Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “safe mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Aeroservoelastic Wind-Tunnel Tests of a Free-Flying, Joined-Wing SensorCraft Model for Gust Load Alleviation

A team comprised of the Air Force Research Laboratory (AFRL), Boeing, and the NASA Langley Research Center conducted three aeroservoelastic wind-tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, exible vehicles. In the first of these three tests, a full-span, aeroelastically scaled, wind-tunnel model of a joined-wing SensorCraft vehicle was mounted to a force balance to acquire a basic aerodynamic data set. In the second and third tests, the same wind-tunnel model was mated to a new, two-degree-of-freedom, beam mount. This mount allowed the full-span model to translate vertically and pitch. Trimmed flight at -10% static margin and gust load alleviation were successfully demonstrated. The rigid body degrees of freedom required that the model be own in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort. The balance and free ying wind-tunnel tests will be summarized. The design of the trim and gust load alleviation control laws along with the associated results will also be discussed.

Scott, Robert C.↗
NASA NTRS2013

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression

of a two part document. Part 2 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models, Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation." A team comprised of the Air Force Research Laboratory (AFRL), Northrop Grumman, Lockheed Martin, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a semispan, aeroelastically scaled, wind tunnel model of a flying wing SensorCraft vehicle was mounted to a force balance to demonstrate gust load alleviation. In the second and third tests, the same wing was mated to a new, multi-degree of freedom, sidewall mount. This mount allowed the half-span model to translate vertically and pitch at the wing root, allowing better simulation of the full span vehicle's rigid body modes. Gust load alleviation (GLA) and Body freedom flutter (BFF) suppression were successfully demonstrated. The rigid body degrees-of-freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort.

Scott, Robert C.↗
NASA NTRS2014

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation

This is part 2 of a two part document. Part 1 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression." A team comprised of the Air Force Research Laboratory (AFRL), Boeing, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a full-span, aeroelastically scaled, wind tunnel model of a joined wing SensorCraft vehicle was mounted to a force balance to acquire a basic aerodynamic data set. In the second and third tests, the same wind tunnel model was mated to a new, two degree of freedom, beam mount. This mount allowed the full-span model to translate vertically and pitch. Trimmed flight at10 percent static margin and gust load alleviation were successfully demonstrated. The rigid body degrees of freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort. The balance and free flying wind tunnel tests will be summarized. The design of the trim and gust load alleviation control laws along with the associated results will also be discussed.

Scott, Robert C.↗
NASA NTRSDate not supplied

Design, Development, and Use of a Lunar Lander Simulation for NASA's Artemis Program

This paper describes the design, development, and initial use of a generalized and configurable lunar lander simulation to support NASA’s Artemis Program. This simulation is being developed for the Crew Compartment Office (CrewCo) in the Human Landing Systems (HLS) program and is called the HLS CrewCo Lander Simulation (HCLS). The HCLS provides insight into the challenges associated with returning humans to the Moon and the particular difficulties of operating at the Lunar South Pole. The simulation models a generalized integrated lunar landing spacecraft based on a government reference design but can and has been adapted to model vendor specific designs as well. The simulation architecture and tool sets provide a flexible framework that allows for quickly prototyping and evaluating various aspects of a piloted lunar landing system. This includes the modeling of all principal human controlled flight phases: rendezvous and docking with crew transfer systems; docked orbital outpost operations; undocking and lunar transfer; lunar orbital operations; lunar deorbit, descent, and landing (DDL); lunar surface operations; lunar ascent; and return to the orbital outpost. The flexibility of the simulation allows for the integrated evaluation of potential vehicle subsystems, crew displays, guidance and control modes, and trajectory designs. The purpose of the HCLS is not to design the ideal lunar lander, but rather to understand and the strengths and weaknesses of vehicle design choices. This paper describes the basic simulation architecture and discusses the tool sets used to develop the HCLS. This includes a number of open source tool sets and publicly available data sets. This paper also describes some of the early use cases and findings. The primary focus of early HCLS use has been on the manual piloting task to safely get the crew to the desired landing site in case of a failure in the automated guidance system. Several guidance modes and cues have been implemented which allow a pilot to manually fly the vehicle to the targeted landing site starting anywhere from powered descent initiation. It has been a valuable tool for understanding what is required to manually fly a lunar lander as well as giving a sense of the vehicle dynamics, which are much different than anything that is flown on Earth. A number of experienced test pilots have participated in manual piloting evaluations using the HCLS and provided valuable feedback on the piloting task which has been very beneficial to NASA and the HLS program.

James Michael Gentile↗
NASA NTRS1986

Solar array flight experiment

Emerging satellite designs require increasing amounts of electrical power to operate spacecraft instruments and to provide environments suitable for human habitation. In the past, electrical power was generated by covering rigid honeycomb panels with solar cells. This technology results in unacceptable weight and volume penalties when large amounts of power are required. To fill the need for large-area, lightweight solar arrays, a fabrication technique in which solar cells are attached to a copper printed circuit laminated to a plastic sheet was developed. The result is a flexible solar array with one-tenth the stowed volume and one-third the weight of comparably sized rigid arrays. An automated welding process developed to attack the cells to the printed circuit guarantees repeatable welds that are more tolerant of severe environments than conventional soldered connections. To demonstrate the flight readiness of this technology, the Solar Array Flight Experiment (SAFE) was developed and flown on the space shuttle Discovery in September 1984. The tests showed the modes and frequencies of the array to be very close to preflight predictions. Structural damping, however, was higher than anticipated. Electrical performance of the active solar panel was also tested. The flight performance and postflight data evaluation are described.

Source record↗
NASA NTRS2000

High Energy Flywheel Containment Evaluation

A flywheel testing facility is being constructed at the NASA Glenn Research Center. This facility is to be used for life cycle testing of various flywheel rotors. The lifecycle testing consists of spinning a rotor from a low rpm (approx. 20,000 ) to a high rpm (approx. 60,000) and then back to the low rpm. This spin cycle will model that which the rotor will see during use. To simulate the lifetime of the rotor, the spin cycle will be performed tens of thousands of times. A typical life cycle spin test is expected to last six months. During this time the rotor will be spun through a cycle every five minutes. The test will run continuously for the six month period barring a flywheel failure. Since it is not reasonable to have the surrounding area evacuated of personnel for the duration of the testing, the flywheel facility has to be designed to withstand a flywheel rotor failure and insure that there is no danger to any personnel in the adjacent buildings or surrounding areas. In order to determine if the facility can safely contain a flywheel rotor failure an analysis of the facility in conjunction with possible flywheel failure modes was performed. This analysis is intended as a worst case evaluation of the burst liner and vacuum tank's ability to contain a failure. The test chamber consists of a cylindrical stainless steel vacuum tank, two outer steel containment rings, and a stainless steel burst liner. The stainless steel used is annealed 302, which has an ultimate strength of 620 MPa (90,000 psi). A diagram of the vacuum tank configuration is shown. The vacuum tank and air turbine will be located below ground in a pit. The tank is secured in the pit with 0.3 m (12 in.) of cement along the base and the remaining portion of the tank is surrounded by gravel up to the access ports. A 590 kg (1300 lb.) bulkhead is placed on top of the pit during operation and the complete facility is housed within a concrete structure which has 7.5 cm (3 in.) thick walls. A cutaway of the facility is shown.

Colozza, Anthony J.↗
NASA NTRS2018

Analytical Performance, Loads, and Aeroelastic Stability of a Full-Scale Isolated Proprotor

The prediction of the performance and loads of a full-scale isolated proprotor and the calculation of whirl flutter stability of the rotor installed in a wind tunnel are considered in this study. The comprehensive analysis CAMRAD II is used. The test article is a research proprotor based on the Bell 609 rotor and the wind tunnel test apparatus is the newly developed Tiltrotor Test Rig (TTR) installed in the USAF NFAC 40- by 80-Foot Wind Tunnel. The performance and loads predictions and the stability calculations cover the following operating conditions: hover, cruise, conversion, and helicopter mode. These pre-test analytical results are being obtained to identify test operating limits, ensure a safe wind tunnel test and predict test results. Eventually, the goal is to perform a correlation study, identify shortfalls in the analytical model and introduce improvements to the analytical model. Performance and loads test results to date show that rotor torque (and yoke lag moment) may limit the test envelope. Shake test data based stability analysis shows that the TTR/609 is solidly stable within the test envelope.

Proprotor↗
NASA NTRS2003

COTS Li-Ion Cells in High Voltage Batteries

Testing at NASA JSC and COMDEV shows that Commercial Off the Shelf (COTS) Li Ion cells can not be used in high voltage batteries safely without considering the voltage stresses that may be put on the protective devices in them during failure modes.

Davies, Francis↗
NASA NTRSDate not supplied

Effect of Composite Stiffened Panel Design on Skin-Stringer Separation in Postbuckling

To design aeronautical composite multi-stringer panels that can safely operate in a postbuckled state, it is important to identify the parameters that can influence the different modes in which skin-stringer separation might occur. A methodology is under development to study the interaction between the skin-stringer separation and the postbuckling deformation. A simple criterion that can predict the initiation of skin-stringer separation is developed using the building block approach and single-stringer specimens. The criterion identifies whetherthe initiation is mainly due to bending or twisting deformations, so that these two possible modes can be studied separately. This procedure has the potential to reduce the overall development cost and allows the investigation of the design parameters that might precipitate or delay the skin-stringer separation.

Lucas J. Kootte↗
NASA NTRSDate not supplied

Effect of Composite Stiffened Panel Design on Skin-Stringer Separation in Postbuckling

To design aeronautical composite multi-stringer panels that can safely operate in a postbuckled state, it is important to identify the parameters that can influence the different modes in which skin-stringer separation might occur. A methodology is under development to study the interaction between the skin-stringer separation and the postbuckling deformation using the building block approach and single-stringer specimens. In particular, the methodology can identify whether the skin-stringer separation occurs due to bending or twisting, so that these two possible modes can be studied separately. For bending, a simple criterion that can predict the location of initiation is presented. This procedure has the potential to reduce the overall development cost and allows the investigation of the design parameters that influence the skin-stringer separation.

Lucas J. Koote↗
NASA NTRS2022

Design and Development of High-Performance Imaging Lidars for Extreme Radiation Environments of Europa

To enable safe landing on unknown terrain, such as Europa, JPL has been developing two next-generation dual-mode lidars that can provide long range altimetry as well as dense 3D mapping in real-time during landing. In this paper, we discuss the overall concept, development strategy and report on the detailed progress of the lidar development. Besides, the use for Europa, the flexible design and reconfigurability of lidars allow for a wide range of operation on other planetary bodies.

Machan, Roman↗
DOE OSTI2025

Design and Optimization of a Hybrid Design for Quantum Transduction

This study presents the mechanical design and analysis of a quantum electro-optical transducer engineered to operate at millikelvin temperatures within a dilution refrigerator. The transducer enables bidirectional microwave-optical frequency conversion through a hybrid architecture that integrates a superconducting radiofrequency (SRF) cavity with an electro-optic optical cavity. Among several design options investigated, the configuration offering the best thermal and mechanical performance was selected, yielding a robust solution with reduced sensitivity to fabrication tolerances, improved heat dissipation, as well as alignment precision. The design ensures uniform temperature distribution, enabling higher laser pump powers and, thus, increased conversion efficiency, while maintaining mechanical stresses safely below the material yield strength. Electromagnetic simulations further validate the design, demonstrating enhanced coupling between the optical and microwave modes, as well as a broader tuning range achieved with smaller tuner displacements.

quantum computing↗
NASA NTRS1989

Efficient reordering of PROLOG programs

PROLOG programs are often inefficient: execution corresponds to a depth-first traversal of an AND/OR graph; traversing subgraphs in another order can be less expensive. It is shown how the reordering of clauses within PROLOG predicates, and especially of goals within clauses, can prevent unnecessary search. The characterization and detection of restrictions on reordering is discussed. A system of calling modes for PROLOG, geared to reordering, is proposed, and ways to infer them automatically are discussed. The information needed for safe reordering is summarized, and which types can be inferred automatically and which must be provided by the user are considered. An improved method for determining a good order for the goals of PROLOG clauses is presented and used as the basis for a reordering system.

Gooley, Markian M.↗
NASA NTRSDate not supplied

Space Launch System Engine Out Capabilities

NASA's Space Launch System (SLS) is being developed with the primary purpose of returning people to the Moon and eventually landing people on Mars. With these lofty goals, ensuring mission completion is paramount even in the event of an in-flight mishap. One possible mishap is the loss of an engine in flight. While SLS was not required to show full engine out capability, the program took an ``assess to'' approach to see when the launch vehicle could complete the mission after an engine failure versus when the launch vehicle targets required a down-mode to an alternate mission target to ensure at least some flight objectives were complete, or at a minimum ensure safe return of Orion and the Crew. While this paper will focus on Artemis I, an uncrewed mission, some comparisons will be made to how the engine out capability will change for the subsequent Crewed flights of SLS and Orion.

Engine Out↗
NASA NTRSDate not supplied

Space Launch System Engine Out Capabilities

NASA's SLS is being developed with the primary purpose of returning people to the Moon and eventually landing people on Mars. With these lofty goals, ensuring mission completion is paramount even in the event of an in-flight mishap. One possible mishap is the loss of an engine in flight. While SLS was not required to show full engine out capability, the program took an ``assess to'' approach to see when the launch vehicle could complete the mission after an engine failure versus when the launch vehicle targets required a down-mode to an alternate mission target to ensure at least some flight objectives were complete, or at a minimum ensure safe return of Orion and the Crew. While this paper will focus on Artemis I, an uncrewed mission, some comparisons will be made to how the engine out capability will change for the subsequent Crewed flights of SLS and Orion.

Space Launch System↗
NASA NTRS1992

Linearized aerodynamic and control law models of the X-29A airplane and comparison with flight data

Flight control system design and analysis for aircraft rely on mathematical models of the vehicle dynamics. In addition to a six degree of freedom nonlinear simulation, the X-29A flight controls group developed a set of programs that calculate linear perturbation models throughout the X-29A flight envelope. The models include the aerodynamics as well as flight control system dynamics and were used for stability, controllability, and handling qualities analysis. These linear models were compared to flight test results to help provide a safe flight envelope expansion. A description is given of the linear models at three flight conditions and two flight control system modes. The models are presented with a level of detail that would allow the reader to reproduce the linear results if desired. Comparison between the response of the linear model and flight measured responses are presented to demonstrate the strengths and weaknesses of the linear models' ability to predict flight dynamics.

Bosworth, John T.↗
NASA NTRS2011

Performance and Life Tests of a Regenerative Blower for EVA Suit Ventilation

Ventilation fans for future space suits must meet demanding performance specifications, satisfy stringent safety requirements for operation in an oxygen atmosphere, and be able to increase output to operate in buddy mode. A regenerative blower is an attractive choice due to its ability to meet these requirements at low operating speed. This paper describes progress in the development and testing of a regenerative blower designed to meet requirements for ventilation subsystems in a future space suit Portable Life Support Systems (PLSS). The blower assembly includes a custom-designed motor that has significantly improved in efficiency during this development effort. The blower was tested at both nominal and buddy mode operating points and head/flow performance and power consumption were measured. The blower was operated for over 1000 hours to demonstrate safe operation in an oxygen test loop at prototypical pressures. In addition, the blower demonstrated operation with the introduction of simulated lunar dust.

Izenson, Mike↗
NASA NTRS1992

Telerobot control mode performance assessment

With the maturation of various developing robot control schemes, it is becoming extremely important that the technical community evaluate the performance of these various control technologies against an established baseline to determine which technology provides the most reliable robust, and safe on-orbit robot control. The Supervisory Telerobotics Laboratory (STELER) at JPL has developed a unique robot control capability which has been evaluated by the NASA technical community and found useful for augmenting both the operator interface and control of intended robotic systems on-board the Space Station. As part of the technology development and prototyping effort, the STELER team has been evaluating the performance of different control modes; namely, teleoperation under position, or rate, control, teleoperation with force reflection and shared control. Nine trained subjects were employed in the performance evaluation involving several high fidelity servicing tasks. Four types of operator performance data were collected; task completion time, average force, peak force, and number of operator successes and errors. This paper summarizes the results of this performance evaluation.

Zimmerman, Wayne↗