Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ASMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

FY25 status report on the addition of candidate materials in Class B Code Case

This report provides the time-dependent allowable stress calculation strategy leveraging the limited creep rupture tests data generated to support the allowable stress for 100,000 hours in American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC), Section II, Part D. A variable confidence index procedure to extrapolate material properties to support 500,000 hours design life is discussed. Time-dependent allowable stresses for Class B component design and analysis are presented for Grade 1 and Grade 2 of Alloy 625. The presented data extrapolation and allowable stress calculation method will support new material addition using limited creep rupture data in the new ASME Boiler and BPVC, Section III, Division 5, Class B rules.

Part D↗
DOE OSTI2023

Critical Evaluation of a Novel Analysis Technique for Assessment of Printed Circuit Heat Exchangers in High-Temperature Nuclear Service

Application of printed circuit heat exchangers (PCHEs) to very high-temperature reactors (VHTRs) requires mechanical performance assessment methodologies. The PCHE morphology consists of thousands of millimeter-scale channels, for enhanced thermal efficiency, enclosed in a meter-scale PCHE core. PCHE geometry under thermomechanical creep-fatigue transients results in multi-axial interactions between its different segments, such as channeled core, walls, and headers. These global-level interactions influence the local channel-level responses. Hence, developing a PCHE performance assessment methodology, following the ASME Code, Section III, Division 5 provisions, is a critical gap to be filled. There is no analysis or design methodology available in ASME Code to assess a PCHE for its global and local level performances under high temperature and pressure loadings. This paper critically evaluates a recently proposed two-step analysis technique to estimate global interactions and local channel-level responses of PCHEs. In this novel analysis technique, the channeled PCHE core is replaced with orthotropic solid blocks of representative stiffness properties for the global thermomechanical analysis. Here, subsequent channel scale submodel analysis with detailed channel geometry, loading, and elastic-perfectly plastic (EPP) material model estimates the local responses for PCHE performance assessment. This paper critically evaluates this novel technique for its effectiveness in PCHE performance assessment. Finite element (FE) models imitating various analysis issues are developed, and FE analysis results are scrutinized. An important outcome of this study is the validation of the novel two-step PCHE analysis technique for application to the performance assessment of PCHEs in VHTRs.

42 ENGINEERING↗
NASA NTRS2018

The Chaotic Long-Term X-Ray Variability of 4U 1705-44

The low-mass X-ray binary 4U1705-44 exhibits dramatic long-term X-ray time variability with a time-scale of several hundred days. The All-SkyMonitor (ASM) aboard the Rossi X-ray Timing Explorer (RXTE) and the Japanese Monitor of All-sky X-ray Image (MAXI) aboard the International Space Station together have continuously observed the source from 1995 December through 2014 May. The combined ASM-MAXI data provide a continuous time series over 50 times the length of the time-scale of interest. Topological analysis can help us identify 'fingerprints' in the phase space of a system unique to its equations of motion. The Birman-Williams theorem postulates that if such fingerprints are the same between two systems, then their equations of motion must be closely related. The phase-space embedding of the source light curve shows a strong resemblance to the double-welled non-linear Duffing oscillator. We explore a range of parameters for which the Duffing oscillator closely mirrors the time evolution of 4U1705-44. We extract low period, unstable periodic orbits from the 4U1705-44 and Duffing time series and compare their topological information. The Duffing and 4U1705-44 topological properties are identical, providing strong evidence that they share the same underlying template. This suggests that we can look to the Duffing equation to help guide the development of a physical model to describe the long-term X-ray variability of this and other similarly behaved X-ray binary systems.

Rossi X-ray Timing Explorer (RXTE)↗
DOE OSTI2024

DOE ART Graphite R&D Introduction

Introduction of ART Graphite R&D to include oxidation activities, oxidation resistant graphite, model development, ASME component failure, ASME code development (design rules), ceramic composites, AGC update, molten salt intrusion, split-disk studies, wear testing, and concluding remarks.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Class B Materials Code Case

Class B Materials Code Case to include: FY25 - High temperature design methodology, overview of ASME Section III (Division 5), Design for elevated temperature service, Goal to address current gaps, evaluation of proposed rules, allowable stress development, Class A materials (existing ASME approach), variable confidence index, data extrapolation, bounding value for SEE, and next steps.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Effect of various post-extrusion tempering on performance of AA2024 tubes fabricated by shear assisted processing and extrusion

In this report aluminum alloy 2024 (AA2024) tubes were extruded using the shear assisted processing and extrusion (ShAPE) method. As a ubiquitous aerospace alloy, AA2024 has reached a high degree of maturity with respect to manufacturing processes, alloy chemistry and heat treatment to maximize material strength. Therefore, over the eight decades since the introduction of this alloy, the mechanical properties have plateaued, and the extrusion speed has reached a 3.5 m/min ceiling using conventional extrusion. The ShAPE technique enabled an extrusion speed of AA2024 up to 7.4 m/min at 480 °C which is surpassing the extrudability chart of this alloy. Variation of the standard T3510 and T8510 post extrusion heat treatments were applied to improve the mechanical performance of the ShAPE extruded AA2024 tube. The ultimate tensile strength and yield strength of AA2024-T8510 ShAPE extruded tube are 522.0 ± 3.3 MPa and 510.7 ± 3.3 MPa, which are respectively 18% and 32% higher than ASM-typical and ASTM minimum values. The elongation at break of ShAPE extruded AA2024-T8510 tubes is two times higher than the ASM-typical and ASTM-minimum values. This improved ductility is attributed to the refinement of grain size and secondary phases as well as due to the uniform dispersion of sub-micron strengthening precipitates formed during the ShAPE process.

42 ENGINEERING↗
DOE OSTI2022

Aggregate attack surface management for network discovery of operational technology

Interconnectivity has become a substratum of technology as the benefits of data-driven functionality are being realized in nearly all industries. Increased connectivity of Operational Technology (OT) exacerbates cyber risks because Industrial Control Systems (ICS) are becoming exposed to the Internet. These exposures are often done inadvertently through misconfigurations as additional network devices come online. Attack surface management (ASM) platforms can be used to identify vulnerabilities by performing external network discovery over the Internet using web spiders. These web spiders enable big data analytics of Internet of Things (IoT) devices as identifiable information of Internet-exposed equipment are archived in searchable databases that are made publicly available. There are a multitude of ASM service providers on the market. Here, this study was conducted to evaluate several commonly known tools to determine the aggregate attack surface of control systems. Queries were crafted by targeting commonly known manufacturers and communication protocols found in OT networks. Identified devices were that categorized based on technology types. Each query was replicated between several tools to target identical ICS equipment. Findings in this paper suggested a significant variance in the exposures discovered by each tool, but unique contributions were identified for each tool when a merged attack surface was derived. Therefore, all tools should be used in aggregate.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Consistency of fatigue crack growth behavior of pipeline and low-alloy pressure vessel steels in gaseous hydrogen

Here, this study investigates the fatigue crack growth rate (FCGR) behavior of pipeline and low-alloy pressure vessel steels in high-pressure gaseous hydrogen. Despite a broad range of yield strengths and microstructures ranging from ferrite/pearlite, acicular ferrite, bainite, and martensite, the FCGR in gaseous hydrogen remained consistent (falling within a factor of 2–3). Steels with higher fractions of pearlite, typical of older vintage pipeline steels, exhibited modestly lower crack growth rates in gaseous hydrogen compared to steels with lower fractions of pearlite. Crack growth rates in these materials exhibit a systematic dependence on stress ratio and partial pressure of hydrogen, as captured in the recently published fatigue design curves in ASME B31 code case 220 for pipeline steels and ASME BPVC code case 2938 for pressure-vessel steels.

08 HYDROGEN↗
DOE OSTI2021

High speed manufacturing of aluminum alloy 7075 tubing by Shear Assisted Processing and Extrusion (ShAPE)

Shear assisted processing and extrusion (ShAPE) was used to extrude aluminum alloy 7075 tubing at speeds up to 12.2 m/min. This is in comparison to 2.0 m/min which is generally the limit for conventionally extruded 7075. The increased speed is primarily attributed to more extensive shear deformation, compared to conventional extrusion, which results in a high density of low angle grain boundaries that facilitate continued deformation and delay the onset of surface tearing. Mechanical testing after heat treating to the T6 condition gave an ultimate tensile strength of 565.3 ± 4.6 MPa, yield strength of 495.7 ± 8.7 MPa, and elongation of 16.8 ± 0.8%. Strength values exceed the ASTM minimum standard and are on par with ASM typical values, while elongation was substantially improved compared to 7 and 11% for the ASTM and ASM values respectively. Finally, it was observed that low temperature extrusion at 341 °C and 40 rpm gave superior material properties in the T6 condition compared to high temperature extrusion at 441 °C and 120 rpm due to variances in nanoscale second phase size and distribution.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure-based prediction of thermal aging strength reduction factors for grade 91 ferritic-martensitic steel

This study aimed to develop a microstructure-based mechanistic approach to address the long-term thermal aging effect on yield stress and ultimate tensile strength and to provide a physical basis for developing thermal aging factors for G91 for a design life of 60 years. Several heats of G91 steel were examined. Controlled aging experiments were conducted on two heats at temperatures of 550, 600, and 650 °C for times up to ~64,000 h. Specimens were also taken from archived creep-tested specimens of G91 and from a tube removed from the Kingston coal-fired power plant to obtain data that cover a wide range of temperatures and for aging times up to 155,000 h. Thermal aging caused significant subgrain recovery, coarsening of M 23 C 6 carbides at subgrain boundaries and MX carbonitrides within subgrains. The intermetallic Laves phase forms during aging and grows rapidly. The growth rate of the subgrain width and MX mean size during thermal aging were described by kinetic models. Thermal aging results in the reductions in the yield stress and the ultimate tensile strength of G91. The effects of thermal aging on the reductions in yield stress and ultimate tensile strength were well described by the microstructure-strength model that considers three superimposed strengthening mechanisms, namely, sub-boundary strengthening, MX precipitation hardening, and Mo solid solution strengthening. Furthermore, the model was independently validated by the ASME Code values and is being used by the ASME to develop the aging-induced strength reduction factors for G91 steel for a design life of 60 years.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Abundant Nitrate and Nitric Acid Aerosol in the Upper Troposphere and Lower Stratosphere

The tropospheric and stratospheric nitrate aerosol is simulated by a sectional aerosol model coupled to the Community Earth System Model. The simulated nitrate mass fractional contribution to aerosols is significantly higher in the upper troposphere and lower stratosphere (UTLS) than that at the surface. Both in situ measurements and simulations show that nitrate aerosol accounts for about 30%–40% of the aerosol mass at the tropopause of the Asian summer monsoon (ASM) region. Furthermore, simulated condensed nitric acid particles account for ~20% of the annual mean aerosol mass at the tropical tropopause, and over 95% in the UTLS at the South Pole in June-July-August. Here, our study suggests that the extremely cold ambient conditions in the UTLS of the tropics, ASM and polar regions thermodynamically favor the condensation of ammonia and nitric acid. The widely distributed nitrate aerosol in the global UTLS may be overlooked by climate models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

X-ray spectral and flux variability of the microquasar GRS 1758-258 on timescales from weeks to years

We present the spectral and timing evolution of the persistent black hole X-ray binary GRS 1758-258 based on almost 12 years of observations using the Rossi X-ray Timing Explorer Proportional Counter Array. While the source was predominantly found in the hard state during this time, it entered the thermally dominated soft state seven times. In the soft state GRS 1758-258 shows a strong decline in flux above 3 keV rather than the pivoting flux around 10 keV more commonly shown by black hole transients. In its 3–20 keV hardness intensity diagram, GRS 1758-258 shows a hysteresis of hard and soft state fluxes typical for transient sources in outburst. The RXTE-PCA and RXTE-ASM long-term light curves do not show any orbital modulations in the range of 2–30 d. However, in the dynamic power spectra significant peaks drift between 18.47 and 18.04 d for the PCA data, while less significant signatures between 19 d and 20 d are seen for the ASM data as well as for the Swift/BAT data. We discuss different models for the hysteresis behavior during state transitions as well as possibilities for the origin of the long term variation in the context of a warped accretion disk.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Performance Comparison of Helium and sCO 2 as Coolants for Modular Finger-Type Divertors

Several studies at the Georgia Institute of Technology have evaluated the thermal and fluids performance of the helium-cooled modular divertor with multiple jets (HEMJ) over the past decade. This finger-type divertor was studied both experimentally at nearly prototypical conditions and numerically at fully prototypical operating conditions using experimentally validated simulations. Recently, supercritical carbon dioxide (sCO 2 ) has been studied as the primary coolant in power cycles and other applications in various systems, in part because CO 2 achieves the high densities typical of supercritical fluids at relatively low temperatures and pressures, with a critical point of (7.38 MPa, 31°C). This density makes it possible to realize very compact and efficient sCO 2 power cycles. The feasibility of sCO 2 as a coolant for plasma-facing components, specifically the divertor, was therefore evaluated as part of the Fusion Energy System Studies design study activities. This work compares the thermal-fluid performance of helium and sCO 2 in the HEMJ divertor geometry using numerical simulations at prototypical conditions: inlet temperatures T i = 600°C to 700°C, pressures p ≈ 10 MPa, and steady-state incident heat fluxes on the tile q″ < 17 MW/m 2 . The performance is quantified here as the maximum heat flux that can be accommodated by the plasma-facing tile, the pumping power fraction, defined as the ratio of the coolant pumping power to the incident thermal power, and the operating stress limits based on ASME pressure vessel criteria. As expected, helium requires lower mass flow rates and pumping power fractions within imposed maximum temperature limits for the HEMJ pressure boundary. However, it also appears that neither helium nor sCO 2 can remove 10 MW/m 2 of incident heat flux while meeting ASME pressure vessel criteria. Finally, the numerical modeling reveals that sCO 2 may remove slightly higher incident heat fluxes than helium due to the imposed stress limits due to the sCO 2 coolant resulting in smaller local temperature gradients, albeit at a considerably higher pumping power fraction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Parameter Reduction of Composite Load Model Using Active Subspace Method

Over the past decades, the increasing penetration of distributed energy resources (DERs) has dramatically changed the power load composition in the distribution networks. The traditional static and dynamic load models can hardly capture the dynamic behavior of modern loads especially for fault-induced delayed voltage recovery (FIDVR) events. Thus, a more comprehensive composite load model with combination of static load, different types of induction motors, single-phase A/C motor, electronic load and DERs has been proposed by Western Electricity Coordinating Council (WECC). However, due to the large number of parameters and model complexity, the WECC composite load model (WECC CMLD) raises new challenges to power system studies. To overcome these challenges, in this paper, a cutting-edge parameter reduction (PR) approach for WECC CMLD based on active subspace method (ASM) is proposed. Firstly, the WECC CMLD is parameterized in a discrete-time manner for the application of the proposed method. Then, parameter sensitivities are calculated by discovering the active subspace, which is a lower-dimensional linear subspace of the parameter space of WECC CMLD in which the dynamic response is most sensitive. The interdependency among parameters can be taken into consideration by our approach. Finally, the numerical experiments validate the effectiveness and advantages of the proposed approach for WECC CMLD model.

active subspace↗
DOE OSTI2020

Opportunities and Challenges in Metal Forming for Lightweighting: Review and Future Work

Abstract The purposes of this review are to summarize the historical progress in the last 60 years of lightweight metal forming, to analyze the state-of-the-art, and to identify future directions in the context of Cyber-physically enabled circular economy. In honoring the 100th anniversary of the establishment of the Manufacturing Engineering Division of ASME, this review paper first provides the impact of the metal forming sector on the economy and historical perspectives of metal forming research work published by the ASME Journal of Manufacturing Science and Engineering, followed by the motivations and trends in lightweighting. To achieve lightweighting, one needs to systematically consider: (1) materials and material characterization; (2) innovative forming processes; and (3) simulation tools for integrated part design and process design. A new approach for process innovation, i.e., the Performance-Constraints-Mechanism-Innovation (PCMI) framework, is proposed to systematically seek new processes. Finally, trends and challenges for the further development in circular economy are presented for future exploration.

Engineering↗
DOE OSTI2021

Convection in Scaled Turbine Internal Cooling Passages With Additive Manufacturing Roughness

Abstract Additive manufacturing processes, such as direct metal laser sintering (DMLS), enable the creation of novel turbine cooling internal passages and systems. However, the DMLS method produces a significant and unique surface roughness. Previous work in scaled passages analyzed pressure losses and friction factors associated with the rough surfaces, as well as investigated the velocity profiles and turbulent flow characteristics within the passage. In this study, the heat transfer characteristics of scaled additively manufactured surfaces were measured using infrared (IR) thermography. Roughness panels were CNC machined from plates of aluminum 6061 to create near isothermal roughness elements when heated. Fluid resistance differences between the aluminum roughness panels and roughness panels constructed from ABS plastic using the same roughness patterns from McClain et al. (2020, “Flow in a Simulated Turbine Blade Cooling Channel With Spatially Varying Roughness Caused by Additive Manufacturing Orientation,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-16069) were investigated. Finally, the overall thermal performance enhancements and friction losses were assessed through the calculation of surface averaged “global thermal performance” ratios. The global thermal performance characterizations indicate results in-line with those found for traditional commercial roughness and slightly below traditional internal passage convection enhancement methods such as swirl chambers, dimples, and ribs. The passages investigated in this study do not include compressibility effects or the long-wavelength artifacts and channel geometric deviations observed by Wildgoose et al. (2020, “Impact of Additive Manufacturing on Internal Cooling Channels with Varying Diameters and Build Directions,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-15049). However, the results of this study indicate that, based on the roughness augmentation alone, artificial convective cooling enhancers such as turbulators or dimples may still be required for additively manufactured turbine component cooling.

Engineering↗
DOE OSTI2023

Manufacturing and Hydro Testing of a 10 MWe sCO2 Axial Turbine

Abstract Supercritical CO2 (sCO2) power cycles designed for thermodynamic efficiencies above 50% push component designs into pressure and temperature combinations that approach the limits of American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code and ASME Piping Design Codes with Turbine inlet conditions near 250 bar and 715 °C. These design conditions which limit available materials to high nickel alloys are compounded by the high fluid densities of sCO2 at these conditions which result in very compact machinery at the 10 MWe class which are currently being developed for the DOE supercritical transformational electric power (STEP) program. Design of the STEP Turbine is complete with integrated lessons learned from a previous 1 MWth subscale demonstration of a high temperature 10 MWe Turbine designed under the DOE SunShot Program. Fabrication of the STEP Turbine is nearing completion with all housings and pressure containing components in hand. This paper provides a detailed look at design intentions and limitations for the pressurized sections of the main pressure casing and the fabrication of key turbine components. Additional discussion is provided regarding postfabrication inspection and acceptance of the casing for use after issues with casing welds were identified late in the fabrication process.

Engineering↗