SEARCH · Engineering Papers

Results for “vortex generators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1988

An experimental study of rotor-vortex interactions

A scheme for investigating general blade/vortex interactions (BVIs) has been used to obtain an unusual body of data. The scheme involves locating a vortex generator upstream of a nonlifting rotor so that the vortex interacts with the rotor at any desired forward azimuth. Parallel BVIs produced by this external vortex generator are shown to be nearly identical to those produced by the rotor alone operating in a normal descent mode. The test delineates various generic features of parallel and oblique BVIs. However, the dominant feature is the leading-edge pressure pulse. The effects of blade/vortex angle, and proximity (including head-on interactions) on this pulse are discussed. The effect of Mach number on the leading edge pressure variation is shown to be small even for supercritical interactions.

Caradonna, F. X.↗

NASA NTRSDate not supplied

Wind-US Simulations of the NASA 1507 Inlet Test Case

Steady-state, Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) simulations were performed of the NASA 1507 Inlet Test Case from the 6th AIAA Propulsion Aerodynamics Workshop (PAW) held in January 2023 using the Wind-US CFD solver. The simulations were performed with bleed regions modeled as surface patches and the Slater bleed boundary condition models were applied within those regions. Both the constant-plenum-pressure and the fixed-plenum-exit bleed models where applied. The vortex generators were modeled using the Bender-Anderson-Yagle (BAY) vortex generator model. The CFD simulations were performed for inlet engine-face flow ratios varying from supercritical to subcritical inlet operation until inlet unstart. The results of the CFD simulations were compared to wind-tunnel data which included boundary layer profiles, axial static pressure distributions, bleed rates, total pressure recovery performance curves, and engine-face total pressure rake profiles. The CFD simulations were able to match most of the boundary layer rake data near the geometric throat, but the boundary layers on the centerbody were thinner than indicated by the wind-tunnel data. For the supercritical CFD simulations, the engine-face flow ratio was at least 2% to 2.5% lower than indicated by the wind-tunnel data, but still consistent with the level of supercritical bleed. The engine-face flow rates of the wind-tunnel tests had an uncertainty of ±2% which could explain the differences. The supercritical engine-face flow rates of the wind-tunnel data indicated a 5% supercritical bleed rate rather than the reported 7.18% bleed rate. The CFD simulations were able to calculate the maximum total pressure recovery of pt2/pt = 0.907 as observed for the wind-tunnel data. The CFD simulations with the constant-pressure bleed model were able to obtain a much lower engine-face total pressure ratio than indicated by both the wind-tunnel data and the CFD simulations using a fixed-plenum-exit bleed model. The CFD simulations indicated a sharp static pressure rise for the terminal shock rather than a more gradual rise indicated by the wind-tunnel data. The CFD simulations were not able to accurately compute the total pressure variation across the engine-face total pressure rake.

Supersonics↗

NASA NTRS1975

Lee surface flow phenomena over Space Shuttle at large angles of attack at M infinity = 6

An investigation was conducted regarding the surface heat transfer on the leeward side of the Space Shuttle, taking into account different free stream Reynolds numbers and angles of attack. Another investigation was concerned with the peak heating due to boundary layer transition and flow separation in the case of different Space Shuttle configurations. Criteria for vortex generation on the leeward flow were also examined along with the effect of transition on vortex generation. Attention was given to the leeward flowfield in the vortex flow region and the method of constructing an equivalent model for leeward flowfield analysis.

Zakkay, V.↗

NASA NTRS1981

Subsonic balance and pressure investigation of a 60-deg delta wing with leading-edge devices (data report)

The drag reduction potential of leading edge devices on a 60 degree delta wing at high lift was examined. Geometric variations of fences, chordwise slots, pylon type vortex generators, leading edge vortex flaps, and sharp leading edge extensions were tested individually and in specific combinations to improve high-alpha drag performance with a minimum of low-alpha drag penalty. The force, moment, and surface static pressure data for angles of attack up to 23 degrees, at Mach and Reynolds numbers of 0.16 and 3.85 x 10 to the 6th power per meter are documented.

Rao, D. M.↗

NASA NTRS2004

The Performance of a Subsonic Diffuser Designed for High Speed Turbojet-Propelled Flight

An initial-phase subsonic diffuser has been designed for the turbojet flowpath of the hypersonic x43B flight demonstrator vehicle. The diffuser fit into a proposed mixed-compression supersonic inlet system and featured a cross-sectional shape transitioning flowpath (high aspect ratio rectangular throat-to-circular engine face) and a centerline offset. This subsonic diffuser has been fabricated and tested at the W1B internal flow facility at NASA Glenn Research Center. At an operating throat Mach number of 0.79, baseline Pitot pressure recovery was found to be just under 0.9, and DH distortion intensity was about 0.4 percent. The diffuser internal flow stagnated, but did not separate on the offset surface of this initial-phase subsonic diffuser. Small improvements in recovery (+0.4 percent) and DH distortion (-32 percent) were obtained from using vane vortex generator flow control applied just downstream of the diffuser throat. The optimum vortex generator array patterns produced inflow boundary layer divergence (local downwash) on the offset surface centerline of the diffuser, and an inflow boundary layer convergence (local upwash) on the centerline of the opposite surface.

Biesiadny, Thomas J.↗

NASA NTRS1987

Interaction of an oscillating vortex with a turbulent boundary layer

The effects on mean flow and turbulence caused by meander of a vortex embedded in a two-dimensional boundary layer were investigated experimentally by driving a forced lateral oscillation of the vortex generator. Upstream, the vorticity contours without forcing were found to be round. The forced vortex generator oscillation caused a flattening of the time-averaged vorticity contours and changes in some of the Reynolds stresses. The results indicate that the unforced vortex did not meander significantly upstream, and that the effects of meander can be understood qualitatively from production of Reynolds stresses by the forced motion acting with the exiting three-dimensional velocity field. Farther downstream, the observed differences in the mean vorticity and Reynolds stresses caused by forcing were smaller, mainly because the vortex was substantially diffused at this station, resulting in smaller mean velocity gradients.

Westphal, Russell V.↗

NASA NTRS1975

Exploratory flight investigation of aircraft response to the wing vortex wake generated by the augmentor wing jet STOL research aircraft

A brief exploratory flight program was conducted at Ames Research Center to investigate the vortex wake hazard of a powered-lift STOL aircraft. The study was made by flying an instrumented Cessna 210 aircraft into the wake of the augmentor wing jet STOL research aircraft at separation distances from 1 to 4 n.mi. Characteristics of the wake were evaluated in terms of the magnitude of the upset of the probing aircraft. Results indicated that within 1 n.mi. separation the wake could cause rolling moments in excess of roll control power and yawing moments equivalent to rudder control power of the probe aircraft. Subjective evaluations by the pilots of the Cessna 210 aircraft, supported by response measurements, indicated that the upset caused by the wake of the STOL aircraft was comparable to that of a DC-9 in the landing configuration.

Jacobsen, R. A.↗

NASA NTRS1975

Design and testing of new center inlet and S-duct for B-727 airplane with refanned JT8D engines

The work described in this paper was part of the NASA refan program. The airflow requirement of the refanned JT8D (-100 series) engine increased about 50% above that of the basic JT8D. This required a redesign of the center inlet and S-duct of the Boeing 727 airplane. The paper describes the design constraints for the S-duct and the analytic method used to define the lines of the new duct. Model tests that were conducted at static, angle-of-attack, and crosswind conditions are described with a variety of flow control devices. Test results showed that the new inlet and S-duct have a pressure recovery comparable to that of the existing inlet. By employing corotating vortex generators, less flow distortion was obtained for the core region than the existing duct has with its counter rotating vortex generators.

Ting, C. T.↗

NASA NTRS1972

Exploratory flight investigation of aircraft response to the wing vortex wake generated by jet transport aircraft

The effect of intercepting wing tip vortices generated by large jet transports, including jumbo jets, over separation distances from 1 nautical mile to 15 nautical miles is evaluated on the basis of the response of a vortex probe airplane in the roil mode. The vortex probe test aircraft included a representative general aviation airplane, an executive jet, a fighter, and light and medium weight jet transports. The test conditions and airplane configurations were comparable to those normally used during takeoff, landing, or holding pattern operations. For flight safety the tests were performed at altitudes from 9500 feet to 12,500 feet. In addition to an evaluation of the probe airplane response, a flight test technique is suggested for determining minimum separation distance, using as variable the ratio of vortex-induced roll acceleration to maximum lateral control acceleration and the gross weight of the generating aircraft.

Andrews, W. H.↗

NASA NTRS2015

Influences of Models on the Unsteady Pressure Characteristics of the NASA National Transonic Facility

Pressure fluctuations have been measured over the course of several tests in the National Transonic Facility to study unsteady phenomenon both with and without the influence of a model. Broadband spectral analysis will be used to characterize the length scales of the tunnel. Special attention will be given to the large-scale, low frequency data that influences the Mach number and force and moment variability. This paper will also discuss the significance of the vorticity and sound fields that can be related to the Common Research Model and will also highlight the comparisons to an empty tunnel configuration. The effectiveness of vortex generators placed at the interface of the test section and wind tunnel diffuser showed promise in reducing the empty tunnel unsteadiness, however, the vortex generators were ineffective in the presence of a model.

Jones, Gregory↗

NASA NTRS1984

Application of panel method to wake vortex/wing interaction and comparison with experiment

The ability of a low-order panel method to calculate the aerodynamic loads on wings caused by interaction with wake vortices was studied. The loads were calculated for various positions of a downstream following wing relative to an upstream vortex-generating wing. Calculated vortex-induced span loads and rolling-moment coefficients on the following wing were compared with experimental data. A good agreement with experiment was obtained when the following wing was located more than one following-wing chord length from the tip vortex. The predictions deteriorated as the following wing was placed closer to the vortex. At large downstream distances (approximately 10 generating-wing chord lengths), induced rolling-moment coefficients on the following wing were consistently overestimated. Despite the strong interaction between the wake-vortex filaments and surface doublet panels, the accuracy of the calculations was in most cases independent of the panel distribution and density. A good agreement between theoretical and experimental loads was obtained with a minimum of experimentation with panel arrangements.

Smith, B. E.↗

NASA NTRS2001

Compressor Flow Control Concepts: UEET Compressor Flow Control Modeling - 2

Several passive flow control devices have been modeled computationally in the Swift CFD code. The models were applied to the first stage rotor and stator of the baseline UEET compressor in an attempt to improve efficiency and/or stall margin. The devices included suction surface bleed, tip injection, self-aspirated rotors, area-ruled casing, and vortex generators. The models and computed results will be described in the presentation. None of the results have shown significant gains in efficiency; however, casing vortex generators have shown potential improvements in stall margin.

Chima, Rodrick V.↗

NASA NTRS1991

Three-dimensional analysis of the Pratt and Whitney alternate design SSME fuel turbine

The three dimensional viscous time-mean flow in the Pratt and Whitney alternate design space shuttle main engine fuel turbine is simulated using the average passage Navier-Stokes equations. The migration of secondary flows generated by upstream blade rows and their effect on the performance of downstream blade rows is studied. The present simulation confirms that the flow in this two stage turbine is highly three dimensional and dominated by the tip leakage flow. The tip leakage vortex generated by the first blade persists through the second blade and adversely affects its performance. The greatest mixing of the inlet total temperature distortion occurs in the second vane and is due to the large leakage vortex generated by the upstream rotor. It is assumed that the predominant spanwise mixing mechanism in this low aspect ratio turbine is the radial transport due to the deterministically unsteady vortical flow generated by upstream blade rows. A by-product of the analysis is accurate pressure and heat loads for all blade rows under the influence of neighboring blade rows. These aero loads are useful for advanced structural analysis of the vanes and blades.

Kirtley, K. R.↗

NASA NTRS1994

Axis switching and spreading of an asymmetric jet: Role of vorticity dynamics

The effects of vortex generators and periodic excitation on vorticity dynamics and the phenomenon of axis switching in a free asymmetric jet are studied experimentally. Most of the data reported are for a 3:1 rectangular jet at a Reynolds number of 450,000 and a Mach number of 0.31. The vortex generators are in the form of 'delta tabs', triangular shaped protrusions into the flow, placed at the nozzle exit. With suitable placement of the tabs, axis switching could be either stopped or augmented. Two mechanisms are identified governing the phenomenon. One, as described by previous researchers and referred to here as the omega(sub theta)-induced dynamics, is due to difference in induced velocities for different segments of a rolled up azimuthal vortical structure. The other, omega(sub x)-induced dynamics, is due to the induced velocities of streamwise vortex pairs in the flow. Both dynamics can be active in a natural asymmetric jet; the tendency for axis switching caused by the omega(sub theta)-induced dynamics may be, depending on the streamwise vorticity distribution, either resisted or enhanced by the omega(sub x)-induced dynamics. While this simple framework qualitatively explains the various observations made on axis switching, mechanisms actually in play may be much more complex. The two dynamics are not independent as the flow field is replete with both azimuthal and streamwise vortical structures which continually interact. Phase averaged flow field data for a periodically forced case, over a volume of the flow field, are presented and discussed in an effort to gain insight into the dynamics of these vortical structures.

Zaman, K. B. M. Q.↗

NASA NTRS1972

Dynamic flow angle measurements at the diffuser exit of a Mach 2.5 mixed compression inlet

An exploratory investigation was made to determine the magnitude of the dynamic flow angle at a single point in the diffuser exit of a Mach 2.50 inlet. Results indicate that the maximum flow angle variation was + or - 3 degrees except when vortex generators were installed in the subsonic diffuser. The amplitude of these flow angle fluctuations was directly related to the amplitude of the total pressure fluctuations at the probe survey point. Flow angle fluctuations as high as + or - 11 degrees were recorded when vortex generators were installed near the probe survey point.

Prati, W. M.↗

NASA NTRS2002

Flow Control Device Evaluation for an Internal Flow with an Adverse Pressure Gradient

The effectiveness of several active and passive devices to control flow in an adverse pressure gradient with secondary flows present was evaluated in the 15 Inch Low Speed Tunnel at NASA Langley Research Center. In this study, passive micro vortex generators, micro bumps, and piezoelectric synthetic jets were evaluated for their flow control characteristics using surface static pressures, flow visualization, and 3D Stereo Digital Particle Image Velocimetry. Data also were acquired for synthetic jet actuators in a zero flow environment. It was found that the micro vortex generator is very effective in controlling the flow environment for an adverse pressure gradient, even in the presence of secondary vortical flow. The mechanism by which the control is effected is a re-energization of the boundary layer through flow mixing. The piezoelectric synthetic jet actuators must have sufficient velocity output to produce strong longitudinal vortices if they are to be effective for flow control. The output of these devices in a laboratory or zero flow environment will be different than the output in a flow environment. In this investigation, the output was higher in the flow environment, but the stroke cycle in the flow did not indicate a positive inflow into the synthetic jet.

Jenkins, Luther N.↗

NASA NTRS2005

Vortex Rings Generated by a Shrouded Hartmann-Sprenger Tube

The pulsed flow emitted from a shrouded Hartmann-Sprenger tube was sampled with high-frequency pressure transducers and with laser particle imaging velocimetry, and found to consist of a train of vortices. Thrust and mass flow were also monitored using a thrust plate and orifice, respectively. The tube and shroud lengths were altered to give four different operating frequencies. From the data, the radius, velocity, and circulation of the vortex rings was obtained. Each frequency corresponded to a different length to diameter ratio of the pulse of air leaving the driver shroud. Two of the frequencies had length to diameter ratios below the formation number, and two above. The formation number is the value of length to diameter ratio below which the pulse converts to a vortex ring only, and above which the pulse becomes a vortex ring plus a trailing jet. A modified version of the slug model of vortex ring formation was used to compare the observations with calculated values. Because the flow exit area is an annulus, vorticity is shed at both the inner and outer edge of the jet. This results in a reduced circulation compared with the value calculated from slug theory accounting only for the outer edge. If the value of circulation obtained from laser particle imaging velocimetry is used in the slug model calculation of vortex ring velocity, the agreement is quite good. The vortex ring radius, which does not depend on the circulation, agrees well with predictions from the slug model.

DeLoof, Richard L.↗

NASA NTRS1992

Application of computational fluid dynamics to the study of vortex flow control for the management of inlet distortion

A study is presented to demonstrate that the Reduced Navier-Stokes code RNS3D can be employed effectively to develop a vortex generator installation that minimizes engine face circumferential distortion by controlling the development of secondary flow. The necessary computing times are small enough to show that similar studies are feasible within an analysis-design environment with all its constraints of costs and time. This study establishes the nature of the performance enhancements that can be realized with vortex flow control, and indicates a set of aerodynamic properties that can be utilized to arrive at a successful vortex generator installation design.

Anderson, Bernhard H.↗