Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

EGS Collab Experiment 1: SIMFIP Notch-164 GRL Paper

Characterizing the stimulation mode of a fracture is critical to assess the hydraulic efficiency and the seismic risk related to deep fluid manipulations. We have monitored the three-dimensional displacements of a fluid-driven fracture during water injections in a borehole at ~1.5 km depth in the crystalline rock of the Sanford Underground Research Facility (USA). The fracture initiates at 61% of the minimum horizontal stress by micro-shearing of the borehole on a foliation plane. As the fluid pressure increases further, borehole axial and radial displacements increase with injection time highlighting the opening and sliding of a new hydrofracture growing ~10 m away from the borehole, in accordance with the ambient normal stress regime and in alignment with the microseismicity. Our study reveals how fluid-driven fracture stimulation can be facilitated by a mixed-mode process controlled by the complex hydromechanical evolution of the growing fracture. The data presented in this submission refer to the SIMFIP measurements and analyses of the stimulation tests conducted on the 164 ft (50 m) notch of the Sanford Underground Research Facility (SURF), during the EGS-Collab test 1. In addition to the datafiles, there is the draft of a manuscript submitted to Geophysical Research Letters (GRL).

15 GEOTHERMAL ENERGY↗

Experimental Investigation of Concrete Fatigue in Axial Compression

The use of concrete in fatigue critical structures, such as wind turbine towers, has necessitated the replacement of simplistic (and therefore insufficient) fatigue design recommendations with more accurate and advanced fatigue models that can consider a greater complexity of stress states and materials. As the first part of a multistage test series, an experimental investigation was conducted to determine the fatigue life of concrete subjected to axial compressive fatigue loading, focusing on the relatively high-cycle fatigue domain. Here, a wide range of values for maximum stress levels and stress ratios were considered. The experimental results were compared against existing predictive models, and the most applicable model was identified. Concrete strain and stiffness behavior during fatigue loading were also investigated and reported. Based on the observed behavior, a hypothesis for identifying the impending occurrence of fatigue failure, based on the monotonic stress-strain curve, is examined.

17 WIND ENERGY↗

Elastic moduli reduction in SiC-SiC tubular specimen after high heat flux neutron irradiation measured by resonant ultrasound spectroscopy

The initial results of a post-irradiation examination study conducted on a SiC-SiC tubular specimen irradiated under a high radial heat flux are presented herein. The elastic properties of the specimen were evaluated before and after the irradiation using the resonant ultrasound spectroscopy (RUS) technique. The composite tubular specimen was considered as an orthotropic elastic with nine elastic constants (Young's moduli, shear moduli and Poisson's ratios—three components of each) for representing its full elastic deformation behavior. All the elastic moduli decreased after irradiation; the reduction was as high as 35% in one of the moduli. The significant decrease in the moduli indicates the presence of microcracks. The results from a computational study show significant stress development in the specimen due to irradiation, primarily caused by differential swelling across the thickness of the specimen. The evaluated stresses exceed the proportional limit stress of the material, indicating the likelihood of matrix microcracking, and thus corroborating the results obtained from RUS. X-ray Computed Tomography (XCT) study confirmed the presence of cracks in the irradiated specimen. These cracks occurred at the inner region of the specimen and propagated in axial and hoop directions. Finally, these XCT results are in agreement with the RUS results and stress distribution results from the computational study.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Planar, longitudinal, compressive waves in solids: Thermodynamics and uniaxial strain restrictions

A new tri-axial pressure-based constitutive expression has been found using Cauchy's stress tensor. This stress state emphasizes pressure and shear stress. The description is a pressure plus an effective shear stress allowing for a constitutive law based on atomic solid-state phase changes in crystalline cells due to pressure plus shear-based dislocation motion commonly associated with plasticity. Pressure has a new role in the material's constitutive response as it is separated from plasticity. The thermo-mechanical system describes third-order Gibbs’ expressions without specific volume restrictions placed upon the material. Isothermally, the ratio of heat to shear work in elastic copper is shown to approach zero at a very low temperature and become larger than one as temperature approaches melting. Wave compression models investigated are elastic and plastic: in fully elastic materials, the planar wave is restricted by Poisson's effect although plastic shear changes this constraint. Plastic deformation, dominated by dissipative shear stresses in uniaxial strain, heats the material while excluding phase changes from hydrostatic pressures. The material properties per se across Hugoniot shocks are described with entropy concepts. Shock waves are exceedingly complex since the constitutive laws are linked at extreme temperatures, pressures, and shear stresses. Isothermal, isentropic, isochoric, and iso-shear conditions are used throughout with Jacobian algebra.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

EGS Collab Experiment 2: 4100 Foot Level Elastic Property Data

Static and dynamic elastic properties (Young's modulus, Shear Modulus, P-wave Modulus, and Poisson's Ratio) of amphibolites and rhyolites from the TV4100 and TH4100 boreholes at the Sanford Underground Research Laboratory (SURF). Elastic properties include Young's modulus, Poisson's ratio, shear modulus, and p-wave modulus. Raw data from the experiments and slides describing the experimental procedure and a summary of results are included, along with a readme file with additional definitions and information.

15 GEOTHERMAL ENERGY↗

Experimental deformation in sandstone, carbonates and quartz aggregate

The first part of my thesis is mainly focused on the effect of grain size distribution on compaction localization in porous sandstone. To identify the microstructural parameters that influence compaction band formation, I conducted a systematic study of mechanical deformation, failure mode and microstructural evolution in Bleurswiller and Boise sandstones, of similar porosity (~25%) and mineralogy but different sorting. Discrete compaction bands were observed to develop over a wide range of pressure in the Bleurswiller sandstone that has a relatively uniform grain size distribution. In contrast, compaction localization was not observed in the poorly sorted Boise sandstone. My results demonstrate that grain size distribution exerts important influence on compaction band development, in agreement with recently published data from Valley of Fire and Buckskin Gulch, as well as numerical studies. The second part aimed to improve current knowledge on inelastic behavior, failure mode and brittle-ductile transition in another sedimentary rock, porous carbonates. A micritic Tavel (porosity of ~13%) and an allochemical Indiana (~18%) limestones were deformed under compaction in wet and dry conditions. At lower confining pressures, shear localization occurred in brittle faulting regime. Through transitional regime, the deformation switched to cataclastic flow regime at higher confining pressure. Specifically in the cataclastic regime, the (dry and wet) Tavel and dry Indiana failed by distributed cataclastic flow, while in contrast, wet Indiana failed as compaction localization. My results demonstrate that different failure modes and mechanical behaviors under different deformation regimes and water saturation are fundamental prior to any geophysical application in porous carbonates. The third part aimed to focus on investigating compaction on quartz aggregate starting at low (MPa) using X-ray diffraction. We report the diffraction peak evolution of quartz with increasing pressures. Through evaluating the unit cell lattice parameters and the volume of the quartz sample, macroscopic stress and strain were resolved. Moreover, we observed quartz peak broadened asymmetrically at low pressure, such extent is more prominent in axial than in radial direction. Our evaluation on peak [101] (highest intensity among peaks) demonstrated that full width at half maximum can be a good proxy for microscopic stress distribution. We observed deviations in the pressurevolume curves at P = ~0.4 GPa and speculated that it was the point of which onset of grain crushing and pore collapse occur in quartz. This is on the same order of which onset of grain crushing (commonly known as P*) is observed in sandstones in the rock mechanics literature. This demonstrated that there is potential in estimating grain crushing and pore collapse pressure with our technique.

58 GEOSCIENCES↗

Prediction of continuous porosity gradients in ceramics using ZnO as a model material

Materials with gradient microstructures have a wide range of applications such as cutting tools, armor, and electronic devices. However, it is difficult to predict and control the gradient microstructure during processing. In the present work, a continuous porosity gradient was successfully achieved in ZnO material via spark plasma sintering with a large induced thermal gradient. The porosity is overestimated if isothermal prediction is applied. The current work proposed a more accurate prediction of the porosity by considering the stress-shielding effect caused by the thermal gradient. The shielding effect results from different stress states in the sample due to differential sintering: the hotter side of the specimen experiences a higher strain rate and more shrinkage while the colder side experiences a lower strain rate and less shrinkage simultaneously. Therefore, the axial strains are varied throughout the sample thickness. Using the constituent equations in advanced sintering analysis, the shield stress was calculated to be approximately 13 MPa for the viscoelastic assumption of sintering. To improve the accuracy of predicting porosity gradient, it is necessary to add a load to overcome the shield stress when the materials are sintered with a thermal gradient.

36 MATERIALS SCIENCE↗

Shock-induced transformation of nitinol shape memory alloy: Effect of stress state on transformation

Due to its numerous practical applications and intriguing phase transformation behavior, shape memory alloys (SMAs) have garnered significant research and development interests. In the past, most studies on the mechanical behavior of SMAs have been conducted under uniaxial stress loadings. Limited research on SMAs under shock loading has not provided conclusive results regarding their transformation behavior and transformation stress under such loading. Additionally, there is a lack of comprehensive understanding regarding the effects of different stress states on transformation behavior. The main objectives of this study are to address these issues. To achieve these objectives, a series of shock wave experiments were designed and conducted. Additionally, quasi-static and dynamic uniaxial stress experiments were carried out to establish a baseline for comparison. The results revealed that the transformation stress under dynamic uniaxial strain shock loading was approximately 1.92 GPa in contrast to 0.5 GPa (quasi-static) to 0.8 GPa (dynamic) observed in uniaxial stress loading. The transformation behavior exhibited noticeable rate sensitivity for both types of loading. There appeared to be a critical strain rate above which the austenite phase was driven to a metastable state. This estimated critical axial strain rate along the loading direction was approximately 2 × 10 3 /s–4 × 10 3 /s for uniaxial stress loading and approximately 2 × 10 6 /s for uniaxial strain loading. The apparent high transformation stress for uniaxial strain loading can likely be attributed to a combination of high-pressure confinement and high strain rate. Furthermore, determining their relative contributions remains an open issue.

36 MATERIALS SCIENCE↗

Mechanical characterization of an additively manufactured Inconel 718 theta-shaped specimen

Two sets of “theta”-shaped specimens were additively manufactured with Inconel 718 powders using an electron beam melting technique with two distinct scan strategies. Light optical microscopy, mechanical testing coupled with a digital image correlation (DIC) technique, finite element modeling, and neutron diffraction with in situ loading characterizations were conducted. The cross-members of the specimens were the focus. Light optical micrographs revealed that different microstructures were formed with different scan strategies. Ex situ mechanical testing revealed each build to be stable under load until ductility was observed on the cross-members before failure. The elastic moduli were determined by forming a correlation between the elastic tensile stresses determined from FEM, and the elastic strains obtained from DIC. The lattice strains were mapped with neutron diffraction during in situ elastic loading; and a good correlation between the average axial lattice strains on the cross-member and those determined from the DIC analysis was found. Lastly, the spatially resolved stresses in the elastic deformation regime are derived from the lattice strains and increased with applied load, showing a consistent distribution along the cross-member.

36 MATERIALS SCIENCE↗

Experimental and CFD Studies of Coolant Flow Mixing within Scaled Models of the Upper and Lower Plenums of NGNP Gas-Cooled Reactors

A 1/16th scaled VHTR experimental model was constructed and the preliminary test was performed in this study. To produce benchmark data for CFD validation in the future, the facility was first run at partial operation with five pipes being heated. PIV was performed to extract the vector velocity field for three adjacent naturally convective jets at statistically steady state. A small recirculation zone was found between the pipes, and the jets entered the merging zone at 3 cm from the pipe outlet but diverged as the flow approached the top of the test geometry. Turbulence analysis shows the turbulence intensity peaked at 41-45% as the jets mixed. A sensitivity analysis confirmed that 1000 frames were sufficient to measure statistically steady state. The results were then validated by extracting the flow rate from the PIV jet velocity profile, and comparing it with an analytic flow rate and ultrasonic flowmeter; all flow rates lie within the uncertainty of the other two methods for Tests 1 and 2. This test facility can be used for further analysis of naturally convective mixing, and eventually produce benchmark data for CFD validation for the VHTR during a PCC or DCC accident scenario. Next, a PTV study of 3000 images (1500 image pairs) were used to quantify the velocity field in the upper plenum. A sensitivity analysis confirmed that 1500 frames were sufficient to precisely estimate the flow. Subsequently, three (3, 9, and 15 cm) Y-lines from the pipe output were extracted to consider the output differences between 50 to 1500 frames. The average velocity field and standard deviation error that accrued in the three different tests were calculated to assess repeatability. The error was varied, from 1 to 14%, depending on Y-elevation. The error decreased as the flow moved farther from the output pipe. In addition, turbulent intensity was calculated and found to be high near the output. Reynolds stresses and turbulent intensity were used to validate the data by comparing it with benchmark data. The experimental data gave the same pattern as the benchmark data. A turbulent single buoyant jet study was performed for the case of LOFC in the upper plenum of scaled VHTR. Time-averaged profiles show that 3,000 frames of images were sufficient for the study up to second-order statistics. Self-similarity is an important feature of jets since the behavior of jets is independent of Reynolds number and a sole function of geometry. Self-similarity profiles were well observed in the axial velocity and velocity magnitude profile regardless of z/D where the radial velocity did not show any similarity pattern. The normal components of Reynolds stresses have self-similarity within the expected range. The study shows that large vortices were observed close to the dome wall, indicating that the geometry of the VHTR has a significant impact on its safety and performance. Near the dome surface, large vortices were shown to inhibit the flows, resulting in reduced axial jet velocity. The vortices that develop subsequently reduce the Reynolds stresses that develop and the impact on the integrity of the VHTR upper plenum surface. Multiple jets study, including two, three and five jets, were investigated.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Effect of Prestrain on the Fatigue Life of Superelastic Nitinol

Three types of fatigue testing are performed to elucidate the effects of prestraining superelastic Nitinol on its subsequent fatigue lifetime: rotary bending and tension–tension testing of wire, and beam bending using diamond-shaped specimens fabricated from tubing. Results show that local plastic deformation during prestraining induces residual stresses that have a pronounced effect on fatigue performance, enhancing performance when the fatigue duty cycle is of the same sense as the prestraining (tensile prestraining followed by a tensile duty cycle, for example), and decreasing fatigue lifetime when the sense of the duty cycle is opposite to that of prestraining. This provides an avenue to increasing fatigue lifetime, but more importantly it highlights the need to fully understand the nature of the duty cycle: for example, prestraining a stent by crimping it into a delivery catheter induces favorable residual stresses with respect to subsequent pulsatile fatigue, but might accelerate fracture in other modes, such as axial or crush fatigue. Caution is also advised when trying to apply data from “constant life diagrams” derived from the literature (Ref 1, 2 for example) that may not properly reflect the strain history of the device being analyzed.

36 MATERIALS SCIENCE↗

High-burnup Experiments in Reactivity Initiated Accidents (HERA)

HERA is a joint experimental program (JEEP) operating within the Nuclear Energy Agency’s (NEA’s) framework for irradiation experiments (FIDES). HERA is dedicated to the understanding of light water reactor (LWR) fuel performance at high burnup under reactivity-initiated accidents (RIA). During RIAs the fuel cladding can be breached by one of two mechanisms; pellet-cladding mechanical interaction or high temperature balloon and rupture. Pellet-cladding mechanical interaction (PCMI) failure occurs in the early phase of an RIA transient where the fuel pellet expands rapidly into the cladding prior to any meaningful heat transfer from the pellet to the cladding. This results in high stresses in the cladding resulting in crack propagation through the base Zircaloy metal and axially along the cladding tube. Failure by PCMI is a brittle failure mode and occurs at low cladding strains, approximately 2% hoop strain. If the cladding survives the PCMI phase of the transient, it may still fail due to ballooning and rupture induced by extended exposure to high temperature. Thermal transport from the fuel pin to the coolant is significantly reduced if a transition to film boiling on the cladding surface occurs. This result in both a rapid increase in fuel temperature, which drives fission gas release, and a spike in cladding temperature, which results in loss of mechanical strength. If the internal pressure of the fuel rod is greater than the system pressure the cladding can inelastically deform and eventually rupture. Failure by swelling and rupture occurs at larger strains, generally greater than 5% hoop strain. While PCMI failures are generally seen as more limiting, the dominance of one failure mode over the other can be affected by both the cladding material conditions, and the transient evolution.

(HERA)↗

High-burnup Experiments in Reactivity Initiated Accidents (HERA)

HERA is a joint experimental program (JEEP) operating within the Nuclear Energy Agency’s (NEA’s) framework for irradiation experiments (FIDES). HERA is dedicated to the understanding of light water reactor (LWR) fuel performance at high burnup under reactivity-initiated accidents (RIA). During RIAs the fuel cladding can be breached by one of two mechanisms; pellet-cladding mechanical interaction or high temperature balloon and rupture. Pellet-cladding mechanical interaction (PCMI) failure occurs in the early phase of an RIA transient where the fuel pellet expands rapidly into the cladding prior to any meaningful heat transfer from the pellet to the cladding. This results in high stresses in the cladding resulting in crack propagation through the base Zircaloy metal and axially along the cladding tube. Failure by PCMI is a brittle failure mode and occurs at low cladding strains, approximately 2% hoop strain. If the cladding survives the PCMI phase of the transient, it may still fail due to ballooning and rupture induced by extended exposure to high temperature. Thermal transport from the fuel pin to the coolant is significantly reduced if a transition to film boiling on the cladding surface occurs. This result in both a rapid increase in fuel temperature, which drives fission gas release, and a spike in cladding temperature, which results in loss of mechanical strength. If the internal pressure of the fuel rod is greater than the system pressure the cladding can inelastically deform and eventually rupture. Failure by swelling and rupture occurs at larger strains, generally greater than 5% hoop strain. While PCMI failures are generally seen as more limiting, the dominance of one failure mode over the other can be affected by both the cladding material conditions, and the transient evolution.

(HERA)↗

Mechanical Response of Cr-Coated Zircaloy-4 Cladding to Pellet-Cladding Interactions

Chromium-coated zircaloy is a promising accident tolerant fuel (ATF) cladding design which can help mitigate high temperature oxidation. The mechanical response of the cladding during and after loading may be altered by the Cr coating throughout anticipated operational and accident occurrences such as a pellet-cladding interaction (PCI). In this work, the mechanical behavior of Cr-coated and uncoated cold worked stress-relieved (CWSR) Zircaloy-4 (Zry-4) cladding to PCI loading conditions are studied. Stress relaxation tests are performed on CWSR Zry-4 cladding using full-tube axial tension and internal pressurization to investigate mechanical anisotropy and rate-limiting deformation mechanisms of the uncoated Zry-4. These results are compared to internal pressure testing results of similar cladding with physical vapor deposition (PVD) Cr-coating to reveal how the Cr-coating affects the cladding mechanical response. Findings are discussed in the context of ATF cladding performance during operation and storage.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Planar turbulent wakes under pressure gradient: Integral and self-similarity analyses

By using a combination of integral and self-similarity analyses, the generalized analytical solutions for the mean transverse velocity and Reynolds shear stress are rigorously derived for the first time for the far field of planar turbulent wakes under arbitrary pressure gradients. Specifically, by assuming self-similarity for the mean axial velocity, the analytical formulation for the mean transverse velocity is obtained from the integral of the mean continuity equation, and the analytical formulation for the Reynolds shear stress is obtained from the integral of the momentum equation. The generalized analytical formulations for the mean transverse velocity and Reynolds shear stress consist of multiple components, each with its unique scale and physical mechanism. In the zero pressure gradient limit, the generalized formulations recover the single-scale equations reported by Wei, Liu, and Livescu. Furthermore, simpler approximate formulations for the mean transverse velocity and Reynolds shear stress are also obtained, and show excellent agreement with the experimental measurements. Here, the findings provide new insights into the properties of planar turbulent wakes under pressure gradients, filling some long-standing gaps in the existing literature.

42 ENGINEERING↗

Cold Sintered Ceramics and Cements for Part Encapsulation

In this project, ceramic encapsulation materials were studied for high temperature (>~°500 C) applications where typical polymer encapsulants are unstable. A new low temperature (<~°200 C) method of processing ceramics, the cold sintering process was examined. Additionally, commercially available high temperature ceramic cements were investigated. In both cases, the mechanical strengths of available materials are less than desired (i.e., desired strengths similar to Si 3 N 4 ), limiting applicability. Composite designs to increase mechanical strength are suggested. Additionally, non-uniformities in stresses and densification while embedding alumina sheets in encapsulants via cold sintering using uni-axial pressing led to fracture of sheets, and an alternative iso-static based approach is recommended for future studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Review of the Research and Development of Brayton Cycle Technology in Nuclear Power Applications with a Focus on Compressor Technology

This study reviews the integration of Brayton Cycle (BC) systems in nuclear power generation, emphasizing their potential to enhance thermal efficiency and operational flexibility over traditional Rankine Cycle (RC) systems. Key working fluids, such as helium (He), supercritical carbon dioxide (sCO 2 ), nitrogen (N 2 ), and air, are evaluated for their performance, efficiency, and compatibility with nuclear systems. He is recognized for its high thermal conductivity and inertness at elevated temperatures, while sCO 2 demonstrates advantages in compactness and efficiency in midrange temperatures. This article also highlights the importance of compressor designs in optimizing BC performance and reviews, available compressor technologies. Axial and centrifugal compressor designs enable efficient gas compression while managing the thermal and mechanical stresses associated with high-pressure operations in nuclear systems. Combined with variable geometry components and advanced materials, these technologies address the challenges posed by varying load conditions. Despite the promising features of BC systems, several challenges persist, including high leakage rates and material degradation under extreme conditions, which necessitate robust sealing technologies and thorough testing. The insights gained from operational experiences at facilities, such as the Oberhausen II plant and the High-Temperature He Test Facility (HHV), underscore the complexities involved in designing high-temperature gas turbines for nuclear applications. This review concludes that as the nuclear industry evolves, BC systems hold significant promise for contributing to a sustainable energy future, particularly in the context of small modular reactors (SMRs) and microreactors. Further exploration of combined cycle configurations that combine BCs with RCs may enhance overall efficiency and flexibility in power generation.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗