Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reuse”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Treatment of Produced Water from Carbon Sequestration Sites for Water Reuse and Mineral Recovery

Southern Research along with Advanced Resources International, Inc. (ARI), Heartland Technology Partners, LLC (Heartland), New Logic Research, Inc. (New Logic), and Mr. Michael N. DiFilippo, Consultant developed a concept for an on-site strategy and design for management of produced water from CO 2 sequestration sites for maximum water reuse. When CO 2 is injected into deep saline aquifers, it may be necessary to produce water from the reservoir to reduce reservoir pressure. The New Logic Research, vibratory shear enhanced process (VSEP) membrane technology, and Heartland Technology Partners, low momentum-high turbulence (LM-HT) evaporation technology was selected for evaluation for treating this produced water from a 530 MW natural gas combined cycle (NGCC) power plant by utilizing waste heat from the plant to drive the evaporation process. The technology was also evaluated for application to a coal-fired power plant in lieu of the NGCC power plant. The results from the project show that the application of the proposed technology to the 530 MW NGCC power plant scenario could be feasible. The results indicate that formation water TDS has a very large impact on the technical and economic feasibility of the process. One advantage of formations with low TDS water is that the VSEP membrane can be utilized to pre-concentrate the produced water upstream of the LM-HT. The results indicate that a significant portion of the exhaust gas from the NGCC power plant will have to be utilized to provide waste heat for the LM-HT evaporator; however, less will be required with low-TDS formation water. The CAPEX costs for LM-HT for all three formations (97.8USD to 122.7USD MM/year) and VSEP plus LM-HT (106.6USD MM/year) for the Keg River formation is high in cost but lower than all technology compared including crystallization, VSEP plus crystallization, FO plus LM-HT, VCE plus LM-HT, and VCE plus crystallization. The OPEX for the LM-HT for all three formations (6.33USD to 7.97USD MM/year) and VSEP plus LM-HT (13.29USD MM/year) for the Keg River formation is lower than crystallization, VSEP plus crystallization, FO plus LM-HT, and FO plus crystallization. Only VCE plus LM-HT and VCE plus crystallization have a comparable OPEX costs to LM-HT for all three formation and VSEP plus LM-HT for the Keg River formation. The coal-fired power plant comparison showed that it is not feasible to apply the technology to that type of fossil fuel plant.

04 OIL SHALES AND TAR SANDS↗

Evaluating Opportunities for a Circular Economy: An Investigation of Economic and Decision-Making Factors Underlying Recycling, Reusing and Remanufacturing Habits in U.S. Consumers and Manufacturers

Aluminum is increasingly used in consumer products and in lightweighting applications for airplanes, passenger cars and other vehicles. However, smelting primary aluminum is an energy-intensive process, and advanced low-energy smelting technologies have not yet been successfully scaled up to commercial production. Another way to reduce energy consumption associated with aluminum use is to increase the amount of secondary aluminum (recovered from manufacturing scrap and from recycled products) used as a raw material, thereby increasing the circularity of aluminum flows. This too has proven difficult due to the relatively low rates of recycling for most aluminum-containing products in the U.S., and the inevitable alloy mixing that occurs when end-of-life products are broken down during recycling. We previously investigated strategies for increasing secondary aluminum use, within limitations imposed by the presence of alloying elements and alloy requirements for new products. In this work, we provide context and assess the feasibility of those strategies by investigating established patterns and attitudes around recycling, remanufacturing, and other methods that promote circular material flows. Our objective is to identify technological, logistical, economic, and other barriers that exist to implementing such methods in aluminum-intensive sectors. A secondary objective is to construct a hypothetical blue-sky scenario in which aluminum use in the U.S. approaches a fully circular material flow. The blue-sky scenario allows us to identify future barriers to increasing material flow circularity and to gauge the scenario's attainability relative to current industrial practice. Our focus goes beyond recycling, in which an end-of-life product is disassembled, processed, and then separated into its component materials which serve as inputs for new products. While common in the U.S. and globally, this type of recycling involves non-trivial energy expenditures in the scrapping and processing stages and leads to impure streams of mixed secondary materials that may not be feasible or economical to use. We also consider consumer and manufacturer practices including refurbishing, remanufacturing, repair and reuse. None of these practices require that products are broken down into separate material streams before reconstitution into new products; the energy requirements are therefore lower, and the secondary components potentially easier and more economical to use. We evaluate each of these methods in terms of their economic viability for the consumer, the (re-)manufacturing firm and the scrapping and recycling firm. We also investigate barriers to and drivers of these circular practices, with particular attention paid to consumer attitudes. Initial research indicates that for consumer recycling, convenience of the recycling system is of paramount importance, with pre-existing attitudes towards recycling on a personal and community level almost as important. On the manufacturer side, a variety of logistical and economic barriers exist to instituting widespread product take-back and refurbishment programs. To better understand these barriers and how they can be overcome, we investigate several U.S. manufacturers that currently operate take-back, refurbishment and repair programs for their products, and conduct a review of similar programs in European countries where such programs are mandated by law rather than being conducted voluntarily.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Today’s Energy Challenges, Tomorrow’s Solutions: Circular Economy: Designing to Reduce, Reuse, and Upcycle

Transitioning to a Circular Economy the days of creating, using, and disposing of materials are rapidly coming to a close. This linear economy is not only inefficient and unsustainable, but the scarcity of resources we ultimately will face will make it impossible to maintain. That's why NREL is dedicating resources to research that will underpin a circular economy - designing materials with reducing, reusing, and upcycling in mind for energy-relevant and energy-intensive materials, processes, and technologies. This effort will help mitigate supply issues, promote upcycling, reduce waste, and add value to end-of-life products.

circular economy↗

Circular Economy for Energy Materials: Designing to Reduce, Reuse, and Upcycle for a More Sustainable Planet

Our global economy is on the cusp of a dramatic transformation away from a traditional linear approach - making, using, and landfill disposing of goods - to a more circular one where end of life is considered at the onset and the concepts of reducing, reusing, and chemically recycling or upcycling of goods becomes the new norm. Conventional/mechanical recycling is applicable to some materials but is underused and ineffective for a true circular economy vision. This vision ensures raw materials are used once to produce a product; and, at end of life, the product is chemically recycled back to its core building blocks to enable an infinite loop of product manufacture, use, deconstruction, and remanufacture.

CEEM↗

Preozonation of primary-treated municipal wastewater for reuse in biofuel feedstock generation

The results of a laboratory scale investigation on ozone pretreatment of primary-treated municipal wastewater for potential reuse in fermentation processes for the production of biofuels and bio-based feedstock chemicals were presented. Semi-batch preozonation with 3.0% (w/w) ozone at 1 L min -1 resulted into a considerable inactivation of the indigenous heterotrophic bacteria in the wastewater with less than 0.0002% comprising the ozone-resistant fraction of the microbial population. The disinfection process was modeled using first-order inactivation kinetics with a rate constant of 4.39 10 -3 s -1. Chemical oxygen demand (COD) levels were reduced by 30% in 1-h experiments. COD depletion was also modeled using a pseudo-first-order kinetics at a rate constant of 9.50 10 -5 s -1. Biological oxygen demand (BOD 5) values were reduced by 60% up to 20 min of ozonation followed by a plateau and some slight increases attributed to partial oxidation of recalcitrant materials. Ozone also had no substantial effect on the concentration of ammonium and phosphate ions, which are essential for microbial growth and metabolism. Preliminary tests indicated that oleaginous microorganisms could be cultivated in the ozonated wastewater, resulting in relatively higher cell densities than in raw wastewater and comparable results with autoclave-sterilized wastewater. This process could potentially produce significant quantities of oil for biofuel production from municipal wastewater streams.

biofuels, kinetics, municipal wasterwater, ozone↗

A Combined Thermochemical and Microbial Process for Recycling Polylactic Acid Polymer to Optically Pure L-Lactic Acid for Reuse

Polylactic acid polymer (PLA) produced from renewable resources can be recycled at the end of life to constituent monomer, optically pure lactic acid (LA), by a combination of chemical and biological processes. Efficient application of this closed loop of LA-PLA plastics-LA can minimize accumulation of plastics waste that pollute land and oceans. Temperature-dependent hydrolysis of PLA in water to LA follows apparent first order decay kinetics after a short lag. A modified Gompertz equation can explain the overall hydrolysis process. Alkali increased the rate of hydrolysis of PLA and reduced the length of lag period compared to water alone. The stoichiometry of base added to LA released was 1.0. The highest lactic acid yield was 0.95 g g -1 of PLA. D-LA in the syrup obtained after hydrolysis of PLA-plastics was removed using an engineered Escherichia coli to produce a L-LA syrup with an optical purity ≥ 99%. Here, these results show that thermochemical hydrolysis of PLA-based plastics to LA with optimum amount of base followed by bio-based purification to L-LA is an effective method of recycling PLA-plastics for reuse.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Throughput Statistical Interrogation of Mechanical Properties with Build Plate Location and Powder Reuse in AlSi10Mg

Abstract Additive manufacturing (AM) allows agile, rapid manufacturing of geometrically complex components that would otherwise be impossible through traditional manufacturing methods. With this maturing manufacturing technology comes the need to adopt testing methods that are commensurate with the speed of additive manufacturing and take advantage of its geometric flexibility. High-throughput tensile testing (HTT) is a technique that allows a large number of tensile bars to be tested in a short amount of time. In the present study, HTT is used to evaluate AM AlSi10Mg produced using powder bed fusion with a Renishaw AM250 machine. Three parameters were varied in this study: (1) powder reuse history, (2) location on the build plate, and (3) size of the tensile specimen. For all parameter combinations, at least 22 specimens were tested; in several cases, over 40 were tested. This large dataset, consisting of over 500 tensile tests, permits Weibull statistical analysis and provides sufficient fidelity to isolate subtle trends that would have likely been missed in smaller, traditional datasets. The observed trends are rationalized in terms of the role of porosity and surface crust on mechanical response.

Carroll, Jay D. (ORCID:0000000258184709)↗

Standardization Gaps in Powder Feedstock Characterization and Establishing Acceptability for Reuse in Additive Manufacturing

Characterization techniques for powder feedstocks used in additive manufacturing (AM) have long been relied upon to describe the inputs to an AM workflow. However, functional gaps remain between tests to measure intrinsic and extrinsic properties with the direct performance within AM equipment. Furthermore, the common practice of reusing powder through multiple build cycles introduces effects and changes to feedstock performance that are otherwise difficult to measure quantitatively. Here, standardization and the development of new test methods have not kept pace with the rapid evolution of the AM industry and its reliance on highly coupled process-structure–property-performance relationships.

Characterization and Analytical Technique↗

Highly crystalline, low-ash, graphite from coal using an Fe 2 O 3 -based catalytic process with recovery and reuse of catalyst and process acid

This study presents a sustainable process for producing highly crystalline, low-ash graphite from sub-bituminous coal using an Fe 2 O 3 -based catalytic method. The process integrates coal mineral removal, catalyst regeneration, and reagent recycling into a closed-loop system. Acid-soluble Fe-residue and mineral impurities are eliminated from the solid graphite through HCl treatment, followed by hydrolytic distillation to regenerate Fe 2 O 3 and recover HCl for reuse. Coal-derived silica is removed with a KOH rinse, yielding low-ash graphite suitable for high-performance applications. The closed-loop catalytic graphitization, where the recovered Fe 2 O 3 and HCl are used in subsequent graphitization runs, produces graphite with a degree of graphitization exceeding 95%. The L a and L c crystallite sizes reach 65–78 nm and 44–48 nm, respectively, with BET surface areas of 4–10 m 2 /g and an ash content below 0.1 wt.%. Lithium-ion battery testing reveals that anodes fabricated with this graphite deliver an initial discharge capacity between 384.5 and 421.2 mAh/g, averaging 395.0 ± 19.1 mAh/g, along with initial coulombic efficiencies of 85.0–89.1%. After 100 discharge–charge cycles at 0.25C, reversible capacities remain between 358.8 and 369.7 mAh/g, while coulombic efficiency stays above 99.9%. The findings highlight that coal can serve as a viable precursor for high-quality graphite production under relatively mild conditions, avoiding the need for extreme temperatures or aggressive reagents such as hydrofluoric acid, commonly employed in conventional processes. This work demonstrates both technical feasibility and environmental benefits, emphasizing its potential to support large-scale, sustainable graphite production for applications such as lithium-ion batteries.

Catalytic graphitization↗

Direct reuse of graphite and lithium nickel manganese cobalt oxide (NMC) recovered from ultrafast-laser ablation debris in Li-ion battery electrodes

Here we demonstrate that debris collected from the ultrafast-laser ablation of graphite anodes can be directly reused in a lithium-ion battery with little to no negative effects on electrochemical performance. Further, we show that while post-ablation NMC (LiNi 0.33 Mn 0.33 Co 0.33 O) cathode debris will require additional processing before being incorporated into an electrode, its critical materials (nickel, manganese, and cobalt) are not lost during ablation and can be recovered for recycling. Pre- and post-ablation materials are characterized with a suite of diagnostics, including SEM, TEM, X-ray CT, EDS, and XRD, to study changes in material morphology, composition and crystal structure. Graphite exhibited little to no morphological or compositional changes and a slight annealing of its crystal structure. NMC underwent profound morphological and crystallographic changes, but retained its elemental composition. Finally, post-ablation materials were re-manufactured into electrodes and cycled vs lithium metal. Graphite showed equal or better capacity and Coulombic efficiency compared to pre-ablation electrodes, while the post-ablation NMC exhibited severely reduced electrochemical performance. Furthermore, we discuss the outlook for application of this work to advanced manufacturing lines that produce next-generation, laser-patterned electrodes.

25 ENERGY STORAGE↗

Reuse of secondhand TVs exported from Japan to the Philippines

The trade of secondhand electrical and electronic equipment (EEE) from developed to developing countries has become a growing environmental issue owing to concerns about improper recycling of these goods in developing countries. We followed a 12-m cargo container of cathode-ray-tube color TVs exported from Japan to the Philippines in February 2008. We surveyed the number of TVs damaged in transport, as well as the number of malfunctioning TVs from this shipment. In addition, we present the results of interviews with 113 Filipino consumers who intended to buy secondhand EEE at nine secondhand shops in Metro Manila. Approximately 3% of the imported TVs were damaged upon arrival. The importer sold some of the units directly to local dealers, and kept the rest to repair, refurbish and resell. Approximately 40% of the imported TVs malfunctioned and needed repair in addition to basic reconditioning. Most interviewees indicated that they prefer to buy secondhand EEE because the prices are lower than those of brand-new products. Consumers indicated that they planned on using the product for an average of about 5 years, but the actual period of use may be lower. Most end-of-life EEE in the Philippines is dismantled and recycled by unregulated companies and untrained individuals in markets or near landfill sites, and it is clear that a proper collection system and treatment methods are needed for e-waste. In addition to the material flow of secondhand TVs, we also discuss several economic aspects and appropriate control measures of the international reuse of secondhand TVs.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Can N95 Respirators Be Reused after Disinfection? How Many Times?

The coronavirus disease 2019 (COVID-19) pandemic has led to a major shortage of N95 respirators, which are essential for protecting healthcare professionals and the general public who may come into contact with the virus. Thus, it is essential to determine how we can reuse respirators and other personal protective equipment in these urgent times. We investigated multiple commonly used disinfection schemes on media with particle filtration efficiency of 95%. Heating was recently found to inactivate the virus in solution within 5 min at 70 °C and is among the most scalable, user-friendly methods for viral disinfection. We found that heat (≤85 °C) under various humidities (≤100% relative humidity, RH) was the most promising, nondestructive method for the preservation of filtration properties in meltblown fabrics as well as N95-grade respirators. At 85 °C, 30% RH, we were able to perform 50 cycles of heat treatment without significant changes in the filtration efficiency. At low humidity or dry conditions, temperatures up to 100 °C were not found to alter the filtration efficiency significantly within 20 cycles of treatment. Ultraviolet (UV) irradiation was a secondary choice, which was able to withstand 10 cycles of treatment and showed small degradation by 20 cycles. However, UV can potentially impact the material strength and subsequent sealing of respirators. Finally, treatments involving liquids and vapors require caution, as steam, alcohol, and household bleach all may lead to degradation of the filtration efficiency, leaving the user vulnerable to the viral aerosols.

60 APPLIED LIFE SCIENCES↗

Cyanobacterial reuse of extracellular organic carbon in microbial mats

Cyanobacterial organic matter excretion is crucial to carbon cycling in many microbial communities, but the nature and bioavailability of this C depend on unknown physiological functions. Cyanobacteria-dominated hypersaline laminated mats are a useful model ecosystem for the study of C flow in complex communities, as they use photosynthesis to sustain a more or less closed system. Although such mats have a large C reservoir in the extracellular polymeric substances (EPSs), the production and degradation of organic carbon is not well defined. To identify extracellular processes in cyanobacterial mats, we examined mats collected from Elkhorn Slough (ES) at Monterey Bay, California, for glycosyl and protein composition of the EPS. We found a prevalence of simple glucose polysaccharides containing either α or β (1,4) linkages, indicating distinct sources of glucose with differing enzymatic accessibility. Using proteomics, we identified cyanobacterial extracellular enzymes, and also detected activities that indicate a capacity for EPS degradation. In a less complex system, we characterized the EPS of a cyanobacterial isolate from ES, ESFC-1, and found the extracellular composition of biofilms produced by this unicyanobacterial culture were similar to that of natural mats. By tracing isotopically labeled EPS into single cells of ESFC-1, we demonstrated rapid incorporation of extracellular-derived carbon. Taken together, these results indicate cyanobacteria reuse excess organic carbon, constituting a dynamic pool of extracellular resources in these mats.

Environmental Sciences & Ecology↗

REMBI: Recommended Metadata for Biological Images—enabling reuse of microscopy data in biology

Bioimaging data have significant potential for reuse, but unlocking this potential requires systematic archiving of data and metadata in public databases. Here, we propose draft metadata guidelines to begin addressing the needs of diverse communities within light and electron microscopy. We hope this publication and the proposed Recommended Metadata for Biological Images (REMBI) will stimulate discussions about their implementation and future extension.

59 BASIC BIOLOGICAL SCIENCES↗

Extraction, purification, and reuse of dyes from coloured polyester textiles

The removal of dyes from coloured textile waste represents a sustainable approach to textile recycling, enabling the recovery of valuable chemical, and material resources that would otherwise be discarded. Up to 40% of the greenhouse gas emissions from textiles originate from dye production, making efficient recycling of dyes a major opportunity for curbing emissions and minimizing waste in both textile manufacturing and recycling. Here, in this study, we demonstrate a process for the extraction, purification, and reuse of mixed dyes from polyester textiles using bio-based, non-hazardous solvents selected on the basis of computational predictions for polyester and dye solubilities. Extracted dyes are purified to individual compounds using counter-current chromatography and analysed via liquid chromatography-mass spectrometry. Post-extraction characterization of the extracted dyes and polymer substrate confirms dye colour retention and polyester fabric property preservation. Dye recycling is demonstrated by redyeing colour-free fabrics with the recovered dyes. We further show a potential process configuration for dye removal using a flow-through reactor packed with a textile substrate. The proposed dye removal process produces reusable, recyclable dyes, and dye-free fabrics, thus facilitating textile recycling.

36 MATERIALS SCIENCE↗

Increasing resilience with wastewater reuse

Drinking water infrastructure in urban settings is increasingly affected by population growth and disruptions like extreme weather events. This study explores how the integration of direct wastewater reuse can help to maintain drinking water service when the system is compromised.

54 ENVIRONMENTAL SCIENCES↗