Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “process development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Developing processing techniques for Skylab data

The author has identified the following significant results. An analysis of the conic data was completed for the spatial misregistration study. The effects of misregistration on classification and acreage estimation accuracy are being studied. Signatures were extracted for the primary ground covers in the test area.

Nalepka, R. F.↗
NASA NTRS1976

Fabrication process development of SiC/superalloy composite sheet for exhaust system components

A chemical compatibility study was conducted between SiC filament and the following P/M matrix alloys: Waspaloy, Hastelloy-X, NiCrAlY, Ha-188, S-57, FeCrAlY, and Incoloy 800. None of the couples demonstrated sufficient chemical compatibility to withstand the minimum HIP consolidation temperatures (996 C) or intended application temperature of the composite (982 C). However, Waspaloy, Haynes 188, and Hastelloy-X were the least reactive with SiC of the candidate alloys. Chemical vapor deposited tungsten was shown to be an effective diffusion barrier between the superalloy matrix and SiC filament providing a defect-free coating of sufficient thickness. However, the coating breaks down when the tungsten is converted into intermetallic compounds by interdiffusion with matrix constituents. Waspaloy was demonstrated to be the most effective matrix alloy candidate in contact with the CVD tungsten barrier because of its relatively low growth rate constant of the intermediate compound and the lack of formation of Kirkendall voids at the matrix-barrier interface. Fabrication methods were developed for producing panels of uniaxial and angle ply composites utilizing CVD tungsten coated filament.

Cornie, J. A.↗
NASA NTRS1978

Silicon Web Process Development

Progress in the development of techniques to grow silicon web at 25 wq cm/min output rate is reported. Feasibility of web growth with simultaneous melt replenishment is discussed. Other factors covered include: (1) tests of aftertrimmers to improve web width; (2) evaluation of growth lid designs to raise speed and output rate; (3) tests of melt replenishment hardware; and (4) investigation of directed gas flow systems to control unwanted oxide deposition in the system and to improve convective cooling of the web. Compatibility with sufficient solar cell performance is emphasized.

Duncan, C. S.↗
NASA NTRS1979

LSA Large Area Silicon Sheet Task Continuous Czochralski Process Development

A commercial Czochralski crystal growing furnace was converted to a continuous growth facility by installation of a small, in-situ premelter with attendant silicon storage and transport mechanisms. Using a vertical, cylindrical graphite heater containing a small fused quartz test tube linear from which the molten silicon flowed out the bottom, approximately 83 cm of nominal 5 cm diamter crystal was grown with continuous melt addition furnished by the test tube premelter. High perfection crystal was not obtained, however, due primarily to particulate contamination of the melt. A major contributor to the particulate problem was severe silicon oxide buildup on the premelter which would ultimately drop into the primary melt. Elimination of this oxide buildup will require extensive study and experimentation and the ultimate success of continuous Czochralski depends on a successful solution to this problem. Economically, the continuous Czochralski meets near-term cost goals for silicon sheet material.

Rea, S. N.↗
NASA NTRS1979

Silicon Solar Cell Process Development, Fabrication and Analysis

The standard solar cells (2x2 cm) from the cast silicon (HEM) showed a maximum AMO efficiency of 10.1%. Cells from the low resistivity material (0.5 ohm-cm) showed lower performance than those of the high resistivity cast silicon (3 ohm-cm), an average efficiency 9.5% versus 7.6%. Maximum AMO efficiency of the standard solar cells from the EFG (RH) ribbons was about 7.5%. The solar cells from the controlled SiC, using the displaced die, showed more consistent and better performance than those of the uncontrolled SiC ribbons, an average efficiency of 6.6% versus 5.4%. The average AMO efficiency of the standard SOC solar cells were about 6%. These were large area solar cells (an average area of 15 sq cm). A maximum efficiency of 7.3% was obtained. The SOC solar cells showed both leakage and series resistance problems, leading to an average curve fill factor of about 60%.

Yoo, H. I.↗
NASA NTRS1979

Silicon Solar Cell Process Development, Fabrication and Analysis

The standard solar cells (2x2 cm) from the cast silicon heatexchanger method) showed a maximum AMO efficiency of 10.1%. Cells from low resistivity material (0.5 ohm-cm) showed lower performance than those of the high resistivity cast silicon (3 ohm-cm), an average efficiency 9.5% versus 7.6% Maximum AMO efficiency of the standard solar cells (2x2 cm) from the EFG (RH) ribbons was about 7.5%. The solar cells from controlled SiC, using the displaced die, showed more consistent and better performance than those of the uncontrolled SiC ribbons, an average efficiency of 6.6% versus 5.4% The average AMO efficiency of the standard silicon ceramic (soc) solar calls were about 6%. These were large area solar cells (an average area of 15 sq cm). A maximum efficiency of 7.3% was obtained. The SOC solar cells showed both leakage and series resistance problems, leading to an average curve fill factor of about 60%.

Yoo, H. I.↗
NASA NTRS1979

Silicon web process development

Silicon dendritic web, a single crystal ribbon shaped during growth by crystallographic forces and surface tension (rather than dies), is a highly promising base material for efficient low cost solar cells. The form of the product smooth, flexible strips 100 to 200 microns thick, conserves expensive silicon and facilitates automation of crystal growth and the subsequent manufacturing of solar cells. These characteristics, coupled with the highest demonstrated ribbon solar cell efficiency-15.5%-make silicon web a leading candidate to achieve, or better, the 1986 Low Cost Solar Array (LSA) Project cost objective of 50 cents per peak watt of photovoltaic output power. The main objective of the Web Program, technology development to significantly increase web output rate, and to show the feasibility for simultaneous melt replenishment and growth, have largely been accomplished. Recently, web output rates of 23.6 sq cm/min, nearly three times the 8 sq cm/min maximum rate of a year ago, were achieved. Webs 4 cm wide or greater were grown on a number of occassions.

Duncan, C. S.↗