Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “martensite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Measurement of the Hugoniot and shock-induced phase transition stress in wrought 17-4 PH H1025 stainless steel

Uniaxial strain, reverse-ballistic impact experiments were performed on wrought 17-4 PH H1025 stainless steel, and the resulting Hugoniot was determined to a peak stress of 25 GPa through impedance matching to known standard materials. The measured Hugoniot showed evidence of a solid–solid phase transition, consistent with other martensitic Fe-alloys. The phase transition stress in the wrought 17-4 PH H1025 stainless steel was measured in a uniaxial strain, forward-ballistic impact experiment to be 11.4 GPa. Linear fits to the Hugoniot for both the low and high pressure phase are presented with corresponding uncertainty. The low pressure martensitic phase exhibits a shock velocity that is weakly dependent on the particle velocity, consistent with other martensitic Fe-alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructure and creep strength of simulated intercritical heat-affected zone of grade 91 steel

The intercritical heat affected zone (ICHAZ) has been reported as one of the most Type IV cracking susceptible regions in 9Cr creep-resistant steel weldments. However, creep degradation mechanisms within the ICHAZ itself need further clarifications. In this work, two ICHAZ specimens of Grade 91 steel, low-temperature ICHAZ (LT-ICHAZ) and high-temperature ICHAZ (HT-ICHAZ), were simulated using the Gleeble thermomechanical system by exposing to two peak temperatures (860 °C and 900 °C) between $A_{C1}$ and $A_{C3}$. Dramatically different creep strengths of two simulated ICHAZs were observed and studied. We report dilation curve analysis indicates a high fraction of newly transformed martensite formed in the HT-ICHAZ, which results in a much higher hardness (360 HV0.5) of the HT-ICHAZ than 266 HV0.5 of LT-ICHAZ. Precipitates, especially $M_{23}C_6$ carbides, were not fully dissolved in both ICHAZ specimens. After a typical postweld heat treatment (760 °C-2 hours), the faster recovery of low-carbon martensite and reduced precipitation strengthening due to $M_{23}C_6$ carbides coarsening in the HT-ICHAZ led to a significant hardness reduction. These microstructural degradations in the HT-ICHAZ made its creep lifetime about 36 times shorter than that of the LT-ICHAZ tested at 650 °C. The remaining tempered martensite from base metal in the LT-ICHAZ was the primary contributor to maintain its high creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High Performance Computing to Quantify the Evolution of Microscopic Concentration Gradients During Flash Processing

During the Flash process, the cross section of a plain-carbon or a low-alloy steel is austenitized through rapid heating and transformed on rapid cooling to a predominantly martensite + bainite structure with small amounts of retained austenite. Unlike conventional heat treating, homogeneity is intentionally avoided during Flash processing of steels. The Flash process assembly consists of a pair of rolls that transfer the steel sheets through the heating and cooling stage of the thermal cycle. The initial microstructure of the steel consists of ferrite (body-centered cubic iron) + carbide ((Fe,X)mCn) mixture. The heating rate through the peak temperature is a function of temperature and reaches a peak of about 300-400°C/s and the cooling rate has a maximum value of 3,000-4,000°C/s. The on-heating phase transformations include carbide dissolution, austenite (face-centered cubic iron) nucleation and growth, and diffusion of carbon and other substitutional elements in the steel. The on-cooling phase transformations include formation of martensite (body-centered tetragonal phase containing supersaturated solute) and bainite (ferrite plates with or without fine carbides). In this project, the focus is on Fe-C-Cr steels that are currently Flash processed for armor applications. The modeling effort proposed here will help optimize the Flash thermal cycle for these low alloy steels to achieve the target performance, which is an ongoing effort at SFP Works. A significant feature of Flash processed Fe-C-Cr steels is the presence of scatter in the through-thickness in the sheet. The variability in hardness results from a variability in the bainite + martensite microstructure that is sensitive to the local chemical concentration of C and Cr. Such a chemical inhomogeneity is intentionally obtained in the Flash process. Although such a microstructural gradient is presumably responsible for the exceptional properties of the Flash processed steel, it is very important to quantify the gradients as a function of Flash variabilities in processing parameters and the input microstructure. Understanding the mechanistic pathway that leads to microstructural gradients could be ground-breaking and instrumental for achieving better process control and optimized microstructural state to meet application-specific strength-ductility requirements. Since the final microstructure depends on setting up precise solute concentration gradients through a rapid heating process, and transforming these regions into various phases, it is important to understand how small changes in steel chemistry, input microstructure (carbide size and distribution), and process variables (Flash thermal cycle) will impact the solute concentration gradients.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Elucidating the temperature dependence of TRIP in Q&P steels using synchrotron X-Ray diffraction, constituent phase properties, and strain-based kinetics models

Understanding the deformation-induced martensitic transformation (DIMT) is critical for interpreting the structure-property relationships that govern the performance of transformation-induced plasticity (TRIP) assisted steels. However, modern TRIP-assisted steels often exhibit DIMT kinetics that are not easily captured by existing empirical models based on bulk tensile strain. We address this challenge by combined bulk uniaxial tensile tests and in-situ high energy synchrotron X-ray diffraction, which resolved the phase volume fractions, stress-strain response, and microstructure evolution of each constituent phase. A modification of the Olson-Cohen model is implemented, which describes the martensitic transformation kinetics as a function of the estimated partitioned strain in austenite, rather than the bulk tensile strain. This DIMT kinetic model is used as a framework to clarify the root cause of an insufficiently understood toughness trough reported for TRIP-assisted steels during deformation at elevated temperatures. Here, the importance of the temperature-dependent toughness is discussed, based on the opportunity to modify deformation processes to tailor the DIMT kinetics and mechanical properties during forming and in service.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fatigue Performance of an Improved Creep Strength 10%Cr Steel

The deployment of 9-12% Cr steels for elevated temperature applications up to 650 °C presents a cost-effective alternative to more expensive nickel-based alloys in steam turbine power generation. To enhance creep resistance at this temperature range, a novel ferritic-martensitic steel, designated CPJ7, was developed and fabricated at the National Energy Technology Laboratory. The alloy design aimed to mitigate the transformation of strengthening carbides into deleterious phases that degrade creep performance. Results have demonstrated that CPJ7 exhibits favorable creep and oxidation resistance at 650 °C. However, its fatigue performance remains unexplored. This study builds upon prior research by evaluating the low cycle fatigue behavior of CPJ7 and verifying that modifications beneficial to creep performance were not detrimental to the fatigue performance. The alloy was tested at both 650 °C and ambient temperature under fully reversed bending conditions (R = − 1) and a load ratio of 0.05. Furthermore, the alloy exhibits cyclic softening, a behavior consistent with other 9-10 wt.% Cr steels. Analysis of the microstructure and hysteresis loops further corroborate cyclic softening mechanisms typical of ferritic-martensitic steels. Overall, the fatigue performance of CPJ7 meets or exceeds that of P91 steel, demonstrating its potential for high-temperature structural applications.

9% Cr ferritic-martensitic steel↗
DOE OSTI2023

Caloric Effects Induced by Uniform and Non-uniform Stress in Shape-Memory Materials

A Ginzburg–Landau model is developed that is adequate to describe a square-to-rectangle martensitic transition with associated shape-memory and superelastic properties. Using this model we study caloric effects in the vicinity of the martensitic transition induced by stress and we compare the case of a uniform uniaxial stress and the case of a non-uniform continuous distribution of stresses that produce bending of the material. The former case corresponds to an elastocaloric effect and the latter corresponds to a flexocaloric effect. The aim of the work is to quantitatively compare both cases, which we show must be accomplished in terms of equal amounts of exchanged mechanical work. It is then obtained that the flexocaloric effect is more efficient for low exchanged work but less efficient for large exchanged work.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Enhanced negative thermal expansion of boron-doped Fe 43 Mn 28 Ga 28.97 B 0.03 alloy

Enhanced negative thermal expansion (NTE) properties are achieved by introducing a little amount of boron in the Fe 43 Mn 28 Ga 28.97 B 0.03 alloy. As a result, this alloy shows a giant NTE coefficient of alpha(1) = -79.7 x 10 -6 K -1 in a wide temperature range from 277 K to 136 K. Compared to the NTE characteristics in Fe 43 Mn 28 Ga 29 , the NTE operation temperature window has expanded by 74% with the corresponding coefficient of thermal expansion increased by 57% within the NTE temperature window for the boron-doped Fe 43 Mn 28 Ga28.97B0.03. Additionally, in-situ synchrotron high-energy X-ray diffraction results suggest that by boron substitution, the large unit cell volume change across martensitic transformation and the wide phase transition temperature interval are responsible for the pronounced NTE behavior in Fe 43 Mn 28 Ga 28.97 B 0.03 . Moreover, for the Fe 43 Mn 28 Ga 28.97 B 0.03 NTE material, the compressive strength and strain are significantly improved compared with that of Fe 43 Mn 28 Ga 29 . The present study indicates that Fe 43 Mn 28 Ga 28.97 B 0.03 with enhanced NTE across martensitic transformation may be used for practical application as thermal-expansion compensators.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure and fracture toughness characterization of three 9Cr ODS EUROFER steels with different thermo-mechanical treatments

Ferritic martensitic ODS steels are one of the candidate structural materials for future Gen-IV nuclear fission and fusion reactors. Here, the dependence of fracture toughness on microstructure was investigated by comparing three 9Cr ODS EUROFER steels manufactured through different thermo-mechanical processing routes. Quasi-static fracture toughness testing was performed with sub-sized C(T) specimens and microstructural characterization was carried out using scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy. It was found that at lower test temperatures (-100 – 22 °C), the fracture toughness was primarily controlled by crack initiation at sub-micron particles and by production of secondary cracks during fracture. At higher temperatures (above 100 °C), fracture toughness was predominantly controlled by the matrix ductility and the grain boundary strength with a relatively ductile coarse-grained alloy demonstrating higher fracture toughness compared to high-strength fine-grained alloys. These results and discussion show that variations in thermomechanical treatments can produce significant differences in microstructure and fracture toughness behavior of ferritic martensitic ODS steels.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The impact of nickel concentration and stacking fault energy on deformation mechanisms in high-purity austenitic Fe-Cr-Ni alloys

Understanding how composition affects deformation mechanisms in austenitic stainless steels is essential for developing accurate predictive models of stress-induced failures and stress corrosion cracking. Nickel (Ni), an element classified as a critical element, plays a crucial role in these processes. It is important to examine how Ni concentration influences stacking fault energy (SFE) and, consequently, the deformation mechanisms of austenitic stainless steels. However, in commercial stainless steels, the effects of other alloying elements and impurities can obscure Ni's role, complicating efforts to isolate its impact. Here, in this study, we use two high-purity Fe-Cr-Ni alloys to investigate how Ni concentration and SFE interact to alter deformation mechanisms and induce martensitic transformation. By combining in situ synchrotron X-ray diffraction (XRD) tensile testing and post-mortem electron microscopy with density functional theory simulations, we gain precise insights into these phenomena. We find that the Fe18Cr10Ni (wt%) alloy, with its low SFE, exhibits higher stacking fault probability, deformation-induced martensitic transformation, and a lesser increase in dislocation density with plastic strain. In contrast, the Fe18Cr14Ni (wt%) alloy, with its higher SFE, shows enhanced deformation twinning and greater dislocation density with increasing strain. These findings from high-purity ternary alloys provide valuable insights that can guide the search for alternative elements to replace Ni while achieving similar effects on phase stability and deformation behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In-situ synchrotron X-ray diffraction investigation on deformation behavior of Nb/NiTi composite during pre-straining process

The mechanisms responsible for deformation behavior in Nb/NiTi composite during pre-straining were investigated systematically using in-situ synchrotron X-ray diffraction, transmission electron microscopy and tensile test. It is shown that upon loading, the composite experiences elastic elongation and slight plastic deformation of B19', B2 and β-Nb phases, together with the forward stress-induced martensitic (SIM) transformation from B2 to B19'. Upon unloading, the deformation mechanisms of the composite mainly involve elastic recovery of B19', B2 and β-Nb phases, compression deformation of β-Nb phase and incomplete B19'→B2 reverse SIM transformation. In the tensile loading-unloading procedure, besides the inherent elastic deformation and SIM transformation, the (001) compound twins in B19' martensite can also be conducive to the elastic deformation occurring in B19'-phase of the composite. Therefore, this composite can exhibit a large recoverable strain after unloading owing to the elastic deformation, and the partially reversible and consecutive SIM transformation together with the (001) compound twins.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Limiting Retained Austenite Decomposition in Quenched and Tempered Steels: Influences of Rapid Tempering and Silicon

Tempering reactions are critical to microstructure and property control in martensitic steels. Here, retained austenite decomposition and cementite precipitation are monitored using Mössbauer spectroscopy in 4340 and 300-M steel under conventional and rapid tempering conditions. Tempering times are compared at a constant tempered hardness by increasing tempering temperatures associated with short time conditions to achieve equivalent matrix softening to that of longer tempering times. Time-temperature combinations that provide equivalent tempered hardness generated microstructures with similar dislocation densities and cementite precipitation fractions; these mechanisms are controlled by self-diffusion. However, systematic differences in retained austenite content were observed at a given degree of softening, where shorter tempering times exhibited higher levels of retained austenite compared to more conventional conditions. At low temperatures, the differences in retained austenite preservation between explored time-temperature conditions are attributed to corresponding differences in carbon diffusion distance (in austenite), the controlling diffusional process of retained austenite decomposition. At higher temperatures, retained austenite decomposition exhibits C-curve kinetic behavior in 4340. Thus, reduced thermodynamic driving force for cementite and ferrite formation at higher temperature is believed to play a role in restricting retained austenite decomposition within some short-time, high temperature tempering regimes. The addition of silicon pushes cementite precipitation and retained austenite decomposition to higher temperatures, although retained austenite decomposition is suppressed to a greater extent than cementite precipitation. Potential is illustrated for coupling rapid tempering with silicon alloying to produce appreciably tempered martensite (~490 HV) with relatively less retained austenite decomposition compared to conventional tempering conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermomechanical Processing for Improved Mechanical Properties of HT9 Steels

Thermomechanical processing (TMP) of ferritic–martensitic (FM) steels, such as HT9 (Fe–12Cr–1MoWV) steels, involves normalizing, quenching, and tempering to create a microstructure of fine ferritic/martensitic laths with carbide precipitates. HT9 steels are used in fast reactor core components due to their high-temperature strength and resistance to irradiation damage. However, traditional TMP methods for these steels often result in performance limitations under irradiation, including embrittlement at low temperatures (<~430 °C), insufficient strength and toughness at higher temperatures (>500 °C), and void swelling after high-dose irradiation (>200 dpa). This research aimed to enhance both fracture toughness and strength at high temperatures by creating a quenched and tempered martensitic structure with ultrafine laths and precipitates through rapid quenching and unconventional tempering. Mechanical testing revealed significant variations in strength and fracture toughness depending on the processing route, particularly the tempering conditions. Tailored TMP approaches, combining rapid quenching with limited tempering, elevated strength to levels comparable to nano-oxide strengthened ferritic alloys while preserving fracture toughness. For optimal properties in high-Cr steels for future reactor applications, this study recommends a modified tempering treatment, i.e., post-quench annealing at 500 °C or 600 °C for 1 h, possibly followed by a brief tempering at a slightly higher temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In Situ Synchrotron X-ray Diffraction Investigations of the Nonlinear Deformation Behavior of a Low Modulus β -Type Ti36Nb5Zr Alloy

The low modulus β-type Ti alloys usually have peculiar deformation behaviors due to their low phase stability. However, the study of the underlying mechanisms is challenging since some physical mechanisms are fully reversible after the release of the load. In this paper, the deformation behavior of a low modulus β-type Ti36Nb5Zr alloy was investigated with the aid of in situ synchrotron X-ray diffraction (SXRD) during tensile loading. The evolution of lattice strains and relative integrated diffraction peak intensities of both the β and α” phases were analyzed to determine the characteristics of the potential deformation mechanisms. Upon loading, the α” diffraction spots appeared at specific azimuth angles of the two-dimensional SXRD patterns due to the <110> fiber texture of original β grains and the selection of favorable martensitic variants. The nonlinear deformation behavior originated from a reversible stress-induced martensitic transformation (SIMT). However, the SIMT contributed a little to the large recoverable strain of over 2.0%, which was dominated by the elastic deformation of the β phase. Various deformation mechanisms were activated successively at different applied strains, including elastic deformation, SIMT and plastic deformation. Our investigations provide in-depth understandings of the deformation mechanisms in β-type Ti alloys with low elastic modulus.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure–Property Correlation in a Laser Powder Bed Fusion Processed High-Strength AF-9628 Steel

Laser powder bed fusion additive manufacturing (LPBF-AM) of a low-alloy, high-performance AF-9628 steel results in exceptionally high strength and good ductility. The reasons for such mechanical properties are investigated through detailed microscopy performed at several length scales. Thus, the characterization of melt pool, porosity, grain morphology, phases, and dislocations is performed in the as-printed material. The as-printed material consists of only 0.004 vol% of uniformly distributed porosity, single-phase martensitic laths with an average lath size of ≈2.5 μm, the absence of carbides indicating interstitial trapping of C atom, and high dislocation density in the martensitic laths. Experimental data through microscopy are then fed in analytical models for calculating strengthening contributions from various strengthening mechanisms. Calculated yield strength agrees well with experimentally determined value, and therefore, activation of various strengthening mechanisms is established in as-printed AF-9628.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Overcoming the Damping–Elasticity Paradox via 3D‐Printed NiTiSn Nanocomposite

Abstract Developing high damping alloys (HDAs) with large elastic strain has attracted growing attention due to the increasing demand for energy absorption with overload reliability and reusability. However, damping capacity inherently conflicts with elasticity, because the former requires a liable movement of crystal defects while the latter opposite. To deal with the damping‐elasticity paradox, the advantage of pseudobinary eutectic reaction and rapid cooling of laser powder bed fusion is taken to fabricate a bulk NiTiSn nanocomposite with a two‐level hierarchical structure. The first‐level architecture is composed of martensitic NiTi nanolamellae and reinforced Ti 3 Sn nanolamellae. In addition to lattice strain matching and lamellar boundary strengthening, a novel mechanism of martensite reorientation mediated by reversible stress‐induced detwinning‐twinning is activated to generate large elastic strain. A high density of nanotwins and nanodomains within NiTi nanolamellae constitute the second‐level architecture, which provides pronounced internal friction for high damping capacity. As a result, our NiTiSn nanocomposite exhibits a record‐high integration of damping capacity (tanδ > 0.10) and elastic strain (exceeding 4.5%), as well as superb stability under cyclic overload. This research not only represents a major breakthrough in achieving HDAs with outstanding damping and elastic strain but also offers a novel paradigm for high‐performance functional and structural materials.

Chemistry↗
DOE OSTI2024

Enhancing Mechanical Properties of Carbon–Silicon Steel through Two–Stage Quenching and Partitioning with Bainitic Transformation: Ultimate Tensile Strength of 1875 MPa and Total Elongation of 8.03%

To achieve the desired microstructural properties, the ongoing development and innovation in new structural steels require novel thermal processing. This study aims to improve the mechanical properties of a commercial spring carbon–silicon steel by tailoring its microstructure through a process involving quenching and partitioning (Q&P) followed by bainitic transformation. A two–stage Q&P process is proposed to generate a nanoscale dispersion of stable retained austenite and carbides within the tempered martensite and bainite microstructure. The resulting tensile properties demonstrate a yield strength of 1280 MPa, an ultimate tensile strength of 1875 MPa, and a total elongation of 8.03%. These values surpass those of conventional spring 9254 steel, highlighting the effectiveness of the thermal treatment design. Microstructure analysis reveals the presence of tempered martensite, bainite sheaves, nanoscale carbides, and aggregates of retained austenite. Moreover, the resulting body–centered cubic matrix exhibits minimal lattice tetragonality of ≈1.0051, coupled with stable retained austenite featuring a carbon concentration of ≈3.42 ± 0.5 wt%, resulting in outstanding strength–ductility properties. In conclusion, these findings indicate that the proposed two–stage Q&P process, followed by bainitic transformation, significantly enhances the mechanical properties of carbon–silicon steels, making it a promising candidate for high–performance spring applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Review of Medium-Mn, Low-Density Steels for Transportation Applications

Low-density steels constitute a broad and complex alloy space (Fe–Mn–Al–C) suitable for a variety of applications. In particular, there has been growing interest in duplex (ferrite + austenite) or multiphase (+ martensite, carbides) low-density steels as a lightweight, advanced high-strength steel (AHSS) for vehicle applications, spurred by extensive decarbonization efforts. Medium-Mn (med-Mn) (3 to 12 wt pct) steels with 3.5 to 10 wt pct Al additions have decreased densities, presenting an interesting opportunity for high-specific strength, intrusion-resistant, and energy-absorbing sheet components with reduced alloying contents compared to high-Mn grades like austenitic Fe–Mn–Al–C or twinning-induced plasticity steels. Compared to leaner med-Mn steels, the physical metallurgy of med-Mn, low-density steels (MMLS) is complex and distinguished by increased δ-ferrite fractions and austenite stacking fault energies, decreased martensite start temperatures, and modified phase transformation windows. Mechanical properties of MMLS are comparable to 3rd generation AHSS, attributable to the unique, multiphase microstructures, and the array of strengthening mechanisms that can be accessed. Despite this, challenges and unknowns remain with respect to their industrial implementation, and new processing routes may need to be developed. Here, this review aims to highlight the composition effects, processing methods, microstructural evolution, deformation behavior, and application properties geared toward manufacturing and performance, altogether assessing the potential of MMLS for transportation applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Deformation mechanisms in an additively manufactured dual-phase eutectic high-entropy alloy

Nanostructured metals and alloys often exhibit high strengths but at the expense of reduced ductility. Through harnessing the far-from-equilibrium processing conditions of laser powder-bed fusion (L-PBF) additive manufacturing, we develop a dual-phase nanolamellar structure comprised of FCC/L1 2 and BCC/B2 phases in a Ni 40 Co 20 Fe 10 Cr 10 Al 18 W 2 eutectic high-entropy alloy (EHEA), which exhibits a combination of ultrahigh yield strength (>1.4 GPa) and large tensile ductility (~17%). The deformation mechanisms of the additively manufactured EHEA are studied via in-situ synchrotron X-ray diffraction and high-resolution transmission electron microscopy. The high yield strength mainly results from effective blockage of dislocation motion by the high density of lamellar interfaces. The refined nanolamellar structures and low stacking fault energy (SFE) promote stacking fault (SF)-mediated deformation in FCC/L1 2 nanolamellae. The accumulation of abundant dislocations and SFs at lamellar interfaces can effectively elevate local stresses to promote dislocation multiplication and martensitic transformation in BCC/B2 nanolamellae. The cooperative deformation of the dual phases, assisted by the semi-coherent lamellar interfaces, gives rise to the large ductility of the as-printed EHEA. In addition, here we also demonstrate that post-printing heat treatment allows us to tune the non-equilibrium microstructures and deformation mechanisms. After annealing, the significantly reduced SFE and thicknesses of the FCC nanolamellae facilitate the formation of massive SFs. The dissolution of nano-precipitates in the BCC/B2 nanolamellae reduces spatial confinement and further promotes martensitic transformation to enhance work hardening. Our work provides fundamental insights into the rich variety of deformation mechanisms underlying the exceptional mechanical properties of the additively manufactured dual-phase nanolamellar EHEAs.

36 MATERIALS SCIENCE↗