Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstrip”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

The design and fabrication of microstrip omnidirectional array antennas for aerospace applications

A microstrip antenna design concept was developed that will provide quasi-omnidirectional radiation pattern characteristics about cylindrical and conical aerospace structures. L-band and S-band antenna arrays were designed, fabricated, and, in some cases, flight tested for rocket, satellite, and aircraft drone applications. Each type of array design is discussed along with a thermal cover design that was required for the sounding rocket applications.

Campbell, T. G.↗
NASA NTRS1980

Multiband microstrip antenna

Compact antenna transmits and receives elliptically and circularly polarized radiation. Antenna consists of layers of elliptical disks separated by dielectric substrates. Each disk operates at frequency determined by its size and dielectric constant of substrate. Individual frequency bands can be made to overlap, to yield single broadband antenna. Standard microstrip techniques are used to build it.

Yu, I.↗
NASA NTRS1980

A bounds on the resonant frequency of rectangular microstrip antennas

The calculation of currents induced by a transverse electric plane wave normally incident upon an infinite strip embedded in a grounded dielectric slab is used to infer a lower bound on the resonant frequency (or resonant-E-plane dimension) for rectangular microstrip antennas. An upper bound is provided by the frequency for which the E-plane dimension is a half-wavelength.

Bailey, M. C.↗
NASA NTRS1981

The design of a microstrip antenna array for a UHF space telemetry link

An array of microstrip antenna panels was designed for use on a small instrumented satellite as part of a 400-MHz telemetry link between that satellite and NASA's shuttle spacecraft. A roughly omnidirectional phi-plane pattern was desired. The 1.4-wavelength diameter of the satellite and the various ports and structures on its surface presented strong constraints on the antenna array design. Eight antennas, each one a quarter-wavelength panel with one radiating and one shorted edge, were chosen. A phi-plane pattern ripple of 4.4 dB and a gain of at least 0.1 dB relative to a half-wavelength dipole were realized. The design technique used for the individual antenna panels included the study of feed-point location for impedance matching and the effect of losses in the dielectric. A superposition method was used to synthesize the radiation patterns for different numbers and different excitations of antennas on the satellite.

Post, R. E.↗
NASA NTRS1982

Input impedance and mutual coupling of rectangular microstrip antennas

A moment method solution to the problem of input impedance and mutual coupling of rectangular microstrip antenna elements is presented. The formulation uses the grounded dielectric slab Green's function to account rigorously for the presence of the substrate and surface waves. Both entire basis (EB) and piecewise sinusoidal (PWS) expansion modes are used, and their relative advantages are noted. Calculations of input impedance and mutual coupling are compared with measured data and other calculations.

Pozar, D. M.↗
NASA NTRS1983

The finite ground plane effect on the microstrip antenna radiation patterns

The uniform geometrical theory of diffraction (GTD) is employed for calculating the edge diffracted fields from the finite ground plane of a microstrip antenna. The source field from the radiating patch is calculated by two different methods: the slot theory and the modal expansion theory. Many numerical and measured results are presented to demonstrate the accuracy of the calculations and the finite ground plane edge effect.

Huang, J.↗
NASA NTRS1984

The study of microstrip antenna arrays and related problems

The work on rectangular microstrip antennas for dual frequency operation is reported on. The principle of this approach is based on the excitation of a patch for two or more different modes which correspond to different frequencies. However, for a given geometry, the modal frequencies have a fixed relationship; therefore, the usefulness of such a design is greatly limited. In this study three different methods have been contrived to control the frequency ratio over a wide range. First, as found prevously, if shorting pins are inserted at certain locations in the patch, the low frequency can be raised substantially. Second, if slots are cut in the patch, the high frequency can be lowered considerably. By using both techniques, the two frequency ratio can be varied approximately from 3 to 1.3. After that, the addition of more pins or slots becomes ineffective.

Lo, R. Q.↗
NASA NTRS1984

Microstrip antennas for dual-frequency operation

Single element microstrip antenna for dual-frequency operation have been investigated. By placing shorting pins at appropriate locations in the patch, the ratio of two-band frequencies can be varied from 3 to 1.8. In many applications a smaller ratio is desired, and this can be achieved by introducing slots in the patch. In so doing, the ratio can be reduced to less than 1.3. For this type of antenna, a hybrid multiport theory is developed and theoretical results are found to be in excellent agreement with the measured.

Wang, B. F.↗
NASA NTRS1984

Circularly polarized conical patterns from circular microstrip antennas

A method is presented for generating circularly polarized conical patterns from circular microstrip antennas. These antennas are excited at higher order modes and require different feed arrangements for different mode excitations. It is determined that the peak direction of the conical pattern can be varied over a wide angular range. Modal expansion technique is employed to calculate the radiation patterns of these antennas.

Huang, J.↗
NASA NTRS1984

Analysis of an infinite array of rectangular microstrip patches with idealized probe feeds

A solution is presented to the problem of an infinite array of microstrip patches fed by idealized current probes. The input reflection coefficient is calculated versus scan angle in an arbitrary scan plane, and the effects of substrate parameters and grid spacing are considered. It is pointed out that even when a Galerkin method is used the impedance matrix is not symmetric due to phasing through a unit cell, as required for scanning. The mechanism by which scan blindness can occur is discussed. Measurement results are presented for the reflection coefficient magnitude variation with angle for E-plane, H-plane, and D-plane scans, for various substrate parameters. Measured results from waveguide simulators are also presented, and the scan blindness phenomenon is observed and discussed in terms of forced surface waves and a modified grating lobe diagram.

Pozar, D. M.↗
NASA NTRS1985

Dual-band reactively loaded microstrip antenna

A previously derived theory is applied to a microstrip antenna with a reactive load to produce a dual-band radiator. A model consisting of a rectangular patch radiator loaded with a variable length short-circuited coaxial stub was investigated experimentally. Comparisons of theoretical predictions and experimental data are made for the impedance and resonant frequencies as a function of the position of the load, the length of the stub, and the characteristic impedance of the stub.

Richards, W. F.↗
NASA NTRS1985

Analysis of elliptical and circular microstrip antennas using moment method

A method of calculating the input impedance of either a circular or a slightly elliptical microstrip antenna excited by a coaxial probe is presented. Using the reaction integral equation and the exact dyadic Green's function, the finite substrate thickness is taken into account in the formulation. Good agreement with experimental results for an elliptical patch is obtained and a design procedure for a circularly polarized antenna is presented.

Bailey, M. C.↗
NASA NTRS1986

Microstrip Antenna Generates Circularly Polarized Beam

Circular microstrip antenna excited with higher order transverse magnetic (TM) modes generates circularly polarized, conical radiation patterns. Found both theoretically and experimentally that peak direction of radiation pattern is varied within wide angular range by combination of mode selection and loading substrate with materials of different dielectric constants.

Huang, J.↗
NASA NTRS1985

Circularly polarized microstrip antennas

A simple microstrip antenna can be made to radiate EM waves of any polarization, in particular, the circular polarization (CP) without any phasing network and power divider. A simple and accurate theory for this family of antennas was developed. However, the CP bandwidth, (CPBW) the bandwidth in which the axial ratio (AR) is less than a certain specified value, is very small. Most of the experimental designs were made for a feed placed along the diagonal of the patch. It is shown that there are practically infinitely many possible designs with different feed location. The speculation that other designs might give a wider bandwidth is clarified and an effective method for broadening the bandwidth is shown.

Lo, Y. T.↗
NASA NTRS1986

A new model for broadband waveguide to microstrip transition design

A new model is presented which permits the prediction of the resonant frequencies created by antipodal finline waveguide to microstrip transitions. The transition is modeled as a tapered transmission line in series with an infinite set of coupled resonant circuits. The resonant circuits are modeled as simple microwave resonant cavities of which the resonant frequencies are easily determined. The model is developed and the resonant frequencies determined for several different transitions. Experimental results are given to confirm the models.

Ponchak, George E.↗
NASA NTRS1987

Microstrip antenna array with parasitic elements

Discussed is the design of a large microstrip antenna array in terms of subarrays consisting of one fed patch and several parasitic patches. The potential advantages of this design are discussed. Theoretical radiation patterns of a subarray in the configuration of a cross are presented.

Lee, Kai F.↗
NASA NTRS1987

An experimental investigation of parasitic microstrip arrays

The characteristics of a parasitic microstrip antenna array with a center-fed patch are experimentally investigated. The parasitic array is composed of identical parasitic patches which are symmetrically arranged and electromagnetically coupled to a center-fed patch. The shape and dimensions of the parasitic patches and their positions relative to the center-fed patch are parameters in the study. To show mutual coupling effects between radiating and nonradiating edges of adjacent patches, the impedance and radiation characteristics of a three-element parasitic array excited with (0.1) mode are examined, and compared to that of a single patch. Experimental data indicate that the presence of parasitic patches has significant effects upon the gain, resonant frequency, and impedance bandwidth of the array.

Lee, Richard Q.↗