Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “memory effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A phase-field model for non-isothermal phase transformation and plasticity in polycrystalline yttria-stabilized tetragonal zirconia

Here we propose an elastoplastic phase-field (PF) model to investigate the mechanics of tetragonal-to-monoclinic phase transformation (TMPT) and elastoplastic deformation of polycrystalline yttria-stabilized tetragonal zirconia (YSTZ). A Landau polynomial with non-vanishing chemical energy at the equilibrium temperature is introduced to account for the actual formation energies of the phases. The effects of different grain orientations, latent heat, and temperature on TMPT and deformation mechanisms are considered. The suppressive transformation effects of the grain boundaries (GBs) is modeled using an inhomogeneous kinetic coefficient in the bulk and GBs. The simulation results for single crystals demonstrate the capability of the model to reproduce the orientation-dependent compressive deformation of YSTZ similar to atomistic simulations and micropillar experiments. The single crystal with [100] crystallographic orientation along the loading direction (SC[100]) displays both TMPT and plasticity, SC[101] experiences only phase transformation, while SC[001] undergoes only plastic yielding. The TMPT induced by compressive loading exhibits shape memory effect (SME) below the equilibrium transformation temperature and pseudoelasticity above it, while the critical transformation stress increases with increasing loading temperature. The irrecoverable plastic strain is found to trap a part of the monoclinic phase, which prevents a complete reverse transformation. The polycrystalline cases also display SME and PE at low and high temperatures, respectively. Due to the orientation differences between grains and the stress concentrations at geometric nonlinearities, plastic deformation occurs in polycrystalline YSTZ for an applied load less than the yield stress. The results suggest a possible limitation of plasticity and an improvement of the shape recovery of YSTZ if one can control the orientation of the grains and/or increase the density of stacking faults at the GBs during material processing.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Reversible migration of silver on memorized pathways in Ag-Ge{sub 40}S{sub 60} films

Reversible and reproducible formation and dissolution of silver conductive filaments are studied in Ag-photodoped thin-film Ge{sub 40}S{sub 60} subjected to electric fields. A tip-planar geometry is employed, where a conductive-atomic-force microscopy tip is the tip electrode and a silver patch is the planar electrode. We highlight an inherent “memory” effect in the amorphous chalcogenide solid-state electrolyte, in which particular silver-ion migration pathways are preserved “memorized” during writing and erasing cycles. The “memorized” pathways reflect structural changes in the photodoped chalcogenide film. Structural changes due to silver photodoping, and electrically-induced structural changes arising from silver migration, are elucidated using Raman spectroscopy. Conductive filament formation, dissolution, and electron (reduction) efficiency in a lateral device geometry are related to operation of the nano-ionic Programmable Metallization Cell memory and to newly emerging chalcogenide-based lateral geometry MEMS technologies. The methods in this work can also be used for qualitative multi-parameter sampling of metal/amorphous-chalcogenide combinations, characterizing the growth/dissolution rates, retention and endurance of fractal conductive filaments, with the aim of optimizing devices.

36 MATERIALS SCIENCE↗
NASA NTRS2013

The Effect of Pre-Stressing on the Static Indentation Load Capacity of the Superelastic 60NiTi

Superelastic nickel-titanium alloys, such as 60NiTi (60Ni-40Ti by wt.%), are under development for use in mechanical components like rolling element bearings and gears. Compared to traditional bearing steels, these intermetallic alloys, when properly heat-treated, are hard but exhibit much lower elastic modulus (approx.100 GPa) and a much broader elastic deformation range (approx.3 percent or more). These material characteristics lead to high indentation static load capacity, which is important for certain applications especially space mechanisms. To ensure the maximum degree of elastic behavior, superelastic materials must be pre-stressed, a process referred to as "training" in shape memory effect (SME) terminology, at loads and stresses beyond expected use conditions. In this paper, static indentation load capacity tests are employed to assess the effects of pre-stressing on elastic response behavior of 60NiTi. The static load capacity is measured by pressing 12.7 mm diameter ceramic Si3N4 balls into highly polished, hardened 60NiTi flat plates that have previously been exposed to varying levels of pre-stress (up to 2.7 GPa) to determine the load that results in shallow but measurable (0.6 m, 25 in. deep) permanent dents. Hertz stress calculations are used to estimate contact stress. Without exposure to pre-stress, the 60NiTi surface can withstand an approximately 3400 kN load before significant denting (>0.4 m deep) occurs. When pre-stressed to 2.7 GPa, a static load of 4900 kN is required to achieve a comparable dent, a 30 percent increase. These results suggest that stressing contact surfaces prior to use enhances the static indentation load capacity of the superelastic 60NiTi. This approach may be adaptable to the engineering and manufacture of highly resilient mechanical components such as rolling element bearings.

DellaCorte, Christopher↗
NASA NTRS1989

Springback in root gravitropism

Conditions under which a gravistimulus of Merit corn roots (Zea mays L.) is withdrawn result in a subsequent loss of gravitropic curvature, an effect which we refer to as springback.' This loss of curvature begins within 1 to 10 minutes after removal of the gravistimulus. It occurs regardless of the presence or absence of the root cap. It is insensitive to inhibitors of auxin transport (2,3,5-triiodobenzoic acid, naphthylphthalamic [correction of naphthylphthalmaic] acid) or to added auxin (2,4-dichlorophenoxyacetic acid). Springback is prevented if a clinostat treatment is interjected to neutralize gravistimulation during germination, which suggests that the change in curvature is a response to a memory' effect carried over from a prior gravistimulation.

NASA Discipline Plant Biology↗
DOE OSTI2019

Programmable bias field observed in graded ferromagnetic semiconductor films with broken symmetry

We report on the observation of a field-induced magnetic bias effect in a Ga 0.94 Mn 0.06 As 1-y P y thin film with digitally graded phosphorus content. Although phosphorus concentration in the sample is changed in steps from y approximate to 0.03 to y approximate to 0.28, the magnetometry and magnetotransport data display a coherent magnetic response typical for single-layer in-plane magnetized films with cubic and weak [110] uniaxial anisotropy. Unexpectedly, low-temperature planar Hall resistance loops exhibit remarkable asymmetry tunable by application of strong in-plane initial magnetic field H Ini . We discuss this unusual memory effect, resembling the magnetization asymmetry in the exchange biased magnetic bilayers, in terms of a unidirectional bias field H b induced by H Ini . We show that such bias field defines the delayed or accelerated nucleation of domains with chiral domain walls performing the magnetization reversal.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Causal Inference Model Based on Random Forests to Identify the Effect of Soil Moisture on Precipitation

Soil moisture influences precipitation mainly through its impact on land–atmosphere interactions. Understanding and correctly modeling soil moisture–precipitation (SM–P) coupling is crucial for improving weather forecasting and subseasonal to seasonal climate predictions, especially when predicting the persistence and magnitude of drought. However, the sign and spatial structure of SM–P feedback are still being debated in the climate research community, mainly due to the difficulty in establishing causal relationships and the high degree of nonlinearity in land–atmosphere processes. To this end, we developed a causal inference model based on the Granger causality analysis and a nonlinear machine learning model. This model includes three steps: nonlinear anomaly decomposition, nonlinear Granger causality analysis, and evaluation of the quality of SM–P feedback, which eliminates the nonlinear response of interannual and seasonal variability and the memory effects of climatic factors and isolates the causal relationship of local SM–P feedback. We applied this model by using National Climate Assessment–Land Data Assimilation System (NCA-LDAS) datasets over the United States. Here, the results highlight the importance of nonlinear atmosphere responses in land–atmosphere interactions. In addition, the strong feedback over the southwestern United States and the Great Plains both highlight the impacts of topographic factors rather than only the sensitivity of evapotranspiration to soil moisture. Furthermore, the SM–P index defined by our framework is used to benchmark Earth system models (ESMs), which provides a new metric for efficiently identifying potential model biases in modeling local land–atmosphere interactions and may help the development of ESMs in improving simulations of water cycle variability and extremes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2016

Final Report, University of California Merced: Uranium and strontium fate in waste-weathered sediments: Scaling of molecular processes to predict reactive transport

Objectives of the Project: 1. Determine the process coupling that occurs between mineral transformation and contaminant (U and Sr) speciation in acid-uranium waste weathered Hanford sediments. 2. Establish linkages between molecular-scale contaminant speciation and meso-scale contaminant lability, release and reactive transport. 3. Make conjunctive use of molecular- to bench-scale data to constrain the development of a mechanistic, reactive transport model that includes coupling of contaminant sorption-desorption and mineral transformation reactions. Hypotheses Tested: Uranium and strontium speciation in legacy sediments from the U-8 and U-12 Crib sites can be reproduced in bench-scale weathering experiments conducted on unimpacted Hanford sediments from the same formations; Reactive transport modeling of future uranium and strontium releases from the vadose zone of acid-waste weathered sediments can be effectively constrained by combining molecular-scale information on contaminant bonding environment with grain-scale information on contaminant phase partitioning, and meso-scale kinetic data on contaminant release from the waste-weathered porous media; Although field contamination and laboratory experiments differ in their diagenetic time scales (decades for field vs. months to years for lab), sediment dissolution, neophase nucleation, and crystal growth reactions that occur during the initial disequilibrium induced by waste-sediment interaction leave a strong imprint that persists over subsequent longer-term equilibration time scales and, therefore, give rise to long-term memory effects. Enabling Capabilities Developed: Our team developed an iterative measure-model approach that is broadly applicable to elucidate the mechanistic underpinnings of reactive contaminant transport in geomedia subject to active weathering.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2016

Uranium and strontium fate in waste-weathered sediments: Scaling of molecular processes to predict reactive transport

Objectives of the project: 1. Determine the process coupling that occurs between mineral transformation and contaminant (U and Sr) speciation in acid-uranium waste weathered Hanford sediments. 2. Establish linkages between molecular-scale contaminant speciation and meso-scale contaminant lability, release and reactive transport. 3. Make conjunctive use of molecular- to bench-scale data to constrain the development of a mechanistic, reactive transport model that includes coupling of contaminant sorption-desorption and mineral transformation reactions. Hypotheses tested: - Uranium and strontium speciation in legacy sediments from the U-8 and U-12 Crib sites can be reproduced in bench-scale weathering experiments conducted on unimpacted Hanford sediments from the same formations. - Reactive transport modeling of future uranium and strontium releases from the vadose zone of acid-waste weathered sediments can be effectively constrained by combining molecular-scale information on contaminant bonding environment with grain-scale information on contaminant phase partitioning, and meso-scale kinetic data on contaminant release from the waste-weathered porous media. - Although field contamination and laboratory experiments differ in their diagenetic time scales (decades for field vs. months to years for lab), sediment dissolution, neophase nucleation, and crystal growth reactions that occur during the initial disequilibrium induced by waste-sediment interaction leave a strong imprint that persists over subsequent longer-term equilibration time scales and, therefore, give rise to long-term memory effects. Enabling capabilities developed: Our team developed an iterative measure-model approach that is broadly applicable to elucidate the mechanistic underpinnings of reactive contaminant transport in geomedia subject to active weathering. Experimental design: Hypotheses were tested by comparing (with a similar set of techniques) the geochemical transformations and transport behaviors that occured in bench-scale studies of waste-sediment interaction with parallel model systems studies of homogeneous nucleation and neo-phase dissolution. Initial plans were to compare results with core sample extractions from the acid uranium waste impacted U-8 and U-12 Cribs at Hanford (see original proposal and letter of collaboration from J. Zachara). However, this part of the project was impossible because funding for core extractions were eliminated from the DoE budget. Three distinct crib waste aqueous simulants (whose composition is based on the most up-to-date information from field site investigations) were reacted with Hanford sediments in batch and column systems. Coupling of contaminant uptake to mineral weathering was monitored using a suite of methods both during waste-sediment interaction, and after, when waste-weathered sediments were subjected to infusion with circumneutral background pore water solutions. Our research was designed to adapt as needed to maintain a strong dialogue between laboratory and modeling investigations so that model development was increasingly constrained by emergent data and understanding. Potential impact of the project to DOE: Better prediction of contaminant uranium transport was achieved by employing multi-faceted lines of inquiry to build a strong bridge between molecular- and field-scale information. By focusing multiple lines and scales of observation on a common experimental design, our collaborative team revealed non-linear and emergent behavior in contaminated weathering systems. A goal of the current project was to expand our modeling capabilities, originally focused on hyperalkaline legacy waste streams, to include acidic weathering reactions that, as described above, were expected to result in profoundly different products. We were able to achieve this goal, and showed that these products nonetheless undergo analogous silicate and non-silicate transformation, ripening and aging processes. Our prediction that these weathering reactions would vary with waste stimulant chemistry resulted in data that was incorporated directly into a reactive transport model structure.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Thermally Activated Circularly Polarized Photoluminescence in a 2D Hybrid Perovskite with Giant Spin Splitting

Circularly polarized light generation and detection are critical for future spin-based technologies that inter-convert circularly polarized photons and electron spins. However, detailed mechanisms in such spin-photon interfaces are often either poorly understood or operate at cryogenic temperatures since typically small energies separating spin-split electronic bands facilitate thermally driven spin depolarization. Recently, several 2D hybrid perovskites with polar achiral cations were theoretically demonstrated to exhibit conduction and valence band spin-splitting energies greatly exceeding room-temperature thermal energy, suggesting their utility as spin-photon interfaces with practical operating temperatures. Here, a strong "spin memory" effect is reported in such a polar achiral layered perovskite that enables large room-temperature circularly polarized emission anisotropy following excitation with circularly polarized light. The polarization anisotropy depends strongly on temperature (thermally activated), excitation energy, and crystal orientation with respect to the excitation source. Temperature-dependent photoconductance measurements reveal similar thermally activated carrier generation. These observations suggest a mechanism whereby giant in-plane splitting of single-particle levels protects spin-polarization of photogenerated electrons and holes before recombination. Although polarized light emission is explored in greater detail in chiral perovskites, these results reveal that even without chirality, large spin memory in polar achiral perovskites can enable spin-photon interfaces that operate at elevated temperatures.

14 SOLAR ENERGY↗
DOE OSTI2015

Spectroscopic properties and radiation damage investigation of a diamond based Schottky diode for ion-beam therapy microdosimetry

In this work, a detailed analysis of the properties of a novel microdosimeter based on a synthetic single crystal diamond is reported. Focused ion microbeams were used to investigate the device spectropscopic properties as well as the induced radiation damage effects. A diamond based Schottky diode was fabricated by chemical vapor deposition with a very thin detecting region, about 400 nm thick (approximately 1.4 μm water equivalent thickness), corresponding to the typical size in microdosimetric measurements. A 200 × 200 μm{sup 2} square metallic contact was patterned on the diamond surface by standard photolithography to define the sensitive area. Experimental measurements were carried out at the Ruder Boškovic′ Institute microbeam facility using 4 MeV carbon and 5 MeV silicon ions. Ion beam induced charge maps were employed to characterize the microdosimeter response in terms of its charge collection properties. A stable response with no evidence of polarization or memory effects was observed up to the maximum investigated ion beam flux of about 1.7 × 10{sup 9} ions·cm{sup −2}·s{sup −1}. A homogeneity of the response about 6% was found over the sensitive region with a well-defined confinement of the response within the active area. Tests of the radiation damage effect were performed by selectively irradiating small areas of the device with different ion fluences, up to about 10{sup 12} ions/cm{sup 2}. An exponential decrease of the charge collection efficiency was observed with a characteristic decay constant of about 4.8 MGy and 1 MGy for C and Si ions, respectively. The experimental data were analyzed by means of GEANT4 Monte Carlo simulations. A direct correlation between the diamond damaging effect and the Non Ionizing Energy Loss (NIEL) fraction was found. In particular, an exponential decay of the charge collection efficiency with an exponential decay as a function of NIEL is observed, with a characteristic constant of about 9.3 kGy-NIEL for both carbon and silicon ions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRSDate not supplied

Design and Analysis of Shape Memory Spring Tires for Martian and Lunar Rover Vehicles

Shape memory alloys (SMAs) have played an important role in various innovative engineering and medical applications, such as aerospace actuators, vibration damping devices, and coronary stents. In applications, shape memory alloys are commonly utilized in two fundamentally different ways: (i) making use of the superelasticity/ pseudoelasticity (SE/PE) phenomena, as in applications in biomedical engineering, and (ii) taking advantages of the shape memory effect (SME), as is used for actuators. Their ability to act in such vastly different capacities is mainly due to their unique capability to recover large amounts of deformation produced by either applied stresses or temperature changes. One recent emerging application in use of SMAs has been in the area of non-pneumatic tire designs for Martian or Lunar roving vehicles. These vehicles require tires that are capable of traversing rugged terrain while withstanding extreme temperatures and atmospheric conditions. Inspired by the flexible wire mesh tires used on three Lunar Roving Vehicle (LRV) missions to the Moon on Apollo 15, 16, and 17, a new compliant tire technology was developed by the NASA Glenn Research Center (GRC) and Goodyear Tire & Rubber, known as the Spring Tire. The Spring Tire consists of several hundred coiled springs woven into a flexible mesh and formed into the shape of a tire. Like the LRV wire mesh tires, the original Spring Tires were made from spring steel and were prone to permanent deformation when undergoing high localized loads. Later, a new iteration of this technology was invented, known as the ‘Superelastic Tire’. This new technology incorporated the use of superelastic SMA springs, which could effectively undergo approximately 30 times more reversible deformation than the steel spring. It also provided even greater durability and allowed for more flexibility in design, such as the use of other structural forms to reduce mass or increase load carrying capacity. Because of the unique nature of both the SMA material and the complex interactions between the springs, designing Spring Tires for a specific application requires extensive effort. Historically, design decisions have relied on full-scale empirical testing; however, this is very expensive and time consuming, especially when multiple iterations are needed. Therefore, developing a large-scale, robust, and predictive numerical model entailing complex spring interactions and the shape memory material behavior within a tire construct is the first essential step towards a successful design program. The current work focuses on implementation of the user-defined Shape Memory Alloy (SMA) model, otherwise known as SMA-GVIPs, in the Finite Element analysis (FEA) program ABAQUS for large-scale simulations of the GRC-developed Spring Tires made of SMA. The novelty of this work lies in the thorough, detail-oriented, and computationally efficient finite element analysis of full-scale SMA tires. A well-thought material characterization plan followed by model validation and a systemic sensitivity study on SMA tires has never been reported in the previous literature. The main objective of this study is to help the team improve and optimize the structural design of the SMA tires through in-depth numerical analysis and sensitivity studies. Various design variables (wire diameter, coil diameter, pitch, bead angle, and number of springs) were varied to study their influence on the global load-displacement response of the tire construct. A detailed investigation of the three-dimensional stress states was also carried out to enhance our understanding of the local changes as the tire goes through global deformation. It was concluded that a robust numerical model with a good predictive capability, together with a thoughtfully crafted sensitivity study can result in improved design iterations required to reach a desired tire performance while, significantly reducing manufacturing, labor and testing expenses. A summary of the Finite Element (FE) model construction will be presented together with a description of the user-defined SMA model, characterization process, experimental results, model validation, and numerical sensitivity study results.

shape memory alloys↗
DOE OSTI2025

Neuromorphic heat transport effects in a molecular junction

Understanding energy transport at the nanoscale is an open and fundamental challenge in the molecular sciences with direct implications for the design of new electronics, computing devices, and materials. While nanoscale energy transport under steady-state conditions has been studied extensively, there is much less known about energy transport under time-dependent driving forces, particularly in the far-from-equilibrium regime. In this work, we use nonequilibrium molecular dynamics simulations and stochastic thermodynamics to investigate energy transport in a well-studied nanoscale system—a molecular junction—subjected to a time-periodic temperature gradient. The primary observation is that molecular junctions can exhibit heat transport hysteresis, a phenomenon in which the heat flux through a system depends not only on the instantaneous value of a time-dependent temperature bias but also on the temporal history of that bias. The presented findings illustrate that molecular junctions can exhibit the specific memory effect—heat transport hysteresis—that is essential for the design of thermal neuromorphic computers. This work elucidates a potential pathway toward the realization of such devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Physical Modeling and Design of a Nonvolatile Optically Gated High‐Power Diamond Transistor

In this work, we present the theory and modeling framework of a diamond optically gated junction field‐effect transistor (DOGFET). The device utilizes nitrogen substitutional centers in type‐1b diamond to optically modulate a p‐ boron doped diamond channel. Using sub‐gap lasers with intensities as low as 100 W/cm 2 , electrons are optically excited from substitutional nitrogen sites to the conduction band of the diamond substrate, thus enabling the optical gate to exercise control on modulating the space‐charge region at the junction and therefore the channel conductivity. We show that the device can deliver a current of 7 μA/μm, or equivalently 1750 A/cm 2 , while switching at a frequency greater than 100 kHz, in a form factor of 5 μm 2 . The breakdown voltage is found to be greater than 1850 V, with a breakdown field strength of ~13 MV/cm. Moreover, the device supports nonvolatile operation with a “memory effect” enabling single transistor state retention. The presented simulation framework provides a physically grounded insight into the limits and opportunities of optoelectronic diamond systems.

Engineering - Electronic and electrical engineerin↗
NASA NTRS2016

Ab Initio Simulations of Phase Stability and Martensitic Transitions in NiTi

For NiTi based alloys, the shape memory effect is governed by a transition from a low-temperature martensite phase to a high-temperature austenite phase. Despite considerable experimental and computational work, basic questions regarding the stability of the phases and the martensitic phase transition remain unclear even for the simple case of binary, equiatomic NiTi. We perform ab initio molecular dynamics simulations to describe the temperature-dependent behavior of NiTi and resolve several of these outstanding issues. Structural correlation functions and finite temperature phonon spectra are evaluated to determine phase stability. We show that finite temperature, entropic effects stabilize the experimentally observed martensite (B19') and austenite (B2) phases while destabilizing the theoretically predicted (B33) phase. Free energy computations based on ab initio thermodynamic integration confirm these results and permit estimates of the transition temperature between the phases. In addition to the martensitic phase transition, we predict a new transition between the B33 and B19' phases. The role of defects in suppressing phase transformation temperatures is discussed.

Simulations↗
DOE OSTI2024

Designing a Dynamic Material via Interlocking Kraft Lignin with Ultrahigh Molecular Weight Poly(ethylene oxide)

The environmental issues stemming from plastic waste and the excessive use of petroleum-based chemicals are both concerning and urgent. To effectively address this problem, we need to adopt a comprehensive approach involving developing more sustainable and renewable materials. These materials should be capable of demonstrating similar or even better performance than functional polymers synthesized from petroleum-based chemicals. Our research aims to develop more sustainable materials by leveraging the intrinsic characteristics of a natural polymer, lignin, a byproduct of the biorefinery industries. We utilized the three-dimensional branching structure of lignin as a material framework. We employed an approach to co-reactive melt processing of kraft lignin with aliphatic flexible chains of soft cross-linkers through the reaction of the cross-linker epoxy chain ends with lignin functional groups. Our study demonstrates that the interlocked structure formed from the co-blending of kraft lignin with ultrahigh molecular weight poly(ethylene oxide) and the cross-linking of lignin chains through a solvent-free process can manipulate the macromolecular interactions and relaxation. This manipulation results in materials that exhibit a wide range of thermomechanical properties and self-healing and shape memory effects, with drastically improved stiffness in a single material. We have explored the fundamental understanding of the macromolecular chain relaxation dynamics originating from the interlocking structure formation. In conclusion, this investigation utilized various techniques, including thermal, mechanical, rheology, and quasi-elastic neutron scattering.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Combinatorial Synthesis and High-Throughput Characterization of Microstructure and Phase Transformation in Ni–Ti–Cu–V Quaternary Thin-Film Library

Ni–Ti–based shape memory alloys (SMAs) have found widespread use in the last 70 years, but improving their functional stability remains a key quest for more robust and advanced applications. Named for their ability to retain their processed shape as a result of a reversible martensitic transformation, SMAs are highly sensitive to compositional variations. Alloying with ternary and quaternary elements to fine-tune the lattice parameters and the thermal hysteresis of an SMA, therefore, becomes a challenge in materials exploration. Combinatorial materials science allows streamlining of the synthesis process and data management from multiple characterization techniques. In this study, a composition spread of Ni–Ti–Cu–V thin-film library was synthesized by magnetron co-sputtering on a thermally oxidized Si wafer. Composition-dependent phase transformation temperature and microstructure were investigated and determined using high-throughput wavelength dispersive spectroscopy, synchrotron X-ray diffraction, and temperature-dependent resistance measurements. Of the 177 compositions in the materials library, 32 were observed to have shape memory effect, of which five had zero or near-zero thermal hysteresis. These compositions provide flexibility in the operating temperature regimes that they can be used in. A phase map for the quaternary system and correlations of functional properties are discussed with respect to the local microstructure and composition of the thin-film library.

42 ENGINEERING↗
DOE OSTI2017

Computing the non-Markovian coarse-grained interactions derived from the Mori–Zwanzig formalism in molecular systems: Application to polymer melts

Memory effects are often presented during coarse-graining of a complex dynamical system. In particular, a generalized Langevin equation (GLE) for the coarse-grained (CG) system arises in the context of Mori–Zwanzig formalism. Upon a pairwise decomposition, GLE can be reformulated into its pairwise version, i.e., non-Markovian dissipative particle dynamics (DPD). GLE models the dynamics of a single coarse particle, while DPD considers the dynamics of many interacting CG particles, with both CG systems governed by non-Markovian interactions. We compare two different methods for the practical implementation of the non-Markovian interactions in GLE and DPD systems. In particular, a direct evaluation of the non-Markovian (NM) terms is performed in LE-NM and DPD-NM models, which requires the storage of historical information that significantly increases computational complexity. Alternatively, we use a few auxiliary variables in LE-AUX and DPD-AUX models to replace the non-Markovian dynamics with a Markovian dynamics in a higher dimensional space, leading to a much reduced memory footprint and computational cost. In our numerical benchmarks, the GLE and non-Markovian DPD models are constructed from molecular dynamics (MD) simulations of star-polymer melts. Results show that a Markovian dynamics with auxiliary variables successfully generates equivalent non-Markovian dynamics consistent with the reference MD system, while maintaining a tractable computational cost. Also, transient subdiffusion of the star-polymers observed in the MD system can be reproduced by the coarse-grained models. The non-interacting particle models, LE-NM/AUX, are computationally much cheaper than the interacting particle models, DPD-NM/AUX. Yet, the pairwise models with momentum conservation are more appropriate for correctly reproducing the long-time hydrodynamics characterised by an algebraic decay in the velocity autocorrelation function.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2026

Water isotope data for the TEMPEST study site, 2023-2026

This dataset contains water isotope (deuterium (dD) and oxygen (d18O)) data from porewater, experimental source water, and aquifer sources from the Terrestrial Ecosystem Manipulation to Probe the Effects of Storm Treatments (TEMPEST) experimental field site in Edgewater, MD. Samples were taken from 2023-2026 and included in file "TEMPEST_Water_Isotope_LANL_2023-2026.csv". Porewater samples were taken from 15cm depth at multiple locations in each experimental plot (i.e., control, freshwater, and saltwater). Water samples were stored in 2 ml amber glass vials with septum caps under refrigeration until analysis. A L2140-i Picarro cavity ringdown spectrometer connected to an A0211 Picarro vaporization module was used to run water samples. Standards (United States Geological Survey (USGS) 47 and 48) were used to check instrument accuracy during each run of samples. Post-processing codes were run to calculate isotopic values from raw data. Reported isotope data is post-processed. Raw data CSV files from the Picarro were processed using a Python script and output as excel files containing data calibrated to Vienna Standard Mean Ocean Water (VSMOW). Standardization is based on USGS47 and USGS48 standards that are measured before and after every 5-10 unknowns. Every measurement is comprised of 10 injections. Processing involved discarding the first 4 injections due to a known memory effect. Raw means of the last 6 injections are taken for each measurement and then corrected from the linear calibration relationship of the USGS standards expected vs measured values to obtain corrected compositions relative to VSMOW. Reported isotope data are corrected mean results.

Aquifer↗