Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer mechanics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mechanical and physical properties of inorganic polymer cement made of iron-rich laterite and lateritic clay: A comparative study

In this work, two different laterites (iron contents of 13.07 and 49.34 wt%, respectively, for lateritic clay, LAC, and iron-rich laterite, LAI) were selected and calcined at 600 °C. The obtained calcined laterites, namely LAI600 and LAC600, were separately mixed with an alkaline solution (silicate modulus of 1.35) or an acidic solution (phosphoric acid solution at pH ≤ 2) for the synthesis of inorganic polymer products. The fabricated products were cured at 20 °C (ambient) and 40 °C (oven). The obtained results showed that the compressive strength of each series of alkaline-based inorganic polymer binder increased with ageing time (7 and 28 days) for room temperature curing, while the reverse trend was noted for oven-cured specimens. The best mechanical performance was obtained when using a phosphoric acid solution, 38 and 52 ± 1 MPa; 62 and 65 ± 1 MPa at 28 days for LAC and LAI respectively. It appeared that a higher iron content within the laterite contributed to an increase in the compressive strength under acidic conditions (LAI (59 MPa) > LAC (48 MPa)) compared to the behavior obtained under alkaline conditions (LAI (6 MPa) < LAC (29 MPa)). Accordingly, the acidic products exhibited a dense structure (with lower porosity) and contained amorphous iron/aluminium phosphate phases such as berlinite (FePO{sub 4}), iron hydrogen phosphate hydrate (Fe{sub 3}H{sub 15}(PO{sub 4}){sub 8·}4H{sub 2}O), ferrowyllieite (AlFe{sub 2}Na{sub 2}(PO{sub 4}){sub 3}) and sodium iron phosphate (Na{sub 3}Fe{sub 2}(PO{sub 4}){sub 3}) arising from the alteration of iron minerals in an acidic medium, confirmed by Mössbauer spectroscopy and electron paramagnetic resonance spectroscopy.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Mechanics of Nanotubes and Nanotube-Polymer Composites

CNT is a tubular form of carbon with diameter as small as 1 nm. Length: few nm to microns. CNT is configurationally equivalent to a two dimensional graphene sheet rolled into a tube. CNT exhibits extraordinary mechanical properties: Young's modulus over 1 Tera Pascal, as stiff as diamond, and tensile strength approx. 200 GPa. CNT can be metallic or semiconducting, depending on chirality.

Srivastava, Deepak↗
DOE OSTI2022

A Micro-Mechanical Constitutive Model to Predict Hygrothermal Aging of Cross-Linked Polymers

Abstract A multi-physics material model is presented to describe the effects of temperature, oxygen, and humidity on the constitutive response of cross-linked polymers. The effect of hygrothermal damage on the mechanical integrity of the polymer matrix can be considered as the result of damage accumulation of two independent aging mechanism namely, i) thermo-oxidative, and ii) hydrolytic aging. In order to capture the mutual effects of thermo-oxidative and hydrolytic aging, an assumption has been made that each of the aging phenomenon can be superposed to each other. In fact, each of them works independently and as a result, they can compete with each other. Utilizing the theory of network decomposition, all phenomena and their correlation were modeled and thus, the strain energy function of the polymer matrix is written with respect to four independent mechanisms, i) the shrinking original matrix that has neither been attacked by water nor oxygen, ii) conversion of the first network to two new network due to the reduction and formation of cross-links, and iii) energy loss from network degradation due to attack of the water molecules to polymer active agents. Moreover, the proposed model is micro-mechanically based and is mainly relevant on thin samples due to our underlying assumption of homogeneous diffusion of oxygen and water throughout the matrix. The model has been validated against extensive data-sets obtained from experiments we specifically designed for concept validation.

Bahrololoumi, Amir↗
DOE OSTI2026

Relief Zones Enhance the Durability of Ultrathin Membranes in Electrochemical Conversion Devices

Premature failures in electrochemical conversion systems often result when membrane electrode assemblies (MEAs) use ultrathin (≤15 μm-thick) polymer electrolyte membranes, susceptible to mechanical degradation from stress concentrations arising from device-level integration. Herein, relief zones were developed to mitigate mechanical degradation by alleviating excess and nonuniform compression across active areas. Relief zones, created through ablation of carbonaceous diffusion media, enable seamless adaptation across MEA dimensions without need for hardware modifications. Demonstrated using fuel cells as a case study, accelerated stress tests revealed a 6-fold lifetime improvement (∼1500 h) compared to conventional edge-protected MEAs, decoupling device-level engineering effects from material limitations.

accelerated stress test↗
DOE OSTI2026

Stereochemically‐Controlled Fluorinated Copolymers for Selectively Permeable Barrier Applications

Selective oxygen permeability coupled with low water vapor transmission is essential for biomedical and packaging applications requiring controlled oxygen flux under humid conditions. However, most high‐performance barrier polymers depend on perfluoroalkyl substances (PFAS), whose persistence and regulatory restrictions limit their long‐term applicability. We designed a series of stereocontrolled thiol‐yne‐based polyesters, including both fluorinated and non‐fluorinated variants, for selective oxygen permeability with considerable water barrier performance. Tailoring polymer crystallinity and morphology tuned both oxygen transport and mechanical properties. Fluorinated polymers demonstrated enhanced hydrophobicity and water resistance while maintaining oxygen diffusivity within a range relevant to oxygen‐sensing applications. Structure–property relationships were elucidated through small‐ and wide‐angle X‐ray scattering, revealing semi‐crystalline domains influenced by fluorine content and dithiol chain length. Barrier performance was rigorously evaluated via water vapor transmission rate and dynamic vapor sorption, showing reduced water uptake with increasing dithiol monomer length and crystallinity. In conclusion, this work introduces a PFAS‐free alternative to conventional barrier materials and establishes a tunable materials platform with potential relevance for biomedical devices and packaging systems requiring controlled oxygen permeability.

36 MATERIALS SCIENCE↗
NASA NTRS2012

Nanostructured Solar Irradiation Control Materials for Solar Energy Conversion

Tailoring the solar absorptivity (alpha(sub s)) and thermal emissivity (epsilon(sub T)) of materials constitutes an innovative approach to solar energy control and energy conversion. Numerous ceramic and metallic materials are currently available for solar absorbance/thermal emittance control. However, conventional metal oxides and dielectric/metal/dielectric multi-coatings have limited utility due to residual shear stresses resulting from the different coefficient of thermal expansion of the layered materials. This research presents an alternate approach based on nanoparticle-filled polymers to afford mechanically durable solar-absorptive and thermally-emissive polymer nanocomposites. The alpha(sub s) and epsilon(sub T) were measured with various nano inclusions, such as carbon nanophase particles (CNPs), at different concentrations. Research has shown that adding only 5 wt% CNPs increased the alpha(sub s) and epsilon(sub T) by a factor of about 47 and 2, respectively, compared to the pristine polymer. The effect of solar irradiation control of the nanocomposite on solar energy conversion was studied. The solar irradiation control coatings increased the power generation of solar thermoelectric cells by more than 380% compared to that of a control power cell without solar irradiation control coatings.

Kang, Jinho↗
DOE OSTI2022

Polymers and methods for their manufacture

Embodiments of the invention relate to a novel class of polymers with superior mechanical properties and chemical stability, as compared to known polymers. These polymers are particularly well suited for use in anion exchange membranes (AEMs), including those employed in fuel cells. Novel methods for the manufacture of these polymers are also described.

Bae, Chulsung↗
DOE OSTI2022

Polymers and methods for their manufacture

Embodiments of the invention relate to a novel class of polymers with superior mechanical properties and chemical stability, as compared to known polymers. These polymers are particularly well suited for use in anion exchange membranes (AEMs), including those employed in fuel cells. Novel methods for the manufacture of these polymers are also described.

Bae, Chulsung↗
DOE OSTI2023

Polymers and methods for their manufacture

Embodiments of the invention relate to a novel class of polymers with superior mechanical properties and chemical stability, as compared to known polymers. These polymers are particularly well suited for use in anion exchange membranes (AEMs), including those employed in fuel cells. Novel methods for the manufacture of these polymers are also described.

Bae, Chulsung↗
DOE OSTI2020

3D Ion-Conducting, Scalable, and Mechanically Reinforced Ceramic Film for High Voltage Solid-State Batteries

Concerning the safety aspects of Li+ ion batteries, an epoxy-reinforced thin ceramic film (ERTCF) is prepared by firing and sintering a slurry-casted composite powder film. The ERTCF is composed of Li + ion conduction channels and is made of high amounts of sintered ceramic Li 1+ x Ti 2-x Al x (PO 4 ) 3 (LATP) and epoxy polymer with enhanced mechanical properties for solid-state batteries. The two- and three-dimensional characterizations are conducted not only for showing continuous Li+ ion channels thorough LATP ceramic channels with over 10-4 S cm-1 of ionic conductivity but also to investigate small amounts of epoxy polymer with enhanced mechanical properties. Solid-state Li + ion cells are fabricated using the ERTCF and they show initial charge–discharge capacities of 139/133 mAh g -1 . Furthermore, the scope of the ERTCF is expanded to high-voltage (>8 V) solid-state Li + ion batteries through a bipolar stacked cell design. Hence, it is expected that the present investigation will significantly contribute in the preparation of the next generation reinforced thin ceramic film electrolytes for high-voltage solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Constitutive Modeling of the Cross-Linked Polymers During the Trio-Aging Mechanism: Effects of Water, Oxygen, UV

Abstract The synergized effects of diverse environmental conditions such as humidity, temperature, UV, and oxygen, are considered through a generic model by combining the concepts of network alteration, hygrothermal, and Photo-thermo oxidation Models [1–4]. Hygrothermal and Photo-oxidation are considered dual aging mechanisms which are due to the synergized effects of moisture-oxygen, and UV-oxygen, respectively at elevated temperatures. Here Trio-aging is considered as the synergized effects of Hygrothermal, and Photo-oxidation which the main environmental elements involved in polymer degradation are oxygen, water, and UV radiation where each of which has a different micro-structural impact on the polymer matrix. While oxygen imposes chain scission and cross-link formation, water, and UV radiation mainly cause chain scission. Similar to our recent models, the dual network hypothesis of Topolosky is utilized and as a result, the strain energy of the polymer matrix is written in terms of two states namely unaged and infinity. The infinity state network, itself, is decomposed into three networks, namely brittle, flexible, and dead networks. While the brittle network models the cross-link formation as sub-structural phenomena, the flexible and dead networks are utilized to represent the cross-link reduction and chain scission. The contribution of these networks in the infinity state is based on the amount of relevant environmental elements. The model is developed for a domain with plenty of oxygen and holds true for a gradual aging process that happens in super-thin samples.

Bahrololoumi, Amir↗
NASA NTRS2004

Mechanically Strong Aerogels Formed by Templated Growth of Polymer Cross- Linkers on Inorganic Nanoparticles

In the search for materials with better mechanical, thermal, and electrical properties, it is becoming evident that oftentimes dispersing ceramic nanoparticles in plastics improves performance. Along these lines, chemical bonding (both covalent and noncovalent) between a filler and a polymer improves their compatibility, and thus enhances certain properties of the polymeric matrix above and beyond what is accomplished by simple doping with the filler. When a similarly sized dopant and matrix are used, elementary building blocks may also have certain distinct advantages (e.g., in catalysis). In this context, researchers at the NASA Glenn Research Center reasoned that in the extreme case, where the dopant and the matrix (e.g., a filler and a polymer) are not only sized similarly, but their relative amounts are comparable, the relative roles of the dopant and matrix can be reversed. Then, if the "filler," or a certain form thereof, possesses desirable properties of its own, such properties could be magnified by cross-linking with a polymer. We at Glenn have identified silica as such a filler in its lowest-density form, namely the silica aerogel.

Leventis, Nicholas↗
NASA NTRS1996

Effect of Cyclic Thermo-Mechanical Loads on Fatigue Reliability in Polymer Matrix Composites

A methodology to compute probabilistic fatigue life of polymer matrix laminated composites has been developed and demonstrated. Matrix degradation effects caused by long term environmental exposure and mechanical/thermal cyclic loads are accounted for in the simulation process. A unified time-temperature-stress dependent multi-factor interaction relationship developed at NASA Lewis Research Center has been used to model the degradation/aging of material properties due to cyclic loads. The fast probability integration method is used to compute probabilistic distribution of response. Sensitivities of fatigue life reliability to uncertainties in the primitive random variables (e.g., constituent properties, fiber volume ratio, void volume ratio, ply thickness, etc.) computed and their significance in the reliability- based design for maximum life is discussed. The effect of variation in the thermal cyclic loads on the fatigue reliability for a (0/+/- 45/90)(sub s) graphite/epoxy laminate with a ply thickness of 0.127 mm, with respect to impending failure modes has been studied. The results show that, at low mechanical cyclic loads and low thermal cyclic amplitudes, fatigue life for 0.999 reliability is most sensitive to matrix compressive strength, matrix modulus, thermal expansion coefficient, and ply thickness. Whereas at high mechanical cyclic loads and high thermal cyclic amplitudes, fatigue life at 0.999 reliability is more sensitive to the shear strength of matrix, longitudinal fiber modulus, matrix modulus, and ply thickness.

Shah, A. R.↗
DOE OSTI2025

How Topological Polymer Loops on the Nanoparticle Surface Control the Mechanical Properties of Nanocomposites

Carbon black (CB) and silica (SiO 2 ) filled elastomers are known to be the most successful polymer nanocomposites (PNCs) in industry, where “bound rubber (BR)” (i.e., polymer chains that are physically or chemically adsorbed on the nanofiller surface) plays a critical role in their reinforcement. Here, we report a molecular-scale mechanism underlying the “BR-induced reinforcement” by integrating neutron scattering experiments and molecular dynamics simulations. Simplified non-cross-linked SiO 2 -filled polybutadiene (PB) and CB-filled PB reveal the critical role of topological polymer loops in the BR for the enhanced mechanical performance. The average loop size on the SiO 2 surface modified with a silane coupling agent is much smaller than that on the CB surface and the loops on the SiO 2 surface are densely formed, preventing interdigitation with the matrix chains. On the other hand, the larger, uncrowded loops formed on the CB surface facilitate the interdigitation with the matrix polymer chains even near the filler surface. In this way, a strong connectivity is established between a matrix and a nanofiller, resulting in an adhesive filler–polymer interface. Furthermore, our findings shed light on rich and complex physics and materials design problems in PNCs, where the topological polymer structure on the nanofiller surface directly controls the macroscopic mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanically robust and reprocessable imine exchange networks from modular polyester pre-polymers

Covalent adaptable networks (CANs) containing reversible cross-links impart recyclability to thermoset materials without sacrificing their desirable properties (e.g. high tensile strength and solvent resistance). In addition to thermal recycling, the sustainability of these materials may be further improved by incorporating bio-sourced monomers or by enabling alternate end-of-life fates, such as biodegradation or recovery of starting materials. The alternating ring-opening copolymerisation of epoxides and cyclic anhydrides permits the modular synthesis of polyester pre-polymers that can then be cross-linked to form dynamic imine-linked networks. In this work, we report the synthesis and characterisation of five imine exchange polyester CANs with varied cross-linking densities and pre-polymer architectures. While the materials exhibit characteristic thermoset properties at service temperatures, differences in pre-polymer architecture produce distinct dynamic mechanical effects at elevated temperatures. The networks may be thermally reprocessed with full recovery of their tensile strengths and cross-linking densities, dissociated to pre-polymer, or hydrolytically degraded.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Energy Transfer Mechanisms in Large Low-Bandgap Polymers from Time-Resolved Experiments and Nonadiabatic Molecular Dynamics Calculations

Conjugated polymers offer unprecedented chemical tunability for modulating energy transfer in a multitude of infrared light applications. In this work, we use a combination of time-resolved spectroscopic experiments and nonadiabatic molecular dynamics calculations to probe the photochemistry and nonradiative transitions in a recently synthesized narrow bandgap donor–acceptor conjugated polymer based on alternating cyclopentadithiophene and electronegative benzothiadiazole heterocycles. Using large-scale semi-empirical nonadiabatic molecular dynamics, which can treat a large 260-atom hexamer, we calculate an S 5 → S 1 lifetime of 34.75 fs, which is consistent with our time-resolved spectroscopic data. Our simulations suggest that vibronic motions of the central carbons in the cyclopentadithiophene functional groups are predominantly involved in the nonradiative transitions, and the excitation becomes more localized on a monomer fragment over time. The combined use of time-resolved experiments and nonadiabatic molecular dynamics calculations in this work provides mechanistic insight into chemical functionalities that can be tuned to enhance energy transfer in other prospective low-bandgap polymer materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗