Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “simplified simulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Effects of Geometric Azimuthal Asymmetries of the PPM Stack on Electron Beam Characteristics

The effects of geometric azimuthally asymmetric properties of a periodic permanent magnet (PPM) focusing stack on electron beam characteristics obtained using a fully three dimensional (3D) particle-in-cell (PIC) code will be presented. The simulation model, using MAFIA (Solution of MAxwell's equations by the Finite-Integration-Algorithm), incorporates 3D behavior of the beam immersed in static fields calculated directly from the exact geometry and material properties of the 3D magnetic focusing structure. The Hughes 8916H, 18-40 GHz helical TWT for the millimeter-wave power module (MMPM) was used as a prototype. Firstly, the effects of C-magnets used at the input and output of the TWT to allow for coupling of the RF signal into and out of the tube are considered. The 8916H input and output C-magnets differ because coaxial couplers are used at the input and waveguide couplers are used at the output The repositioning of the beam from its central axis due to the inclusion of the output C-magnet was found to be most significant. The modeled output C-magnet and its orientation in the Cartesian coordinate system is shown, and a two-dimensional beam profile including the output C-magnet is also shown. A table presents the shift of the beam center off the central axis relative to the average radius of the beam at the longitudinal points A, B and C designated on an enclosed figure. Secondly, the addition of shunts, or rectangular iron pieces applied manually by a skilled technician in order to improve beam transmission, is considered. The shunts are applied to the top of the tube; thus, azimuthal symmetry of the focusing stack is interrupted. Although shunts are typically added during RF focusing, they are also typically added at the input section of the tube where RF forces are minimal, making an electron optics analysis meaningful. Because several shunts are usually applied to one pole piece, the simulations have been simplified by modeling a half washer with the same radius and longitudinal length as a shunt over the entire x, positive-y half of the transverse plane. A modeled pole piece and shunt as described are shown. Lastly, in order to study the effects of magnet misalignments, a magnet in the PPM stack was arbitrarily chosen and adjusted so that its central axis was shifted both 0.7 percent and 1.0 percent of the magnet outer diameter in the positive-y direction. In practice, positioning the magnets so that their central axis is accurately aligned with the central axis of the tube is challenging. Thus, it is a strong possibility that one or more magnets will be misaligned relative to the tube central axis.

Kory, Carol L.↗
NASA NTRS2000

A Reconfiguration Scheme for Accommodating Actuator Failures in Multi-Input, Multi-Output Flight Control Systems

A multi-input, multi-output reconfigurable flight control system design utilizing a robust controller and an adaptive filter is presented. The robust control design consists of a reduced-order, linear dynamic inversion controller with an outer-loop compensation matrix derived from Quantitative Feedback Theory (QFT). A principle feature of the scheme is placement of the adaptive filter in series with the QFT compensator thus exploiting the inherent robustness of the nominal flight control system in the presence of plant uncertainties. An example of the scheme is presented in a pilot-in-the-loop computer simulation using a simplified model of the lateral-directional dynamics of the NASA F18 High Angle of Attack Research Vehicle (HARV) that included nonlinear anti-wind up logic and actuator limitations. Prediction of handling qualities and pilot-induced oscillation tendencies in the presence of these nonlinearities is included in the example.

Siwakosit, W.↗
NASA NTRS1999

Direct Detection Doppler Lidar for Spaceborne Wind Measurement

The theory of double edge lidar techniques for measuring the atmospheric wind using aerosol and molecular backscatter is described. Two high spectral resolution filters with opposite slopes are located about the laser frequency for the aerosol based measurement or in the wings of the Rayleigh - Brillouin profile for the molecular measurement. This doubles the signal change per unit Doppler shift and improves the measurement accuracy by nearly a factor of 2 relative to the single edge technique. For the aerosol based measurement, the use of two high resolution edge filters reduces the effects of background, Rayleigh scattering, by as much as an order of magnitude and substantially improves the measurement accuracy. Also, we describe a method that allows the Rayleigh and aerosol components of the signal to be independently determined. A measurement accuracy of 1.2 m/s can be obtained for a signal level of 1000 detected photons which corresponds to signal levels in the boundary layer. For the molecular based measurement, we describe the use of a crossover region where the sensitivity of a molecular and aerosol-based measurement are equal. This desensitizes the molecular measurement to the effects of aerosol scattering and greatly simplifies the measurement. Simulations using a conical scanning spaceborne lidar at 355 nm give an accuracy of 2-3 m/s for altitudes of 2-15 km for a 1 km vertical resolution, a satellite altitude of 400 km, and a 200 km x 200 km spatial.

Korb, C. Laurence↗
NASA NTRS2010

High-Latitude Stratospheric Sensitivity to QBO Width in a Chemistry-Climate Model with Parameterized Ozone Chemistry

In a pair of idealized simulations with a simplified chemistry-climate model, the sensitivity of the wintertime Arctic stratosphere to variability in the width of the quasi-biennial oscillation (QBO) is assessed. The width of the QBO appears to have equal influence on the Arctic stratosphere as does the phase (i.e. the Holton-Tan mechanism). In the model, a wider QBO acts like a preferential shift toward the easterly phase of the QBO, where zonal winds at 60 N tend to be relatively weaker, while 50 hPa geopotential heights and polar ozone values tend to be higher.

Hurwitz, M. M.↗
NASA NTRS2018

Progress Towards Integrating the Finite-Volume Cubed-Sphere (FV3) Dynamical Core Tangent Linear and Adjoint Models into JEDI

The Joint Effort for Data assimilation Integration (JEDI) -- led by the Joint Center for Satellite Data Assimilation (JCSDA) -- is an inter-organizational endeavor to develop a common framework for performing data assimilation. This extensive framework will ultimately provide solvers, observation operators, interpolation and model interfaces using object oriented modeling. Two partners involved in JEDI use or plan to use the Finite Volume Cubed-Sphere (FV3) dynamical core to produce weather forecasts; these are NASA's Global Modeling and Assimilation Office and NOAA's National Center for Environment Prediction. In this work we present an update on ongoing efforts to integrate the FV3 tangent linear and adjoint models into the prototype JEDI framework. We setup and run a simple cycled data assimilation experiment using 4DVAR on the cubed sphere grid and with the FV3 tangent linear and adjoint models. Development of the observation operators for JEDI is separately underway. Instead of using real observations a simplified set of simulated observations will be used. We discuss the steps required to bring the FV3 linearized model into the object oriented framework and consider what would be the computational requirements of running this configuration for an operational system. FV3 uses a small time-step to ensure that small scales are well resolved, however this presents design challenges when running 4DVAR with the adjoint. An approach to storing the FV3 model trajectory has been developed that maintains the flexibility of using automatic differentiation. We discuss how this approach is incorporated into the framework. Other important uses of adjoint models include computing observation impacts and singular vectors, we consider how these tools can be included in JEDI.

Holdaway, Daniel↗
NASA NTRS2011

Fast Simulations of Gas Sloshing and Cold Front Formation

We present a simplified and fast method for simulating minor mergers between galaxy clusters. Instead of following the evolution of the dark matter halos directly by the N-body method, we employ a rigid potential approximation for both clusters. The simulations are run in the rest frame of the more massive cluster and account for the resulting inertial accelerations in an optimised way. We test the reliability of this method for studies of minor merger induced gas sloshing by performing a one-to-one comparison between our simulations and hydro+N-body ones. We find that the rigid potential approximation reproduces the sloshing-related features well except for two artefacts: the temperature just outside the cold fronts is slightly over-predicted, and the outward motion of the cold fronts is delayed by typically 200 Myr. We discuss reasons for both artefacts.

Roediger, E.↗
NASA NTRS2012

Fast Simulations of Gas Sloshing and Cold Front Formation

We present a simplified and fast method for simulating minor mergers between galaxy clusters. Instead of following the evolution of the dark matter halos directly by the N-body method, we employ a rigid potential approximation for both clusters. The simulations are run in the rest frame of the more massive cluster and account for the resulting inertial accelerations in an optimised way. We test the reliability of this method for studies of minor merger induced gas sloshing by performing a one-to-one comparison between our simulations and hydro+N-body ones. We find that the rigid potential approximation reproduces the sloshing-related features well except for two artifacts: the temperature just outside the cold fronts is slightly over-predicted, and the outward motion of the cold fronts is delayed by typically 200 Myr. We discuss reasons for both artifacts.

Roediger, E.↗
NASA NTRS1993

Reliability assessment of thrust chamber cooling concepts using probabilistic analysis techniques

The reliability of OFHC (Oxygen Free High Conductivity) copper and NARloy-Z thrust chambers is assessed by applying probabilistic structural analysis techniques to incorporate design parameter variability and uncertainty. Thrust chambers specifically evaluated are the cylindrical test fixtures employed in a plug-nozzle configuration at the NASA Lewis Research Center. Direct sampling Monte Carlo simulations based on a simplified life prediction methodology established probability densities of firing cycles to structural failure. Simulated cyclic lives demonstrated modest agreement to experiment. Similarly, regions of high structural failure probability were determined using a limit state approach employing calculated cumulative distribution functions for effective stress response and an assumed material strength distribution. A probability of failure of 0.012 was calculated at the center of the coolant channel hot-gas-side wall for an OFHC milled channel. Structural response was found to be sensitive to the uncertainties in the thrust chamber thermal environment and the material's thermal expansion coefficient.

Rapp, Douglas C.↗
NASA NTRS1993

Reliability assessment of thrust chamber cooling concepts using probabilistic analysis techniques

The reliability of OFHC (Oxygen Free High Conductivity) copper and NARloy-Z thrust chambers is assessed by applying probabilistic structural analysis techniques to incorporate design parameter variability and uncertainty. Thrust chambers specifically evaluated are the cylindrical test fixtures employed in a plug-nozzle configuration at the NASA Lewis Research Center. Direct sampling Monte Carlo simulations based on a simplified life prediction methodology established probability densities of firing cycles to structural failure. Simulated cyclic lives demonstrated modest agreement to experiment. Similarly, regions of high structural failure probability were determined using a limit state approach employing calculated cumulative distribution functions for effective stress response and an assumed material strength distribution. A probability of failure of 0.012 was calculated at the center of the coolant channel hot-gas-side wall for an OFHC milled channel. Structural response was found to be sensitive to the uncertainties in the thrust chamber thermal environment and the material's thermal expansion coefficient.

Rapp, Douglas C.↗
NASA NTRS2003

Validation of an In-Water, Tower-Shading Correction Scheme

Large offshore structures used for the deployment of optical instruments can significantly perturb the intensity of the light field surrounding the optical measurement point, where different portions of the visible spectrum are subject to different shadowing effects. These effects degrade the quality of the acquired optical data and can reduce the accuracy of several derived quantities, such as those obtained by applying bio-optical algorithms directly to the shadow-perturbed data. As a result, optical remote sensing calibration and validation studies can be impaired if shadowing artifacts are not fully accounted for. In this work, the general in-water shadowing problem is examined for a particular case study. Backward Monte Carlo (MC) radiative transfer computations- performed in a vertically stratified, horizontally inhomogeneous, and realistic ocean-atmosphere system are shown to accurately simulate the shadow-induced relative percent errors affecting the radiance and irradiance data profiles acquired close to an oceanographic tower. Multiparameter optical data processing has provided adequate representation of experimental uncertainties allowing consistent comparison with simulations. The more detailed simulations at the subsurface depth appear to be essentially equivalent to those obtained assuming a simplified ocean-atmosphere system, except in highly stratified waters. MC computations performed in the simplified system can be assumed, therefore, to accurately simulate the optical measurements conducted under more complex sampling conditions (i.e., within waters presenting moderate stratification at most). A previously reported correction scheme, based on the simplified MC simulations, and developed for subsurface shadow-removal processing of in-water optical data taken close to the investigated oceanographic tower, is then validated adequately under most experimental conditions. It appears feasible to generalize the present tower-specific approach to solve other optical sensor shadowing problems pertaining to differently shaped deployment platforms, and also including surrounding structures and instrument casings.

Hooker, Stanford B.↗
NASA NTRS2023

Implementing a VLBI Time Delay Model for Earth-orbiting Satellites: Partial derivatives and Verification

This document describes the partial derivatives for commonly estimated parameters including antenna positions, satellite position, and satellite velocity from a near-field VLBI delay model for Earth-orbiting satellites. This model was presented in the Journal of Geodesy by Jaron & Nothnagel (2019). In this context, we present a streamlined version of the near-field VLBI delay. From this simplified model, we deduce a delay rate expression and calculate partial derivatives, maintaining only the terms with significant impact on the computed derivatives’ magnitude. To verify the accuracy of the simplified model and the partial derivatives computed from it, we have created a simple simulation in Matlab of an Earth-orbiting satellite at the altitude of a typical Global Navigation Satellite Systems (GNSS) satellite. From this simulation, we compare the simplified and original delays, and we verify the magnitude and direction of the partial derivatives against the numerically computed derivatives from the original delay model. The partial derivatives and simplified VLBI delay model detailed here are implemented in Fortran in the open-source library VTD.

Geodesy↗
DOE OSTI2023

Coupling SCALE with DAKOTA for Axial Burnup Profiles Assessment in Burnup Credit

This paper presents a computational study that demonstrates the application of the SCALE code system in conjunction with the Design Analysis Kit for Optimization and Terascale Applications (DAKOTA) for the analysis of key factors influencing the evaluation of burnup credit (BUC) in pressurized water reactors (PWRs). The primary objective of this analysis is to characterize the model by utilizing parameterization, uncertainty quantification, and optimization studies. Using this approach, we can comprehensively assess the system and conduct informed predictive studies. This study highlights the effectiveness of the SCALE code system integrated within the DAKOTA framework in terms of efficiency and capability. With the coupling of the burnup code ORIGAMI with the CSAS or TSUNAMI-3D sequence embedded in a DAKOTA analysis, we can characterize the factors that influence the k eff of PWR 17x17 spent nuclear fuel (SNF) in the GBC-32 computational benchmark cask for the assessment of BUC in criticality safety analysis. The coupling methodology used in this study is not exclusive to BUC analysis. However, the choice to apply this methodology to the BUC problem is particularly significant because of the diverse range of aspects it encompasses in nuclear criticality safety analyses. This problem presents a unique opportunity to explore and address multiple facets of such analyses related to BUC and illustrates the capability of the SCALE code system with DAKOTA. This analysis makes use of historical reference data for the axial burnup profile, where the entire space within the bounds is considered. Both SCALE and DAKOTA are currently integrated in the Nuclear Energy Advanced Modeling Simulation (NEAMS) Workbench code system, which has a user-friendly graphical interface that simplifies the setup of simulations and configuration of input parameters as well as the visualization of simulation results.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Simplified Models of the Bicarbonate Buffer for Scaled Simulations of CO 2 Electrolyzers

Bicarbonate electrolytes are used in a range of chemical processes; however, resolved simulation of these electrolytes is difficult, as disparate reaction time scales lead to numerical stiffness and the formation of fine boundary layers. Based on several physically motivated approximations, we reduce the full set of chemical reactions within a bicarbonate electrolyte to a simpler subset, eliminating the numerical stiffness. We supported this simplification via a two-variable singular perturbation expansion and demonstrated that under neutral conditions (6 < pH < 10) typically found within a fluid-fed CO 2 electrolyzer, the simplifications lead to negligible error. Here, we also discuss two alternative simplifications, one valid at high pH and another valid at arbitrary pH. These simplifications reduce the condition number of the matrices resulting from spatiotemporal discretization by up to 10 orders of magnitude and enable three-dimensional (3D) simulation of CO 2 electrolyzers containing carbonate solutions.

10 SYNTHETIC FUELS↗
NASA NTRS1990

Bioregenerative life support

Bioregenerative life support systems utilize plant growth for food, water, and atmosphere revitalization. Simulation studies of a simplified model are presented that suggest survivability in the face of partial plant growth chamber failure. Simulation studies demonstrate the potential for a bioregenerative life support system on an extended mission. In addition to robustness and survivability in terms of the food supply, the plant growth chamber produces exactly the right amount of oxygen for the crew's metabolic needs. The amount of water taken up by the plants during food production is balanced by the crew's metabolic water production.

Taylor, Bill↗
DOE OSTI2020

Verification of an improved equation-free projective integration method for neoclassical plasma-profile evolution in tokamak geometry

A brute-force, long-time gyrokinetic simulation of plasma profile evolution in magnetic fusion devices is not desirable due to large computational resource requirements and a possible accumulation of numerical error. The equation-free projective integration method of Keverekidis et al. [Commun. Math. Sci. 1(4), 715–762 (2003)] is one of the outstanding candidates in projecting micro-scale simulations to a longer timescale. However, its application to tokamak plasma has not been fruitful due to the appearance of spurious transient oscillations in the lifting process, which are present when the kinetic simulations are initialized with a simplified model distribution function and which make the kinetic simulations to deviate from the desired paths. In this work, a kinetically informed lifting algorithm is added to the equation-free projective integration method, which is then verified in the electrostatic gyrokinetic particle-in-cell code XGCa [R. Hager and C. S. Chang, Phys. Plasmas 23, 042503 (2016)] for a neoclassical ion heat transport problem with adiabatic electrons. This new lifting operator is demonstrated to control spurious transients, enabling an over four-times reduction in the overall computing time in the time-evolution of the ion temperature profile in an axisymmetric toroidal plasma. Further reduction in the computing time is found to be limited due to the stability properties of the linear least squares projective integrator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Model-Based Framework to Optimize Charger Station Deployment for Battery Electric Vehicles

The development of battery electric vehicles (BEVs) is accelerating due to their environmental advantages over gasoline and diesel-powered vehicles, including a decrease in air pollution and an increase in energy efficiency. The deployment of charging infrastructure will need to increase to keep pace with demand, especially for large commercial vehicles for which few public chargers currently exist. In this paper, a new flexible framework is proposed for optimizing the placement of charging stations for BEVs, within which different physical models and optimization techniques may be used. Furthermore, a set of metrics is suggested to help enforce complex constraints and facilitate direct comparison between different optimization techniques. Unlike many existing charger placement techniques, the proposed method directly considers the historical driving patterns on a vehicle-by-vehicle basis, using transparent models to assess impacts of candidate charger placements, thus improving the explainability of the results. In the developed framework, modeled BEVs are first generated along the road network to mimic historical traffic data and are simulated traveling along a given route according to a simplified vehicle model. During the simulation, the charger placement problem is initially relaxed to allow vehicles to charge at any node along the road network, and vehicle states are tracked to assess areas of high charging demand. Charging stations are then placed based on the results of the relaxed simulation, and suggested placements are evaluated via road network simulation with fixed charger locations. This proposed framework is applied to a sample problem of placing charging stations along five major highway corridors for Class 8 over-the-road electric trucks. A novel mixed integer programming (MIP) formulation is proposed to optimize charger placements based upon the expected charging demand. Constraints were imposed on the final placement results to limit expected wait times at each station and ensure a minimum threshold of trucking routes are viable for BEVs. The results demonstrate the flexibility and potential effectiveness of the developed model-based framework for scalable charger station deployment.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS1989

Optical laboratory solution and error model simulation of a linear time-varying finite element equation

The use of simplified error models to accurately simulate and evaluate the performance of an optical linear-algebra processor is described. The optical architecture used to perform banded matrix-vector products is reviewed, along with a linear dynamic finite-element case study. The laboratory hardware and ac-modulation technique used are presented. The individual processor error-source models and their simulator implementation are detailed. Several significant simplifications are introduced to ease the computational requirements and complexity of the simulations. The error models are verified with a laboratory implementation of the processor, and are used to evaluate its potential performance.

Taylor, B. K.↗