Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mechanical reinforcement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Mechanical Properties and Microstructural Characterization of Particulate Reinforced Diboride Composites for High Temperature Leading Edge Applications

Previous work on refractory diboride composites has shown that these systems have the potential for use in high temperature leading edge applications for reusable reentry vehicles. Experiments in reentry environments have shown that these materials have multiple use temperatures greater than 1900 C. The work to be discussed focuses on three compositions: HfB2/SiC, ZrB2/SiC, and ZrB2/C/SiC. These composites have been hot pressed and their mechanical properties measured at room and elevated temperatures. Extensive microstructural characterization has been conducted on polished cross sections and the fracture surfaces have been examined to determine their failure origins.

Ellerby, Donald T.↗
NASA NTRS2001

Mechanical Properties and Microstructural Characterization of Particulate Reinforced Diboride Composites for High Temperature Leading Edge Applications

Previous work on refractory diboride composites has shown that these systems have the potential for use in high temperature leading edge applications for reusable reentry vehicles. Experiments in reentry environments have shown that these materials have multiple use temperatures greater than 1900 C. The work to be discussed focuses on three compositions: HfB2/SiC, ZrB2/SiC, and ZrB2/C/SiC. These composites have been hot pressed and their mechanical properties measured at room and elevated temperatures. Extensive microstructural characterization has been conducted on polished cross sections and the fracture surfaces have been examined to determine their failure origins.

Ellerby, Donald T.↗
NASA NTRS1996

Effects of Fiber Content on Mechanical Properties of CVD SiC Fiber-Reinforced Strontium Aluminosilicate Glass-Ceramic Composites

Unidirectional CVD SiC(f)(SCS-6) fiber-reinforced strontium aluminosilicate (SAS) glass-ceramic matrix composites containing various volume fractions, approximately 16 to 40 volume %, of fibers were fabricated by hot pressing at 1400 C for 2 h under 27.6 MPa. Monoclinic celsian, SrAl2Si2O8, was the only crystalline phase formed, with complete absence of the undesired hexacelsian phase, in the matrix. Room temperature mechanical properties were measured in 3-point flexure. The matrix microcracking stress and the ultimate strength increased with increase in fiber volume fraction, reached maximum values for V(sub f) approximately equal to 0.35, and degraded at higher fiber loadings. This degradation in mechanical properties is related to the change in failure mode, from tensile at lower V(sub f) to interlaminar shear at higher fiber contents. The extent of fiber loading did not have noticeable effect on either fiber-matrix debonding stress, or frictional sliding stress at the interface. The applicability of micromechanical models in predicting the mechanical properties of the composites was also examined. The currently available theoretical models do not appear to be useful in predicting the values of the first matrix cracking stress, and the ultimate strength of the SCS-6/SAS composites.

Bansal, Narottam P.↗
NASA NTRS1972

Fundamental mechanisms of tensile fracture in aluminum sheet undirectionally reinforced with boron filament

Results are presented from an experimental study of the tensile-fracture process in aluminum sheet unidirectionally reinforced with boron filament. The tensile strength of the material is severely limited by a noncumulative fracture mechanism which involves the initiation and sustenance of a chain reaction of filament fractures at a relatively low stress level. Matrix fracture follows in a completely ductile manner. The minimum filament stress for initiation of the fracture mechanism is shown to be approximately 1.17 GN/sq m (170 ksi), and appears to be independent of filament diameter, number of filament layers, and the strength of the filament-matrix bond. All the commonly observed features of tensile fracture surfaces are explained in terms of the observed noncumulative fracture mechanism.

Herring, H. W.↗
NASA NTRS1980

Hybridized polymer matrix composites

The extent to which graphite fibers are released from resin matrix composites that are exposed to fire and impact conditions was determined. Laboratory simulations of those conditions that could exist in the event of an aircraft crash and burn situation were evaluated. The effectiveness of various hybridizing concepts in preventing this release of graphite fibers were also evaluated. The baseline (i.e., unhybridized) laminates examined were prepared from commercially available graphite/epoxy, graphite/polyimide, and graphite/phenolic materials. Hybridizing concepts investigated included resin fillers, laminate coatings, resin blending, and mechanical interlocking of the graphite reinforcement. The baseline and hybridized laminates' mechanical properties, before and after isothermal and humidity aging, were also compared. It was found that a small amount of graphite fiber was released from the graphite/epoxy laminates during the burn and impact conditions used in this program. However, the extent to which the fibers were released is not considered a severe enough problem to preclude the use of graphite reinforced composites in civil aircraft structure. It also was found that several hybrid concepts eliminated this fiber release. Isothermal and humidity aging did not appear to alter the fiber release tendencies.

House, E. E.↗
DOE OSTI2023

Effect of recycled fibers and shredded intermediates variation on the mechanical properties and energy absorption of fiber‐reinforced composite panels

Abstract The global composite industry generates large quantities of waste which mostly ends up in landfills due to a lack of established end‐use applications for multiple waste streams. The scrap from end‐of‐life (EoL) includes manufacturing waste such as dry chopped fiber tows, loose fibers, shredded fibers from fabric textile operations, cured/semi‐cured prepregs, and fully cured composite structure waste from aircraft, automobiles, wind blades, boats, and pressure vessels. In this work, different composite waste streams were reduced to shredded intermediates, followed by simple blending, and subjected to wet compression molding to produce composite panels. The panels/plaques were tested for mechanical properties (flexure and impact), fiber‐matrix wet‐out, and property bounds. It was found that wet‐compression molding was a viable and scale‐able approach to produce recycled panels from EoL composites shredded scrap. Furthermore, full‐scale size panels for use in truck bodies and intermodal shipping container flooring were manufactured and their impact resistance was tested using a drop weight impact test. They were tested both for high‐ and low‐velocity load. In the case of high‐velocity load, the average impact load was 14,673 N; the average absorbed energy was 101.6 J; the average elastic energy was 11.7 J and the impact resistance was 1065 J/m. In the case of the low‐velocity drop weight impact test, it was found that the average impact load was 7877.358 N; the average absorbed energy was 9.718 J; the average elastic energy was 9.14 J, and the impact resistance was 184.1 J/m. The shredded composite was shown to be a candidate material for the manufacture of truck bodies and intermodal containers’ flooring panels. Highlights By using shredded intermediates from different composite waste streams, it is possible to manufacture composite panels. Wet–compression process is an appropriate technique for manufacturing recycled fiber composite panels. Regardless of the source of scrap, the mechanical properties of the produced composite panels were improved. The recycling process technology can be transformed to commercial scale to produce full‐size transportation flooring panels. A product pathway is established in consideration of lower cost and improved recyclability.

Vaidya, Uday↗
NASA NTRS2026

Influence of Processing Parameters on the Mechanical Properties of 3D Printed Borosilicate Particulate Reinforced Polymer Composites

Emerging composite materials are expanding the potential of additive manufacturing and enabling applications previously restricted by traditional manufacturing methods. The multi-phase nature of these composite materials combined with the complex in-ternal geometry of additively manufactured parts have enabled unique behavior, and potentially new applications. Additionally, these materials can be pyrolyzed to create dense metal, ceramic, and glass parts with geometries typically not achievable by tra-ditional processes. Additive manufacturing of borosilicate glass-based systems can open new applications in nuclear engineering, astronomy, and bone regrowth therapy. To elucidate the process-parameter relationship of borosilicate-polylactic acid (PLA) composites, mechanical testing was conducted and compared with a pure polylactic acid polymer baseline. Test specimens were fabricated by fused-filament fabrication with minimal post-processing. Yield strength, ultimate strength, and elastic modulus were calculated from stress-strain curves. Optical and scanning electron microscopy were conducted to observe the specimen microstructure before and after testing. The highest compressive yield strength for the composite was 28.22 MPa, and the highest compressive yield strength for PLA was 49.30 MPa. Print orientation was found to benefit the composite material but have a detrimental effect on the pure matrix material. An elastic modulus of 2.66 GPa was recorded for the borosilicate-PLA composite at 100% infill, 1 shell wall, and layer lines parallel to compression axis. Microscopy revealed that lower modulus composite specimens had the particulates re-distributed within the matrix. Tensile testing was done according to a polymer testing standard, which caused difficulties obtaining consistent fracture within the gauge length.

mechanical testing↗
NASA NTRS1985

Fracture surface analysis in composite and titanium bonding

To understand the mechanical properties of fiber-reinforced composite materials, it is necessary to understand the mechanical properties of the matrix materials and of the reinforcing fibers. Another factor that can affect the mechanical properties of a composite material is the interaction between the fiber and the matrix. In general, composites with strong fiber matrix bonding will give higher modulus, lower toughness composites. Composites with weak bonding will have a lower modulus and more ductility. The situation becomes a bit more complex when all possibilities are examined. To be considered are the following: the properties of the surface layer on the fiber, the interactive forces between polymer and matrix, the surface roughness and porosity of the fiber, and the morphology of the matrix polymer at the fiber surface. In practice, the surface of the fibers is treated to enhance the mechanical properties of a composite. These treatments include anodization, acid etching, high temperature oxidation, and plasma oxidation, to name a few. The goal is to be able to predict the surface properties of carbon fibers treated in various ways, and then to relate surface properties to fiber matrix bonding.

Devilbiss, T. A.↗
NASA NTRS1992

A mechanism responsible for reducing compression strength of through-the-thickness reinforced composite material

A study was conducted to identify one of the mechanisms that contributes to the reduced compression strength of composite materials with through-the-thickness (TTT) reinforcements. In this study a series of thick (0/90) laminates with stitched and integrally woven TTT reinforcements were fabricated and statically tested. In both the stitching and weaving process a surface loop of TTT reinforcement yarn is created between successive TTT penetrations. It was shown that the surface loop of the TTT reinforcement 'kinked' the in-plane fibers in such a manner that they were made ineffective in carrying compressive load. The improvement in strength by removal of the surface loop and 'kinked' in-plane fibers was between 7 and 35 percent.

Farley, Gary L.↗
DOE OSTI2026

Cyclic olefin copolymer-based reinforced anion exchange membranes for water electrolyzers

Anion exchange membranes (AEMs) have emerged as a promising technology for water electrolysis in hydrogen production since they offer significant cost reduction in choices of electrocatalysts and bipolar plates. However, AEMs satisfying multiple requirements of high ionic conductivity, good chemical stability, robust mechanical properties, scalable synthesis, and low manufacturing costs are rare. Herein, we introduce quaternary ammonium functionalized cyclic olefin copolymers (COCs) as a new class of chemically stable and low-cost AEM materials. To further enhance the mechanical robustness, we prepared reinforced composite AEMs by impregnating the ionically functionalized COC into a mechanically robust matrix. The resulting reinforced composite membrane exhibits a high hydroxide conductivity of 127 mS cm −1 and excellent mechanical strength. In water electrolyzers, the MEA demonstrated outstanding performance, achieving a current density of 2.24 A cm −2 at 1.8 V, attributable to high conductivity, enhanced mechanical properties, and good alkaline stability of the composite membrane. These results indicate that the COC-based AEMs demonstrate good potential for application in AEM electrolyzers.

08 HYDROGEN↗
DOE OSTI2020

Influence of Silane Coupling Agents on Filler Network Structure and Stress-Induced Particle Rearrangement in Elastomer Nanocomposites

Filled rubber materials are key in many technologies having broad impact on the economy and sustainability, the most obvious being tire technology. Adding filler dramatically improves the strength of rubber by reinforcement and tailoring the type of filler and the chemistry of the interface between filler and rubber matrix is important for optimizing performance metrics such as fuel efficiency. In a highly loaded, silica-filled, crosslinked model rubber closely mimicking commercial materials, both the filler network structure and the dynamics of the silica filler particles change when the silica surface is modified with silane coupling agents. Reduction in size scales characteristic of the structure are quantified using ultra-small-angle X-ray scattering (USAXS) measurements and the particle dynamics probed with X-ray photon correlation spectroscopy (XPCS). While the structure averaged over the scattering volume changes little with aging after step strain, the dynamics slow appreciably in a manner that varies with the treatment of the silica filler. The evolution of filler particle dynamics depends on the chemical functionality at the silica surface and observing these differences suggests a way of thinking about the origins of hysteresis in nanoparticle-reinforced rubbers. These microscopic filler dynamics are correlated with the macroscopic stress relaxation of the filled materials. The combination of static and dynamic X-ray scattering techniques with rheological measurements is a powerful approach for elucidating the microscopic mechanisms of rubber reinforcement.

36 MATERIALS SCIENCE↗
DOE OSTI2024

MOLLER Spectrometer Magnet Design With Measured Mechanical Properties of Irradiated S2-Glass Reinforced Cyanate Ester Resin at Elevated Temperature

Here, the aim of this study was to retire the risk of maintaining the integrity of S2-glass reinforced CTD-403 (a cyanate ester resin) that is exposed to radiation and elevated temperature over the life of the measurement of a lepton–lepton electroweak reaction (MOLLER) experiment in experimental Hall A at Jefferson Lab, Newport News, VA. In this article, the shear strength and flexural modulus of irradiated S2-glass reinforced CTD-403 specimens were measured at 65 °C (the magnets are to operate at less than 65 °C) under two scenarios: vacuum and gaseous nitrogen. The testing method is the short-beam shear (SBS) test according to ASTM D2344. The specimens were exposed to neutrons and gamma rays up to 124 MGy. The results show that specimens have excellent resistance against radiation, only 23% degradation of apparent shear strength with 124 MGy at 65 °C under vacuum. At the highest dose areas of the coils, tungsten plates are used to reduce the radiation dose to the resin system. The conclusion is that S2-glass reinforced CTD-403 is well-suited for electrical insulation of MOLLER magnets.

36 MATERIALS SCIENCE↗
NASA NTRS1974

A Study of the Effect of Adhesive and Matrix Stiffnesses on the Axial, Normal, and Shear Stress Distributions of a Boron-epoxy Reinforced Composite Joint

The mechanical properties of a symmetrical, eight-step, titanium-boron-epoxy joint are discussed. A study of the effect of adhesive and matrix stiffnesses on the axial, normal, and shear stress distributions was made using the finite element method. The NASA Structural Analysis Program (NASTRAN) was used for the analysis. The elastic modulus of the adhesive was varied from 345 MPa to 3100 MPa with the nominal value of 1030 MPa as a standard. The nominal values were used to analyze the stability of the joint. The elastic moduli were varied to determine their effect on the stresses in the joint.

Howell, W. E.↗
NASA NTRS1982

Effect of Ionizing Radiation on the Mechanical and Structural Properties of Graphite Fiber Reinforced Composites

Graphite/epoxy (T300/5208) and graphite/polyimide composites (C6000/PMR 15) were exposed to various levels of 0.5 MeV electron radiation with the maximum dose being 10,000 Mrad. A three point bending test was used to evaluate the ultimate stress and modulus of the composites. In all composites except transverse samples of C6000/PMR 15 ultimate stress values remained approximately constant or increased slightly. The modulus values remained approximately constant for all composite types regardless of the radiation level. Interfacial aspects of composites were studied. Interlaminar shear tests were performed on T300/5208 and C6000/PMR 15 composites irradiated to 10,000 Mrad. There was an initial increase in interlaminar shear strength (up to 1,000 Mrad) followed by a sharp decrease with further radiation exposure. Using scanning electron microscopy no visual differences in the mode of fracture could be detected between ruptured control samples and those exposed to various levels of radiation. Electron spectroscopy for chemical analysis (ESCA) revealed little change in the surface elements present in control and highly irradiated T300/5208 composite samples.

Wolf, Kay Woodroof↗
NASA NTRS1991

Micromechanical analysis of the failure process in ceramic matrix composites

An analysis of the effectiveness of fiber reinforcement in brittle matrix composites is presented. The analytical method allows consideration of discrete fiber distribution and examination of the development of crack growth parameters on the microscale. The problem associated with bridging zone development is addressed here; therefore, the bridging zone is considered to be smaller than the main preexisting crack, and the small scale approach is used. The mechanics of the reinforcement is accurately accounted for in the process zone of a growing crack. Closed form solutions characterizing the initial failure process are presented for linear and nonlinear force-fiber pullout displacement relationships. The implicit exact solution for the extended bridging zone is presented as well.

Rubinstein, Asher A.↗