Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thin membrane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Multiport high-pressure synchrotron x-ray microscopy cell (CRADA Final Report)

The LBNL team developed a multiport cell allowing for fluid flow, with electrical contacts for sample bias, and with reference electrodes. The cell is currently installed and operating in beam-line 11.0.2 of the ALS, the Berkeley Synchrotron. The cell is closed by a membrane consisting of several stacked layers of graphene (1 to 3). The graphene membrane is supported on a 100 nm thick Si3N4 membrane covered with a 20 nm thin gold film for improved adhesion of the graphene and to ensure electrical conductivity. The Si3N4 film is perforated with a periodic array of holes 1 to 2 micrometers diameter. The cell can withhold an internal pressure (gas or liquid) of up to 10 atmospheres for in situ/operando studies using X-ray Photoelectron emission (XPS), and X-ray Absorption Spectroscopy (XAS). It is also ideal for tip-enhanced nano-Infrared Spectroscopy studies of molecules at the interface between the graphene and the liquid or gas filling the cell. Materials studied in the LBNL laboratory are in the form of nanoparticles, or thin films (few nm) deposited on the side of the graphene membrane facing the solution or gas inside the cell.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A Relief Zone Architecture for Enhanced Durability of Ultrathin Membranes in Electrochemical Conversion Devices

Premature cell failures in electrochemical conversion systems often result when membrane electrode assemblies (MEAs) are prepared with ultra-thin (= 15 micrometer-thick) polymer electrolyte membranes (PEMs). These high-performance PEMs are susceptible to mechanical degradation from stress concentrations arising from component and device-level integration. Herein, a relief zone was developed to mitigate mechanical degradation by alleviating excess and non-uniform compression across the active area. Relief zones, created through the ablation of carbonaceous diffusion material achieves a seamless adaptation across a range of MEA dimensions and electrochemical applications without need for costly hardware modifications. This concept was demonstrated using fuel cells as a case study. Accelerated stress test (AST) validations yielded a 6-fold improvement for MEAs prepared with relief zones (i.e., lifetime approximately 1500 h) compared to those fabricated using conventional edge-protection techniques, showcasing the utility of this technique in decoupling integration and device-level engineering effects from intrinsic material limitations for durable electrochemical devices.

14 SOLAR ENERGY↗
DOE OSTI2025

FCET Solid Oxide Fuel Cell Testing and Development (CRADA 526) (Final Report)

Pacific Northwest National Laboratory (PNNL) tested electrolyte coatings from Fuel Cell Enabling Technologies, Inc. (FCET) for use in solid oxide fuel cells (SOFCs). The key technology held by FCET is a process to deposit thin layers of oxide materials, less than 1 μm in thickness. The range of possible materials that can be deposited with their method is broad, but this project focused on the gadolinium-doped ceria (GDC) and yttria-stabilized zirconia (YSZ) electrolytes for SOFCs. Thin, gas tight electrolyte membranes have been a long-sought target in SOFC research. The thinner the electrolyte, the lower the cell resistance, and the higher performance of the cell (or the lower the operating temperature). A YSZ thickness of 1 μm would be a step change from the state-of-the-art, tape-cast electrolytes (~10 μm). An in-house prototype SOFC stack from FCET was first tested. The sealing geometry of the prototype stack was determined to be problematic, and testing shifted to button cells. Anode-supported solid oxide electrolysis cell (SOEC) button cells without an electrolyte layer were produced at PNNL and sent to FCET for coating with electrolyte. Three cells were tested with a gadolinium-doped ceria (GDC) electrolyte applied via spin coating. GDC was chosen for its conductivity at lower temperatures than YSZ. All three cells failed during initial reduction under hydrogen at 600°C. Testing then shifted to YSZ, which is the standard SOFC electrolyte. Several button cells were coated with YSZ and examined with scanning electron microscopy (SEM). A promising coating of ~1 mm thickness was observed under SEM. A similarly coated button cell was tested and failed similarly to previous tests during reduction at 600°C. The YSZ coating appeared dense and uniform in SEM analysis. The roughness of the underlying Ni/YSZ anode is on the order of 1 μm, and that may have compromised the gas-tightness of the coating. Further development is warranted to understand and refine the coating process. Thin YSZ applied via this spin-coating technique could be used as a low-cost, drop-in replacement in large-scale SOFC manufacturing processes, improving cell performance and lowering the cost per watt of SOFCs.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Low temperature hydrogen superpermeation in vanadium composite metal foil pumps

Palladium-based foil membranes are an effective option for hydrogen isotope recovery from the plasma exhaust of future fusion plants, but cost and availability are concerns. Vanadium (V) is a relatively low cost, neutron tolerant material with high hydrogen permeability. It has been well-studied as a superpermeable membrane at high temperature (>500 °C), but V displays negligible superpermeation at low temperature (75–200 °C) due to catalytic limitations. Composite membranes were fabricated by depositing thin layers (~100 nm) of either Pd or BCC PdCu on sputter-cleaned vanadium foils (100 μm). Symmetric membranes elevated superpermeation to levels approaching bulk Pd or PdCu foils, with ~5X higher flux in the latter reflecting the superior properties of PdCu. Asymmetric membranes revealed that the Pd-based catalyst layer was critical for both efficient absorption of superthermal hydrogen upstream as well as catalyzing re-combinative desorption downstream. At T ≥ 150 °C composite membrane superpermeation was equivalent to the Pd-based foils, but the flux was attenuated by a factor of 2-3X as the temperature was reduced. This deviation from pure foil performance coincided with the formation of vanadium hydride (β-V 2 H), which also impacted the transient response. Nevertheless, no embrittlement was observed under the conditions examined and elevating the temperature >150 °C removed the hydride and restored full performance. The achievement of palladium-level performance with a >99% reduction in Pd inventory makes these V composite metal foils pumps an attractive option for low temperature hydrogen isotope recovery in future fusion plants.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

In situ formation of polymer-inorganic solid-electrolyte interphase for stable polymeric solid-state lithium-metal batteries

Composite polymer electrolytes (CPEs) for solid-state Li-metal batteries (SSLBs) still suffer from gradually increased interface resistance and unconstrained Li-dendrite growth. Herein, we addressed the challenges by designing a LiF-rich inorganic solid-electrolyte interphase (SEI) through introducing a fluoride-salt-concentrated interlayer on CPE film. The rigid but flexible CPE helps accommodate the volume change of electrodes, while the polymeric highly concentrated electrolyte (PHCE) surface-layer regulates Li-ion flux due to the formation of a stable LiF-rich SEI via anion reduction. The designed CPE-PHCE presents enhanced ionic conductivity and high oxidation stability of >5.0 V (versus Li/Li + ). Furthermore, it dramatically reduces the interfacial resistance and achieves a high critical current density of 4.5 mA cm –2 . The SSLBs, fabricated with thin CPE-PHCE membranes (<100 μm) and Co-free LiNiO 2 cathodes, exhibit exceptional electrochemical performance and long cycling stability. Lastly, this approach of SEI design can also be applied to other types of batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Ion-gated carbon molecular sieve gas separation membranes

Membrane technology lies at the heart of many industrial gas separation processes and applications. Molecular sieving membranes that break the Robeson limit are desirable for energy-efficient gas separation. In this paper, we report a facile strategy of directly integrating ionic liquids (ILs) into porous membranes. Particularly, the ILs form an ultra-thin layer on the carbon molecular sieve (CMS) membranes rather than penetrating into the pores, acting as a smart gate for gas entry to boost the selectivity. The hybrid membrane exhibits CO 2 permeability >600 barrer and enhanced CO 2 /N 2 selectivity >50, which surpasses the Robeson limit and shows potential in CO 2 /N 2 separation process. Molecular dynamics simulations confirm the gating effect of the IL layer of molecular thickness. In conclusion, this work demonstrates a universal strategy to improve CMS membrane performance by creating an IL-membrane interface and tuning the ion-pore interaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Insights into Probing the Effect of Molecular Weight of Poly(carboxybetaine methacrylate) on the Performance of Forward Osmosis Desalination

Zwitterionic polymers have proven to be a promising nonfouling material that can be applied in the design of selective layers of thin film composite (TFC) membranes. Extending the permeability and usage of TFC membranes have attracted increasing interest in membrane-based desalination processes since water-flux reduction associated with biofouling nowadays persists as a common challenge. By virtue of its strong hydration, this polymer category is very useful to counteract biofouling in marine and biomedical systems, but the benefits from their application in membrane technology are still emerging. The efficacy of the nonfouling property as a function of the polymer’s molecular weight remains unknown. In pursuit of that vision, this study fosters new scientific insights via probing different molecular weights of poly(carboxybetain methacrylate) (PCBMA) coated on the surface as a selective layer for the prepared TFC membranes. The coated zwitterionic membranes (zM) exhibited excellent performance in preventing water flux decay in a bench-scale forward osmosis system. The prepared zM membranes revealed enhanced hydrophilic properties and retained their operational water flux when compared to the control. Our results suggest that using an intermediate-size molecular weight (PCBMA M n 50,000) will result in the best operational performance. The intermediate size resulted in the lowest flux decline rate (R t ) of 0.01 ± 0.001 (zM-50) when compared to the unmodified control membrane 0.56 ± 0.071 (M0) after using a model BSA foulant solution. Furthermore, all coated membranes exhibited similar trends in the observed reverse salt flux profiles, as well. In conclusion, the constructed zM membranes will serve as a model to develop further selective layers in the construction of TFC membranes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Nanoscopic Plugs Block Hydrogen Crossover in Submicron Thick Proton-Conducting SiO 2 Membranes for Water Electrolysis

Zero-gap electrolyzers based on submicron thick proton-conducting oxide membranes (POMs) represent a promising approach to increasing the efficiency of H 2 production from water electrolysis while moving away from conventional perfluorosulfonic acid (PFSA) membranes. A critical barrier to the commercialization of such electrolyzers is that the ultrathin nature of POMs, which is necessary to achieve low cell resistance, makes them more susceptible to defects that can lead to unacceptably high rates of H 2 crossover. Herein, we demonstrate an approach to mitigate this problem through selective deposition of carbon-containing silicon oxide (SiO x C y ) “nanoplugs” into the defects of submicron thick SiO 2 membranes using a facile electrochemically mediated deposition process. Selective deposition of nanoplugs within the defects was verified by multiple characterization techniques, while scanning electrochemical microscopy (SECM) was used to confirm selective plugging of H 2 -crossover hotspots associated with defects at identical locations. Thanks to the use of nanoplugs, the H 2 permeance of 250 nm thick SiO 2 membranes was reduced by 5 to 6 orders of magnitude compared to the unmodified atomic layer deposition (ALD) SiO 2 membranes while having negligible impact on the ionic resistance of the membrane. These plug-modified membranes also enabled safe and stable operation of a zero-gap full cell electrolysis cell, in contrast to cells lacking nanoplugs that produced anode effluent streams having H 2 concentrations near or exceeding the lower flammability limit (LFL) of H 2 . Furthermore, beyond water electrolysis, this defect-sealing strategy has the potential to be broadly implemented in other applications, such as fuel cells and flow batteries, offering a versatile solution to mitigate crossover-related performance losses.

ALD SiO2↗
DOE OSTI2025

Optimizing microfluidic flow cell geometry for in situ resonant soft X-ray characterization of molecular nanostructures

Liquid-phase resonant soft X-ray scattering (LP-RSoXS) is an emerging label-free technique to probe chemically resolved nanostructures of molecular or hybrid materials in liquid environments. Still, quantitative analysis is hindered by the pressure-induced deformation of thin silicon nitride (SiN) membranes used as windows in microfluidic flow cells, which attenuates the signal in nonlinear ways, making experimental optimization difficult. Here, in this work, we directly characterize this deformation under experimental conditions for a variety of cell configurations. We use this to develop a predictive model that combines transmission effects of SiN bowing, incident X-ray beam profiles, and material-dependent resonant scattering cross sections to simulate the effective scattering intensity at the detector across the carbon K-edge. Maps of the total signal across the flow cell window reveal that increasing the window width and polymer concentration shifts the anisotropic intensity distributions from the center toward the edges of the window. It was determined that an optimal SiN thickness of 50 nm, with a window aperture of 104 μm, maximizes the total signal for typical solute concentrations and energies across the carbon K-edge. Our results overturn the assumption that corner regions dominate the scattering signal, offering explicit design guidelines for maximizing LP-RSoXS signals and significantly advancing the quantitative application of this technique to the characterization of molecular and hybrid nanostructured materials in liquids.

Grabner, Devin [Washington State Univ., Pullman, W↗
DOE OSTI2025

Neutral but Impactful: Gallium Cluster-Induced Nanopores from Beam-Blanked Gallium Ion Sources

Neutral atoms originating from liquid metal ion sources are an often-overlooked source of contamination and damage in focused ion beam microscopy. Beyond ions and single atoms, these sources also generate atom clusters. While most studies have investigated charged clusters, here we demonstrate that neutral clusters are also formed. These neutral clusters bypass the electrostatic beam blanking system, allowing them to impinge on samples even when the ion beam is blanked. We investigate this phenomenon using thin (≤20 nm) freestanding membranes of hexagonal boron nitride, silicon, and silicon nitride as targets. Randomly dispersed nanopores that form upon neutral cluster exposure are revealed. The average nanopore diameter is ∼2 nm with a narrow size distribution, suggesting that the atom clusters have a preferred size. Various electron microscopy techniques are used to characterize the nanopores, including high-resolution transmission electron microscopy, multislice ptychography, and electron energy-loss spectroscopy. Finally, we show how electron irradiation in the transmission electron microscope can be used to both remove any amorphous material that may clog the pores and to controllably grow the pores to specific sizes. Tunable nanopores such as these are interesting for nanofluidic applications requiring size-selective membranes.

Byrne, Dana O↗
DOE OSTI2022

Elasticity of two-dimensional ferroelectrics across their paraelectric phase transformation

The mechanical behavior of two-dimensional (2D) materials across 2D phase changes is unknown, and the finite temperature (T) elasticity of paradigmatic SnSe monolayers—ferroelectric 2D materials turning paraelectric as their unit cell turns from a rectangle into a square—is described here in a progressive manner. To begin with, their zero–T total energy landscape gives way to (Boltzmann-like) averages from which the elastic behavior is determined. Furthermore, these estimates are complemented with results from the strain-fluctuation method, which employs the energy landscape or ab initio molecular dynamics data. All approaches capture the coalescence of elastic moduli < C 11 (T) > = < C 22 (T) > due to the structural transformation. The broad evolution and sudden changes of elastic parameters < C 11 (T) >, < C 22 (T) >, and < C 12 (T) > of these atomically thin phase-change membranes establishes a heretofore overlooked connection among 2D materials and soft matter.

2-dimensional systems↗
DOE OSTI2025

Evaluation of Maximum Allowable Working Pressure and Svensson Burst Pressure Recommended in API 579-1 2021 Edition

Abstract API 579-1/ASME FFS-1 2021 Edition provides the minimum wall thickness, the maximum allowable working pressure (MAWP), and the membrane stress equations for thin and thick-walled cylindrical shells subject to internal pressure in Section 2C.3.3.1 of Appendix 2C – Thickness, MAWP, and Stress Equations for an FFS Assessment. The minimum wall thickness and MAWP are determined using the hoop stress and the Tresca yield criterion. Section 2C.7 – Estimation of Burst Pressure newly added the Svensson method for calculating burst pressure of cylindrical shells under internal pressure, where the plastic yielding is characterized by the von Mises yield criterion. For thin-walled cylinders, the von Mises flow solution of burst pressure in Equation (2C.179) was recommended. For thick-walled cylinders, an implicit burst pressure solution in an integral equation (2C.176) was recommended. But this integral equation is inconvenient to use in practice. It is well known that the classic plasticity theory includes the Tresca and von Mises yield criteria, with the Tresca criterion predicting a lower bound solution and the von Mises criteria predicting an upper bound solution. In addition, the present author developed an average shear stress yield criterion that can determine more accurate limit and burst pressures for thin and thick-walled cylinders. This work uses these three yield criteria to evaluate the minimum required wall thickness, MAWP and Svensson burst pressure recommended in the API 579 code.

burst pressure↗
DOE OSTI2021

FCET Solid Oxide Fuel Cell Testing and Development: CRADA 526 [Abstract only]

The purpose of the proposed project is for PNNL to test the performance of prototype solid oxide fuel cells (SOFCs) created by FCET. Such testing will provide FCET with independent performance data that can be communicated to potential clients and/or investors. Additionally, PNNL will collaborate with FCET on design changes to improve fuel cell performance. Intellectual property developed in this way will benefit FCET with improved products to market, and PNNL through royalty revenue. The key technology held by FCET is a process to deposit extremely thin layers of oxide materials, from 10-50 nm in thickness. The range of possible materials that can be deposited with their method is broad, but this project will focus on the yttria-stabilized zirconia (YSZ) electrolytes for SOFCs. Thin, gas tight YSZ membranes have been a long-sought target in SOFC research. The thinner the YSZ, the lower the cell resistance, and the higher performance of the cell (or the lower the operating temperature). 10-50 nm would be a major step change in YSZ thickness from the state of the art. PNNL can team with FCET on future R&D projects and push this technology forward to improve energy efficiency and reduce carbon emissions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Stamping Nanoparticles onto the Electrode for Rapid Electrochemical Analysis in Microfluidics

Electrochemical analysis is an efficient way to study various materials. However, nanoparticles are challenging due to the difficulty in fabricating a uniform electrode containing nanoparticles. We developed novel approaches to incorporate nanoparticles as a working electrode (WE) in a three-electrode microfluidic electrochemical cell. Specifically, conductive epoxy was used as a medium for direct application of nanoparticles onto the electrode surface. Three approaches in this work were illustrated, including sequence stamping, mix stamping, and droplet stamping. Shadow masking was used to form the conductive structure in the WE surface on a thin silicon nitride (SiN) membrane. Two types of nanomaterials, namely cerium oxide (CeO2) and graphite, were chosen as representative nanoparticles. The as-fabricated electrodes with attached particles were characterized using atomic force microscopy (AFM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Electrochemical analysis was performed to verify the feasibility of these nanoparticles as electrodes. Nanomaterials can be quickly assessed for their electrochemical properties using these new electrode fabrication methods in a microfluidic cell, offering a passport for rapid nanomaterial electrochemical analysis in the future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Evaluation of Maximum Allowable Working Pressure and Svensson Burst Pressure Recommended in API 579-1 2021 Edition

ABSTRACT API 579-1/ASME FFS-1 2021 Edition provides the minimum wall thickness, the maximum allowable working pressure (MAWP), and the membrane stress equations for thin and thick-walled cylindrical shells subject to internal pressure in Section 2C.3.3.1 of Appendix 2C – Thickness, MAWP, and Stress Equations for an FFS Assessment. The minimum wall thickness and MAWP are determined using the hoop stress and the Tresca yield criterion. Section 2C.7 – Estimation of Burst Pressure newly added the Svensson method for calculating burst pressure of cylindrical shells under internal pressure, where the plastic yielding is characterized by the von Mises yield criterion. For thin-walled cylinders, the von Mises flow solution of burst pressure in Equation (2C.179) was recommended. For thick-walled cylinders, an implicit burst pressure solution in an integral equation (2C.176) was recommended. But this integral equation is inconvenient to use in practice. It is well known that the classic plasticity theory includes the Tresca and von Mises yield criteria, with the Tresca criterion predicting a lower bound solution and the von Mises criteria predicting an upper bound solution. In addition, the present author developed an average shear stress yield criterion that can determine more accurate limit and burst pressures for thin and thick-walled cylinders. This work uses these three yield criteria to evaluate the minimum required wall thickness, MAWP and Svensson burst pressure recommended in the API 579 code.

burst pressure↗
DOE OSTI2025

Magnetic La 0.7 Sr 0.3 MnO 3 Membranes Synthesized by Etching a Sr 3 Al 2 O 6 Sacrificial Layer Using an Intermediary Manganite Protection Layer

The integration of perovskite oxides onto flexible substrates has witnessed significant advancements owing to the development of an epitaxial lift-off technique utilizing a Sr 3 Al 2 O 6 sacrificial layer. However, Sr 3 Al 2 O 6 is susceptible to instability in both air and high-temperature oxygen atmospheres, potentially leading to degradation during the growth of the functional oxide layer. In this study, we investigate the use of an oxygen-deficient La 0.7 Sr 0.3 MnO 3 as capping layer, and demonstrate its ability to stabilize Sr 3 Al 2 O 6 films in ambient air. We successfully synthesized freestanding La 0.7 Sr 0.3 MnO 3 membranes by etching this sacrificial layer and transferring them onto flexible polymer substrates. Importantly, the magnetic properties of the La 0.7 Sr 0.3 MnO 3 films are preserved in these membranes. Furthermore, our results underline that employing a thin manganite capping layer ensures both high structural quality and the preservation of functional properties in the resulting membranes.

Deposition↗
DOE OSTI2021

Membrane-Based Air Dehumidification Using Organic Ionic Liquid Desiccant

Membrane Ionic Liquid Desiccant Air Dehumidification (MILDAD) is a promising alternative to conventional dehumidification systems that employ mechanical compressors and refrigerant-based cooling with evaporator and condensing coils. However, its application has been limited due to high manufacturing and installation cost, durability issues, concerns with corrosion due to leakage and salt carry over into the downstream air and onto surfaces. This paper reviews substantial progress made with new systems based on combining advanced ionic membranes that are pressure resistant, thin walled with high water permeability, and non-porous with synthetic organic, non-crystalline ionic liquid desiccants. Alternative design configurations are discussed comparing cross flow shell-and-tube membrane contactors employing ionic membrane tubes through which ionic liquid desiccant air flows. Performance data for MILDAD prototypes is provided. Dehumidification of the incoming supply airstream and regeneration into exhausted building air is demonstrated. The latent effectiveness of the MILDAD system will be discussed along with some future steps to improve performance of the system.

Bahar, Bamdad↗
DOE OSTI2021

Membrane-Based Air Dehumidification Using Organic Ionic Liquid Desiccant

Membrane Ionic Liquid Desiccant Air Dehumidification (MILDAD) is a promising alternative to conventional dehumidification systems that employ mechanical compressors and refrigerant-based cooling with evaporator and condensing coils. However, its application has been limited due to high manufacturing and installation cost, durability issues, concerns with corrosion due to leakage and salt carry over into the downstream air and onto surfaces. This paper reviews substantial progress made with new systems based on combining advanced ionic membranes that are pressure resistant, thin walled with high water permeability, and non-porous with synthetic organic, non-crystalline ionic liquid desiccants. Alternative design configurations are discussed comparing cross flow shell-and-tube membrane contactors employing ionic membrane tubes through which ionic liquid desiccant air flows. Performance data for MILDAD prototypes is provided. Dehumidification of the incoming supply airstream and regeneration into exhausted building air is demonstrated. The latent effectiveness of the MILDAD system will be discussed along with some future steps to improve performance of the system.

ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATION↗