Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials synthesis and processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Facet-selective morphology-controlled remote epitaxy of ZnO microcrystals via wet chemical synthesis

We report on morphology-controlled remote epitaxy via hydrothermal growth of ZnO micro- and nanostructure crystals on graphene-coated GaN substrate. The morphology control is achieved to grow diverse morphologies of ZnO from nanowire to microdisk by changing additives of wet chemical solution at a fixed nutrient concentration. Although the growth of ZnO is carried out on poly-domain graphene-coated GaN substrate, the direction of hexagonal sidewall facet of ZnO is homogeneous over the whole ZnO-grown area on graphene/GaN because of strong remote epitaxial relation between ZnO and GaN across graphene. Atomic-resolution transmission electron microscopy corroborates the remote epitaxial relation. The non-covalent interface is applied to mechanically lift off the overlayer of ZnO crystals via a thermal release tape. The mechanism of facet-selective morphology control of ZnO is discussed in terms of electrostatic interaction between nutrient solution and facet surface passivated with functional groups derived from the chemical additives.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Finned-tube-integrated modular thermal storage systems for HVAC load modulation in buildings

While there is considerable focus on latent-based thermal energy storage (TES) systems, the low thermal conductivity of phase change materials (PCMs) remains a critical concern. Many approaches to enhance PCM conductivity either require complicated synthesis processes or are cost prohibitive. In this study, we investigate finned-tube modular TES systems, which are simple in design, easy to manufacture, and cost-effective due to their standard materials and components. The study includes detailed modeling and experimentation of two devices containing similar amounts of PCM but different fin spacings. The study reveals that having more fins does not necessarily increase the TES thermal performance because the reduction in the PCM volume fraction can reduce the TES volumetric and specific energy densities. We find that larger fin spacings provide a higher specific energy for lower C rates (<1C), while smaller fin spacings provide a higher specific energy for higher C rates (>1C).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Laser writing of nitrogen-doped silicon carbide for biological modulation

Conducting or semiconducting materials embedded in insulating polymeric substrates can be useful in biointerface applications; however, attainment of this composite configuration by direct chemical processes is challenging. Laser-assisted synthesis has evolved as a fast and inexpensive technique to prepare various materials, but its utility in the construction of biophysical tools or biomedical devices is less explored. Here, we use laser writing to convert portions of polydimethylsiloxane (PDMS) into nitrogen-doped cubic silicon carbide (3C-SiC). The dense 3C-SiC surface layer is connected to the PDMS matrix via a spongy graphite layer, facilitating electrochemical and photoelectrochemical activity. We demonstrate the fabrication of arbitrary two-dimensional (2D) SiC-based patterns in PDMS and freestanding 3D constructs. To establish the functionality of the laser-produced composite, we apply it as flexible electrodes for pacing isolated hearts and as photoelectrodes for local peroxide delivery to smooth muscle sheets.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Temperature-Swing Synthesis of Large-Size Single-Crystal LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode Materials

Single-crystal lithium-nickel-manganese-cobalt-oxide (SC-NMC) has recently emerged as a promising battery cathode material due to its outstanding cycle performance and mechanical stability over the tradional polycrystalline NMC. It is favorable to further increase the grain size of SC-NMC particles to achieve a higher volumetric energy density and minimize surface-related degradations. However, the preparation of large-size yet high performance SC-NMC particles faces a challenge in choosing a suitable temperature for sintering. High temperature promotes grain growth but induces cation mixing that negatively impacts the electrochemical performance. Here we report a temperature-swing sintering (TSS) strategy with two isothermal stages that fulfils the needs for grain growth and structural ordering sequentially. A high-temperature sintering is first used for a short period of time to increase grain size and then the reaction temperature is lowered and kept constant for a longer period of time to improve structural ordering and complete the lithiation process. SC-LiNi 0.6 Mn 0.2 Co 0.2 O 2 materials prepared via TSS exhibit large grain size (~4 μm), a low degree of cation mixing (~0.9%), and outperform the control samples prepared by the conventional sintering method. Furthermore, this work highlights the importance of understanding the process-structure-property relationships and may guide the synthesis of other SC Ni-rich cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2022

Materials Dynamics

The Materials Dynamics area of leadership focuses on understanding process-structure-properties-performance (PSPP) relationships for the extreme conditions of dynamic loading. This research encompasses controlled synthesis of materials to meet dynamic performance requirements and entails computational coupling across length and time scales for three-dimensional microstructure modeling. For this leadership area, we define dynamic loading as strain rates ≥ 10 3 /s and often, high pressures. A key grand challenge of this area is to predict and measure the evolution of microstructural phases, defect structures, and electronic structure under dynamic conditions while also measuring local temperature to understand transition states. Solving this challenge will require agile, multi-dimensional data analysis and interpretation capability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Superhard Materials: Advances in the Search and Synthesis of New Materials

Materials with superior hardness can be categorized as ultrahard (Vickers hardness, H v ≥ 80 GPa) and superhard (H v ≥ 40 GPa). These materials are commonly used as cutting tools and abrasives in the machining and manufacturing industries. With its extreme hardness, diamond is the best known and most used ultrahard material for industrial applications. However, it is ineffective at cutting and drilling ferrous alloys due to diamond's high reactivity with iron and poor thermal stability in air. Additionally, the synthesis of diamond requires both high pressure (HP) and high temperature, making it an expensive process. These limitations have driven the search for alternative superhard materials that are capable of cutting steels and other materials at lower costs. This article reviews the concept of hardness and summarizes advancements in the synthesis and mechanical properties of hard materials. It begins with a review of methods to measure hardness, adding HP diffraction methods to more conventional hardness measurements. It then considers new ultrahard materials that exist within the B–C–N ternary system, with hardness approaching diamond but improved chemical stability. Finally, it surveys superhard nitrides, oxides, and borides as potential alternative materials, focusing on transition metal boride systems where the synthesis can be readily achieved at ambient pressure and scaled for industrial applications. We hope that this article serves as an overview of hard materials and guide for the comparison of data reported in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Selectivity mechanisms of ion intercalation in Prussian blue analogs

Prussian blue analogs (PBAs) are a family of materials with facile, reversible, and selective ion transport capability for various ions via electrochemical intercalation, owing to their vacancy structure. The large tunable compositional space of PBAs allows for manipulation of intercalation behavior and selectivity by controlling structural vacancy level through choice of transition metal centers and modifications to the synthesis process. However, a lack of understanding of the mechanisms of ion selectivity hinders the material’s design process. Here, for this work, we investigated the origins of ion selectivity using a model PBA, copper hexacyanoferrate, and focused on eight technologically and biologically prominent ions, for which we determined a sequence of selectivity: Rb + > K + > Na + > Ba 2+ > Sr 2+ ≈ Ca 2+ > Mg 2+ > Li + . We provide electrochemical, structural, and redox evidence of strong correlation between the ion identity, the dominant charge-compensating redox, and preferred occupancy site. Specifically, using synchrotron anomalous X-ray diffraction (AXRD), we reveal that monovalent ions exhibit significant association with the corner sites of the unit cell and iron redox, whereas divalent ions display affinity toward the center site with higher ratios of copper redox. Informed by selectivity results, we applied CuHCFe to Li purification and achieved 99.9% purity. Our findings demonstrate an approach to elucidating ion intercalation behavior in order to distinguish and manipulate material properties to optimize separation performance.

Prussian blue analog↗
DOE OSTI2026

Understanding Solvent-Induced Glass Transition in Polymer Thin Films Using Absorption–Desorption Isotherms

The fundamental thermodynamic and mechanical underpinnings of polymer thin films exposed to solvent vapor are critical for the development of advanced nanolithography and high-performance coatings. This work investigates the solvent− polymer interactions of glassy thin films by using the solvent absorption−desorption isotherms. An analogous relationship to the Flory−Fox equation was observed between solvent−induced glass transition, swelling, Flory−Huggins interaction parameter, and molecular weight. Isothermal swelling measurements revealed that the glass transition trends are more robust in the absorption curve compared to desorption, contrary to previous reports. Excess osmotic pressure analysis of the isotherm provides a measure of the degree of physical aging in thin films annealed below the glass transition. This is further validated in the ordering of block copolymer (BCP) films annealed at low solvent activity. In agreement with the thermal analysis, free-surface plasticization effects become the most prominent below 100 nm. However, solvent annealing is largely dependent on solvent mass transport, as made evident by the strong dependence on solvent viscosity. From these observations, four general types of isotherms are identified that graphically capture distinct solvent−polymer interaction regimes. More broadly, these results inform solvent vapor annealing-induced self-assembly, sequential infiltration synthesis, membrane-based separations, adsorptive processes, and swelling-based responsive materials design.

Hendeniya, Nayanathara [Iowa State Univ., Ames, IA↗
DOE OSTI2023

Li–Mn–O Li-rich cation disordered rock-salt cathode materials do not undergo reversible oxygen redox during cycling

An in-depth study of “Li 4 Mn 2 O 5 ”, a nanocomposite of Li 2 O and Li 4-x Mn 2 O 5 with a disordered rock salt structure (LMO), was conducted to determine the origins of the observed anomalously high charge and discharge capacity in lithium cells, which can exceed 350 mA h g -1 . Using soft and hard X-ray absorption spectroscopy (XAS), mapping of resonant inelastic X-ray scattering (mRIXS), and X-ray Raman spectroscopy (XRS), it was determined that electrochemical decomposition of Li 2 O upon charge and reduction of Mn to below 3+ during discharge is responsible for the capacities that are observed, with no evidence of contributions from reversible oxygen redox. Here, the over-reduction is exacerbated when charging limits of 4.5–4.8 V are used due to side reactions between electrolytic solution and the highly oxidized active material. These side reactions result in dissolution of Mn at room temperature and release of oxygen and other gases during initial cycles, which, in turn, cause rapid capacity fading. This is accompanied by evolution of the voltage profile upon cycling towards one that resembles that of manganese oxide spinels. The cycling behavior can be improved somewhat by reducing the upper voltage limit, although this results in a diminishment of the discharge capacities below 200 mA h g -1 . By adding various amounts of spinel LiMn 2 O 4 during synthesis, it was possible to produce LMOs with rock salt structures having significantly improved cycling behavior but still having capacities in excess of 250 mA h g -1 . An optimized modified material also exhibits better rate capability and much less gas evolution during initial cycles than the unmodified LMO. Interestingly, as-made modified materials generally exhibited lower than expected average Mn oxidation states attributable to oxygen loss during the synthesis process, as well as higher capacities than expected based on their manganese contents. The oxygen loss during processing may reduce the activity of the remaining oxygen and account for the lower reactivity of the spinel-modified material.

25 ENERGY STORAGE↗
DOE OSTI2026

Automation of Nanoparticle Synthesis Processes in a Plasma Environment Using LabVIEW

This work presents an automated control system for the synthesis of nanomaterials by plasma-enhanced chemical vapor deposition (PECVD), implemented using the LabVIEW software environment. The main objective of the study is to develop an integrated hardware-software platform that enables sequential control of the key stages of the PECVD process, including vacuum chamber preparation, pressure monitoring, working gas supply, plasma ignition, power matching, cyclic nanomaterial growth, and optical monitoring of nanoparticles in the plasma environment. The use of LabVIEW made it possible to integrate actuator control, experimental parameter acquisition, and realtime process visualization within a single automated system. The automated cycle begins with evacuation of the reaction chamber to a predefined base pressure. Transition to the next stage is permitted only after the specified pressure threshold has been reached, ensuring reproducible initial conditions for each experiment. The program then controls the supply of the working gas through mass flow controllers (MFCs). In this work, two gas-flow control modes were considered: analog control using a 0-5 V voltage signal and digital communication via RS-232 interface. It was shown that the analog approach requires accurate scaling of the control voltage, since applying 5 V corresponds to full-scale opening of the controller and results in the maximum gas flow. In contrast, the RS232 interface enables the gas flow rate to be specified directly in sccm, improving the accuracy, flexibility, and convenience of gas-environment control. After pressure stabilization, LabVIEW initiates RF plasma ignition and executes the RF matching algorithm aimed at minimizing reflected power and improving the stability of the plasma process. A separate software module implements the cyclic nanomaterial growth mode, in which the plasma-on time, plasma duration, and total number of synthesis cycles are predefined. This approach makes it possible to control material accumulation on the substrate and to correlate the process parameters with the morphological characteristics of the resulting nanostructures. The final module of the system is designed for optical monitoring of the nanoparticle cloud density in dusty plasma. For this purpose, the change in the intensity of laser radiation passing through the plasma region is recorded using a photodetector and a Keithley 2401 measuring unit connected to LabVIEW via RS-232 interface. The difference between the initial and modified optical signal intensity is used as a diagnostic parameter characterizing the formation and temporal evolution of nanoparticles. The developed system demonstrates that LabVIEW can be effectively applied not only for the automation of individual instruments, but also for the implementation of a complete digital control cycle for PECVD-based nanomaterial synthesis.

PECVD↗
DOE OSTI2021

Materials Based on Technical Bulk Lignin

Lignin is the second most abundant biopolymer and the main source of aromatic structures on earth. Lignin has long been produced as a byproduct of the pulping process and utilized in low value-added applications like heat. However, lignin has received increased attention in recent years to improve its value through various chemical processes. This Review compiles recent progress in synthesis, properties, and applications of lignin-based materials. The lignin for material applications can often be classified into three categories: technical bulk lignin (TBL), lignin-derived oligomers (LDOs), and lignin-derived phenols (LDPs). Furthermore, this Review focuses on the chemical modifications of TBLs and their applications in novel smart materials like self-healing, stimulus responsive, and shape memory polymers. The conversion of TBL to polymers can be briefly divided into two steps: (1) introduction of polymerizable functional groups into the lignin backbone and (2) polymerization that achieves desired materials. Both lignin functionalization and polymerization approaches are discussed in detail. As such, this work attempts to provide a comprehensive overview that highlights the importance of these approaches for the utilization of the abundant but largely ignored biopolymer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Plasma-driven solution electrolysis

Plasmas interacting with liquids enable the generation of a highly reactive interfacial liquid layer due to a variety of processes driven by plasma-produced electrons, ions, photons, and radicals. These processes show promise to enable selective, efficient, and green chemical transformations and new material synthesis approaches. While many differences are to be expected between conventional electrolysis and plasma–liquid interactions, plasma–liquid interactions can be viewed, to a first approximation, as replacing a metal electrode in an electrolytic cell with a gas phase plasma. For this reason, we refer to this method as plasma-driven solution electrochemistry (PDSE). In this Perspective, we address two fundamental questions that should be answered to enable researchers to make transformational advances in PDSE: How far from equilibrium can plasma-induced solution processes be driven? and What are the fundamental differences between PDSE and other more traditional electrochemical processes? Different aspects of both questions are discussed in five sub-questions for which we review the current state-of-the art and we provide a motivation and research vision.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

A Review of Scalable Hexagonal Boron Nitride ( h -BN) Synthesis for Present and Future Applications

Hexagonal boron nitride (h-BN) is a layered inorganic synthetic crystal exhibiting high temperature stability and high thermal conductivity. As a ceramic material it has been widely used for thermal management, heat shielding, lubrication, and as a filler material for structural composites. Recent scientific advances in isolating atomically thin monolayers from layered van der Waals crystals to study their unique properties has propelled research interest in mono/few layered h-BN as a wide bandgap insulating support for nanoscale electronics, tunnel barriers, communications, neutron detectors, optics, sensing, novel separations, quantum emission from defects, among others. Realizing these futuristic applications hinges on scalable cost-effective high-quality h-BN synthesis. Here, in this work, the authors review scalable approaches of high-quality mono/multilayer h-BN synthesis, discuss the challenges and opportunities for each method, and contextualize their relevance to emerging applications. Maintaining a stoichiometric balance B:N = 1 as the atoms incorporate into the growing layered crystal and maintaining stacking order between layers during multi-layer synthesis emerge as some of the main challenges for h-BN synthesis and the development of processes to address these aspects can inform and guide the synthesis of other layered materials with more than one constituent element. Finally, the authors contextualize h-BN synthesis efforts along with quality requirements for emerging applications via a technological roadmap.

2D materials↗
DOE OSTI2024

Removing Fluoride from Double Four-Membered Rings Yielding Defect-Free Zeolites under Mild Conditions Using Ozone

We have investigated ozone treatment of as-made LTA zeolites under mild temperature conditions (175 °C) using experiments and periodic DFT as a method of energy savings and engineering defects such as silanol nests in comparison with conventional calcination at 550 °C. We have studied ozone treatment on LTA samples synthesized with 1,2-dimethyl-3-(4-methylbenzyl) imidazolium (denoted as “BULKY”) as the primary organic structure-directing agent (OSDA) and with various amounts of tetramethylammonium (TMA) as a secondary OSDA. Ozone treatment of LTA-BULKY at 175 °C was found to give defect-free, pristine LTA materials as determined by 29 Si NMR, 13 C NMR, Raman spectra, and DFT to assign the spectra. This represents a significant and unexpected finding: that fluoride ions can be completely removed from double four-membered rings (D4Rs) under such mild conditions. Furthermore, ozone treatment of LTA-BULKY-TMA samples removed BULKY but left behind TMA/F, giving a new and more diverse structural landscape of Si environments in LTA. Ab initio MetaDynamics calculations provide pathways with relatively low barriers, explaining how fluoride ions can be removed from D4Rs, leaving behind defect-free LTA materials under mild conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Inverse iron oxide/metal catalysts from galvanic replacement

Key chemical transformations require metal and redox sites in proximity at interfaces; however, in traditional oxide-supported materials, this requirement is met only at the perimeters of metal nanoparticles. We report that galvanic replacement can produce inverse FeO x /metal nanostructures in which the concentration of oxide species adjoining metal domains is maximal. The synthesis involves reductive deposition of rhodium or platinum and oxidation of Fe 2+ from magnetite (Fe 3 O 4 ). We discovered a parallel dissolution and adsorption of Fe 2+ onto the metal, yielding inverse FeO x -coated metal nanoparticles. This nanostructure exhibits the intrinsic activity in selective CO 2 reduction that simple metal nanoparticles have only at interfaces with the support. By enabling a simple way to control the surface functionality of metal particles, our approach is not only scalable but also enables a versatile palette for catalyst design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Heteroepitaxial chemistry of zinc chalcogenides on InP nanocrystals for defect-free interfaces with atomic uniformity

Heteroepitaxy on colloidal semiconductor nanocrystals is an essential strategy for manipulating their optoelectronic functionalities. However, their practical synthesis typically leads to scattered and unexpected outcomes due to the intervention of multiple reaction pathways associated with complicated side products of reactants. Here, the heteroepitaxy mechanism of zinc chalcogenide initiated on indium phosphide (InP) colloidal nanocrystals is elucidated using the precursors, zinc carboxylate and trialkylphosphine selenide. The high magnetic receptivity of 77 Se and the characteristic longitudinal optical phonon mode of ZnSe allowed for monitoring the sequence of epilayer formation at the molecular level. The investigation revealed the sterically hindered acyloxytrialkylphosphonium and diacyloxytrialkylphosphorane to be main intermediates in the surface reaction, which retards the metal ion adsorption by a large steric hindrance. The transformation of adsorbates to the crystalline epilayer was disturbed by surface oxides. Raman scattering disclosed the pathway of secondary surface oxidation triggered by carboxylate ligands migrated from zinc carboxylate. The surface-initiated heteroepitaxy protocol is proposed to fabricate core/shell heterostructured nanocrystals with atomic-scale uniformity of epilayers. Despite the large lattice mismatch of ZnS to InP, we realised a uniform and interface defect-free ZnS epilayer (~0.3 nm thickness) on InP nanocrystals, as evidenced by a high photoluminescence quantum yield of 97.3%.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Selective reduction in epitaxial SrFe 0.5 Co 0.5 O 2.5 and its reversibility

Oxygen-vacancy engineering in transition metal oxides enables programmable functionalities by modulating the valence states and local coordination of constituents. Here, we report the selective reduction of cobalt ions in epitaxial SrFe 0.5 Co 0.5 O 2.5 thin films under reducing gas environments, while iron ions remain unchanged. X-ray absorption spectroscopy reveals an absorption edge shift of 1.65 eV in the Co L-edge upon reduction, and multiplet simulations estimate a decrease in the average Co valence from Co 2.91+ to Co 2.00+ . This site- and element-specific reduction leads to the formation of a structurally distinct oxygen-deficient phase stabilized by oxygen vacancies at tetrahedral sites, as confirmed by density functional theory. Optical spectroscopy reveals an increase in the bandgap from 2.47 eV to 3.04 eV, accompanied by enhanced transparency. Furthermore, simultaneous in situ diffraction and transport measurements confirm fully reversible redox-driven transitions among three phases: reduced defective perovskite, brownmillerite, and oxygen-rich perovskite phases. These findings demonstrate that selective redox control in multi-cation oxides enables the realization of chemically and functionally distinct oxygen-deficient phases.

Fuel cells↗