Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxygen diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Pressure dependence of the oxygen reduction reaction at the platinum microelectrode/nafion interface - Electrode kinetics and mass transport

The investigation of oxygen reduction kinetics at the platinum/Nafion interface is of great importance in the advancement of proton-exchange-membrane (PEM) fuel-cell technology. This study focuses on the dependence of the oxygen reduction kinetics on oxygen pressure. Conventional Tafel analysis of the data shows that the reaction order with respect to oxygen is unity at both high and low current densities. Chronoamperometric measurements of the transport parameters for oxygen in Nafion show that oxygen dissolution follows Henry's isotherm. The diffusion coefficient of oxygen is invariant with pressure; however, the diffusion coefficient for oxygen is lower when air is used as the equilibrating gas as compared to when oxygen is used for equilibration. These results are of value in understanding the influence of O2 partial pressure on the performance of PEM fuel cells and also in elucidating the mechanism of oxygen reduction at the platinum/Nafion interface.

Parthasarathy, Arvind↗
DOE OSTI2021

Persistent and partially mobile oxygen vacancies in Li-rich layered oxides

Increasing the energy density of layered oxide battery electrodes is challenging as accessing high states of delithiation often triggers voltage degradation and oxygen release. Here we utilize transmission-based X-ray absorption spectromicroscopy and ptychography on mechanically cross-sectioned Li 1.18–x Ni 0.21 Mn 0.53 Co 0.08 O 2–δ electrodes to quantitatively profile the oxygen deficiency over cycling at the nanoscale. The oxygen deficiency penetrates into the bulk of individual primary particles (~200 nm) and is well-described by oxygen vacancy diffusion. Using an array of characterization techniques, we demonstrate that, surprisingly, bulk oxygen vacancies that persist within the native layered phase are indeed responsible for the observed spectroscopic changes. We additionally show that the arrangement of primary particles within secondary particles (~5 μm) causes considerable heterogeneity in the extent of oxygen release between primary particles. Finally, our work merges an ensemble of length-spanning characterization methods and informs promising approaches to mitigate the deleterious effects of oxygen release in lithium-ion battery electrodes.

25 ENERGY STORAGE↗
DOE OSTI2024

Oxygen vacancy migration and impact on high voltage DC polarization in 0.8BaTiO 3 –0.2BiZn 0.5 Ti 0.5 O 3

Electrical polarization and defect transport are examined in 0.8BaTiO 3 –0.2BiZn 0.5 Ti 0.5 O 3 , an attractive capacitor material for high power electronics. Oxygen vacancies are suggested to be the majority charge carrier at or below 250°C with a grain conduction hopping activation energy of 0.97 eV and 0.92 eV for thermally stimulated depolarization current (TSDC) and impedance spectroscopy measurements, respectively. At higher temperature, thermally generated electronic conduction with an activation energy of 1.6 eV is dominant. Significant oxygen vacancy concentration is indicated (up to ~1%) due to cation vacancy formation (i.e., acceptor defects) from observed Bi (and likely Zn) volatility. Oxygen vacancy diffusivity is estimated to be 10 -12.8 cm 2 /s at 250°C. Low diffusivity and high activation energies are indicative of significant defect interactions. Dipolar oxygen vacancy defects are also indicated, with an activation energy of 0.59 eV from TSDC measurements. In conclusion, the large oxygen vacancy content leads to a short lifetime during high voltage (30 kV/cm), high temperature (250°C) direct current (DC) electrical measurements.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1998

Long Term Degradation of Polyimide Composites

The durability of polymer matrix composites exposed to harsh environments is a major concern. Surface degradation and damage are observed in polyimide composites used in air at 125-300 C. It is believed that diffusion of oxygen into the material and oxidative chemical reactions are responsible. Previous work has characterized and modeled diffusion behavior, and thermogravimetric analyses (TGAS) have been carried out in nitrogen, air, and oxygen to provide quantitative information on thermal and oxidative reactions. However, the model developed using these data did not successfully extrapolate TGA data down to conditions seen in service. A test program that focuses on lower temperatures and makes use of isothermal tests was undertaken to achieve a better understanding of the degradation reactions under use conditions. A new, low-cost technique was developed to collect chemical degradation data for isothermal tests lasting over 200 hours in the temperature range 125-300 C. Results indicate complex behavior not captured by the previous model, including the presence of weight-adding reactions. Weight gain reactions dominated in the 125-225 C temperature range, while weight loss reactions dominated beyond 225 C. The data obtained from isothermal tests and earlier TGAs is used to develop an advanced model of the material behavior.

Patekar, Kaustubh A.↗
NASA NTRS2000

Long Term Degradation of Resin for High Temperature Composites

The durability of polymer matrix composites exposed to harsh environments is a major concern. Surface degradation and damage are observed in polyimide composites used in air at 125 to 300 C. It is believed that diffusion of oxygen into the material and oxidative chemical reactions in the matrix are responsible. Previous work has characterized and modeled diffusion behavior, and thermogravimetric analyses (TGAs) have been carried out in nitrogen, air, and oxygen to provide quantitative information on thermal and oxidative reactions. However, the model developed using these data was not able to capture behavior seen in isothermal tests, especially those of long duration. A test program that focuses on lower temperatures and makes use of isothermal tests was undertaken to achieve a better understanding of the degradation reactions under use conditions. A new low-cost technique was developed to collect chemical degradation data for isothermal tests lasting over 200 hr in the temperature range 125 to 300 C. Results indicate complex behavior not captured by the previous TGA tests, including the presence of weight-adding reactions. Weight gain reactions dominated in the 125 to 225 C temperature range, while weight loss reactions dominated beyond 225 C. The data obtained from isothermal tests was used to develop a new model of the material behavior. This model was able to fully capture the behavior seen in the tests up to 275 C. Correlation of the current model with both isothermal data at 300 C and high rate TGA test data is mediocre. At 300 C and above, the reaction mechanisms appear to change. Attempts (which failed) to measure non-oxidative degradation indicate that oxidative reactions dominate the degradation at low temperatures. Based on this work, long term isothermal testing in an oxidative atmosphere is recommended for studying the degradation behavior of this class of materials.

Patekar, Kaustubh A.↗
DOE OSTI2022

Evaluating the Effects of Nitrogen Doping and Oxygen Doping on SRF Cavity Performance

Superconducting radiofrequency (SRF) cavities are resonators with extremely low surface resistance that enable accelerating cavities to have extremely high quality factors (Q₀). High Q₀ decreases the capital required to keep the accelerators cold by reducing power loss. The performance of SRF cavities is largely governed by the surface composition of the first §I{100}{nm} of the cavity surface. Impurities such as oxygen and nitrogen have been observed to yield high Q₀, but their precise roles are still being studied. Here, we compare the performance of cavities doped with nitrogen and oxygen in terms of surface composition and heating behavior with field. A simulation of the diffusion of oxygen into the bulk of the cavity was built using COMSOL Multiphysics software. Simulated results were compared to the actual surface composition of the cavities as determined from secondary ion mass spectrometry analysis. Understanding how these impurities affects performance allows us to have further insight into the underlying mechanisms that enable these surface treatments to yield high Q₀.

43 PARTICLE ACCELERATORS↗
NASA NTRS1985

Studies of oxygen-related and carbon-related defects in high-efficiency solar cells

Oxygen and carbon related defects in silicon, particularly as related to high-efficiency silicon solar cells were studied. A summary of oxygen processes in silicon versus process temperature was shown along with experimental results. The anamolous diffusion of oxygen was explained by the dissociation of the center allowing O sub i to move through the lattices.

Corbett, J. W.↗
DOE OSTI2021

Defect-driven selective metal oxidation at atomic scale

Nanoscale materials modified by crystal defects exhibit significantly different behaviours upon chemical reactions such as oxidation, catalysis, lithiation and epitaxial growth. However, unveiling the exact defect-controlled reaction dynamics (e.g. oxidation) at atomic scale remains a challenge for applications. Here, using in situ high-resolution transmission electron microscopy and first-principles calculations, we reveal the dynamics of a general site-selective oxidation behaviour in nanotwinned silver and palladium driven by individual stacking-faults and twin boundaries. The coherent planar defects crossing the surface exhibit the highest oxygen binding energies, leading to preferential nucleation of oxides at these intersections. Planar-fault mediated diffusion of oxygen atoms is shown to catalyse subsequent layer-by-layer inward oxide growth via atomic steps migrating on the oxide-metal interface. These findings provide an atomistic visualization of the complex reaction dynamics controlled by planar defects in metallic nanostructures, which could enable the modification of physiochemical performances in nanomaterials through defect engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Boosting the performance of reversible solid oxide electrochemical cells with a novel hybrid oxygen electrode, Pr 1.39 Ba 0.14 Sr 0.53 Co 1.48 Fe 0.76 O 6- δ -Ba 0.66 Sr 0.34 CoO 3- δ

Solid oxide electrochemical cells (SOECs) stand out as a highly promising clean energy technology that offers several benefits, showing significant potential to play a pivotal role in the transition towards a sustainable and low-carbon energy future. SOECs can efficiently convert the chemical energy stored in fuels to electricity in fuel cell mode, and produce various chemicals from abundant feedstocks (e.g., CO 2 , H 2 O) and intermittent solar/wind-based renewable electricity. Despite extensive efforts that have been devoted to designing novel materials and optimizing SOEC manufacturing processes, aiming to achieve enhanced energy efficiency, the current SOECs still suffer from poor performance, which is mainly due to the sluggish oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) kinetics. To address this challenge, in this work, we have successfully designed an in situ formed hybrid oxygen electrode material (Pr 1.39 Ba 0.14 Sr 0.53 Co 1.48 Fe 0.76 O 6- δ -Ba 0.66 Sr 0.34 CoO 3- δ ), which significantly improves the surface oxygen exchange coefficient and bulk oxygen-ion diffusion coefficient, enhancing the OER and ORR electrocatalytic activities. Further, the SOECs equipped with this newly developed oxygen electrode achieved exceptional performance for power generation using both hydrogen and propane as the fuels. At 750 °C, a peak power density of 2.4 W cm -2 was obtained with H 2 as the fuel. Additionally, the SOECs attain unprecedented performance in steam electrolysis mode. A current density of 4.4 A cm -2 was achieved at 1.3 V and 750 °C, which represents the highest performance among all yttria-stabilized zirconia (YSZ) electrolyte-based SOECs. The SOECs also deliver remarkable stability during the accelerated stability testing, highlighting the great potential of Pr 1.39 Ba 0.14 Sr 0.53 Co 1.48 Fe 0.76 O 6- δ -Ba 0.66 Sr 0.34 CoO 3- δ as a high-performance oxygen electrode for next generation SOECs.

08 HYDROGEN↗
DOE OSTI2025

Enhancing water and oxygen transport through electrode engineering for AEM water electrolyzers

Anion-exchange membrane water electrolyzers (AEMWEs) can accelerate the deployment of more efficient and affordable hydrogen production solutions. Here, electrode structure is shown to affect water back-diffusion and oxygen transport, which, in return, governs overpotential behaviors in AEMWEs. Measurements indicate that electrode with copious catalytic sites produces water close to the AEM, creating a higher water gradient and driving water back-diffusion, which improves membrane hydration and mass transport. In situ measurement reveals a high pH gradient near the anode surface, which affects anode kinetics. Operando measurement shows reduced oxygen accumulation when decoupling oxygen production and transport on anode. Catalyst ink rheology and stability are tuned with additives to realize scalable fabrication of electrodes with enhanced transport features, allowing AEMWE to operate at 2 A cm−2 for over 1,000+ h at a 2.3 μV h−1 degradation rate. Analysis during and post-durability provides insights into degradation mechanisms. This work demonstrates an electrode design strategy for efficient and durable AEMWEs.

AEM↗
DOE OSTI2025

Ultrafast Oxygen Conduction in Sillén Oxychlorides

Oxygen ion conductors are crucial for enhancing the efficiency of various clean energy technologies, including fuel cells, solid oxide air batteries, electrolyzers, membranes, sensors, and more. In this study, a structure-similarity analysis of ≈62k oxygen-containing compounds identified the MBi 2 O 4 X (M = rare-earth element, X = halogen element) family as promising candidates for fast oxygen transport. Among these, LaBi 2 O 4 Cl is found as an ultrafast oxygen conductor with an ultralow migration barrier of 0.1 eV based on ab initio studies. Its 2D layered structure, featuring a “triple fluorite” layer, supports diffusion of both oxygen vacancies and interstitials. In addition to vacancy diffusion with a 0.1 eV barrier, ab initio studies show interstitial diffusion exhibits a modest barrier of 0.6–0.8 eV. Frenkel pairs are found to be the dominant defects in intrinsic LaBi 2 O 4 Cl, facilitating significant vacancy-mediated oxygen diffusion at elevated temperatures. With 2.8% oxygen vacancies, LaBi 2 O 4 Cl is predicted to achieve a conductivity of 0.3 S/cm at 25 °C in a single crystal. Experimental synthesis and characterization of polycrystalline LaBi 2 O 4 Cl and Sr-doped LaBi 2 O 4 Cl revealed conductivity exceeding that of YSZ and LSGM below 400 °C, with lower activation energies, achieving a total conductivity of 0.1−0.2 mS/cm at 300 °C. Here, while these results confirm its potential of fast oxygen transport, we suggest further experimental optimization of LaBi 2 O 4 Cl, including aliovalent doping and microstructure refinement, could significantly enhance its performance, facilitating fast oxygen conduction approaching room temperature.

Defects↗
DOE OSTI2023

High-speed mapping of surface charge dynamics using sparse scanning Kelvin probe force microscopy

Unraveling local dynamic charge processes is vital for progress in diverse fields, from microelectronics to energy storage. This relies on the ability to map charge carrier motion across multiple length- and timescales and understanding how these processes interact with the inherent material heterogeneities. Towards addressing this challenge, we introduce high-speed sparse scanning Kelvin probe force microscopy, which combines sparse scanning and image reconstruction. This approach is shown to enable sub-second imaging (>3 frames per second) of nanoscale charge dynamics, representing several orders of magnitude improvement over traditional Kelvin probe force microscopy imaging rates. Bridging this improved spatiotemporal resolution with macroscale device measurements, we successfully visualize electrochemically mediated diffusion of mobile surface ions on a LaAlO 3 /SrTiO 3 planar device. Such processes are known to impact band-alignment and charge-transfer dynamics at these heterointerfaces. Furthermore, we monitor the diffusion of oxygen vacancies at the single grain level in polycrystalline TiO 2 . Through temperature-dependent measurements, we identify a charge diffusion activation energy of 0.18 eV, in good agreement with previously reported values and confirmed by DFT calculations. Together, these findings highlight the effectiveness and versatility of our method in understanding ionic charge carrier motion in microelectronics or nanoscale material systems.

25 ENERGY STORAGE↗
NASA NTRS1998

The Oxidation of AlN in Dry and Wet Oxygen

The oxidation kinetics of AlN containing 3.5 wt% Y2O3 were studied by thermogravimetric analysis in dry oxygen and 10% H2O/balance oxygen at temperatures between 1000 and 1200 C for times between 48 and 100 h. The oxidation kinetics for AlN in dry oxygen were parabolic and of approximately the same magnitude and temperature dependence as other alumina forming materials. In this case, diffusion of oxygen and/or aluminum through the alumina scale is the rate limiting mechanism. The oxidation kinetics for AlN in wet oxygen were nearly linear and much more rapid than rates observed in dry oxygen. Numerous micropores were observed in the alumina formed on AIN in wet oxygen. These pores provide a fast path for oxygen transport. The linear kinetics observed in this case suggest that the interface reaction rate of AlN with wet oxygen is the oxidation rate limiting step.

Opila, Elizabeth↗
NASA NTRS1986

High-temperature oxidation of a rapidly solidified amorphous Ta-Ir alloy

The oxidation products formed at 500 and 700 C on an amorphous Ta-44.5 at. pct Ir alloy in an Ar-0.1 percent O2 gas mixture were characterized using SEM, XRD, EPMA, TEM, STEM, AES, and XPS. Initially, a thin (3-4 nm) layer of Ta2O5 formed at the surface of the alloy. Continued growth of the Ta2O5, which occurred very rapidly, involved diffusion of oxygen anions from the Ta2O5/gas interface to the alloy/Ta2O5 interface, where tantalum was selectively oxidized. Because the oxide grew more quickly than iridium could diffuse back into the alloy, the iridium coalesced into platelets of crystalline iridium-rich alloy that were oriented approximately parallel to the oxide/alloy interface, and which became embedded in a matrix of Ta2O5. The unoxidized core remained in the glassy state. The oxidation process and/or the dissolution of oxygen into the unoxidized alloy caused the alloy to become embrittled.

Cotell, Catherine M.↗
DOE OSTI2023

The Dynamics of Oxygen Ion Exchange in Epitaxial Strontium Cobaltite Bilayers

Abstract The exchange of ions across interfaces is key to the field of iontronics, where the properties of the device can be altered by the local ion concentration. This study investigates a complex oxide system where structural and electronic phase transitions can be driven by changes in the concentration of oxygen ions. In situ coherent X‐ray studies are conducted on epitaxial bilayers of insulating SrCoO 2.5 and metallic SrCoO 3 − δ . The diffusion of oxygen ions across the bilayer is studied with X‐ray photon correlation spectroscopy to capture the dynamical behavior of the interface in reducing and oxidizing environments. The behavior is strongly asymmetric, with much slower dynamics appearing in reducing versus oxidizing environments. According to the correlation functions determined from different points in reciprocal space, this study finds that the dynamics near the center of the SrCoO 2.5 crystal are generally similar to those near the heterointerfaces. The results suggest that the interface is stable and reversible, making SrCoO x a model system for the study of iontronic behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Oxygen vacancy dynamics in monoclinic metallic VO 2 domain structures

It was demonstrated recently that the nano-optical and nanoelectronic properties of VO 2 can be spatially programmed through the local injection of oxygen vacancies by atomic force microscope writing. In this work, we study the dynamic evolution of the patterned domain structures as a function of the oxygen vacancy concentration and the time. A threshold doping level is identified that is critical for both the metal–insulator transition and the defect stabilization. The diffusion of oxygen vacancies in the monoclinic phase is also characterized, which is directly responsible for the short lifetimes of sub-100 nm domain structures. This information is imperative for the development of oxide nanoelectronics through defect manipulations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Mesoscopic analyses of the impact of morphology and operating conditions on the transport resistances in a proton-exchange-membrane fuel-cell catalyst layer

Exploring the origins of local transport resistance and characterizing the oxygen transport resistances in the catalyst layer (RCL) are critical for cost reduction. In this paper, a comprehensive mesoscopic model for simulating coupled transport processes of oxygen and water vapor for different structural parameters under different operating conditions in reconstructed microstructures is proposed. The local transport resistance is calculated after achieving the limiting current density and the effective diffusivity of oxygen. The results demonstrate that RCL increases greatly with decreasing platinum loading (LPt) and the transport resistances in other components of the cell dominate for high-loadings. Both the reduced oxygen permeation coefficient in the ionomer thin-film and the adsorption resistance account for the origins of local transport resistance. The local transport resistance increases with the bare carbon ratio for a constant LPt and Pt/C ratio due to the decreased effective ionomer surface, and increases with the I/C ratio due to the increased ionomer thickness and decreased Knudsen diffusivity. Due to the presence of liquid water, a slight decrease followed by an increase of the local transport resistance versus relative humidity is obtained. The contribution of ionomer thin-films to RCL is more sensitive to liquid saturation compared with that of pores. This journal is

Mu, YT↗