Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AIRPLANES - STRENGTH CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1940

A Full-scale Investigation of the Effect of Several Factors on the Shimmy of Cantering Wheels

A full-scale investigation has been conducted to determine the effect of various factors on the shimmy of castering wheels. The factors considered were the geometric arrangement, the tire types, the variations of load, the spindle moment of inertia, and the tire inflation. A comparison of the results of the present investigation with those calculated from existing theory was made. The constants needed in the calculations to determine the damping required for a castering wheel were measured. The results indicate that solid friction appears to be impracticable as the sole damping agent for castering nose wheels on large airplanes. Also it was concluded that the existing theory is adequate for calculating the damping required to prevent shimmy. The caster angle and the spindle moment of inertia were found to influence the solid friction required to prevent shimmy. The effect of variations in the type and the pressure of the tire was insignificant.

Howard, Walter B , Jr↗
NASA NTRS1989

A closed-form trim solution yielding minimum trim drag for airplanes with multiple longitudinal-control effectors

Airplane designs are currently being proposed with a multitude of lifting and control devices. Because of the redundancy in ways to generate moments and forces, there are a variety of strategies for trimming each airplane. A linear optimum trim solution (LOTS) is derived using a Lagrange formulation. LOTS enables the rapid calculation of the longitudinal load distribution resulting in the minimum trim drag in level, steady-state flight for airplanes with a mixture of three or more aerodynamic surfaces and propulsive control effectors. Comparisons of the trim drags obtained using LOTS, a direct constrained optimization method, and several ad hoc methods are presented for vortex-lattice representations of a three-surface airplane and two-surface airplane with thrust vectoring. These comparisons show that LOTS accurately predicts the results obtained from the nonlinear optimization and that the optimum methods result in trim drag reductions of up to 80 percent compared to the ad hoc methods.

Goodrich, Kenneth H.↗
NASA NTRS1973

Preliminary study of an integral fan lift/cruise engine for a 100 passenger VTOL transport

A simplified mission analysis was performed to determine an optimum engine cycle for a 100-passenger VTOL transport with a range of 500 statute miles. The aircraft had a total of eight integral fan lift engines, three of which serve as cruise engines. Fan pressure ratio was varied from 1.2 to 1.3, overall pressure ratio from 7 to 13, and turbine inlet temperature from 2460 to 2860 R. Bypass ratio was selected to meet a 500-foot altitude flyover noise goal of 95 PNdB. Airplane gross weight and direct operating cost (DOC) were calculated. The lowest DOC of 1.82 cents per seat-mile was achieved with a fan pressure ratio of 1.3, overall pressure ratio of 12, and turbine inlet temperature of 2860 R.

Civinskas, K. C.↗
NASA NTRS1976

Resume and analysis of NACA lateral control research

An analysis of the principal results of recent lateral control research is made. Two things are considered of primary importance in judging the effectiveness of different control devices: The (calculated) banking and yawing motion of a typical small airplane caused by a deflection of the control, and the stick force required to produce this deflection. The report includes a table in which a number of different lateral control devices are compared on these bases. Test flights demonstrated that satisfactory lateral control at high angles of attack depends as much on the retention of stability as on aileron effectiveness.

Weick, F. E.↗
NASA NTRS1979

Vibration characteristics of walls and a plate glass window representative of those of a wood-frame house

Mechanical excitation was used, and measurements of acceleration response, natural frequencies, and nodal patterns were performed. Results indicate that the wall sections and the complete wall did not act as a unit in responding to sinusoidal vibration inputs. Calculated frequencies of the components that account for this independent behavior of the studs and face sheets agreed resonably well with experimental frequencies. Experimental vibrations of the plate glass window agreed with the calculated behavior, and responses of the window exposed to airplane flyover noise were readily correlated with the test results.

Carden, H. D.↗
NASA NTRS1954

A study of the application of power-spectral methods of generalized harmonic analysis to gust loads on airplanes

The applicability of some results from the theory of generalized harmonic analysis (or power-spectral analysis) to the analysis of gust loads on airplanes in continuous rough air is examined. The general relations for linear systems between power spectrums of a random input disturbance and an output response are used to relate the spectrum of airplane load in rough air to the spectrum of atmospheric gust velocity. The power spectrum of loads is shown to provide a measure of the load intensity in terms of the standard deviation (root mean square) of the load distribution for an airplane in flight through continuous rough air. For the case of a load output having a normal distribution, which appears from experimental evidence to apply to homogeneous rough air, the standard deviation is shown to describe the probability distribution of loads or the proportion of total time that the load has given values. Thus, for airplane in flight through homogeneous rough air, the probability distribution of loads may be determined from a power-spectral analysis. In order to illustrate the application of power-spectral analysis to gust-load analysis and to obtain an insight into the relations between loads and airplane gust-response characteristics, two selected series of calculations are presented. The results indicate that both methods of analysis yield results that are consistent to a first approximation.

Press, Harry↗
NASA NTRS1937

Resume and analysis of NACA lateral control research

An analysis of the principal results of recent NACA lateral control research is made by utilizing the experience and progress gained during the course of the investigation. Two things are considered of primary importance in judging the effectiveness of different control devices: the (calculated) banking and yawing motion of a typical small airplane caused by a deflection of the control, and the stick force required to produce this deflection. The report includes a table in which a number of different lateral control devices are compared on these bases.

Weick, Fred E↗
NASA NTRS1932

Increase in the maximum lift of an airplane wing due to a sudden increase in its effective angle of attack resulting from a gust

Wind-tunnel tests are described, in which the angle of attack of a wing model was suddenly increased (producing the effect of a vertical gust) and the resulting forces were measured. It was found that the maximum lift coefficient increases in proportion to the rate of increase in the angle of attack. This fact is important for the determination of the gust stresses of airplanes with low wing loading. The results of the calculation of the corrective factor are given for a high-performance glider and a light sport plane of conventional type.

Kramer, Max↗
NASA NTRS2001

A Sensor-Independent Gust Hazard Metric

A procedure for calculating an intuitive hazard metric for gust effects on airplanes is described. The hazard metric is for use by pilots and is intended to replace subjective pilot reports (PIREPs) of the turbulence level. The hazard metric is composed of three numbers: the first describes the average airplane response to the turbulence, the second describes the positive peak airplane response to the gusts, and the third describes the negative peak airplane response to the gusts. The hazard metric is derived from any time history of vertical gust measurements and is thus independent of the sensor making the gust measurements. The metric is demonstrated for one simulated airplane encountering different types of gusts including those derived from flight data recorder measurements of actual accidents. The simulated airplane responses to the gusts compare favorably with the hazard metric.

Stewart, Eric C.↗
NASA NTRS1959

Semiempirical Procedure for Estimating Lift and Drag Characteristics of Propeller-Wing-Flap Configurations for Vertical-and Short-Take-Off-and-Landing Airplanes

The analysis presented uses the momentum theory as a starting point in developing semiempirical expressions for calculating the effect of propeller thrust and slipstream on the lift and drag characteristics of wing-flap configurations that would be suitable for vertical-take-off-and-landing (VTOL) and short-take-off-and-landing (STOL) airplanes. The method uses power-off forward-speed information and measured slipstream deflection data at zero forward speed to provide a basis for estimating the lift and drag at combined forward speed and power-on conditions. A correlation of slipstream deflection data is also included. The procedure is applicable only in the unstalled flight regime; nevertheless, it should be useful in preliminary design estimates of the performance that may be expected of VTOL and STOL airplanes.

Kuhn, Richard E.↗
NASA NTRS1956

An investigation of the loads on the vertical tail of a jet-bomber airplane resulting from flight through rough air

Vertical-tail loads were measured in turbulent air on a four-engine jet bomber. Results showed large load oscillations which were lightly damped. Comparison of experimental results with discrete-load calculations indicated that discrete-gust calculations underestimated the loads by 30 to 40 percent and gave no indication of the low damping. Power spectral analysis, on the other hand, indicated the general frequency characteristics and gave a somewhat better estimate of the peak-load distributions. The present results strongly suggest that discrete-gust calculation for gust loads on vertical tails may seriously underestimate the gust loads for airplanes having lightly damped lateral oscillations.

GUSTS, FREQUENCY↗
NASA NTRS1995

Electromagnetic compatibility and the all-electric airplane

NASA is studying the feasibility of installing 'all-electric' controls in future commercial aircraft, replacing the current hydraulic and pneumatic systems. Planes utilizing such equipment should weigh less and be cheaper to maintain, but might also be susceptible to interference from undesired external electromagnetic fields. Possible sources of these extraneous signals include radio and television broadcasters, two-way communications stations, and radar installations of all kinds. One way to reduce the hazard would be to use fiber-optic cables to carry signals from the cockpit to the various points of use, a concept known as 'fly-by-light' or FBL. However, electrical circuits (PBW, or 'power-by-wire') would still be required at both ends of the cables to perform control functions, so the possibility of harmful interference would remain. Computer models for two different antennas were created in order to find the magnitude of the electric fields which would be generated in the airspace around them while in the transmit mode. The first antenna was a horizontal 'rhombic' used by the Voice of America (VOA) for long-distance short-wave broadcasting. The second antenna was a multi-element 'log-periodic dipole array' (LPDA) of a type often used for two-way radio communications. For each case, a specified amount of power was applied in the computer model, and the resulting electric field intensity was predicted at a variety of locations surrounding the antenna. This information will then be used to calculate the levels of interference which could occur inside an airplane flying in the vicinity of these radiation emitters.

Christman, Al↗
NASA NTRS1944

NACA Investigation of a Jet-Propulsion System Applicable to Flight

Following a brief history of the NACA investigation of jet-propulsion, a discussion is given of the general investigation and analyses leading to the construction of the jet-propulsion ground-test mock-up. The results of burning experiments and of test measurements designed to allow quantitative flight-performance predictions of the system are presented and correlated with calculations. These calculations are then used to determine the performance of the system on the ground and in the air at various speeds and altitudes under various burning conditions. The application of the system to an experimental airplane is described and some performance predictions for this airplane are made. It was found that the main fire could be restricted to an intense, small, and short annular blue flame burning steadily and under control in the intended combustion space. With these readily obtainable combustion conditions, the combustion chamber the nozzle walls and the surrounding structure could be maintained at normal temperatures. The system investigated was found to be capable of burning one-half the intake air up the fuel rates of 3 pounds per second. Calculations were shown to agree well with experiment. It was concluded that the basic features of the jet-propulsion system investigation in the ground-test mock-up were sufficiently developed to be considered applicable to flight installation. Calculations indicated that an airplane utilizing this jet-propulsion system would have unusual capabilities in the high-speed range above the speeds of conventional aircraft and would, in addition, have moderately long cruising ranges if only the engine were used.

DUCTS↗
NASA NTRS1991

A controls engineering approach for analyzing airplane input-output characteristics

An engineering approach for analyzing airplane control and output characteristics is presented. State-space matrix equations describing the linear perturbation dynamics are transformed from physical coordinates into scaled coordinates. The scaling is accomplished by applying various transformations to the system to employ prior engineering knowledge of the airplane physics. Two different analysis techniques are then explained. Modal analysis techniques calculate the influence of each system input on each fundamental mode of motion and the distribution of each mode among the system outputs. The optimal steady state response technique computes the blending of steady state control inputs that optimize the steady state response of selected system outputs. Analysis of an example airplane model is presented to demonstrate the described engineering approach.

Arbuckle, P. Douglas↗
NASA NTRS1980

Wind-tunnel/flight correlation study of aerodynamic characteristics of a large flexible supersonic cruise airplane (XB-701) 2: Extrapolation of wind-tunnel data to full-scale conditions

The results of calculations necessary to extrapolate performance data on an XB-70-1 wind tunnel model to full scale at Mach numbers from 0.76 to 2.53 are presented. The extrapolation was part of a joint program to evaluate performance prediction techniques for large flexible supersonic airplanes similar to a supersonic transport. The extrapolation procedure included: interpolation of the wind tunnel data at the specific conditions of the flight test points; determination of the drag increments to be applied to the wind tunnel data, such as spillage drag, boundary layer trip drag, and skin friction increments; and estimates of the drag items not represented on the wind tunnel model, such as bypass doors, roughness, protuberances, and leakage drag. In addition, estimates of the effects of flexibility of the airplane were determined.

Peterson, J. B., Jr.↗
NASA NTRS1985

Preliminary design study of a lateral-directional control system using thrust vectoring

A preliminary design of a lateral-directional control system for a fighter airplane capable of controlled operation at extreme angles of attack is developed. The subject airplane is representative of a modern twin-engine high-performance jet fighter, is equipped with ailerons, rudder, and independent horizontal-tail surfaces. Idealized bidirectional thrust-vectoring engine nozzles are appended to the mathematic model of the airplane to provide additional control moments. Optimal schedules for lateral and directional pseudo control variables are calculated. Use of pseudo controls results in coordinated operation of the aerodynamic and thrust-vectoring controls with minimum coupling between the lateral and directional airplane dynamics. Linear quadratic regulator designs are used to specify a preliminary flight control system to improve the stability and response characteristics of the airplane. Simulated responses to step pilot control inputs are stable and well behaved. For lateral stick deflections, peak stability axis roll rates are between 1.25 and 1.60 rad/sec over an angle-of-attack range of 10 deg to 70 deg. For rudder pedal deflections, the roll rates accompanying the sideslip responses can be arrested by small lateral stick motions.

Lallman, F. J.↗