Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material toxicity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A review of Sb 2 Se 3 photovoltaic absorber materials and thin-film solar cells

Energy generated from environmentally friendly, cost-effective solar cells is a key aspect for developing a clean renewable-energy economy. Non-toxic and Earth-abundant materials with high absorption coefficient (>10 5 cm -1 ) and optimal bandgap (1-1.5 eV) have received great attention as photovoltaic (PV) absorber layers during the last few decades. Among them, antimony selenide (Sb 2 Se 3 ) has been a promising PV absorber, with steadily increasing power-conversion efficiency (PCE) compared to other emerging compounds. Very recent studies showed that high-quality ZnO:Al/ZnO/CdS/TiO 2 /Sb 2 Se 3 /MoSe 2 /Mo devices with PCE of 9.2% can be fabricated using cost-effective novel compounds. Considering these recent advances, this article provides an overview of the material properties of Sb2Se3 thin films and the recent progress made with Sb 2 Se 3 -based solar cells. Furthermore, analysis of Sb 2 Se 3 -based thin-film solar cells has also shown that the devices have relatively good light management due to their suitable bandgap and high absorption coefficient, whereas carrier management, i.e. collection efficiency of photo-generated carriers, needs significant improvement. Overall, this study provides background knowledge on material properties and device performance and suggests main research directions to overcome the limiting factors of solar cell performance.

14 SOLAR ENERGY↗
NASA NTRS1974

Development of spacecraft toxic gas removal agents

The development of agents suitable for removal of CO, NH3, NO2 SO2, and other spacecraft contaminants was approached. An extensive technology review was conducted, yielding a large number of potentially useful materials and/or concepts. Because the two toxic gases of greatest interest, CO and NH3, suggested the use of catalysis principles emphasis was placed on the intestigation of transition metals on various supports. Forty-three materials were prepared or obtained and 25 were tested. Gas chromatographic techniques were used to find seven candidates that effectively managed various combinations of the four toxic gases: none managed all. These candidates included six transition metal-containing preparations and a supported LiOH material. Three commercial charcoals showed some efficiency for the toxic gases and may constitute candidates for enhancement by doping with transition metals.

Moore, R. S.↗
NASA NTRS1971

Toxicology of spacecraft materials

The procedures for determining the toxicity of products outgassed from spacecraft structures are discussed. The test equipment involved in the tests and the criteria for acceptability are described. The use of animals as the final step in determining toxicity of a spacecraft environment is explained.

Harris, E. S.↗
NASA NTRS2018

Polyurethane Microparticles for Stimuli Response and Reduced Oxidative Degradation in Highly Porous Shape Memory Polymers

Shape memory polymers (SMPs) have been found to be promising biomaterials for a variety of medical applications; however, the clinical translation of such technology is dependent on tailorable properties such as gravimetric changes in degradation environments. For SMPs synthesized from amino-alcohols, oxidation resulting in rapid mass loss may be problematic in terms of loss of material functionality as well as toxicity and cytocompatibility concerns. Control of gravimetric changes was achieved through the incorporation of small molecule antioxidants, either directly into the polymer matrix or included in microparticles to form a SMP composite material. Direct incorporation of small molecule antioxidants, such as phenolic alcohols, was found to alter shape memory attributes and increase elastic modulus at the expense of the strain to failure. Such changes could not ensure retention of the antioxidants and therefore did not increase oxidative stability. However, the inclusion of antioxidants in microparticles was found to produce materials with similar thermomechanical and shape memory properties while increasing oxidative resistance compared to controls. The microparticle composite SMPs also act as a platform for environmental sensing, such as pH-dependent fluorescence shifts and payload release, as demonstrated by fluorescent dyes and the release of antioxidants. The use of polyurethane-urea microparticles in porous SMPs is demonstrated to increase biostability of the materials, by approximately 25%, and ultimately extend their lifespan for use in aneurysm occlusion as determined through calculated in vivo degradation rates corresponding to a porcine aneurysm environment.

Weems, A. C.↗
NASA NTRS1974

Fire-resistant aircraft materials development and evaluation program

The overall objectives of this program are to provide a more fire-resistant commercial aircraft interior and to improve the fuselage insulation barrier between the cabin interior and an exterior fuel fire. Significant secondary objectives are to reduce the smoke and toxic gas production of the materials and to meet the end item use requirements pertaining to wearability, color fastness, and aesthetic appeal. It is shown that the fuselage insulation materials must meet stringent requirements pertaining to acoustic attenuation, low density, and water repellency.

Bricker, R. W.↗
DOE OSTI2021

Recruiting Perovskites to Degrade Toxic Trinitrotoluene

Everybody knows TNT, the most widely used explosive material and a universal measure of the destructiveness of explosions. A long history of use and extensive manufacture of toxic TNT leads to the accumulation of these materials in soil and groundwater, which is a significant concern for environmental safety and sustainability. Reliable and cost-efficient technologies for removing or detoxifying TNT from the environment are lacking. Despite the extreme urgency, this remains an outstanding challenge that often goes unnoticed. We report here that highly controlled energy release from explosive molecules can be accomplished rather easily by preparing TNT–perovskite mixtures with a tailored perovskite surface morphology at ambient conditions. These results offer new insight into understanding the sensitivity of high explosives to detonation initiation and enable many novel applications, such as new concepts in harvesting and converting chemical energy, the design of new, improved energetics with tunable characteristics, the development of powerful fuels and miniaturized detonators, and new ways for eliminating toxins from land and water.

36 MATERIALS SCIENCE↗
NASA NTRS1978

Fire testing in the Boeing 707 cabin section

The goal of a FIREMEN funded contract is the definition of a laboratory test method ranking airplane interior materials by probable performance in post-crash and in-flight fires. A major task is the relation of laboratory results to full scale data. A large test facility for testing materials to the thermal threat of fuel fed and interior fires was developed with quartz lamps and a propane burner in a twenty foot fuselage section. A method was developed to analyze full scale data for the apparent heat, smoke and toxicant release rates of the material tested.

Tustin, E. A.↗
DOE OSTI2020

Lithium ion battery with thermal runaway protection

Lithium ion batteries are provided that include materials that provide advantageous endothermic functionalities contributing to the safety and stability of the batteries. The endothermic materials may include a ceramic matrix incorporating an inorganic gas-generating endothermic material. If the temperature of the lithium ion battery rises above a predetermined level, the endothermic materials serve to provide one or more functions to prevent and/or minimize the potential for thermal runaway, e.g., thermal insulation (particularly at high temperatures); (ii) energy absorption; (iii) venting of gases produced, in whole or in part, from endothermic reaction(s) associated with the endothermic materials, (iv) raising total pressure within the battery structure; (v) removal of absorbed heat from the battery system via venting of gases produced during the endothermic reaction(s) associated with the endothermic materials, and/or (vi) dilution of toxic gases (if present) and their safe expulsion from the battery system.

25 ENERGY STORAGE↗
DOE OSTI2020

Inorganic Halide Double Perovskites with Optoelectronic Properties Modulated by Sublattice Mixing

All-inorganic halide double perovskites have emerged as a promising class of materials that are potentially more stable and less toxic than lead-containing hybrid organic-inorganic perovskite optoelectronic materials. In this work, 311 cesium chloride double perovskites (Cs 2 BB'Cl 6 ) were selected from a set of 903 compounds as likely being stable on the basis of a statistically learned tolerance factor (t) for perovskite stability. First-principles calculations on these 311 double perovskites were then performed to assess their stability and identify candidates with band gaps appropriate for optoelectronic applications. We predict that 261 of the 311 Cs 2 BB'Cl 6 compounds are likely synthesizable on the basis of a thermodynamic analysis of their decomposition to competing compounds (decomposition enthalpy <0.05 eV/atom). Of these 261 likely synthesizable compounds, 47 contain no toxic elements and have direct or nearly direct (within 100 meV) band gaps between 1 and 3 eV, as computed with hybrid density functional theory (HSE06). Within this set, we identify the triple-alkali perovskites Cs 2 [Alk] + [TM] 3+ Cl 6 , where Alk is a group 1 alkali cation and TM is a transition-metal cation, as a class of Cs 2 BB'Cl 6 double perovskites with remarkable optical properties, including large and tunable exciton binding energies as computed by the GW-Bethe-Salpeter equation (GW-BSE) method. We attribute the unusual electronic structure of these compounds to the mixing of the Alk-Cl and TM-Cl sublattices, leading to materials with small band gaps, large exciton binding energies, and absorption spectra that are strongly influenced by the identity of the transition metal. The role of the double-perovskite structure in enabling these unique properties is probed through an analysis of the electronic structures and chemical bonding of these compounds in comparison with other transition-metal and alkali transition-metal halides.

14 SOLAR ENERGY↗
NASA NTRS2007

Toxicity and Radioprotective Effects of DF-1 and Carbon Nanotubes in Human Lung and Liver Cell Lines

The DF-1 compound, a sixty carbon fullerene derivative, has been shown to have antioxidant effects and is thought to possibly help mediate the effects of radiation on cells. While this is potentially useful, it is important to first understand the effect that the DF-1 has on the cells and the growth rate of the cells to determine if the material itself has any innate toxicity. A growth curve was established for both HF-19 cells, human fibroblasts, and HepG2 cells, liver tissue cells in the presence of two different concentrations of DF-1 and for untreated controls. The cells were plated in triplicate in 60mm dishes and were lifted and counted with a hemocytometer daily for one week. The growth curve data for the HF-19 cells show that while the low concentration of DF-1 had no apparent effect on the growth rate, the high concentration of DF-1 appeared to severely inhibit the growth of the HF-19 cells. The growth curve data for the HepG2 cells shows that the DF-1 compound had no significant effect on the rate at which the cells grew. A second growth curve study was performed plain carbon nanotubes, but with only 24 hour exposure to a high and low concentration of material. The carbon nanotubes are another carbon compound similar to DF-1, but in the shape of a tube, rather than a ball. We hypothesize that nanotubes may also mediate the effect of radiation on cells. This time, nanotubes did not showed any significant effect on the growth rate HF-19 or HepG2 cells. A third growth curve study is underway to further determine the effect of DF-1, nanotubes, and a derivatized nanotube (BHT-nanotubes). This derivatized nanotube has been modified with a compound that is known to be very effective at neutralizing free radicals. We expect that the high concentration of DF-1 and possibly the nanotubes and BHT-nanotubes may inhibit the growth of the HF-19 cells while the low concentration will resemble the growth of the control. We also hypothesize that there will be no significant effect on the growth of the HepG2 cells by the nanotubes, and BHT-nanotubes. In order to examine the usefulness of the DF-1, nanotubes, and BHT-nanotubes in mediating the effects of radiation a clonogenic assay is being performed. The HF-19 cells were plated in different concentrations of the various compounds and exposed to varying amounts of radiation. The cells are being allowed to grow in a small enough concentration so that the ability of each cell to divide can be seen by the development of cell clusters. By comparing the irradiated control to the un-irradiated control the effects of radiation alone can be seen. By comparing the compound treated irradiated cells to the irradiated control the usefulness of each compound can be seen. It is thought that Amifostine, the positive control, will have more regularly dividing cells then the irradiated control, as will DF-1 and hopefully both nanotube materials as well.

Burgoyne, Madeline↗
NASA NTRS2003

Lead-free solders: issues of toxicity, availability and impacts of extraction

This project set out to evaluate the critical issues of toxicity and public health effects, material availability, and the environmental impacts of raw material extraction and metal finishing, with the goal of using environmental impact as a factor in selecting feasible lead-free alloys.

toxicity lead-free solder packaging↗
DOE OSTI2024

January 2023 Semiannual Saltstone Toxicity Characteristic Leaching Procedure (TCLP) Results

The aqueous waste from Tank 50 (salt solution) is sampled semiannually for transfers to the Saltstone Production Facility (SPF). Salt solution is treated at SPF and disposed of in the Saltstone Disposal Facility (SDF). Per request of customer, X-TTR-Z-00027, Revision 0, two SDF waste form (saltstone) samples were prepared in the Savannah River National Laboratory (SRNL) from the Tank 50 Waste Acceptance Criteria (WAC) sample and Z-area premix material for January 2023 semiannual Toxicity Characteristic Leaching Procedure (TCLP) samples. One sample contained a Full Premix which included 10:45:45 (by weight) of cement, slag, and fly ash. The second sample contained 60:40 (by weight) of slag and fly ash only referred to as the “Cement-Free grout sample.” Results from the technical report support Task 2: ‘Grout Leaching Analyses’ of the Task Technical Request (TTR) prepared by Savannah River Mission Completion (SRMC). After at least 28 days cured, a sample of each of the SDF waste forms was collected and shipped to a certified laboratory for analysis using the Toxicity Characteristic Leaching Procedure (TCLP). The January 2023 semiannual saltstone (Full Premix) and the Cement-Free grout samples met the South Carolina (SC) Code of Regulations for Hazardous Waste Management Regulations (HWMR) 61-79.261.24 and 61-79.268.48 requirements for a non-hazardous waste form with respect to the Resource Conservation and Recovery Act (RCRA) metals and Underlying Hazardous Constituents (UHCs), and also met the SPF WAC that was in effect at the time of the tank sampling.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1977

Assessment of relative flammability and thermochemical properties of some thermoplastic materials

Thermomechanical properties, flammability, oxygen index, relative toxicity of pyrolysis effluents, and char yields were studied for 12 advanced polymers which are candidates for use in aircraft interiors as decorative films, compression- and injection-molded parts and thermoplastic parts. Polymers sampled included polyphenylene sulfide, 9,9 bis (4-hydroxyphenol) fluorene polycarbonate-poly (dimethylsiloxane), polyether sulfone, polyvinyl fluoride and polyvinylidene fluoride. Availability of these samples, whether in commercial form or in test quantities, is specified. An estimate of relative fire resistance for the materials was obtained; the five polymers listed above were found to be the most fire resistant of the 12 sampled.

Kourtides, D. A.↗
NASA NTRS1977

Thermochemical characterization of polymers for improved fire safety

Apparatus has been constructed for studying the thermal decomposition of polymers as a function of temperature. Such data is needed to evaluate the toxic threat presented by polymeric materials under fire conditions such as the smoldering fire of the type that occurs in closed areas such as coat closets in which anaerobic decomposition of polymers occurs. The apparatus allows the products of thermal decomposition to be collected and analyzed by infrared spectrometry and mass spectrometry. Data obtained from dog hair, an aromatic polyamide, polyphenylene sulfide, and polybenzimidazole are presented. It was found that significant amounts of toxic gas were evolved from dog hair at temperatures as low as 250 C, while temperatures in excess of 500 C were necessary in order for the evolution of toxic gas from the aromatic polymers to become significant.

Lerner, N. R.↗
NASA NTRS2011

Metal-Matrix/Hollow-Ceramic-Sphere Composites

A family of metal/ceramic composite materials has been developed that are relatively inexpensive, lightweight alternatives to structural materials that are typified by beryllium, aluminum, and graphite/epoxy composites. These metal/ceramic composites were originally intended to replace beryllium (which is toxic and expensive) as a structural material for lightweight mirrors for aerospace applications. These materials also have potential utility in automotive and many other terrestrial applications in which there are requirements for lightweight materials that have high strengths and other tailorable properties as described below. The ceramic component of a material in this family consists of hollow ceramic spheres that have been formulated to be lightweight (0.5 g/cm3) and have high crush strength [40.80 ksi (.276.552 MPa)]. The hollow spheres are coated with a metal to enhance a specific performance . such as shielding against radiation (cosmic rays or x rays) or against electromagnetic interference at radio and lower frequencies, or a material to reduce the coefficient of thermal expansion (CTE) of the final composite material, and/or materials to mitigate any mismatch between the spheres and the matrix metal. Because of the high crush strength of the spheres, the initial composite workpiece can be forged or extruded into a high-strength part. The total time taken in processing from the raw ingredients to a finished part is typically 10 to 14 days depending on machining required.

Baker, Dean M.↗
DOE OSTI2025

High-throughput and data-driven search for stable optoelectronic AMSe 3 materials

The rapid advancement in emerging optoelectronic technologies demands highly efficient, affordable, and ecofriendly materials. In this context, ternary chalcogenides, especially ternary selenides, show early promise as a material class due to their stability and remarkable electronic, optical, and transport properties. In this work, we integrate first-principles-based high-throughput computations with machine learning (ML) techniques to predict the thermodynamic stability and optoelectronic properties of 920 valency-satisfied selenide compounds. Through investigating polymorphism, our study reveals the edge-sharing orthorhombic Pnma phase (NH 4 CdCl 3 -type) as the most stable structure for most ternary selenides. High-fidelity supervised ML models are trained and tested to accelerate stability and band gap predictions. These data-driven models pin down the most influential features that dominantly control key material characteristics. The multistep high-throughput computations identify the ternary selenides with optimal direct band gaps, light carrier masses, and strong optical absorption edges. The extensive materials screening considering phase stability, toxicity, and defect tolerance, finally identifies the seven most suitable candidates for photovoltaic applications. Two of these final compounds, SrZrSe 3 and SrHfSe 3 , have already been synthesized in a single-phase form, with the latter showing an optically suitable band gap, aligning well with our findings. The non-adiabatic molecular dynamics reveal sufficiently long photoexcited charge carrier lifetimes (on the order of nanoseconds) in some of these selected selenide materials, indicating their exciting characteristics. Overall, our study suggests a robust in silico framework that can be extended to screen large datasets of various material classes for identifying promising photoactive candidates.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Hydrogen Peroxide - Material Compatibility Studied by Microcalorimetry

Environmental and toxicity concerns with current hypergolic propellants have led to a renewed interest in propellant grade hydrogen peroxide (HP) for propellant applications. Storability and stability has always been an issue with HP. Contamination or contact of HP with metallic surfaces may cause decomposition, which can result in the evolution of heat and gas leading to increased pressure or thermal hazards. The NASA Johnson Space Center White Sands Test Facility has developed a technique to monitor the decompositions of hydrogen peroxide at temperatures ranging from 25 to 60 C. Using isothermal microcalorimetry we have measured decomposition rates at the picomole/s/g level showing the catalytic effects of materials of construction. In this paper we will present the results of testing with Class 1 and 2 materials in 90 percent hydrogen peroxide.

Homung, Steven D.↗