SEARCH · Engineering Papers

Results for “stable glass”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

DOE OSTI2022

An electrochemically stable homogeneous glassy electrolyte formed at room temperature for all-solid-state sodium batteries

All-solid-state sodium batteries (ASSSBs) are promising candidates for grid-scale energy storage. However, there are no commercialized ASSSBs yet, in part due to the lack of a low-cost, simple-to-fabricate solid electrolyte (SE) with electrochemical stability towards Na metal. In this work, we report a family of oxysulfide glass SEs (Na 3 PS 4-x O x , where 0 < x ≤ 60) that not only exhibit the highest critical current density among all Na-ion conducting sulfide-based SEs, but also enable high-performance ambient-temperature sodium-sulfur batteries. By forming bridging oxygen units, the Na 3 PS 4-x Ox SEs undergo pressure-induced sintering at room temperature, resulting in a fully homogeneous glass structure with robust mechanical properties. Furthermore, the self-passivating solid electrolyte interphase at the Na|SE interface is critical for interface stabilization and reversible Na plating and stripping. The new structural and compositional design strategies presented here provide a new paradigm in the development of safe, low-cost, energy-dense, and long-lifetime ASSSBs.

25 ENERGY STORAGE↗

DOE OSTI2020

Deformation behavior of metallic glass composites and plasticity accommodation at microstructural length-scales

Bulk metallic glass matrix composites represent a unique microstructural design strategy for overcoming the strength/ductility trade-off in structural alloys. Site-specific mechanical behavior of a Ti-based bulk metallic glass composite was evaluated at microstructural length-scale. The micro-pillars on the amorphous matrix showed on average a yield point of 1.9 GPa followed by serrated plastic deformation characteristic of shear banding. In contrast, micro-pillars on the crystalline dendritic phase showed a much lower yield strength of 0.72 GPa on average for the four different crystallographic orientations chosen, smooth plastic flow with no recognizable load burst, and stable strain-hardening after yield point. A number of micro-pillars were made at the interface between the glassy matrix and the crystalline dendrite. The mixed micro-pillars showed homogeneous deformation and greater plasticity which was attributed to their smaller stored elastic energy. Shear bands initiated in the amorphous matrix were arrested by the crystalline dendrite, which accommodated plasticity through slip bands and dislocations pile-ups. The interface remained intact after plastic deformation, with no observable signs of devitrification in the amorphous phase.

Bulk metallic glass matrix composite, Micro-pillar↗

NASA NTRS1991

Effect of molecular weight on polyphenylquinoxaline properties

A series of polyphenyl quinoxalines with different molecular weight and end-groups were prepared by varying monomer stoichiometry. Thus, 4,4'-oxydibenzil and 3,3'-diaminobenzidine were reacted in a 50/50 mixture of m-cresol and xylenes. Reaction concentration, temperature, and stir rate were studied and found to have an effect on polymer properties. Number and weight average molecular weights were determined and correlated well with viscosity data. Glass transition temperatures were determined and found to vary with molecular weight and end-groups. Mechanical properties of films from polymers with different molecular weights were essentially identical at room temperature but showed significant differences at 232 C. Diamine terminated polymers were found to be much less thermooxidatively stable than benzil terminated polymers when aged at 316 C even though dynamic thermogravimetric analysis revealed only slight differences. Lower molecular weight polymers exhibited better processability than higher molecular weight polymers.

Jensen, Brian J.↗

NASA NTRS1974

Development of space stable thermal control coatings for use on large space vehicles

The development of a large scale manufacturing method for the production of a stable zinc orthotitanate pigment by means of an oxalate co-precipitation method is examined. Pigments were prepared at various temperatures, and major emphasis was placed on the determination of the important parameters of post-precipitation firing and treatment. A large-scale process for the modification of a glass resin binder was developed and paints were formulated using the binder.

Gilligan, J. E.↗

NASA NTRS1994

New directions in phthalocyanine pigments

Phthalocyanines have been used as a pigment in coatings and related applications for many years. These pigments are some of the most stable organic pigments known. The phthalo blue and green pigments have been known to be ultraviolet (UV) stable and thermally stable to over 400 C. These phthalocyanines are both a semiconductor and photoconductor, exhibiting catalytic activity and photostabilization capability of polymers. Many metal free and metallic phthalocyanine derivatives have been prepared. Development of the new classes of phthalocyanine pigment could be used as coating on NASA spacecraft material such as glass to decrease the optical degradation from UV light, the outside of the space station modules for UV protection, and coating on solar cells to increase lifetime and efficiency.

Trinh, Diep VO↗

NASA NTRS1979

Development of fire-resistant, low smoke generating, thermally stable end items for commercial aircraft and spacecraft using a basic polyimide resin

Experimental data pertinent to flexible resilient foams, low density wall panels, high strength floor panels and thermal acoustical insulation are presented. An evaluation of the effect of the heterocyclic diamine component on the compression set of the foams was carried out. Processes and compositions for fabricating wall panels were evaluated. Thermal acoustical polyimide materials were developed to replace conventional glass batting insulation. To reduce the thermal stresses and improve the burn through resistance, cross linked polyimide foams were developed but not evaluated.

Gagliani, J.↗

NASA NTRS1980

Transverse injection of a particle-laden liquid jet in supersonic flow: A three-phase flow

The results of a two part study of the behavior of particle laden liquid jets injected into air are presented. Water was used as the liquid carrier and either 1-37 or 13-44 microns diam. spherical glass beads with a specific gravity of 2.8-3.0 as the particles. The observations were mainly photographic. The breakup of jets injected into still air was investigated as a function of particle loading, and the results were compared to the pure liquid jet case. The jets were found to be more stable with particles present. The length to breakup was increased, and the formation of satellite droplets was suppressed. The penetration and breakup of transverse jets in a Mach 3.0 air stream was studied. The general breakup mechanism of wave formation was found to be the same as for the all liquid case. Significant separation of the phases was observed, and the penetration of the liquid phase was reduced compared to all liquid cases at the same value of the jet to free stream momentum flux ratio.

Schetz, J. A.↗

NASA NTRS1987

Tensile behavior of glass/ceramic composite materials at elevated temperatures

This paper describes the tensile behavior of high-temperature composite materials containing continuous Nicalon ceramic fiber reinforcement and glass and glass/ceramic matrices. The longitudinal properties of these materials can approach theoretical expectations for brittle matrix composites, failing at a strength and ultimate strain level consistent with those of the fibers. The brittle, high-modulus matrices result in a nonlinear stress-strain curve due to the onset of stable matrix cracking at 10 to 30 percent of the fiber strain to failure, and at strains below this range in off-axis plies. Current fibers and matrices can provide attractive properties well above 1000 C, but composites experience embrittlement in oxidizing atmospheres at 800 to 1000 C due to oxidation of a carbon interface reaction layer.The oxidation effect greatly increases the interface bond strength, causing composite embrittlement.

Mandell, J. F.↗

NASA NTRS1988

Novel polyamide-imines

An account is given of tough, thermally stable linear polyimides containing amide linkages that recommend themselves for use in high temperature-resistant films and coatings as well as matrix resins for graphite-reinforced structures. Four such polymers were synthesized from unsubstituted amide diamines, and two others from N-substituted amide diamines. High inherent viscosities and glass transition temperatures were obtained. The films exhibit good resistance to organic solvents. Films of the 4,4-prime-isomer polyamide-imide yielded exceptionally high modulus and toughness during impact evaluation.

Dezern, James F.↗

NASA NTRS1995

Whisker/Cone growth on the thermal control surfaces experiment no. S0069

An unusual surface 'growth' was found during scanning electron microscope (SEM) investigations of the Thermal Control Surface Experiment (TCSE) S0069 front thermal cover. This 'growth' is similar to the cone type whisker growth phenomena as studied by G. K. Wehner beginning in the 1960's. Extensive analysis has identified the most probable composition of the whiskers to be a silicate type glass. Sources of the growth material are outgassing products from the experiment and orbital atomic oxygen, which occurs naturally at the orbital altitudes of the LDEF mission in the form of neutral atomic oxygen. The highly ordered symmetry and directionality of the whiskers are attributed to the long term (5.8 year) stable flight orientation of the LDEF.

Zwiener, James M.↗

DOE OSTI2021

Shape memory effect in metallic glasses

Shape memory effect (SME), mainly present in crystalline Ti-Ni alloys, is basically missing in metallic glasses (MGs) that lack the long-range periodic order of crystals. In this work, we report experimental results of SME in annealed MGs, in which the low-energy configuration state recovery is observed by both differential scanning calorimetry and X-ray photon correlation spectroscopy. We elucidate the origin of SME in MGs under the potential energy landscape framework, i.e., after annealing, the energy of MGs enters into a deep basin and atoms are located in the low-energy configuration state. Albeit deviating from their relative stable configurations by temperature changes, atoms in the annealed MGs tend to return to the low-energy atomic configurations along certain trajectories as pre-annealing temperature is approached, These results could extend the application of MGs as functional materials by directionally manipulating their energy states via annealing and rejuvenation.

36 MATERIALS SCIENCE↗

NASA NTRS1971

Development of a space stable thermal control coatings for use in large space vehicles

The preparation and evaluation of zinc orthotitanate and of several new pigments and the environmental testing and evaluation of these pigments and of coatings made from them constitute the bulk of the work accomplished. New pigments were prepared and EPR spectra of pigments and their precursor compounds studied. Results of extensive testing of commercially-available, strippable, protective coatings are reported; Owens-Illinois 650 glass resin has been stabilized against progressive mechanical failures; and definite improvements have been noted. A zinc oxide pigmented lithium silicate paint has demonstrated very good ultraviolet stability.

Gilligan, J. E.↗

NASA NTRS1982

A new brominated polymeric additive for flame retardant glass-filled polybutylene terephthalate

Attention is called to the undesirable effects (poor ultraviolet light stability and blooming) sometimes introduced by brominated flame retarders. A brominated polymeric additive (BPA) with little or none of these undesirable side effects is compared with decabromobiphenyl oxide (DBBPO). The additive bears the product name F-2300. It is found to be more easily dispersed than DBBPO. The F-2300 is as effective as the DBBPO in the oxygen index test. The improved efficiency of the F-2300 may be explained by its better dispersion in polybutylene terephthalate (PBT). Glass-filled PBT containing F-2300 is found to be more resistant to UV degradation than DBBPO-containing formulas. Formulations with F-2300 therefore have a longer useful outdoor life. F-2300 is a diglycidyl-type polymer containing 50 percent aromatically bound bromine. Its melting point is 112 C, and it is stable up to 372 C. It is pointed out that since its melts at a relatively low temperature, it can be introduced into the formulation as a large agglomerate and still be dispersed evenly throughout the polymer.

Nir, Z.↗

NASA NTRS2009

Liquid Crystalline Thermosets from Ester, Ester-imide, and Ester-amide Oligomers

Main chain thermotropic liquid crystal esters, ester-imides, and ester-amides were prepared from AA, BB, and AB type monomeric materials and end-capped with phenylacetylene, phenylmaleimide, or nadimide reactive end-groups. The end-capped liquid crystal oligomers are thermotropic and have, preferably, molecular weights in the range of approximately 1000-15,000 grams per mole. The end-capped liquid crystaloligomers have broad liquid crystalline melting ranges and exhibit high melt stability and very low melt viscosities at accessible temperatures. The end-capped liquid crystal oli-gomers are stable forup to an hour in the melt phase. They are highly processable by a variety of melt process shape forming and blending techniques. Once processed and shaped, the end-capped liquid crystal oigomers were heated to further polymerize and form liquid crystalline thermosets (LCT). The fully cured products are rubbers above their glass transition temperatures.

Dingemans, Theodorus J.↗

NASA NTRS2016

Laboratory Testing and Performance Verification of the CHARIS Integral Field Spectrograph

The Coronagraphic High Angular Resolution Imaging Spectrograph (CHARIS) is an integral field spectrograph (IFS) that has been built for the Subaru telescope. CHARIS has two imaging modes; the high-resolution mode is R82, R69, and R82 in J, H, and K bands respectively while the low-resolution discovery mode uses a second low-resolution prism with R19 spanning 1.15-2.37 microns (J+H+K bands). The discovery mode is meant to augment the low inner working angle of the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) adaptive optics system, which feeds CHARIS a coronagraphic image. The goal is to detect and characterize brown dwarfs and hot Jovian planets down to contrasts five orders of magnitude dimmer than their parent star at an inner working angle as low as 80 milliarcseconds. CHARIS constrains spectral crosstalk through several key aspects of the optical design. Additionally, the repeatability of alignment of certain optical components is critical to the calibrations required for the data pipeline. Specifically the relative alignment of the lens let array, prism, and detector must be highly stable and repeatable between imaging modes. We report on the measured repeatability and stability of these mechanisms, measurements of spectral crosstalk in the instrument, and the propagation of these errors through the data pipeline. Another key design feature of CHARIS is the prism, which pairs Barium Fluoride with Ohara L-BBH2 high index glass. The dispersion of the prism is significantly more uniform than other glass choices, and the CHARIS prisms represent the first NIR astronomical instrument that uses L-BBH2as the high index material. This material choice was key to the utility of the discovery mode, so significant efforts were put into cryogenic characterization of the material. The final performance of the prism assemblies in their operating environment is described in detail. The spectrograph is going through final alignment, cryogenic cycling, and is being delivered to the Subaru telescope in April 2016. This paper is a report on the laboratory performance of the spectrograph, and its current status in the commissioning process so that observers will better understand the instrument capabilities. We will also discuss the lessons learned during the testing process and their impact on future high-contrast imaging spectrographs for wavefront control.

Coronagraphic High Angular Resolution Imaging Spec↗

DOE OSTI2025

Single-Ion Conducting Polymer Electrolyte Enabled via Aza-Michael Addition

Single-ion conducting polymer electrolytes present a possible route for achieving high energy density next-generation batteries due to their flexible nature and high cation transport number. The trifluoromethanesulfonimide (TFSI) functional group represents one of the most efficient tethered anions for Li-ion conductivity. However, the covalent attachment of TFSI groups into polymer electrolytes has been challenging and costly due to its synthetic difficulty and limited commercial availability of building blocks. Here, we present a new polymer electrolyte synthesized by the Michael addition reaction between poly(allylamine) (PAA) and a vinyl TFSI anion under mild reaction conditions. The resulting PAATFSI exhibits a lower glass transition temperature and several orders of magnitude higher Li-ion conductivity than similar TFSI-based single-ion conducting homopolymers in the dry state. Moreover, PAATFSI exhibits excellent Li-ion conductivity (2.7 × 10 –4 S/cm at 30 °C) with the addition of a plasticizer (60 wt % of carbonate solvent), which enables stable lithium–metal battery performance. In conclusion, this study demonstrates a facile route for the synthesis of new single-ion conducting polymer electrolytes that opens a library of possibilities to enable the realization of polymer-based batteries.

25 ENERGY STORAGE↗

DOE OSTI2020

Surface oxidation and crystallization of FeNi-Based soft magnetic nanocrystalline and amorphous nanocomposite alloys

In this work, we present characterization of surface oxidation and crystallization behavior of Metal Amorphous Nanocomposite (MANC) (Fe 70 Ni 30 ) 80 Nb 4 Si 2 B 14 alloys via complementary x-ray diffraction, electron microscopy, and x-ray photoelectron spectroscopy techniques. An adherent amorphous oxide of roughly 15–20 nm in thickness is observed on the wheel side of the ribbon, enriched in Fe relative to Ni and with significant content of Si and Nb as would be expected based upon a comparison of the Gibbs free energy of formation of the stable oxide phases. The amorphous character of the oxide is likely to result from the significant Si-content coupled with the amorphous and nanocrystalline character of the underlying metallic layer. Higher density of FeNi-enriched nanocrystals is also observed within ~100 nm of the wheel-side surface, presumably due to reduction in local glass former concentration. A rough, crystalline copper oxide layer is also present and forms through contact between the copper wheel and the solidifying melt during the rapid solidification process. On the air side of the ribbon, a crystalline oxide layer of ~15–20 nm is formed as well as intergranular oxidation that penetrates along the grain boundaries between highly textured surface crystallites of ~50–100 nm in size. The crystalline nature of the oxide on these surfaces is asserted to result from the lack of significant Si-content and the pre-existing surface crystallites that form during the rapid solidification process which promote a crystalline oxide surface layer. Furthermore, these results shed new insights into the details of surface oxidation and can help to inform processing and alloy composition adjustments which seek to tailor surface properties.

36 MATERIALS SCIENCE↗

NASA NTRS1975

Study of improved resins for advanced supersonic technology composites. Part 1: Heteroaromatic polymers containing ether groups. Part 2: Curing chemistry of aromatic polymers and composite studies

Fourteen ether-containing, aromatic dianhydrides have been synthesized from N-phenyl-3 or 4-nitrophthalimide and various bisphenols. The process involves nucleophilic displacement of activated nitro groups with bisphenolate ions. Ether-containing dianhydrides were indefinitely stable in the presence of atmospheric moisture. One-step, high temperature solution polymerization of the ether-containing dianhydrides with m-phenylene diamine, 4,4'-oxydianiline and 1, 3-bis(4-aminophenoxy)benzene afforded 42 polyetherimides. The polyetherimides were all soluble in m-cresol except two which were found to be crystalline. The glass transition temperatures of the polyetherimides ranged from 178 to 277 C. Soluble polybenzimidazopyrrolones containing ether groups were also prepared from the same ether-containing dianhydrides and aromatic tetraamines by one-step solution polymerization. Using low molecular weight polyetherimides, various thermoset resin systems were developed and tested as matrices for fiber-reinforced composites. The curing chemistry involving reaction of the phthalonitrile group and the o-diaminophenyl group was found to be generally applicable to crosslinking various aromatic polymers other than polyimides.

Takekoshi, T.↗