Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermally conductive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Impact of impurity-based phonon resonant scattering on thermal conductivity of single crystalline GaN

The impact of impurities on the thermal conductivity of halide vapor phase epitaxy gallium nitride (GaN) was studied. Phonon resonances with impurities, modeled as Lorentz oscillators, were used to explain the much lower thermal conductivity than predicted by the Debye–Callaway model. The resonance energies for the oscillators were determined by Raman spectroscopy for Mn and by mass difference approximation for C and Fe. Employing the obtained resonance energies and proportionality factors extracted as fitting parameters, the modified model showed a good agreement with the experimental data. While the doping decreased thermal conductivity for all temperatures, the room temperature values started decreasing significantly once the doping levels approached ~10 19 cm -3 . Consequently, required doping levels to achieve certain GaN-based devices may reduce the thermal conductivity of GaN by as much as 1/3.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Modeling the impact of high thermal conductivity paper on the performance and life of power transformers

Degradation of insulation paper is a key contributor to the failure of power transformers. Insulation degradation accelerates at elevated temperatures, which highlights the potential for better thermal management to prolong life. While several studies have analyzed the benefits of high thermal conductivity oil for reducing temperatures inside a transformer, this study is an initial assessment of the benefits of high thermal conductivity paper on transformer life. Blending particulates with cellulosic fibers offers a pathway for high thermal conductivity paper (with good dielectric properties), which can reduce internal temperatures. Presently, life extensions that can be achieved by the use of such thermally conducting papers were estimated, with the thermal conductivity of the paper being the key parameter under study. The analytical-numerical thermal model used in this study was validated against experimental measurements in a distribution transformer, adding confidence to the utility of the model. This model was then used to provide estimates of hot-spot temperature reduction resulting from the use of papers with higher thermal conductivity than baseline. Transformer life was predicted conventionally by tracking the degree of polymerization of paper over time, based on an Arrhenius model. Results indicate that increasing the thermal conductivity of paper from 0.2 W/mK (baseline) to 1W/mK reduces the hot spot temperature by 10°C. While degradation significantly depends on the moisture and oxygen content, the model shows that such a temperature reduction can increase life for all conditions, by as much as a factor of three.

42 ENGINEERING↗
DOE OSTI2023

Anisotropy in Thermal Conductivity of Ga2O3 under Irradiation: Ab-initio Investigations

Ga2O3 is a wide-bandgap semiconducting material known for its high breakdown electric field and thermal stability. Its various crystalline forms have shown great potential in power electronics, optoelectronics, and high-temperature applications. Specifically, ß-Ga2O3 has been recognized for its suitability in neutron and gamma radiation detection, making it ideal for sensor and detector applications [1]. Notably, ß-Ga2O3 exhibits anisotropic thermal conductivity, meaning that the magnitude of thermal conductivity varies with the crystallographic direction [2]. Under neutron irradiation, Ga2O3 undergoes a significant phenomenon, resulting in the formation of Helium bubbles within its crystalline matrix. The presence of Helium in Ga2O3 has been found to influence the material's anisotropic thermal conductivity. In this study, the objectives were twofold: firstly, to employ Density Functional Theory (DFT) to determine the most probable sites of Helium occupation in ß-Ga2O3, and secondly, to investigate the anisotropic variation in thermal conductivity when Helium is present in the crystalline matrix of ß-Ga2O3. These ab-initio DFT studies provide crucial insights into understanding the behavior of Helium in Ga2O3 and its impact on thermal conductivity, which can contribute to further advancements in sensor and detector applications based on this wide-bandgap semiconductor.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A new model for the effective thermal conductivity of polycrystalline solids

We introduce a novel model for the effective thermal conductivity of polycrystalline solids based on the thin-interface description of grain boundaries (GBs). In contrast to existing models, our new model treats a GB as an autonomous “phase” with its own thermal conductivity. The Kapitza resistance/conductance of a thin interface is then derived in terms of the interface thermal conductivity and width. In turn, the effective thermal conductivity of polycrystals is derived in terms of grain size, grain and GB conductivities, and GB width. This treatment allows the model to simulate the change of the Kapitza resistance/conductance with segregation/doping, GB structure/phase transition, or GB decohesion. Moreover, since the model assumes a finite width for GBs, it is expected to give better predictions than its sharp-interface-based counterparts for nanoscale grains. The predictions of the new model deviate from the corresponding ones from existing models by 1%–100% as the grain size approaches the GB width. High-fidelity finite-element simulations were conducted to validate the predictions of the new model. These simulations proved the higher accuracy of the new model. We also discuss how to generalize this treatment to other types of interfaces in heterogeneous materials. The advantages and limitations of the new model are summarized, and some future directions are highlighted.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Evolutionary multi-objective optimization and Pareto-frontal uncertainty quantification of interatomic forcefields for thermal conductivity simulations

Predictive Molecular Dynamics simulations of thermal transport require forcefields that can simultaneously reproduce several structural, thermodynamic and vibrational properties of materials like lattice constants, phonon density of states, and specific heat. This requires a multi-objective optimization approach for forcefield parameterization. Existing methodologies for forcefield parameterization use ad-hoc and empirical weighting schemes to convert this into a single-objective optimization problem. Here, we provide and describe software to perform multi-objective optimization of Stillinger–Weber forcefields (SWFF) for two-dimensional layered materials using the recently developed 3rd generation non-dominated sorting genetic algorithm (NSGA-III). NSGA-III converges to the set of optimal forcefields lying on the Pareto front in the multi-dimensional objective space. This set of forcefields is used for uncertainty quantification of computed thermal conductivity due to variability in the forcefield parameters. We demonstrate this new optimization scheme by constructing a SWFF for a representative two-dimensional material, 2H-MoSe 2 and quantifying the uncertainty in their computed thermal conductivity.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Thermal conductivity of rutile germanium dioxide

Power electronics seek to improve power conversion of devices by utilizing materials with a wide bandgap, high carrier mobility, and high thermal conductivity. Due to its wide bandgap of 4.5 eV, b-Ga 2 O 3 has received much attention for high-voltage electronic device research. However, it suffers from inefficient thermal conduction that originates from its low-symmetry crystal structure. Rutile germanium oxide (r-GeO 2 ) has been identified as an alternative ultra-wide-bandgap (4.68 eV) semiconductor with predicted high electron mobility and ambipolar dopability; however, its thermal conductivity is unknown. Here, we characterize the thermal conductivity of r-GeO 2 as a function of temperature by first-principles calculations, experimental synthesis, and thermal characterization. The calculations predict an anisotropic phonon-limited thermal conductivity for r-GeO 2 of 37W m –1 K –1 along the a direction and 58W m –1 K –1 along the c direction at 300K where the phonon-limited thermal conductivity predominantly occurs via the acoustic modes. Experimentally, we measured the value of 51W m –1 K –1 at 300K for hot-pressed, polycrystalline r-GeO2 pellets. The measured value is close to our directionally averaged theoretical value, and the temperature dependence of ~1/T is also consistent with our theory prediction, indicating that thermal transport in our r-GeO 2 samples at room temperature and above is governed by phonon scattering. Furthermore, our results reveal that high-symmetry UWBG materials, such as r-GeO 2 , may be the key to efficient power electronics.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Thermal conductivity of austenitic stainless steel, SRM 735, from 5 to 280 K

Thermal conductivity and electrical resistivity measurements were conducted on two lots of an austenitic stainless steel. Electrical resistivity measurements were performed on the second lot, both before and after the material was hot-swaged and reannealed to a size 1/10 the original diameter. These measurements indicate that this steel can be swaged and reannealed without an appreciable change in thermal conductivity. Electrical resistivity measurements as well as direct thermal conductivity measurements on several specimens from both lots indicate a material variability in these lots of less than 1% in thermal conductivity.

Hust, J. G.↗
DOE OSTI2023

Thermal conductivity measurement using modulated photothermal radiometry for nitrate and chloride molten salts

Molten salts are being used or explored for thermal energy storage and conversion systems in concentrating solar power and nuclear power plants. Thermal conductivity of molten salts is an important thermophysical property dictating the performance and cost of these systems, but its accurate measurement has been challenging, as evidenced by wide scattering of existing data in literature. The corrosive and conducting nature of these fluids also leads to time consuming sample preparation processes of many contact-based measurements. Here, in this work, we report the measurement of thermal conductivity of molten salts using a modulated photothermal radiometry (MPR) technique, which is a laser-based, non-contact, frequency-domain method adopted for molten salts for the first time. By unitizing the advantages of front side sensing of frequency-domain measurements and the vertical holder orientation, the technique can minimize the natural convection and salt creeping effects, thus yielding accurate molten salt thermal conductivity . The MPR technique is first calibrated using standard molten materials including paraffin wax and sulfur. It is then applied on measuring pure nitrate salts (NaNO 3 and KNO 3 ), solar salt (NaNO 3 –KNO 3 mixture), and chloride salt (NaCl–KCl–MgCl 2 ). The measurement results are compared with data from literature, especially those obtained from laser flash analysis (LFA). Our results demonstrate that the MPR is a convenient and reliable technique of measuring thermal conductivity of molten salts. Accurate thermal conductivity data of molten salts will be valuable in developing the next-generation high-temperature thermal energy storage and conversion systems.

14 SOLAR ENERGY↗
DOE OSTI2021

Thermal conductivity of α -U with point defects

Here, we develop a theoretical model for thermal conductivity of α-U that combines density functional theory calculations and the coupled electron–phonon Boltzmann transport equation. The model incorporates both electron and phonon contributions to thermal conductivity and achieves good agreement with experimental data over a wide temperature range. The dominant scattering mechanism governing thermal transport in α-U at different temperatures is examined. By including phonon–defect and electron–defect scatterings in the model, we study the effect of point defects including U-vacancy, U-interstitial, and Zr-substitution on the thermal conductivity of α-U. The degradation of anisotropic thermal conductivity due to point defects as a function of defect concentration, defect type, and temperature is reported. This model provides insights into the impact of defects on both phonon and electron thermal transport. It will promote the fundamental understanding of thermal transport in α-U and provide a ground for investigation of coupled electron–phonon transport in metallic materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Thermal Conductivity of Graphene Coated Copper Under Uniaxial Tensile Mechanical Strain

Graphene continues to demonstrate promise as a highly effective barrier coating, even at only one atom thick. The thermal properties of this coating are also promising to allow diffusion of heat across the surface, as the isolated graphene is an intrinsically good thermal conductor, yet this and its behavior under mechanical deformation has been less extensively studied. This report demonstrates that the in-plane thermal conductivity and interfacial thermal conductance of graphene coatings on copper are affected by mechanical strain. By inducing a strain in the copper substrate, the Raman-active 2D peak exhibits a change in position as well as a change in laser power dependence as the copper substrate is uniaxially elongated to a maximum of 0.5%. Non-linear trends in thermal conductivity are observed with tensile strain in samples with differing strain transfer rates from the substrate, indicating the close correlation between intrinsic thermal conduction and interfacial properties in atomically thin coatings transferred onto metals.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Systematic over-estimation of lattice thermal conductivity in materials with electrically-resistive grain boundaries

Reducing the thermal conductivity κ of a material via nano-structuring to create small grain sizes is one of the most common strategies to improve thermoelectric materials. In such polycrystalline materials heat carrying phonons are scattered at the grain boundaries, which directly improves the thermoelectric quality factor and ultimately the figure-of-merit zT. In some cases, however, such as in Mg 3 Sb 2 , SnSe, and Mg 2 Si an opposite trend is found where higher lattice thermal conductivity reported in small grain polycrystalline material than in large grain or single crystal materials. This unphysical result indicates a problem with the conventional use of the Wiedemann–Franz law. Here, we trace this problematic finding to the electrical resistance at the grain boundaries, which leads to an overestimation of the phonon or lattice contribution of the thermal conductivity κ L . In materials with significant grain boundary electrical resistance, the estimated electronic contribution to the thermal conductivity LσT is low because the measured electrical conductivity σ is low. However within the grain electrons may still be transporting more heat than the total conductivity suggests, leading to an overestimation of κ L if the conventional κ L = κ – LσT is used with the measured values of κ and σ. Here, the overestimation of κL in small-grain samples is shown to be pervasive across a broad range of thermoelectric materials, including Mg 3 Sb 2 , Mg 2 Si, PbTe, PbSe, SnSe, (Hf,Zr)CoSb, CoSb 3 , and Bi 2 Te 3 alloys, and a correction is necessary to properly understand and predict their charge and heat transport.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Thermal Conductivity of AM Fabricated Stainless Steel 316L Part

Thermal properties are an integral part of many diverse engineering applications, and additive manufacturing (AM), particularly laser powder bed fusion (LPBF) is shown to affect thermal properties due to the laser processing parameters. For 316L stainless steel, there is little prior research to determine the effects of the process on thermal properties. In this work, the temperature gradient is shown to create uniform, chess board-like distributions of grains in the build direction. These zones create dislocations which were visualized with EBSD techniques. Processing parameters cause hierarchal grain size distribution, with localized concentrations of small grains and large grains. Thermomechanical stresses in the rapid solidification increases dislocation density during grain formation. Previous research shows a higher density of dislocations decreases local thermal conductivity. Local and bulk thermal conductivity are shown in this work to have statistically lowered values to an average of 10-12 W/m-K compared to 14 W/m-K for conventional 316L.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Low thermal conductivity in Bi 8 CsO 8 SeX 7 (X = Cl, Br) by combining different structural motifs

Understanding the structure–property relationships of materials in order to supress thermal conductivity is crucial for developing efficient thermoelectric generators and thermal barrier coatings. Low thermal conductivity materials can often contain a single dominant phonon scattering mechanism. Here, we highlight how combining different structural features into one material can aid in the design and identification of new materials with low thermal conductivities. We synthesise two new mixed-anion materials, Bi 8 CsO 8 SeX 7 (X = Cl and Br), with low thermal conductivities of 0.27(2) and 0.22(2) W m -1 K -1 respectively, measured along their c-axes at room temperature. The Bi 8 CsO 8 SeX 7 materials possess a combination of bond strength hierarchies, Cs + vacancies, and low frequency Cs + rattling. These different features significantly inhibit phonon transport along different crystallographic directions. Due to sharp bond strength contrast between the van der Waals gaps and [Bi 2 O 2 ] 2+ layers, the Bi 8 CsO 8 SeX 7 materials exhibit thermal conductivities <50% of the theoretical minimum when measured along the stacking direction. Conversely, the thermal conductivity associated with the ab-plane is reduced by Cs + rattling when compared to the structurally and compositionally related BiOCl.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Implications of phonon anisotropy on thermal conductivity of fluorite oxides

Abstract Fluorite oxides are attractive ionic compounds for a range of applications with critical thermal management requirements. In view of recent reports alluding to anisotropic thermal conductivity in this face-centered cubic crystalline systems, we perform a detailed analysis of the impact of direction-dependent phonon group velocities and lifetimes on the thermal transport of fluorite oxides. We demonstrate that the bulk thermal conductivity of this class of materials remains isotropic despite notable anisotropy in phonon lifetime and group velocity. However, breaking the symmetry of the phonon lifetime under external stimuli including boundary scattering present in nonequilibrium molecular dynamics simulations of finite size simulation cell gives rise to apparent thermal conductivity anisotropy. We observe that for accurate determination of thermal conductivity, it is important to consider phonon properties not only along high symmetry directions commonly measured in inelastic neutron or x-ray scattering experiments but also of those along lower symmetry. Our results suggests that certain low symmetry directions have a larger contribution to thermal conductivity compared to high symmetry ones.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1996

The thermal conductance of solid-lubricated bearings at cryogenic temperatures in vacuum

The thermal conductance of Hertzian contacts is of great importance to cryogenic spacecraft mechanisms such as the Infra-Red Space Observatory (ISO) and the Far Infra-Red Space Telescope (FIRST). At cryogenic temperatures, cooling of mechanism shafts and associated components occurs via conduction through the bearings. When fluid lubricants are cooled below their pour points, they no longer lubricate effectively, and it is necessary to use low shear strength solid lubricants. Currently, only very limited low temperature data exists on the thermal conductance of Hertzian contacts in both unlubricated and lubricated conditions. This paper reports on measurements of thermal conductance made on stationary ball bearings under cryo-vacuum conditions. Quantitative data is provided to support the development of computer models predicting the thermal conductance of Hertzian contacts and solid lubricants at cryogenic temperatures.

Anderson, M. J.↗
NASA NTRS2005

An Improved Thermal Conductivity Polyurethane Composite for a Space Borne 20KV Power Supply

This effort was designed to find a way to reduce the temperature rise of critical components of a 20KV High Voltage Power Supply (HVPS) by improving the overall thermal conductivity of the encapsulated modules. Three strategies were evaluated by developing complete procedures, preparing samples, and performing tests. The three strategies were: 1. Improve the thermal conductivity of the polyurethane encapsulant through the addition of thermally conductive powder while minimizing impact on other characteristics of the encapsulant. 2. Improve the thermal conductivity of the polyurethane encapsulated assembly by the addition of a slab of thermally conductive, electrically insulating material, which is to act as a heat spreader. 3. Employ a more thermally conductive substrate (Al203) with the existing encapsulation scheme. The materials were chosen based on the following criteria: high dielectric breakdown strength; high thermal conductivity, ease of manufacturing, high compliance, and other standard space qualified materials properties (low out-gassing, etc.). An optimized cure was determined by a statistical design of experiments for both filled and unfilled materials. The materials were characterized for the desired properties and a complete process was developed and tested. The thermal performance was substantially improved and the strategies may be used for space flight.

Pb free↗
DOE OSTI2021

Ultrahigh thermal conductivity in three-dimensional covalent organic frameworks

Covalent organic frameworks (COFs) are a new, growing class of crystalline polymers with exceptional characteristics such as low density, mechanical strength, and flexibility. Taking three-dimensional (3D) COF-300 derivatives as an example, we apply molecular dynamics simulations to show that ultrahigh thermal conductivity (>15 W/(mK)) is achieved at a pore size of d = 0.63 nm. This is the first observation of such an outstanding intrinsic thermal conductivity of a 3D polymer in all directions. Further temperature-dependent thermal conductivity calculations and X-ray diffraction (XRD) patterns highlight the importance of maintaining microscopic order for a large thermal conductivity. We also demonstrate that the tunability and anisotropy in COFs provide sufficient room to engineer and obtain desired thermal conductivity. These findings provide a fundamental understanding of structure-thermal conductivity relation in COFs and shine a light on high-thermal-conductivity COFs for thermal management applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Enhancing thermal conductivity and toughness of cellulose nanofibril/boron nitride nanosheet composites

Generally, the thermal conductivity (TC) of composite based on cellulose nanofibrils (CNF) is improved by adding thermal conductive filler, which inevitably leads to the loss of its mechanical properties. Here, in this work, it is the first to simultaneously improve the toughness and TC of CNF/boron nitride nanosheets (BNNS) composite from the perspective of thermal conductive filler addition and CNF crystal change. The hydrophilic-modified BNNSs were successfully prepared by xylose-assisted ball-milling prior to adding into CNF. Compared with that of CNF film (1.34 W/(m·K)), the in-plane TC of CNF/BNNS composite (12.68 W/(m·K)) increased significantly by 846 % with loading 30 % BNNS. Afterwards, both toughness (8.0 MJ·m -3 , increased ~250 %) and TC (14.7 W/(m·K), increased ~16 %) of CNF/BNNS composite were further enhanced significantly by mercerization with 12.5 % NaOH solution. The simultaneously improvement of toughness and TC is unprecedented in related studies, which contributes to the effective preparation of thermal management materials.

36 MATERIALS SCIENCE↗