Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Analog computation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Analysis of dynamic inlet distortion applied to a parallel compressor model

An investigation of surge was conducted by using a parallel compressor model of the J85-13 compressor implement on an analog computer. Surges were initiated by various types of dynamic disturbances in inlet pressure. The compressor model was less sensitive to disturbances of short duration, high frequency, and long duration where the compressor discharge pressure could react. Adding steady distortion to dynamic disturbances reduced the amount of dynamic disturbance required to effect surge. Steady and unsteady distortions combined linearly to reduce surge margin.

Wenzel, L. M.↗
NASA NTRS1976

The effect of varying freestream velocity on dynamic stall characteristics

A low speed wind tunnel equipped with an axial gust generator to simulate the aerodynamic environment of a helicopter rotor was used to study the dynamic stall of a pitching blade. The objective of this investigation was to find out to what extent harmonic velocity perturbations in the freestream affect dynamic stall. The study involved making measurements of the aerodynamic moment on a two-dimensional, pitching blade model in both constant and pulsating airstreams. Using an operational analog computer to perform on-line data reduction, plots of moment versus angle of attack and work done by the moment were obtained. The data taken in the varying freestream were then compared to constant freestream data, and to the results of two analytical methods. These comparisons showed that the velocity perturbations had a significant effect on the pitching moment which could not be consistently predicted by the analytical methods, but had no drastic effect on the blade stability.

Pierce, G. A.↗
NASA NTRS1977

Synthesis and implementation of state-trajectory control law for dc-to-dc converters

Mathematical representations of a state-plane switching boundary employed in a state-trajectory control law for dc-to-dc converters are derived. Two approaches to implementing the control law are discussed; one approach employs a digital processor and the other uses analog computational circuits. Performance characteristics of experimental voltage step-up dc-to-dc converters operating under the control of each of these implementations are presented.

Burns, W. W., III↗
NASA NTRS1978

Prospects of a mathematical theory of human behavior in complex man-machine systems tasks

A hierarchy of human activities is derived by analyzing automobile driving in general terms. A structural description leads to a block diagram and a time-sharing computer analogy. The range of applicability of existing mathematical models is considered with respect to the hierarchy of human activities in actual complex tasks. Other mathematical tools so far not often applied to man machine systems are also discussed. The mathematical descriptions at least briefly considered here include utility, estimation, control, queueing, and fuzzy set theory as well as artificial intelligence techniques. Some thoughts are given as to how these methods might be integrated and how further work might be pursued.

Johannsen, G.↗
NASA NTRS1979

Energy-state formulation of lumped volume dynamic equations with application to a simplified free piston Stirling engine

Lumped volume dynamic equations are derived using an energy state formulation. This technique requires that kinetic and potential energy state functions be written for the physical system being investigated. To account for losses in the system, a Rayleigh dissipation function is formed. Using these functions, a Lagrangian is formed and using Lagrange's equation, the equations of motion for the system are derived. The results of the application of this technique to a lumped volume are used to derive a model for the free piston Stirling engine. The model was simplified and programmed on an analog computer. Results are given comparing the model response with experimental data.

Daniele, C. J.↗
NASA NTRS1977

Fast-response free-running dc-to-dc converter employing a state-trajectory control law

A recently proposed state-trajectory control law for a family of energy-storage dc-to-dc converters has been implemented for the voltage step-up configuration. Two methods of realization are discussed; one employs a digital processor and the other uses analog computational circuits. Performance characteristics of experimental voltage step-up converters operating under the control of each of these implementations are reported and compared to theoretical predictions and computer simulations.

Huffman, S. D.↗
NASA NTRS1979

Energy-state formulation of lumped volume dynamic equations with application to a simplified free piston Stirling engine

Lumped volume dynamic equations are derived using an energy-state formulation. This technique requires that kinetic and potential energy state functions be written for the physical system being investigated. To account for losses in the system, a Rayleigh dissipation function is also formed. Using these functions, a Lagrangian is formed and using Lagrange's equation, the equations of motion for the system are derived. The results of the application of this technique to a lumped volume are used to derive a model for the free-piston Stirling engine. The model was simplified and programmed on an analog computer. Results are given comparing the model response with experimental data.

Daniele, C. J.↗
NASA NTRS1979

Magnetic suspension system for an Annular Momentum Control Device (AMCD)

A technique to control a rim suspended in a magnetic field was developed. A complete system was developed, incorporating a support structure, magnetic actuators, a rim drive mechanism, an emergency fail-safe system, servo control system, and control electronics. Open loop and closed loop response of the system at zero speed and at 500 revolutions per minute (r/min) of the rim was obtained and analyzed. The rim was then dynamically balanced and a rim speed of 725 r/min was achieved. An analog simulation of the hardware was developed and tested with the actual control electronics connected to the analog computer. The system under development is stable at rim speeds below 700 r/min. Test results indicate that the rim under test is not rigid. The rim has a warp and a number of binding modes which prevented achievement of higher speeds. Further development efforts are required to achieve higher rim speeds.

Source record↗
NASA NTRS1980

Single-stage electrohydraulic servosystem for actuating on airflow valve with frequencies to 500 hertz

An airflow valve and its electrohydraulic actuation servosystem are described. The servosystem uses a high-power, single-stage servovalve to obtain a dynamic response beyond that of systems designed with conventional two-stage servovalves. The electrohydraulic servosystem is analyzed and the limitations imposed on system performance by such nonlinearities as signal saturations and power limitations are discussed. Descriptions of the mechanical design concepts and developmental considerations are included. Dynamic data, in the form of sweep-frequency test results, are presented and comparison with analytical results obtained with an analog computer model is made.

Webb, J. A., Jr.↗
NASA NTRS1979

Mathematical concepts for modeling human behavior in complex man-machine systems

Many human behavior (e.g., manual control) models have been found to be inadequate for describing processes in certain real complex man-machine systems. An attempt is made to find a way to overcome this problem by examining the range of applicability of existing mathematical models with respect to the hierarchy of human activities in real complex tasks. Automobile driving is chosen as a baseline scenario, and a hierarchy of human activities is derived by analyzing this task in general terms. A structural description leads to a block diagram and a time-sharing computer analogy.

Johannsen, G.↗
NASA NTRS1980

Practical design considerations for a flightworthy higher harmonic control system

The paper discusses the design of a higher harmonic blade pitch control system for flight testing on an OH-6A helicopter. Alternative designs for both the mechanical and electronic subsystems are also presented. Among the recommendations set forth are: (1) use electronic analog methods instead of FFT software, delegating spectral analysis and self testing to an Electronic Control Unit; (2) use a digital rather than analog computer for increased flexibility in solution processing; and (3) locate HHC actuators in the nonrotating system and separate these actuators from the primary control system. It is concluded that a target weight for a prototype control system would be less than 1% of design gross weight and the production weight of the future HHC system may be 0.5 of the weight of the aircraft.

Wood, E. R.↗
NASA NTRS1980

A new controller for battery-powered electric vehicles

This paper describes the development, under a NASA/DOE contract, of a new concept for efficient and reliable control of battery-powered vehicles. It avoids the detrimental effects of pulsed-power controllers like the SCR 'chopper' by using rotating machines to meter continuous currents to the traction motor. The concept is validated in a proof-of-principle demonstration system and a complete vehicle is simulated on an analog computer. Test results show exceptional promise for a full-scale system. Optimum control strategies to minimize controller weight are developed by means of the simulated vehicle. The design for an Engineering Model is then prepared in the form of a practical, compact two-bearing package with forced air cooling. Predicted performance is outstanding, with controller efficiency of over 90% at high speed.

Belsterling, C. A.↗
NASA NTRS1981

Shock-free configurations in two-and three-dimensional transonic flow

Efforts to replace Sobieczky's complicated analog computations of solutions to the hodograph equations by a fast elliptic solver in order to generate shock-free airfoil designs more effectively are described. The indirect design of airfoil and wing shapes that are free from shock waves even though the local flow velocity exceeds the speed of sound is described. The problem of finding an airfoil in two dimensional, irrotational flow that has a prescribed pressure distribution is as addressed. Sobieczky's suggestion to use a fictitious gas for finding shock-free airfoils directly in the physical plane was the basis for a more efficient procedure for achieving the same end.

Seebass, A. R.↗
NASA NTRS1981

Advanced dc motor controller for battery-powered electric vehicles

A motor generation set is connected to run from the dc source and generate a voltage in the traction motor armature circuit that normally opposes the source voltage. The functional feasibility of the concept is demonstrated with tests on a Proof of Principle System. An analog computer simulation is developed, validated with the results of the tests, applied to predict the performance of a full scale Functional Model dc Controller. The results indicate high efficiencies over wide operating ranges and exceptional recovery of regenerated energy. The new machine integrates both motor and generator on a single two bearing shaft. The control strategy produces a controlled bidirectional plus or minus 48 volts dc output from the generator permitting full control of a 96 volt dc traction motor from a 48 volt battery, was designed to control a 20 hp traction motor. The controller weighs 63.5 kg (140 lb.) and has a peak efficiency of 90% in random driving modes and 96% during the SAE J 227a/D driving cycle.

Belsterling, C. A.↗
NASA NTRS1978

Two-dimensional dynamic stall as simulated in a varying freestream

A low speed wind tunnel equipped with a axial gust generator to simulate the aerodynamic environment of a helicopter rotor was used to study the dynamic stall of a pitching blade in an effort to ascertain to what extent harmonic velocity perturbations in the freestream affect dynamic stall. The aerodynamic moment on a two dimensional, pitching blade model in both constant and pulsating airstream was measured. An operational analog computer was used to perform on-line data reduction and plots of moment versus angle of attack and work done by the moment were obtained. The data taken in the varying freestream were then compared to constant freestream data and to the results of two analytical methods. These comparisons show that the velocity perturbations have a significant effect on the pitching moment which can not be consistently predicted by the analytical methods, but had no drastic effect on the blade stability.

Pierce, G. A.↗
NASA NTRS1982

A jet controlled magnetic referenced attitude control system for spinning payloads

An attitude control system was designed permitting large angle acquisition and alignment of the principle axis of a spinning payload to within 1 degree of the earth's magnetic field. Signals from magnetometer and gyro sensors are fed to the control algorithm to generate commands for the jet thrusters. The algorithm contains a cross axis magnetometer signal to prevent a large angle magnetometer signal to prevent a large angle equilibrium solution. The acquisition will occur within 50 seconds from initial precession and nutation angles of 30 degrees. An electronic spin filter passes signals at spin and nutation frequencies and rejects bias signals due to sensor misalignment and principle axis offset. Describing function analysis and total analog simulation techniques were used. The flight ACS hardware was interfaced with the analog computer simulation for design and verification. The controller has flown on four successful missions.

Celmer, J. J.↗
NASA NTRS1982

Improved pointing at trackable targets by integrating control valve signals

A compact, low-cost add-on electronic module has been developed for the STRAP III control system to improve pointing at trackable targets. The module provides peak-to-peak limit cycle excursions of + or - 5 arcseconds while tracking a +3 magnitude or brighter star. This is achieved without using rate-integrating gyroscopes, thus reducing payload length, weight, cost, and preparation time. This module has flown successfully five times. In May 1981, it improved the performance of a two-startracker attitude control system with TV camera and joystick control which pointed at a nontrackable target. This paper describes the operation of the module, how it alters the ordinary STRAP III operation, and how it was developed using an analog-computer-based rocket flight simulator.

Stone, R. W.↗
NASA NTRS1984

An analytical design procedure for the determination of effective leading edge extensions on thick delta wings

An analytical design procedure for leading edge extensions (LEE) was developed for thick delta wings. This LEE device is designed to be mounted to a wing along the pseudo-stagnation stream surface associated with the attached flow design lift coefficient of greater than zero. The intended purpose of this device is to improve the aerodynamic performance of high subsonic and low supersonic aircraft at incidences above that of attached flow design lift coefficient, by using a vortex system emanating along the leading edges of the device. The low pressure associated with these vortices would act on the LEE upper surface and the forward facing area at the wing leading edges, providing an additional lift and effective leading edge thrust recovery. The first application of this technique was to a thick, round edged, twisted and cambered wing of approximately triangular planform having a sweep of 58 deg and aspect ratio of 2.30. The panel aerodynamics and vortex lattice method with suction analogy computer codes were employed to determine the pseudo-stagnation stream surface and an optimized LEE planform shape.

Farhad Ghaffari↗