to by a thermal swing used in the amine process. Our laboratory unit has operated continuously for over 200 h, spanning 130 absorption/desorption cycles. We have established an understanding of the thermodynamics of the EMAR process and provided engineering estimates of key features (energetics and sizing) of this technology. The EMAR system does not rely on steam integration, making it a truly plug-and-play unit that can be easily deployed for a range of applications. The EMAR system can also be scaled-down for distributed, modular, and small-scale operations (e.g., stainless steel mini-mills, etc.). Here, results to date indicate that the EMAR process has the potential to be a viable option for post-combustion CO2 capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Capturing CO 2 in Quadrupolar Binding Pockets: Broadband Microwave Spectroscopy of Pyrimidine-(CO 2 ) n , n = 1,2

Pyrimidine has two in-plane CH(δ+)/N̈(δ–)/CH(δ+) binding sites that are complementary to the (δ–/2δ+/δ–) quadrupole moment of CO 2 . For this study, we recorded broadband microwave spectra over the 7.5–17.5 GHz range for pyrimidine-(CO 2 ) n with n = 1 and 2 formed in a supersonic expansion. Based on fits of the rotational transitions, including nuclear hyperfine splitting due to the two 14 N nuclei, we have assigned 313 hyperfine components across 105 rotational transitions for the n = 1 complex and 208 hyperfine components across 105 rotational transitions for the n = 2 complex. The pyrimidine-CO 2 complex is planar, with CO 2 occupying one of the quadrupolar binding sites, forming a structure in which the CO 2 is stabilized in the plane by interactions with the C–H hydrogens adjacent to the nitrogen atom. This structure is closely analogous to that of the pyridine-CO 2 complex studied previously by (Doran, J. L. J. Mol. Struct. 2012, 1019, 191–195). The fit to the n = 2 cluster gives rotational constants consistent with a planar cluster of C 2v symmetry in which the second CO 2 molecule binds in the second quadrupolar binding pocket on the opposite side of the ring. The calculated total binding energy in pyrimidine-CO 2 is –13.7 kJ mol –1 , including corrections for basis set superposition error and zero-point energy, at the CCSD(T)/ 6-311++G(3df,2p) level, while that in pyrimidine-(CO 2 ) 2 is almost exactly double that size, indicating little interaction between the two CO 2 molecules in the two binding sites. The enthalpy, entropy, and free energy of binding are also calculated at 300 K within the harmonic oscillator/rigid-rotor model. This model is shown to lack quantitative accuracy when it is applied to the formation of weakly bound complexes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗