Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “voltage acceleration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

3D Monte Carlo simulation of backscattered electron signal variation across pore-solid boundaries in cement-based materials

Three-dimensional (3D) Monte Carlo simulation was used to study the variation of backscattered electron (BSE) signal across pore-solid boundaries in cement-based materials in order to enhance quantitative analysis of pore structure. The effects of pore size, depth and boundary inclination angle were investigated. It is found that pores down to 1 nm can generate sufficient contrast to be detected. Visibility improves with larger pore size, smaller beam probe size and lower acceleration voltage. However, pixels in shallow pores or near pore boundaries display higher grey values (brightness) than expected due to sampling sub-surface or neighbouring solid material. Thus, cement-based materials may appear less porous or the pores appear smaller than they actually are in BSE images. Simulated BSE images were used to test the accuracy of the Overflow pore segmentation method. Results show the method is generally valid and gives low errors for pores that are 1 μm and greater.

36 MATERIALS SCIENCE↗

Next-generation anion exchange membrane water electrolyzers operating for commercially relevant lifetimes

Alkaline anion exchange membrane (AEM) water electrolysis has gained increasing attention due to its potential to achieve low-cost, high performance hydrogen production. However, most existing membranes are not durable in industrial settings. In this work, we demonstrate good performance relative to industrial parameters using Sustainion® anion exchange membranes. Long-duration tests showed stable performance of 1 A/cm 2 at 1.85 V with a degradation rate of less than 1 μV/h over 10,000 h. The projected lifetime is thus over 20 years. Daily on/off cycling performance over the course of 30 years was simulated experimentally through accelerated voltage shock tests, resulting in a performance loss of only 0.15 μV/cycle over 11,000 cycles. As shown through impact and crossover testing, an improvement in performance is achieved by the addition of zirconia to the polymer matrix and mechanically reinforcing the membrane.

08 HYDROGEN↗

Non-destructive characterisation of polymers and Al-alloys by polychromatic cone-beam phase contrast tomography

X-ray computed tomography (XCT) has become a very important tool for the non-destructive characterisation of materials. Continuous improvements in the quality and performance of X-ray tubes and detectors have led to cone-beam XCT systems that can now achieve spatial resolutions down to 1 {mu}m and even below. Since not only the amplitude but also the phase of an X-ray beam is altered while passing through an object, phase contrast effects can occur even for polychromatic sources when the spatial coherence due to a small focal spot size is high enough. This can lead to significant improvements over conventional attenuation-based X-ray computed tomography. Phase contrast can increase by edge enhancement the visibility of small structures and of features which are only slightly different in attenuation. We report on the possibilities of polychromatic cone-beam phase contrast tomography for non-destructive characterisation of materials. A carbon fibre-reinforced polymer and the Al-alloys AlMg5Si7 and AlSi18 were investigated with high resolution cone-beam X-ray computed tomography with a polychromatic tube source. Under certain conditions strong phase contrast resulting in an upward and downward overshooting of the grey values across edges was observed. The phase effects are much stronger for the polymer than for the Al-alloys. The influence on the phase contrast of the parameters, including source-detector distance, focal spot size and tube acceleration voltage is presented. Maximum phase contrast was observed for a maximum distance between the source and the detector, for a low voltage and a minimum focal spot size at the X-ray source. The detectability of the different phases is improved by the edge enhancement and the resulting improvement of sharpness. Thus, a better segmentation of the carbon fibres in the fibre-reinforced polymer and of the Mg{sub 2}Si-phase in the AlMg5Si7-alloy is achieved. Primary and eutectic Si cannot be detected by attenuation-based X-ray computed tomography due to the small difference in X-ray attenuation between the Si and the Al-matrix in AlSi18. However, phase contrast effects lead to a significant detectability and the large primary Si particles become clearly visible in the tomograms of AlSi18. - Highlights: Black-Right-Pointing-Pointer Phase contrast increases with increasing distance object-detector and with decreasing U, X-ray spot. Black-Right-Pointing-Pointer The detectability of details is improved by the phase contrast. Black-Right-Pointing-Pointer For the carbon fibre-reinforced polymer the visibility of the carbon fibres is improved. Black-Right-Pointing-Pointer For AlMg5Si7 the detectability of the phases Fe-aluminides and Mg{sub 2}Si particles is improved. Black-Right-Pointing-Pointer For AlSi18 primary Si particles with a size > 50 {mu}m become detectable because of the phase contrast.

36 MATERIALS SCIENCE↗

Microstructural development of electron beam processed Al-3Ti-1Sc alloy under different electron beam scanning speeds

A systematic study has been made of the microstructural development in as-cast 30 mm thick Al-3Ti-1Sc (wt%) plate samples that were processed by electron beam (EB) melting at different scanning speeds of 3, 5, 8, 12, 15 and 20 mm/s. The composition of the alloy is designed to capitalize on the potential for significantly extended solubility values of both Sc and Ti in Al when cooled at high cooling rates. The resulting microstructures are characterised using transmission electron microscopy (TEM) and other analytical means, assisted with Thermo-Calc predictions and Vicker's microhardness measurements. EB scanning speed plays a key role in determining the phase formation and microstructural development in the Al-3Ti-1Sc alloy when the beam is applied an accelerating voltage of 50 kV and a current of 30 μA. The major microstructural features in the re-solidified zone include (i) the formation of the primary tetragonal Al{sub 3}(Ti,Sc) phases and their retention or subsequent transformation to stable cubic Al{sub 3}(Ti,Sc) phases; (ii) the complete suppression of the primary tetragonal Al{sub 3}(Ti,Sc) phases at the scanning speed of 20 mm/s; and (iii) the formation of cubic Al{sub 3}(Ti,Sc) precipitates in the α(Al) matrix supersaturated with both Sc and Ti. These experimental findings are informative for both EB processing of Al-Ti-Sc alloys and the design of new Al alloys for additive manufacturing processes.

36 MATERIALS SCIENCE↗

Effect of electron irradiation on nanogroove-networked single-crystalline and dendritic polycrystalline platinum nanosheets prepared from lyotropic surfactant liquid-crystal templates

Using transmission electron microscopy (TEM) electron irradiation effects were studied for nanogroove-network structured single-crystalline and dendritic polycrystalline Pt nanosheets 50-60 nm in size. These two nanosheets with nearly the same average groove-width or dendritic spacing of 1.3-1.4 nm were prepared from the mixed and single surfactant liquid crystalline templates, respectively. On exposure to electron beam for 20 min at the acceleration voltage of 200 kV, the nanogrooved nanosheets were morphologically little affected, but the dendritic ones were transformed into less branched polycrystalline structures with spacings distributed around {approx}1.7 nm. The shape transformation of the latter occurred by the combined mechanism of segmental migration and atomic diffusion. These observations indicate that the nanogrooved Pt nanosheets are highly stabilized by the grooved but crystallographically continuous Pt framework, leading to their extremely high thermo-resistance, in marked contrast to the polycrystalline dendritic structures constructed of crystallographically discontinuous linkages of nanoblocks.

36 MATERIALS SCIENCE↗

Energy dependence on formation of TiO{sub 2} nanofilms by Ti ion implantation and annealing

Graphical abstract: - Highlights: • Fabrication of TiO{sub 2} films by ion implantation and annealing strongly depends on ion energy. • Best photocatalytic activity is achieved in the TiO{sub 2} nanofilm annealed at 1000 °C. • Phase transformation of TiO{sub 2} appears under annealing temperature of 900 °C. - Abstract: TiO{sub 2} nanofilms were fabricated by a solid-phase-growth progress. The silica glass slides were implanted with Ti ions to the fluence of 1.84 × 10{sup 17} ions/cm{sup 2} at accelerate voltages of 20, 50, and 80 kV, respectively. The samples were annealed in oxygen atmosphere at 700, 800, 900, and 1000 °C for 4 h, respectively. The influence of the ion energy and the annealing temperature on the formation and phase transformation of the TiO{sub 2} films was studied. It was found that anatase TiO{sub 2} nanofilms instead of embedded rutile TiO{sub 2} nanoparticles on the substrate surfaces when the energy of implanted Ti atoms was 20 kV.

36 MATERIALS SCIENCE↗

Red phosphor Ca{sub 2}Ge{sub 7}O{sub 16}:Eu{sup 3+} for potential application in field emission displays and white light-emitting diodes

Abstract: A novel red emitting phosphor of Eu{sup 3+} doped Ca{sub 2}Ge{sub 7}O{sub 16} was prepared through the solid state reaction. The luminescence properties were studied in detail by photoluminescence excitation (PLE), emission (PL) spectra and cathodoluminescence (CL). Under the excitation of ultraviolet light, Ca{sub 2}Ge{sub 7}O{sub 16}:Eu{sup 3+} phosphor shows the characteristic {sup 5}D{sub 0}-{sup 7}F{sub J}(J = 1, 2, 3, 4) transition of Eu{sup 3+} with two different emissions due to the two kinds of Eu{sup 3+} ions. The luminescent intensity could be improved by co-doping with the charge compensators R{sup +} (Li, Na, K) which partially substitute for Ca{sup 2+} crystal sites. CL spectra show that Eu{sup 3+} ions were excited by the plasma produced by the incident electrons and the CL properties of Ca{sub 2}Ge{sub 7}O{sub 16}:Eu{sup 3+}, Li{sup +} as a function of accelerating voltage and probe current were investigated. Ca{sub 2}Ge{sub 7}O{sub 16}:Eu{sup 3+} phosphor offers higher thermal stability compared with the commercial red phosphor Y{sub 2}O{sub 3}:Eu{sup 3+}. The results indicate that Ca{sub 2}Ge{sub 7}O{sub 16}:Eu{sup 3+} can be a suitable red-emitting phosphor candidate for FEDs and w-LEDs.

36 MATERIALS SCIENCE↗

Quantitative comparison of bright field and annular bright field imaging modes for characterization of oxygen octahedral tilts

Octahedral tilt behavior is increasingly recognized as an important contributing factor to the physical behavior of perovskite oxide materials and especially their interfaces, necessitating the development of high-resolution methods of tilt mapping. There are currently two major approaches for quantitative imaging of tilts in scanning transmission electron microscopy (STEM), bright field (BF) and annular bright field (ABF). In this study, we show that BF STEM can be reliably used for measurements of oxygen octahedral tilts. While optimal conditions for BF imaging are more restricted with respect to sample thickness and defocus, we find that BF imaging with an aberration-corrected microscope with the accelerating voltage of 300 kV gives us the most accurate quantitative measurement of the oxygen column positions. Using the tilted perovskite structure of BiFeO 3 (BFO) as our test sample, we simulate BF and ABF images in a wide range of conditions, identifying the optimal imaging conditions for each mode. Finally, we show that unlike ABF imaging, BF imaging remains directly quantitatively interpretable for a wide range of the specimen mistilt, suggesting that it should be preferable to the ABF STEM imaging for quantitative structure determination.

36 MATERIALS SCIENCE↗

High-Resolution Field Emission Scanning Electron Microscopy (FESEM) Imaging of Cellulose Microfibril Organization in Plant Primary Cell Walls

Abstract We have used field emission scanning electron microscopy (FESEM) to study the high-resolution organization of cellulose microfibrils in onion epidermal cell walls. We frequently found that conventional “rule of thumb” conditions for imaging of biological samples did not yield high-resolution images of cellulose organization and often resulted in artifacts or distortions of cell wall structure. Here we detail our method of one-step fixation and dehydration with 100% ethanol, followed by critical point drying, ultrathin iridium (Ir) sputter coating (3 s), and FESEM imaging at a moderate accelerating voltage (10 kV) with an In-lens detector. We compare results obtained with our improved protocol with images obtained with samples processed by conventional aldehyde fixation, graded dehydration, sputter coating with Au, Au/Pd, or carbon, and low-voltage FESEM imaging. The results demonstrated that our protocol is simpler, causes little artifact, and is more suitable for high-resolution imaging of cell wall cellulose microfibrils whereas such imaging is very challenging by conventional methods.

biofuels (including algae and biomass), bio-inspir↗

Intrinsic Li Distribution in Layered Transition-Metal Oxides Using Low-Dose Scanning Transmission Electron Microscopy and Spectroscopy

Understanding Li distribution in layered lithium transition-metal oxide (LiTMO) cathodes in Li-ion batteries has been a major challenge at the atomic scale and nanoscale. Li is extremely difficult to study by transmission electron microscopy (TEM) because the high-energy electrons impart significant energy and cause massive migration. Here, we directly map the intrinsic spatial distribution and bonding of Li in LiNiO 2 -layered cathode materials using low-dose and low-loss electron energy loss spectroscopy (EELS). EELS spectra of the Li–K edge are measured simultaneously with O–K and Ni–L, M 3,2 edges from layered, cation-mixed, and rock-salt phases and directly matched with atomic-resolution scanning TEM images to correlate the changes in peak intensities and positions to the stoichiometry changes with continual loss of Li and O. Changes in the Li content in the LiNiO 2 particles as a function of electron beam dose are studied by sequential Li spectroscopic mapping. We show that the “intrinsic” Li distribution can be observed using a total dose of less than ~1.5 × 10 8 e – nm –2 at an accelerating voltage of 80 kV. The method of nanoscale mapping of Li distribution introduced in this study is applicable to high-Ni LiTMO cathode materials (>89% of Ni) as well as LiNiO 2 . Further study on the extra peaks of the Li–K edge reveals that the peak at ~59 eV is from the Li ions intercalated in between NiO 2 layers barely interacting with each other with less Li K shell electrons pulled to the L shell electrons in NiO 2 . Furthermore, the results shown here provide improved low-loss TEM characterization approaches that can be used to understand the intrinsic fundamental behaviors in Li-ion batteries.

25 ENERGY STORAGE↗

Quantitative Specifications to Avoid Degradation during E-Beam and Induced Current Microscopy of Halide Perovskite Devices

Degradation due to electron beam exposure has posed a challenge in the use of electron microscopy to probe halide perovskite materials and devices. Herein, the interaction between the electron beam and the perovskite across acceleration voltages and at low probe currents is investigated in a scanning electron microscope (SEM) by monitoring the electron-beaminduced current (EBIC) response in perovskite solar cells in a planview configuration. SEM probe conditions are identified where dozens of repeated scans over a single region of the perovskite solar cell induce minimal electronic degradation. Overall, the induced current response of the perovskite device is found to strongly depend upon the beam condition: rapid decay occurs at high beam powers, the current activates at the lowest beam powers, and a newfound quasi-steady response is revealed at intermediate beam conditions. A quantitative window for the successful conduction of e-beam studies with minimal electronic degradation is revealed by evaluating induced current response over a wide range of perovskite devices, which invites broader use of SEM-based characterization techniques, including EBIC, as powerful techniques for correlative microscopy investigations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Atomic Structure and Dynamics of Single Platinum Atom Interactions with Monolayer MoS 2

In this work, we have studied atomic level interactions between single Pt atoms and the surface of monolayer MoS 2 using aberration-corrected annular dark field scanning transmission electron microscopy at an accelerating voltage of 60 kV. Strong contrast from single Pt atoms on the atomically resolved monolayer MoS 2 lattice enables their exact position to be determined with respect to the MoS2 lattice, revealing stable binding sites. In regions of MoS 2 free from surface contamination, the Pt atoms are localized in S vacancy sites and exhibit dynamic hopping to nearby vacancy sites driven by the energy supplied by the electron beam. However, in areas of MoS 2 contaminated with carbon surface layers, the Pt atoms appear at various positions with respect to the underlying MoS 2 lattice, including on top of Mo and in off-axis positions. These variations are due to the Pt bonding with the surrounding amorphous carbon layer, which disrupts the intrinsic Pt–MoS 2 interactions, leading to more varied positions. Density functional theory (DFT) calculations reveal that Pt atoms on the surface of MoS 2 have a small barrier for migration and are stabilized when bound to either a single or double sulfur vacancies. DFT calculations have been used to understand how the catalytic activity of the MoS 2 basal plane for hydrogen evolution reaction is influenced by Pt dopants by variation of the hydrogen adsorption free energy. Finally, this strong dependence of catalytic effect on interfacial configurations is shown to be common for a series of dopants, which may provide a means to create and optimize reaction centers.

2D materials↗

Generalizable Image Segmentation for Microstructure Characterization Through Integrated SEM and EBSD Analysis

We demonstrate generalizable semantic segmentation using minimal ground truth data. Correlated scanning electron microscopy (SEM) images and electron backscatter diffraction (EBSD) measurements of frictionstir processed 316L stainless steel plates were used to train deep learning models for grain boundary segmentation. Secondary electron (SE) imaging taken at an accelerating voltage of 10 keV correlated to EBSD-derived grain boundaries produced the best performing model. Notably, an ensemble of three models trained on a single SE image produced accurate segmentation over a series of BSE images of samples manufactured under different processing parameters, with a resultant mean absolute error in grain size of 0.34 µm. The striking generalizability of the models likely results from the similar escape depths of the SE training input and the EBSD training output and the reduced probability of dislocation artifacts appearing in the image. This finding highlights the importance of considering the physical principles behind imaging in the development of robust segmentation models for microstructure characterization.

Taufique, Mohammad Fuad Nur↗

Factors influencing quantitative liquid (scanning) transmission electron microscopy

One of the experimental challenges in the study of nanomaterials in liquids in the (scanning) transmission electron microscope ((S)TEM) is gaining quantitative information. A successful experiment in the fluid stage will depend upon the ability to plan for sensitive factors such as the electron dose applied, imaging mode, acceleration voltage, beam-induced solution chemistry changes, and the specifics of solution reactivity. In this paper, we make use of a visual approach to show the extent of damage of different instrumental and experimental factors in liquid samples imaged in the (S)TEM. Previous results as well as new insights are presented to create an overview of beam-sample interactions identified for changing imaging and experimental conditions. This work establishes procedures to understand the effect of the electron beam on a solution, provides information to allow for a deliberate choice of the optimal experimental conditions to enable quantification, and identifies the experimental factors that require further analysis for achieving fully quantitative results in the liquid (S)TEM.

(S)TEM↗

Charging-driven coarsening and melting of a colloidal nanoparticle monolayer at an ionic liquid–vacuum interface

In this work, we induce and investigate the coarsening and melting dynamics of an initially static nanoparticle colloidal monolayer at an ionic liquid–vacuum interface, driven by a focused, scanning electron beam. Coarsening occurs through grain interface migration and larger-scale motions such as grain rotations, often facilitated by sliding dislocations. The progressive decrease in area fraction that drives melting of the monolayer is explained using an electrowetting model whereby particles at the interface are solvated once their accumulating charge recruits sufficient counterions to subsume the particle. Subject to stochastic particle removal from the monolayer, melting is recapitulated in simulations with a Lennard-Jones potential. This new driving mechanism for colloidal systems, whose dynamical timescales we show can be controlled with the accelerating voltage, opens the possibility to manipulate particle interactions dynamically without need to vary particle intrinsic properties or surface treatments. Furthermore, the decrease in particle size availed by electron imaging presents opportunities to observe force and time scales in a lesser-explored regime intermediate between typical colloidal and molecular systems.

36 MATERIALS SCIENCE↗

Field-emission-type x-ray source using carbon-nanofibers

An x-ray irradiation system of field-emission type has been constructed using carbon-nanofibers (CNFs) grown on a palladium wire that is 50 {mu}m in diameter. The electron current emitted from the CNFs was approximately 1 mA and was stable within 10% for a long time t>5000 h. The electrons passing through a slit in the gate electrode were accelerated to the desired energy, and were made to impinge on the metal target (Ti, Cu, Mo, and W) for generating x rays. The x-rays transmitted through Be-window were characterized using energy analyzers and a dosimeter. At an acceleration voltage of V{sub a}=50 kV, the energy spectra of the x-rays were exclusively composed of characteristic signals except for the Mo-target, and the dose rates of x-rays were D=2.5-14 Gy/min, depending on the target metals. This system also provides sharp x-ray images of both biological and nonbiological materials.

36 MATERIALS SCIENCE↗

Quadrupole mass spectrometry and time-of-flight analysis of ions resulting from 532 nm pulsed laser ablation of Ni, Al, and ZnO targets

This work describes the design and validation of an instrument to measure the kinetic energies of ions ejected by the pulsed laser ablation (PLA) of a solid target. Mass spectra show that the PLA of Ni, Al, and ZnO targets, in vacuum, using the second harmonic of a Nd:YAG laser (532 nm, pulse duration {approx}10 ns) generates abundant X{sup n+} ions (n{<=}3 for Ni, {<=}2 for Al, {<=}3 and {<=}2 for Zn and O respectively from ZnO). Ions are selected by their mass/charge (m/z) ratio prior to the determination of their times of flight. PLA of Ni has been studied in most detail. The mean velocities of ablated Ni{sup n+} ions are shown to follow the trend v(Ni{sup 3+})>v(Ni{sup 2+})>v(Ni{sup +}). Data from Ni{sup 2+} and Ni{sup 3+} are fitted to shifted Maxwellian functions and agree well with a model which assumes both thermal and Coulombic contributions to ion velocities. The dependence of ion velocities on laser pulse energy (and fluence) is investigated, and the high energy data are shown to be consistent with an effective accelerating voltage of {approx}90 V within the plume. The distribution of velocities associated with Ni{sup 3+} indicates a population at cooler temperature than Ni{sup 2+}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A critical literature review of focused electron beam induced deposition

An extensive review is given of the results from literature on electron beam induced deposition. Electron beam induced deposition is a complex process, where many and often mutually dependent factors are involved. The process has been studied by many over many years in many different experimental setups, so it is not surprising that there is a great variety of experimental results. To come to a better understanding of the process, it is important to see to which extent the experimental results are consistent with each other and with the existing model. All results from literature were categorized by sorting the data according to the specific parameter that was varied (current density, acceleration voltage, scan patterns, etc.). Each of these parameters can have an effect on the final deposit properties, such as the physical dimensions, the composition, the morphology, or the conductivity. For each parameter-property combination, the available data are discussed and (as far as possible) interpreted. By combining models for electron scattering in a solid, two different growth regimes, and electron beam induced heating, the majority of the experimental results were explained qualitatively. This indicates that the physical processes are well understood, although quantitatively speaking the models can still be improved. The review makes clear that several major issues remain. One issue encountered when interpreting results from literature is the lack of data. Often, important parameters (such as the local precursor pressure) are not reported, which can complicate interpretation of the results. Another issue is the fact that the cross section for electron induced dissociation is unknown. In a number of cases, a correlation between the vertical growth rate and the secondary electron yield was found, which suggests that the secondary electrons dominate the dissociation rather than the primary electrons. Conclusive evidence for this hypothesis has not been found. Finally, there is a limited understanding of the mechanism of electron induced precursor dissociation. In many cases, the deposit composition is not directly dependent on the stoichiometric composition of the precursor and the electron induced decomposition paths can be very different from those expected from calculations or thermal decomposition. The dissociation mechanism is one of the key factors determining the purity of the deposits and a better understanding of this process will help develop electron beam induced deposition into a viable nanofabrication technique00.

36 MATERIALS SCIENCE↗