Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Research on relation between bending stress and characteristic frequency of H-shaped beam by free vibration deflection

In order to investigate a relation between a bending stress and a characteristic frequency of a beam, 4-point loading which had constant moment region was conducted to a beam with H shape configuration experimentally and numerically. H-shaped beam has many characteristic deformation modes. Axial tensile stress in the beam made its characteristic frequency higher, and compressive stress lower. In the experiment, some characteristic frequencies got higher by a bending stress, and the others stayed in a small frequency fluctuation. The distinction is anticipated as a capability to measure a bending stress of a beam by its characteristic frequencies.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Mobilization of colloidal particles by low-frequency dynamic stress stimulation

Naturally occurring seismic events and artificially generated low-frequency (1 to 500 Hertz) elastic waves have been observed to alter the production rates of oil and water wells, sometimes increasing and sometimes decreasing production, and to influence the turbidity of surface and well water. The decreases in production are of particular concern - especially when artificially generated elastic waves are applied as a method for enhanced oil recovery. The exact conditions that result in a decrease in production remain unknown. While the underlying environment is certainly complex, the observed increase in water well turbidity after natural seismic events suggests the existence of a mechanism that can affect both the subsurface flow paths and mobilization of in-situ colloidal particles. This paper explores the macroscopic and microscopic effects of low-frequency dynamic stress stimulations on the release of colloidal particles from an analog core representing an infinitesimal section along the propagation paths of an elastic wave. Experiments on a column packed with 1-mm borosilicate beads and loaded with polystyrene microspheres demonstrate that axial mechanical stress oscillations enhance the mobilization of captured microspheres. Increasing the amplitude of the oscillations increases the number of microspheres released and can also result in cyclical spikes in effluent microsphere concentration during stimulation. Under a prolonged period of stimulation, the cyclical effluent spikes coincided with fluctuations in the column pressure data, and continue at a diminished level after stimulation. This behavior can be attributed to rearrangements of the beads in the column, resulting in possible changes to the void space and/or tortuosity of the packing. Optical microscopy observations of the beads during low frequency oscillations reveal that individual beads rotate, thereby rubbing against each other and scraping away portions of the adsorbed microspheres. These results support the theory that mechanical interactions between porous matrix grains are important mechanisms in flow path alteration and the mobilization of naturally occurring colloidal particles during elastic wave stimulation. These results also point to both continuous and discrete, en masse releases of colloidal particles, perhaps due to circulation cells within the packing material.

58 GEOSCIENCES↗

Influences of Processing and Fatigue Cycling on Residual Stresses in a NiCrY-Coated Powder Metallurgy Disk Superalloy

Oxidation and corrosion can attack superalloy disk surfaces exposed to increasing operating temperatures in some turbine engine environments. Any potential protective coatings must also be resistant to harmful fatigue cracking during service. The objective of this study was to investigate how residual stresses evolve in one such coating. Fatigue specimens of a powder metallurgy-processed disk superalloy were coated with a NiCrY coating, shot peened, and then subjected to fatigue in air at room and high temperatures. The effects of this processing and fatigue cycling on axial residual stresses and other aspects of the coating were assessed. While shot peening did induce beneficial compressive residual stresses in the coating and substrate, these stresses relaxed in the coating with subsequent heating. Several cast alloys having compositions near the coating were subjected to thermal expansion and tensile stress relaxation tests to help explain this response of residual stresses in the coating. For the coated fatigue specimens, this response contributed to earlier cracking of the coating than for the uncoated surface during long intervals of cycling at 760 °C. Yet, substantial compressive residual stresses still remained in the substrate adjacent to the coating, which were sufficient to suppress fatigue cracking there. The coating continued to protect the substrate from hot corrosion pitting, even after fatigue cracks initiated in the coating.

36 MATERIALS SCIENCE↗

Approximations for column effect in airplane wing spars

The significance attaching to "column effect" in airplane wing spars has been increasingly realized with the passage of time, but exact computations of the corrections to bending moment curves resulting from the existence of end loads are frequently omitted because of the additional labor involved in an analysis by rigorously correct methods. The present report represents an attempt to provide for approximate column effect corrections that can be graphically or otherwise expressed so as to be applied with a minimum of labor. Curves are plotted giving approximate values of the correction factors for single and two bay trusses of varying proportions and with various relationships between axial and lateral loads. It is further shown from an analysis of those curves that rough but useful approximations can be obtained from Perry's formula for corrected bending moment, with the assumed distance between points of inflection arbitrarily modified in accordance with rules given in the report. The discussion of general rules of variation of bending stress with axial load is accompanied by a study of the best distribution of the points of support along a spar for various conditions of loading.

Warner, Edward P↗

Axial Fatigue Tests at Zero Mean Stress of 24S-T Aluminum-alloy Sheet with and Without a Circular Hole

Axial fatigue tests were made on 189 coupon specimens of 0.032-inch 24S-T aluminum-alloy sheet and a few supplementary specimens of 0.004-inch sheet. The mean load was zero. The specimens were restrained against lateral buckling by lubricated solid guides described in a previous report on this project. About two-thirds of the 0.032-inch specimens were plain coupons nominally free from stress raisers. The remainder contained a 0.1285-inch drilled hole at the center where the reduced section was 0.5 inch wide. S-N diagrams were obtained for cycles to failure between about 1000 and 10 to the 7th power cycles for the plain specimens and 17 and 10 to the 7th power cycles for the drilled specimens. The fatigue stress concentration factor increased from about 1.08 for a stress amplitude causing failure at 0.25 cycles (static) to a maximum of 1.83 at 15,000 cycles and then decreased gradually. The graph for the drilled specimens showed less scatter than that for the plain specimens.

TESTING MACHINES, FATIGUE↗

Experimental Techniques Verified for Determining Yield and Flow Surfaces

Structural components in aircraft engines are subjected to multiaxial loads when in service. For such components, life prediction methodologies are dependent on the accuracy of the constitutive models that determine the elastic and inelastic portions of a loading cycle. A threshold surface (such as a yield surface) is customarily used to differentiate between reversible and irreversible flow. For elastoplastic materials, a yield surface can be used to delimit the elastic region in a given stress space. The concept of a yield surface is central to the mathematical formulation of a classical plasticity theory, but at elevated temperatures, material response can be highly time dependent. Thus, viscoplastic theories have been developed to account for this time dependency. Since the key to many of these theories is experimental validation, the objective of this work (refs. 1 and 2) at the NASA Lewis Research Center was to verify that current laboratory techniques and equipment are sufficient to determine flow surfaces at elevated temperatures. By probing many times in the axial-torsional stress space, we could define the yield and flow surfaces. A small offset definition of yield (10 me) was used to delineate the boundary between reversible and irreversible behavior so that the material state remained essentially unchanged and multiple probes could be done on the same specimen. The strain was measured with an off-the-shelf multiaxial extensometer that could measure the axial and torsional strains over a wide range of temperatures. The accuracy and resolution of this extensometer was verified by comparing its data with strain gauge data at room temperature. The extensometer was found to have sufficient resolution for these experiments. In addition, the amount of crosstalk (i.e., the accumulation of apparent strain in one direction when strain in the other direction is applied) was found to be negligible. Tubular specimens were induction heated to determine the flow surfaces at elevated temperatures. The heating system induced a large amount of noise in the data. By reducing thermal fluctuations and using appropriate data averaging schemes, we could render the noise inconsequential. Thus, accurate and reproducible flow surfaces (see the figure) could be obtained.

Lerch, Brad A.↗

Thrust measurement in a 2-D scramjet nozzle

The two-dimensional thrust nozzle presents a challenging problem. The loading is not axisymmetric as in the case of a cone and the internal flow presents some design difficulties. A two-sting system has been chosen to accomodate the internal flow and achieve some symmetry. The situation is complicated by the fact that with the small ramp angle and the internal pressure on the nozzle walls, loading is predominantly transverse. Yet it is the axial thrust which is to be measured (i.e., the tensile waves propagating in the stings). Although bending stress waves travel at most at only 60% of the speed of the axial stress waves, the system needs to be stiffened against bending. The second sting was originally only used to preserve symmetry. However, the pressures on each thrust surface may be quite different at some conditions, so at this stage the signals from both stings are being averaged as a first order approximation of the net thrust. The expected axial thrust from this nozzle is not large so thin stings are required. In addition, the contact area between nozzle and sting needs to be maximized. The result was that it was decided to twist the stings through 90 deg, without distorting their cross-sectional shape, just aft of the nozzle. Finite element analysis showed that this would not significantly alter the propagation of the axial stress wave in the sting, while the rigidity of the system is greatly increased. A Mach 4 contoured nozzle is used in the experiments. The thrust calculated by integrating the static pressure measurements on the thrust surfaces is compared with the deconvolved strain measurement of the net thrust for the cases of air only and hydrogen fuel injected into air at approximately 9 MJ/kg nozzle supply enthalpy. The gain in thrust due to combustion is visible in this result.

Tuttle, Sean↗

Graphene nanoplatelets reinforced cement as a solution to leaky wellbores reinforcing weak points in hydrated Portland cement with graphene nanoparticles improves mechanical and chemical durability of wellbore cements

In this work, to improve the performance of wellbore cement under subsurface environments, graphene nanoplatelets (GNPs) were added in various percentages to Class-H cement slurry. Microstructural characterization of cement slurries cured at 90 °C and 95% RH indicates that GNP modifies the microstructure of hydrated cement by reinforcing pore spaces. As a result, the mechanical properties, such as Young's modulus and axial peak stress, obtained from high temperature triaxial compression tests are significantly improved based on different percentages of added GNPs. Furthermore, the hydrated 1 × 2 inch GNP- Portland cement cores tested under simulated deep wellbore conditions of high-temperature and high pressure (HTHP), appear to have a ductile-like behavior, when compared to a typical brittle nature of Portland cement pastes. From our observations and published data on graphene resistance to fracture, GNP addition to cement is evidently enhancing the flexibility of cement. These improvements would reduce the risks associated with wellbore cement deterioration and a consequent leakage in fossil fuel production, geothermal energy production, CO 2 storage as well as long-term sealing materials in plugging and abandonment of all wellbores at the end of their service life.

36 MATERIALS SCIENCE↗

Design, Test and Demonstration of Fault Current Limiting HTS Transformer

The project developed new technology that enables the creation of a high temperature superconductor-based FCL power transformer. SuperPower’s research and development created new methods to bond HTS conductor to a supporting substrate, test, and insulate the resulting bonded conductor, reduce winding ac losses, ensure FCL functionality during a transformer fault and build firm superconducting joints in the transformer harnesses and cabling. The bonded conductor in this program was shown to meet the critical operating parameters of providing the superconducting transformer operation while being able to meet the target normal state resistance required for FCL operation. The bonded conductor was also shown to be able to handle the fabrication stresses associated with the manufacture of the FCL transformer while also being able to handle the high hoop stresses and axial forces during a fault transient. Much of the technology developed here is applicable to the broader applied superconductivity community. The ability to tailor the clad conductors performance characteristics gives the designer of devices utilizing HTS a broader capability to address the particular needs of an given application. SuperPower worked with its sub-recipients Waukesha Electric Systems, ORNL, Southern California Edison and University of Houston to develop the design, fabrication, installation and operational aspects of a fault current limiting transformer on the electrical grid.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Stability optimization of laminated composite plates

The optimum design of plates with orthotropic layers under axial compression and shear is discussed. The plates considered are the laminates of N orthotropic layers whose principal material axes coincide with the plate axes. Each layer is assumed to have the same thickness and an equal number of fibers in the direction of + alpha sub i and - alpha sub i with respect to the plate axis. The fiber directions which give the highest axial buckling stress and the highest shear buckling stress are found by utilizing a mathematical optimization technique for various aspect ratios of the plates. Inhomogeneity in the direction of the plate thickness (stacking sequence) is taken into account in this analysis.

Hirano, Y.↗

Design, Fabrication and Test of Composite Curved Frames for Helicopter Fuselage Structure

Aspects of curved beam effects and their importance in designing composite frame structures are discussed. The curved beam effect induces radial flange loadings which in turn causes flange curling. This curling increases the axial flange stresses and induces transverse bending. These effects are more important in composite structures due to their general inability to redistribute stresses by general yielding, such as in metal structures. A detailed finite element analysis was conducted and used in the design of composite curved frame specimens. Five specimens were statically tested and compared with predicted and test strains. The curved frame effects must be accurately accounted for to avoid premature fracture; finite element methods can accurately predict most of the stresses and no elastic relief from curved beam effects occurred in the composite frames tested. Finite element studies are presented for comparative curved beam effects on composite and metal frames.

Lowry, D. W.↗

Mean-flow measurements in a supersonic three-dimensional turbulent boundary layer

Measurements are presented of the mean flow in a supersonic turbulent boundary layer subjected to a constant weak transverse pressure gradient. The temperature and longitudinal velocity and the axial shear stress were only slightly affected by the three-dimensionality but a clearly defined crossflow component appeared, in the manner suggested by theory and confirmed in earlier experiments. The flow deflection angle and transverse-velocity component achieved a self-preserving form so long as the transverse-pressure gradient remained constant, and both achieved a maximum at the sublayer edge; the deflection angle seemed to decrease again between the latter and the surface. An empirical relation was found between the pressure-gradient strength and the maximum in the crossflow, and the dependence of the latter on distance from the surface was used to test analytical crossflow predictions. The data are in general agreement with Van Den Berg's law of the wall. The data also support the so-called parabolic law following a relaxation distance, especially if inviscid gradients are accounted for, and if the normal coordinate is contracted by the compressibility transformation.

Demetriades, A.↗

Instability of capillary jets with thermocapillarity

Long axisymmetric liquid zones are subject to axial temperature gradients which induce steady viscous flows driven by thermocapillarity. The approximately parallel flow in a cylindrical zone is examined for linearized instabilities. Capillary, surface-wave and thermal modes are found. Capillary breakup can be retarded or even suppressed for small Prandtl number and large Biot number B, which measures heat transfer from the liquid to the surrounding atmosphere. In the limiting case B approaches infinity the zone becomes an isothermal jet subject to axial 'wind stress' on its interface. It is then possible to suppress capillary breakup entirely so that one can maintain long coherent jets.

Xu, J.-J.↗

Turbine blade forced response prediction using FREPS

This paper describes a software system called FREPS (Forced REsponse Prediction System) that integrates structural dynamic, steady and unsteady aerodynamic analyses to efficiently predict the forced response dynamic stresses in axial flow turbomachinery blades due to aerodynamic and mechanical excitations. A flutter analysis capability is also incorporated into the system. The FREPS system performs aeroelastic analysis by modeling the motion of the blade in terms of its normal modes. The structural dynamic analysis is performed by a finite element code such as MSC/NASTRAN. The steady aerodynamic analysis is based on nonlinear potential theory and the unsteady aerodynamic analyses is based on the linearization of the non-uniform potential flow mean. The program description and presentation of the capabilities are reported herein. The effectiveness of the FREPS package is demonstrated on the High Pressure Oxygen Turbopump turbine of the Space Shuttle Main Engine. Both flutter and forced response analyses are performed and typical results are illustrated.

Murthy, Durbha, V.↗