Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shear modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Acoustic velocities, elasticity, and pressure-induced elastic softening in compressed neodymium

For the first time, the acoustic velocities and elasticity of double hexagonal close-packed neodymium (Nd) were measured at high pressure using ultrasonic interferometry in conjunction with synchrotron X-ray techniques. Here, both the compressional and shear wave velocities increased with an increase in pressure of up to ~5.4 GPa before they exhibited almost constant values upon further compression. This pressure-induced elastic wave velocity softening can be attributed to the structural instability in dhcp-Nd. From the current sound velocities and density data, we obtained new bulk and shear moduli as well as their pressure dependence for polycrystalline dhcp-Nd, yielding $B_0$=33.2(9) GPa, $G_0$=14.1(5) GPa, $\partial$$B/$$\partial$$P$ = 3.6 (4) and $\partial$$=G/$$\partial$$P$ = 1.3 (2) while other elasticity-related/mechanical properties, including Young's modulus, Debye temperature, Poisson's ratio, and Grüneisen parameter, which are important parameters for the application of Nd in extreme environments, were also derived.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ion Transport and Mechanical Properties of Non-Crystallizable Molecular Ionic Composite Electrolytes

Polymer electrolytes show promise as alternatives to conventional electrolytes in energy storage and conversion devices but have been limited due to their inverse correlation between ionic conductivity and modulus. In this study, we examine surface morphology, linear viscoelastic, dielectric and diffusive properties of molecular ionic composites (MICs), materials produced through the combination of a rigid and charged double helical polymer, known as poly(2,2’)-disulfonyl-4,4’benzidine terepthalamide (PBDT), with ionic liquids (ILs). To probe temperature extremes, we incorporate a non-crystallizable IL to allow measurements from to -90 to 200°C. As we increase PBDT weight percentage (wt%), shear moduli increase and do not decay up to 200°C while maintaining room temperature ionic conductivity within a factor of two of the neat IL. We connect diffusion coefficients of IL ions with ionic conductivity through the Haven ratio across a wide temperature range and analyze trends in ion transport based on a relatively high and composition-dependent static dielectric constant. This behavior may result from collective rearrangement of IL ions in these networks. We propose that these properties are driven by a two-phase system in MICs corresponding to IL-rich “puddles” and PBDT-IL associated “bundles” where IL ions form alternating sheaths of cations and anions around each PBDT rod. Furthermore, these polymer-based MIC electrolytes show great promise for use in electrochemical devices that require fast ion transport, high modulus, and a broad thermal window.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Indirectly probing the structural change in ion-irradiated Zr-Based metallic glasses from small scale mechanical tests

Ion irradiation was applied to tailor the structural heterogeneities in Zr-based metallic glasses at room temperature. Experimental methods of X-ray diffraction, nanoindentation, and micropillar compression were conducted to examine the irradiation effects on their structural and mechanical property changes. It is found that the irradiated materials retained amorphous structure after room-temperature Ni ion irradiation. The reduction of elastic modulus and hardness measured by nanoindentation indicated the irradiation-induced mechanical degradation. A unified statistic model was employed to quantitatively predict the density and strength of irradiation defects, although their specific structural and physical nature is not explicitly included in this model. The transition of non-intersecting shear bands to multiple intersecting shear bands was observed on compression tests of irradiated micropillars with the increase of irradiation dose. Furthermore, the analysis of the displacement excursion of micropillar compression tests indicated a different deformation mode from the unirradiated state. These results from nanoindentation pop-in and micro-pillar compression tests suggested that irradiation eventually leads to a new state with different types and characteristics of structural heterogeneities from violent displacement cascades and non-equilibrium energy deposition/dissipation processes, which also proves ion irradiation as an effective method to tune the structure and mechanical properties of metallic glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ductile adhesive elastomers with force-triggered ultra-high adhesion strength

Elastomers play a vital role in many forthcoming advanced technologies in which their adhesive properties determine materials’ interface performance. Despite great success in improving the adhesive properties of elastomers, permanent adhesives tend to stick to the surfaces prematurely or result in poor contact depending on the installation method. Thus, elastomers with on-demand adhesion that is not limited to being triggered by UV light or heat, which may not be practical for scenarios that do not allow an additional external source, provide a solution to various challenges in conventional adhesive elastomers. Herein, we report a novel, ready-to-use, ultra high-strength, ductile adhesive elastomer with an on-demand adhesion feature that can be easily triggered by a compression force. The precursor is mainly composed of a capsule-separated, two-component curing system. After a force-trigger and curing process, the ductile adhesive elastomer exhibits a peel strength and a lap shear strength of 1.2 × 10 4 N m -1 and 7.8 × 10 3 kPa, respectively, which exceed the reported values for advanced ductile adhesive elastomers. The ultra-high adhesion force is attributed to the excellent surface contact of the liquid-like precursor and to the high elastic modulus of the cured elastomer that is reinforced by a two-phase design. In conclusion, incorporation of such on-demand adhesion into an elastomer enables a controlled delay between installation and curing so that these can take place under their individual ideal conditions, effectively reducing the energy cost, preventing failures, and improving installation processes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rheological and Structural Properties of k‐Carrageenan/Xanthan Gum Gummies Architected With a New Natural Additive

ABSTRACT Biohybrids (BHs)based on bentonite and anthocyanins can be produced as alternatives to synthetic colorants. However, no information is available on the interaction of biohybrid with food system. This research studies the rheological properties of gummies containing k‐carrageenan and xanthan gum incorporated with a BH. The incorporation of BH (≤ 2% w/w) increased the flow consistency index and shear thinning effect in melted gummies at 85°C. During cooling from 90°C to 25°C, the presence of BH altered the sol–gel transition temperature typical in carrageenan systems, probably by the formation of carrageenan complexes. At 25°C, all gummies had a solid‐like response with elastic modulus ( G ') higher than viscous modulus ( G "). G ' values increased linearly with BH concentration, and the linear viscoelastic region and breaking strain decreased with BH concentration, indicating that this natural additive acted as a reinforcing material.

Valencia, German Ayala [Department of Chemical and↗
DOE OSTI2024

Aluminum/SmCo 5 composites for structural and magnetic applications

Metal-bonded magnetic composites (MBMCs) present a promising alternative to dense sintered magnets, particularly for intricate components. Compared to polymer-based bonded magnets, MBMCs have wider applicability in harsh environments. In this paper, we demonstrate a solid-state shear-based manufacturing technique to introduce localized magnetization into a paramagnetic aluminum matrix by embedding SmCo5 permanent magnet particles. Our magnetic composites display hard magnetic behavior with a coercivity of 13 kOe and a remanent magnetization of 4.32 emu/g. In addition to magnetization, we also report a 9% improvement in Young’s modulus. Despite the local temperature rise during processing, the magnetic phases didn’t decompose into unwanted phases, preserving the composite's hard magnetic properties. Creation of an interfacial metallurgical bond with the matrix ensured the suitability of the composites for structural applications. Our study investigates the mechanical, and functional properties of composites, paving the way for lightweight structural magnetic composites with a transformative potential in the aerospace, nuclear, and automotive applications. This work underscores the potential for further optimization and development to drive innovations in magnet and equipment design.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical performance of co-deposited immiscible Cu–Ta thin films

Abstract The immiscible alloy Cu–Ta has the potential for enhanced mechanical performance in applications as a functional coating. To establish baseline mechanical properties, four Cu–Ta films were co-sputtered at the temperatures 23, 400, 600, and 800 °C and tested with nanoindentation at strain rates 5 $$\times $$ × 10 −3 s −1 to 10 s −1 . Each film had a unique microstructure morphology. The hardness and elastic modulus of the four films were insensitive to strain rate changes. Instead, the measured properties were spatially dependent, particularly in the 600 and 800 °C films. In those two films, there is a bimodal deformation behavior due to Cu-agglomeration under protruding grains and planar Ta-rich regions. Increasing the indentation depth revealed shear band suppression which is related to a homogenous distribution of flow stresses for all four microstructure morphologies. Finally, the Cu–Ta hardness appeared to follow a rule-of-mixtures when compared to extrapolated data of Cu and Ta monolithic films.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanical properties, failure mechanisms, and scaling laws of bicontinuous nanoporous metallic glasses

Molecular dynamics simulations are employed to study the mechanical properties of nanoporous Cu x Zr 1-x metallic glasses (MGs) with five different compositions, x = 0.28, 0.36, 0.50, 0.64, and 0.72, and porosity in the range 0.1 < Φ < 0.7. Results from tensile loading simulations indicate a strong dependence of Young's modulus, E, and Ultimate Tensile Strength (UTS) on porosity and composition. By increasing the porosity from Φ = 0.1 to Φ = 0.7, the topology of the nanoporous MG shifts from closed cell to open-cell bicontinuous. The change in nanoporous topology enables a brittle-to-ductile transition in deformation and failure mechanisms from a single critical shear band to necking and rupture of ligaments. Genetic Programming (GP) is employed to find scaling laws for E and UTS as a function of porosity and composition. Here, a comparison of the GP-derived scaling laws against existing relationships shows that the GP method is able to uncover expressions that can predict accurately both the values of E and UTS in the whole range of porosity and compositions considered.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Valorization of consolidated bioprocessing residues for bioplastics

This study demonstrates an organic solvent-free processing strategy to valorize consolidated bioprocessing (CBP) residues, from switchgrass and poplar biomass, into functional poly(butylene succinate) (PBS)-based biocomposites using high-shear homogenization (HSH). HSH transformed the switchgrass and poplar CBP residues (CBP-R) into fine, uniformly distributed particles and microfibers. The composites of PBS with homogenized switchgrass residues (H-CBP-R-SG) or homogenized poplar residues (H-CBP-R-P) at a 70/30 weight ratio exhibited improved processability and mechanical integrity, with the Young's modulus for the PBS/H-CBP-R-SG and PBS/H-CBP-R-P nearly doubling to 0.66 ± 0.07 GPa and 0.65 ± 0.04 GPa, respectively, compared to neat PBS (0.36 ± 0.02 GPa). Dynamic Mechanical Analysis (DMA) reveals a significant suppression of the tan δ peak magnitude, indicating that HSH-mediated physical activation facilitates stress transfer in composites typical of covalent chemical grafting systems. While the transition to a stiffness-dominated profile reduces ductility, the resulting composites exhibit the dimensional stability and resistance to thermal warping required for high-fidelity FDM 3D printing and injection molding. Beyond material performance, comprehensive techno-economic analysis (TEA) and life cycle assessment (LCA) confirmed that diverting CBP residues into composite products can improve the economic viability of the biorefinery without substantially increasing biorefinery global warming potential (GWP). At a 30 wt% blend ratio, incorporating residuals into PBS yielded a minimum selling price for the composite of $\$4.07$ per kg compared to the conventional bioplastic price of $\$5.00$ per kg. This approach aligns with circular bioeconomy principles by converting waste streams into value-added products. Furthermore, this innovative strategy addresses key challenges in bioplastic development, including cost, compatibility, and performance, while simultaneously advancing waste minimization strategies for sustainable manufacturing systems.

09 BIOMASS FUELS↗
DOE OSTI2023

Temperature-dependent elastic constants of thorium dioxide probed using time-domain Brillouin scattering

Herein we report the adiabatic elastic constants of single-crystal thorium dioxide over a temperature range of 77–350 K. Time-domain Brillouin scattering, an all-optical, non-contact picosecond ultrasonic technique, is used to generate and detect coherent acoustic phonons that propagate in the bulk perpendicular to the surface of the crystal. These coherent acoustic lattice vibrations have been monitored in two hydrothermally grown single-crystal thorium dioxide samples along the (100) and (311) crystallographic directions. The three independent elastic constants of the cubic crystal (C 11 , C 12 , and C 44 ) are determined from the measured bulk acoustic velocities. The longitudinal wave along the (100) orientation provided a direct measurement of C 11 . Measurement of C 44 and C 12 was achieved by enhancing the intensity of quasi-shear mode in a (311) oriented crystal by adjusting the polarization angle relative to the crystal axes. We find the magnitude of softening of the three elastic constants to be ~2.5% over the measured temperature range. Good agreement is found between the measured elastic constants with previously reported values at room temperature, and between the measured temperature-dependent bulk modulus with calculated values. We find that semi-empirical models capturing lattice anharmonicity adequately reproduce the observed trend. We also determine the acoustic Grüneisen anharmonicity parameter from the experimentally derived temperature-dependent bulk modulus and previously reported temperature-dependent values of volumetric thermal expansion coefficient and heat capacity. This work presents measurements of the temperature-dependent elasticity in single-crystal thorium dioxide at cryogenic temperature and provides a basis for testing ab initio theoretical models and evaluating the impact of anharmonicity on thermophysical properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Effects of graphene surface functionalities towards controlled reinforcement of a lignin based renewable thermoplastic rubber

In this report, we describe methods to enhance mechanical properties of a renewable thermoplastic rubber by incorporating functional graphene platelets into an equal-mass mixture of lignin, a feedstock from plant biomass, and a nitrile-butadiene rubber having 41 mol % acrylonitrile content (NBR41) that form a nanocomposite. Not all lignins yield mechanically strong material when they are combined with NBR41, and thus, limit its use for such rubbery products. Here, we evaluate different graphene oxides (GO) and reduced graphene oxides (rGO) dry-powders with different surface areas, functionality, and wettability in the synthesis of performance-enhanced nanocomposites of soft lignin/NBR41 matrix via a solvent-free, high shear reactive process. High surface area GO (HSGO) platelets with strong hydrophilicity exhibit good dispersion in the multiphase lignin/NBR41 composites with lignin dispersion varying from 200 to 2000 nm, resulting in superior reinforcement over other graphene derivatives. The addition of 1–4 wt % HSGO increased the tensile stress of the lignin/NBR41 thermoplastic rubber matrix by 60–160% (15–24 MPa) and the modulus by 200–700% (60–140 MPa). Scanning electron microscopy and small angle X-ray scattering results show that the well-dispersed HSGO platelets effectively disrupt the lignin-rich aggregates in NBR41 matrix, resulting in both strength and stiffness enhancements in the formed nanocomposites. This report on performance enhancement of lignin-based renewable polymers via the production of nanocomposite would increase potential for ‘finding the value of lignin’—a grand challenge associated with modern biorefineries.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Tailoring the rheological properties of high protein suspension by thermal-mechanical treatment

The viscoelasticity of concentrated protein suspensions associates closely with the mixing efficiency and cleaning frequency of facility during high-protein food development. This study investigated the effects of thermal-mechanical treatment on the viscoelasticity of milk protein isolate (MPI) suspensions and their underlying mechanisms to develop protein ingredient with low viscoelasticity. MPI suspensions (20%) were treated at 25, 50 and 85°C for 10-60 min under constant shear (100 s -1 ), followed by storage at 4°C. The viscosity (η) of MPI suspension treated at 50°C and 85°C was similar to 1-10% as those treated at 25 ° C. After four days of storage at 4°C, η showed the least value in 50°C-treated samples compared to those at 25 ° C and 85 ° C. The η and storage modulus (G') was decreased with prolonged treatment at 25 and 50°C, whereas opposite trend was found in 85°C treated samples. Differential scanning calorimetry found proteins in 50°C treated samples had smaller enthalpy than those in the control and 25°C treated samples. Protein surface hydrophobicity was increased slightly from 25°C to 50°C, but remarkably in 85°C treated samples. Ultra-small angle x-ray scattering showed the radius of gyration (R-g) of casein micelle was similar to 38 nm at 25°C and 50°C treated samples but increased to similar to 44 nm 85°C treated samples with reduced compactness. A new sphere-like structure with R-g of 18 nm was generated in 85°C treated samples. These findings suggested modulating temperature during thermal-mechanical treatment is essential to alter protein structures and morphology for desirable rheological properties.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Impact of Backbone Rigidity on the Thermomechanical Properties of Semiconducting Polymers with Conjugation Break Spacers

There remains a lack of fundamental understanding in theroleofbackbonerigidityonthe thermomechanical properties of conjugated polymers. Here, we provide the first holistic approach to understand the fundamental influence of backbone rigidity on an n-type naphthalene diimide-based conjugated polymer, denoted by PNDI-Cx, through insertion of a flexible conjugation break spacer (CBS). CBS lengths are varied from fully conjugated with zero alkyl spacer (PNDI-C0) to a seven- carbon alkyl spacer (PNDI-C 7 ), with the CBS engineered into each repeat unit for systematic evaluation. Solution small-angle neutron scattering and oscillatory shear rheometry were employed to provide the first quantitative evidence of CBS influence over conjugated polymer chain rigidity and entanglement molecular weight (M e ), demonstrating a reduction in the Kuhn length from 521 to 36 Å for fully conjugated PNDI-C0 and PNDI-C6, respectively, as well as a nearly consistent Me of ~15 kDa upon the addition of CBS. Thermomechanical properties, such as elastic modulus and glass-transition temperature, were shown to decrease with an increasing length of CBS. An extraordinary ductility, upwards of 400% tensile strain before fracture, was observed for high-molecular-weight PNDI-C4, which we attribute to a high number of entanglements and disruption of crystallization. Furthermore, the deformation mechanism for PNDI-Cx was studied under strain through X-ray diffraction, polarized UV-vis spectroscopy, and atomic force microscopy. Overall, this work sheds light on the important role of backbone rigidity in designing flexible and stretchable conjugated polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

SMART transfer method to directly compare the mechanical response of water-supported and free-standing ultrathin polymeric films

Abstract Intrinsic mechanical properties of sub-100 nm thin films are markedly difficult to obtain, yet an ever-growing necessity for emerging fields such as soft organic electronics. To complicate matters, the interfacial contribution plays a major role in such thin films and is often unexplored despite supporting substrates being a main component in current metrologies. Here we present the shear motion assisted robust transfer technique for fabricating free-standing sub-100 nm films and measuring their inherent structural–mechanical properties. We compare these results to water-supported measurements, exploring two phenomena: 1) The influence of confinement on mechanics and 2) the role of water on the mechanical properties of hydrophobic films. Upon confinement, polystyrene films exhibit increased strain at failure, and reduced yield stress, while modulus is reduced only for the thinnest 19 nm film. Water measurements demonstrate subtle differences in mechanics which we elucidate using quartz crystal microbalance and neutron reflectometry.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of grain size on iron-boride nanoglasses

Metallic nanoglasses are made of amorphous grains that are separated by lower-density amorphous boundaries, which have been proposed to enhance plasticity through the deflection of cracks and shear bands at interfaces. It has been difficult to experimentally control grain size and interfacial structure to understand their roles in plastic deformation. Here, we fabricate bulk nanoglasses via compaction and sintering of colloidally synthesized amorphous iron-boride nanoparticles. These nanoglasses have amorphous grains with diameters from 116nm to 576nm and were tested using nanoindentation and micropillar compressions. The nanoglass with a grain size of 576 nm shows the highest elastic modulus and hardness of 101 GPa and 7.4GPa, respectively. Transmission electron microscopy reveals that nanocrystals form within the nanoglasses during compaction. Higher nanocrystal density correlates with higher nanoparticle crystallization enthalpy, an increase in plasticity, and a decrease in yield strength. Plastic strain of 5.0%, yield strength of 3.8GPa, and ultimate compressive strength of 2.7–3.8GPa were achieved. Here we show that the compaction of colloidal metallic glass nanoparticles results in robust bulk samples, with mechanical properties similar to that of other iron-based bulk metallic glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Validated Reactive Force Field Quantifies MXene Interfacial Properties, Mechanics, and Thermal Transport

MXenes combine rich surface chemistry, mechanical strength, and high conductivity for a multitude of emerging applications. Predictive modeling supports accelerated materials designs and has been limited by the absence of validated and transferable force fields. Here, we introduce an interpretable, reactive INTERFACE force field (IFF and IFF-R) for Ti 3 C 2 T x MXenes that is trained based on chemical knowledge and achieves quantitative agreement with experiments across lattice parameters (<0.5%), density (<0.2%), liquid contact angles, Raman spectra, and the in-plane elastic modulus (∼320 GPa). The models cover surface terminations from hydroxyl (−OH) to fluorine (−F) groups and are extensible to other chemistries. We introduce pH-resolved surface chemistry and identify dopamine adsorption mechanisms at MXene–aqueous interfaces supported by QCM-D and UV–Vis experiments. The data reveal coplanar and perpendicular binding modes and concentration-dependent multilayer assembly. We predict previously inaccessible properties, including termination-dependent cleavage energies, interlayer shear moduli and dynamic shear failure, nanoindentation and brittle fracture, anisotropic in-plane and out-of-plane thermal conductivities, including the role of defects. Agreement with available experimental data is consistently close and exceeds DFT accuracy across the benchmark properties examined. The IFF/IFF-R model is compatible with CHARMM, AMBER, OPLS, and CVFF force fields for simulations of MXenes with diverse surface terminations, electrolyte interfaces, biointerfaces, and polymer composites without additional parameters. Parameter sets, 3D models, and analysis scripts are provided for community use. The validated, reactive, and transferable IFF framework facilitates predictive design of MXene-based films, membranes, sensing interfaces, and composites.

MXene↗
DOE OSTI2024

Additive manufacturing of sandwich panels with continuous fiber reinforced high modulus composite facings

Abstract An improved approach consisting of a combination of fiber placement and fused filament fabrication is introduced for the additive manufacture (AM) of structural grade sandwich beams. Here, sandwich beams are additively manufactured using in‐situ deposition and consolidation of continuous fiber unidirectional facings made from a commingled yarn system of e‐glass fiber (~50% vol.) and amorphous PET, and a hexagonal honeycomb core structure made from PETG. Both facings and the sandwich core are manufactured on a single machine, in one sequence (skin‐core‐skin), employing the benefit of matrix compatibility to create autohesion at the interfaces. Flexural and transverse shear rigidity are determined experimentally and compared with analytical predictions and show correlation to within 3%. Flexural strength and core shear strength are also measured. Post‐mortem examinations show that core fracture and core facing debond were the dominant failure mode in flexure. Single cantilever beam tests were performed to evaluate core facing debond toughness. Subsequently, surface preheat using infrared heaters was utilized to increase autohesion between core and facing. The results show debond toughness was increased 4 times using infrared heating. This research effort presents a manufacturing approach that has the potential for the AM of stiff, well bonded, structural grade sandwich beams, in an integrated sequence, employing in‐situ consolidation to the facings, without the need for the use of intermediate adhesives for skin‐to‐core bonding. Highlights An improved additive manufacturing technique for making sandwich panels is developed. Sandwich panel facings have fiber volume fractions of approximately 50%. Surface preheat improves core‐to‐facing debond toughness by a factor of 4. Top and bottom facings are consolidated during manufacture leading to better properties. Experimental results are compared to analytical predictions and show good correlation.

17 WIND ENERGY↗
DOE OSTI2020

Polystyrene-block-Polydimethylsiloxane as a Potential Silica Substitute for Polysiloxane Reinforcement

We report here on microphase-separated poly(styrene-block-dimethylsiloxane) (PS-b-PDMS) as a reinforcing filler in PDMS thermosets that overcomes the long-standing problem of aging in the processing of silica-reinforced silicone. Surprisingly, PS-b-PDMS reinforced composites display comparable mechanical performance to silica-modified analogs, even though the modulus of PS is much smaller than that of silica and there is no evidence of percolation with respect to the rigid PS domains. We have found that a few unique characteristics contribute to the reinforcing performance of PS-b-PDMS. The strong self-assembly behavior promotes batch-to-batch repeatability by having well-dispersed fillers. The structure and size of the fillers depend on the loading and characteristics of both filler and matrix, along with the shear effect. The reinforcing effect of PS-b-PDMS is mostly brought by the entanglements between the corona layer of the filler and the matrix, rather than the hydrodynamic reinforcement of the PS phase.

36 MATERIALS SCIENCE↗