Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “limit loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

9975 Shipping package component long-term degradation rates

Special nuclear materials are being stored in the K-Area Complex using 3013 containers that are held within Model 9975 shipping packages. The service life for these packages in storage was recently increased from 15 to 20 years, since some of these packages have been stored for nearly 15 years. A strategy is also being developed whereby such storage might be extended beyond 20 years. This strategy is based on recent calculations that support acceptable 9975 package performance for 20 years with internal heat loads up to 19 watts, and identifies a lower heat load limit for which the package components should degrade at half the bounding rate or less, thus doubling the effective storage life for these lower wattage packages. The components of the 9975 package that are sensitive to aging under storage conditions are the fiberboard overpack and the O-ring seals, although some degradation of the lead shield and outer drum are also possible. This report summarizes degradation rates applicable to lower heat load storage conditions. In particular, the O-ring seals should provide leak-tight performance for more than 40 years in packages for which their maximum temperature is ≤135 °F. Similarly, the fiberboard should remain acceptable in performance of its required safety functions for up to 40 years in packages with a maximum fiberboard temperature ≤125 °F.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of Form of Chromium on Spinel Formation

A number of Hanford high level waste (HLW) streams contain sufficiently high concentrations of chromium for it to become the waste loading limiting component in the waste. Chromium has relatively low solubility in borosilicate glasses and leads to the formation of various crystal phases including spinels. The extent of crystal formation must be managed during melter processing to prevent operational issues and potential premature melter failure that can result from excessive accumulation of crystals in the melter. In previous work for the Department of Energy (DOE) Office of River Protection (ORP), high-waste loading glass formulations were developed for representative HLW streams that are high in chromium. Results from those studies suggested that there may be differences in the crystallization behavior between glasses prepared in crucible melts and those prepared in DuraMelter 100 (DM100) joule heated melter runs. Understanding the cause of those differences has the potential to lead to the development of methods to further increase waste loadings for high chromium HLW streams through control of the formation of chromium-bearing crystals. As noted previously, the potential causes include differences in the form of components in the batch, including the form of chromium, as well as redox effects. This report describes the results from work to elucidate the origins of the observed differences and to identify melter feed composition modifications to control the formation of chromium-bearing crystal phases. The work focused on determining the effects of the form of chromium and the concentrations of oxidants in feed batches on spinel crystallization. Also evaluated was the use of potential melter feed additives to influence the redox state of chromium in the melt and its effect on spinel crystallization. As described in the Test Plan for this work, the objectives were accomplished through a combination of crucible-scale tests, small-scale tests with additives to influence redox state, and melter tests. This work builds on previous work performed at the Vitreous State Laboratory (VSL) of The Catholic University of America (CUA) for ORP to increase the waste loadings and processing rates of HLW glass formulations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Simplification of Fatigue Test Requirements for Damage Tolerance of Composite Interstage Launch Vehicle Hardware

The issue of fatigue loading of structures composed of composite materials is considered in a requirements document that is currently in place for manned launch vehicles. By taking into account the short life of these parts, coupled with design considerations, it is demonstrated that the necessary coupon level fatigue data collapse to a static case. Data from a literature review of past studies that examined compressive fatigue loading after impact and data generated from this experimental study are presented to support this finding. Damage growth, in the form of infrared thermography, was difficult to detect due to rapid degradation of compressive properties once damage growth initiated. Unrealistically high fatigue amplitudes were needed to fail 5 of 15 specimens before 10,000 cycles were reached. Since a typical vehicle structure, such as the Ares I interstage, only experiences a few cycles near limit load, it is concluded that static compression after impact (CAI) strength data will suffice for most launch vehicle structures.

Nettles, A. T.↗

Structural Efficiency of Stitched Composite Panels with Stiffener Crippling

The structural efficiency of blade-stiffened stitched specimens is compared to determine their weight saving potential if blades were allowed to buckle at less than or equal to design ultimate load. Analytical and experimental results from four configurations of crippling specimens are presented. Specimen skin and blades were held together with through-the-thickness stitches prior to curing. No mechanical fasteners were used for the assembly. Tests were conducted with and without low-speed impact damage. Failure modes are discussed. Finite element and experimental results agree for the response of the structures. For some specimen configurations, improved structural efficiency can be obtained by allowing stiffeners to buckle at design limit load rather than requiring that buckling not occur prior to design ultimate load. A parametric study is presented herein which describes the possible weight savings with this approach.

Jegley, Dawn C.↗

Linear Quadratic Tracking Design for a Generic Transport Aircraft with Structural Load Constraints

When designing control laws for systems with constraints added to the tracking performance, control allocation methods can be utilized. Control allocations methods are used when there are more command inputs than controlled variables. Constraints that require allocators are such task as; surface saturation limits, structural load limits, drag reduction constraints or actuator failures. Most transport aircraft have many actuated surfaces compared to the three controlled variables (such as angle of attack, roll rate & angle of side slip). To distribute the control effort among the redundant set of actuators a fixed mixer approach can be utilized or online control allocation techniques. The benefit of an online allocator is that constraints can be considered in the design whereas the fixed mixer cannot. However, an online control allocator mixer has a disadvantage of not guaranteeing a surface schedule, which can then produce ill defined loads on the aircraft. The load uncertainty and complexity has prevented some controller designs from using advanced allocation techniques. This paper considers actuator redundancy management for a class of over actuated systems with real-time structural load limits using linear quadratic tracking applied to the generic transport model. A roll maneuver example of an artificial load limit constraint is shown and compared to the same no load limitation maneuver.

Burken, John J.↗

Enhancing Distribution System Resiliency through a Novel Transactive Energy Systems Framework

Restoration of end-use loads during bulk transmission system outages is a key challenge for electric utilities. During those outages, utilities often do not have enough resources to fully restore the end-use loads. Additionally, not all available switching options are feasible due to voltage and load limits. Incentivizing non-utility flexible assets to provide their flexibility during resiliency events is a potential solution to improve resiliency. This paper presents a new transactive energy system framework (TESF) to incentivize distributed energy resources (DERs) to provide reactive power for supporting the self-healing functions of distribution management system (DMS). TESF engages non-utility DERs during resiliency events by incentivizing them through transactive signals computed using marginal cost of producing reactive power and marginal benefit of additional switching operations. TESF calculates additional switching options, which DMS then leverages to identify new optimal switching plans to restore additional loads. Test system consisting of multiple IEEE-13 node distribution feeders is used to demonstrate the performance of the proposed method. For the given system configuration and use-case, TESF results in 24.82 % additional load restoration and one additional switching operation.

Distribution system, reconfiguration, resiliency, ↗

Gasoline-like Fuel Effects on High-load, Boosted HCCI Combustion Employing Negative Valve Overlap Strategy

In recent years a number of studies have demonstrated that boosted operation combined with external EGR is a path forward for expanding the high load limit of homogeneous charge compression ignition (HCCI) operation with the negative valve overlap (NVO) valve strategy. However, the effects of fuel composition with this strategy have not been fully explored. In this study boosted HCCI combustion is investigated in a single-cylinder research engine equipped with direct injection (DI) fueling, cooled external exhaust gas recirculation (EGR), laboratory pressurized intake air, and a fully-variable hydraulic valve actuation (HVA) valve train. Three fuels with significant compositional differences are investigated: regular grade gasoline (RON = 90.2), 30% ethanol-gasoline blend (E30, RON = 100.3), and 24% iso-butanol-gasoline blend (IB24, RON = 96.6). Results include engine loads from 350 to 800 kPa IMEPg for all fuels at three engine speeds 1600, 2000, and 2500 rpm. All operating conditions achieved thermal efficiency (gross indicated efficiency) between 38 and 47%, low NOX emissions ( 0.1 g/kWh), and high combustion efficiency ( 96.5%). Detailed sweeps of intake manifold pressure (atmospheric to 250 kPaa), EGR (0 25% EGR), and injection timing are conducted to identify fuel-specific effects. The major finding of this study is that while significant fuel compositional differences exist, in boosted HCCI operation only minor changes in operational conditions are required to achieve comparable operation for all fuels. In boosted HCCI operation all fuels were able to achieve matched load-speed operation, whereas in conventional SI operation the fuel-specific knock differences resulted in significant differences in the operable load-speed space. Although all fuels were operable in boosted HCCI, the respective air handling requirements are also discussed, including an analysis of the demanded turbocharger efficiency.

efficiency↗

CHANGO: A Software Tool for Boost Stage Guidance of the Space Launch System Exploration Mission 1

The Day of Launch Initiation Load Update (DOLILU) System is the means by which the Space Launch System (SLS) Vehicle trajectory is designed, verified, and uploaded on the Day of Launch (DOL) in order to ensure a safe flight. Launch vehicles are designed to fly down a narrow angle of attack and sideslip angle corridor in order to keep them within structural load limits. The angle of attack and sideslip angle response to the launch vehicle experiences can vary significantly based upon the winds experienced on the DOL. SLS Boost Stage flight employs an open-loop guidance scheme through Solid Rocket Booster (SRB) separation. In the SLS open-loop scheme, the vehicle will fly a prescribed set of attitudes as a function of the change in altitude since launch. This set of reference attitude values and corresponding altitude reference independent values are designed with ground software using winds measured on the DOL with the goal of minimizing angle of attack and sideslip angle, thereby minimizing related ascent integrated vehicle structural loads. The table of Boost Stage attitude commands as a function of altitude gained since launch is called the chi table. A software tool called CHANGO (Chi Angle Optimizer) designs the Boost Stage chi table which is uploaded to the vehicle’s flight computer and used during ascent by the flight software (FSW). The wind and atmospheric conditions are measured prior to launch and pre-processed to become input to the CHANGO software along with a set of parameters developed in advance of the DOL. CHANGO’s target set consists of the heading and altitude rate at SRB separation determined well before launch by the Program to Optimize Simulated Trajectories (POST). CHANGO consists of a simplified three degree-of-freedom (3-DOF) simulation representing the SLS launch configuration. In general, the launch azimuth is strongly correlated with the heading at SRB separation, and the initial pitchover rate is strongly correlated with the altitude rate at SRB separation. CHANGO uses an adaptation of Powell’s method to vary the initial pitchover rate and launch azimuth to solve a 2-dimentional minimization problem. CHANGO’s trajectory simulation is phase-based, with flight events separating the phases. Each flight phase has different attitude alignment logic. CHANGO’s 3-DOF simulation starts when the vehicle’s thrust-to-weight ratio equals one, and ends at a pre-calculated SRB separation time.

Ahmad, Naeem↗

Structural Characterization of the 216-Z-9 Crib Prior to Decontamination and Demolition Using Robot Crawler and High Resolution Photography

The Department of Energy, Richland Operations Office is preparing to conduct a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) removal action for the decontamination and demolition of the above-grade mining structures and equipment at the 216-Z-9 Crib. An investigation of the condition of the mining complex was initiated to determine constraints necessary for safely conducting the removal of the buildings. While crib headspace chemical analysis and nondestructive analysis of the interior of the buildings was completed to address radiological contamination concerns, the primary concern regarding the removal of the above-grade structures located on the crib cover involves determining the loading capacity and structural integrity of the crib cover slab. Additional concerns included headspace gases and radionuclide contamination. Until the structural analysis was completed, loading limits on the crib cover had been restricted. Photographic documentation revealed the loss of protective tiles and acid resistant coating from the underside of the cover raising a question of concrete stability. The investigation relied heavily on the use of high resolution photography with high intensity lighting for photographic documentation of the underside of the crib cover, followed by structural analysis of the documentation by a team of qualified engineers. Deployment of a robot crawler with attached camera and positioning of a fixed camera were integral to this structural characterization effort. Results of the photographic documentation were of sufficient quality to allow for bounding decisions to be made regarding the loading of the crib cover while performing the demolition of the mining structures (glovebox, excavator, bucket) and the associated buildings. The 216-Z-9 Crib, also known as the 216 Z-9 Recuplex CAW (CA column waste) Waste Disposal Cavern, the Z-9 Trench and the Z-9 Crib was constructed as an engineered trench with an open area beneath a concrete slab. The crib is located near the Plutonium Finishing Plant (PFP) facility, at the Hanford Nuclear Reservation in Eastern Washington State. The crib was used as a disposal site for effluent chemical and radiological wastes from the recovery of uranium and plutonium through extraction or RECUPLEX process, a method that recovered uranium and plutonium from liquid and solid wastes and scraps from other PFP processes. During its operating life, from 1955 through 1962, the Z-9 Crib received liquid wastes totaling approximately four million liters, or one million gallons. Analyses of the crib soil in seven locations to a depth of up to two meters (six feet) beneath the crib floor indicated that the plutonium content of the crib soil ranged from 50 to 150 kg (the highest concentration measured was 34.5 g/L of soil). While performing the structural evaluation of the crib cover, additional characterization information was obtained on the radiological and chemical conditions of the crib and structures. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Mechanical Test Frame for Property Evaluations at Cryogenic Temperature

On-board storage of hydrogen fuel has been designated as a limiting factor in the advancement of fuel cell technologies in the automotive industry. The use of cryo-compressed Type III pressure vessels presents one option to overcome this barrier. These multi-material vessels will be expected to perform at high pressure and extreme low temperatures, which creates a complex engineering design challenge. Many materials exhibit highly temperature-dependent properties, which must be considered for the efficient design of cryo-compressed pressure vessels. Complicating this issue, mechanical property data at cryogenic temperatures is sparse. This technical paper provides a description of a test apparatus commissioned specifically to help address this shortcoming. A mechanical test frame was retrofitted with a continuous flow cryostat capable to evaluate various mechanical properties throughout a broad temperature range of 25 °C to -269 °C with a load limit of 10 kN. An investigation of the thermomechanical properties of an epoxy resin was carried out as a demonstration.

Mechanical characterization, cryogenic pressure ve↗

Center of Gravity Quasi-Static Load Estimate Using Random Vibration Responses

The quasi-static load (QSL) is often levied on flight hardware structural designers as a requirement. This requirement is verified either by test or analysis with engineers using different approaches to meet this requirement. A commonly used approach is to consider the rms acceleration Center of Gravity (CG) responses of test articles undergoing random vibration tests. The differences between structural engineers and/or test conductors within the space industry exist on how the data obtained from flight hardware random vibration tests are used to estimate QSLs. In this paper, a method to accurately estimate the CG grms from the acceleration power spectral densities with an appropriate sigma value to estimate peak CG accelerations is discussed. Recommendations are made to ensure that the community follows consistent QSL estimation from random vibration test data. The method of estimating the CG acceleration responses may also be used to response limit if the flight hardware responses exceed flight limit loads with margins.

Kolaini, Ali↗

Design Optimization and Analysis of a Composite Honeycomb Intertank

Intertanks, the structure between tanks of launch vehicles, are prime candidates for weight reduction of rockets. This paper discusses the optimization and detailed analysis of a 96 in (2.44 m) diameter, 77 in (1.85 m) tall intertank. The structure has composite face sheets and an aluminum honeycomb core. The ends taper to a thick built up laminate for a double lap bolted shear joint. It is made in 8 full length panels joined with bonded double lap joints. The nominal load is 4000 lb/in (7 x 10(exp 5) N/m). Optimization is by Genetic Algorithm and minimizes weight by varying C, core thickness, number and orientation of acreage and buildup plies, and the size, number and spacing of bolts. A variety of cases were run with populations up to 2000 and chromosomes as long as 150 bits. Constraints were buckling, face stresses (normal, shear, wrinkling and dimpling, bolt stress, and bolt hole stresses (bearing, net tension, wedge splitting, shear out and tension/shear out). Analysis is by a combination of theoretical solutions and empirical data. After optimization, a series of coupon tests were performed in conjunction with a rigorous analysis involving a variety of finite element models. The analysis and test resulted in several small changes to the optimized design. The intertank has undergone a 250,000 lb (1.1 x 10(exp 6) N) limit load test and been mated with a composite liquid hydrogen tank. The tank/intertank unit is being installed in a test stand where it will see 200 thermal/load cycles. Afterwards the intertank will be demated and loaded in compression to failure.

Finckenor, Jeffrey↗

Common Probe Design Study and Follow-On Activities

The Common Probe Study was funded by the NASA's Planetary Science Division in the Science Mission Directorate in 2018 to investigate the feasibility of a common aeroshell design for atmospheric probe missions at Venus, Jupiter, Saturn, Uranus, and Neptune. The study involved 4 NASA Centers: Ames Research Center, Goddard Space Flight Center, Langley Research Center, and the Jet Propulsion Laboratory. The common aeroshell design that was studied was a 400 kg, 1.5 m diameter, 45-degree sphere cone shape with a high density heatshield material (Heatshield for Extreme Entry Environments Technology, or HEEET) and a parachute system to extract the descent vehicle. This size of aeroshell could accommodate a descent vehicle of 0.75 m diameter, which could encompass both Tier 1 and Tier 2 science instruments at each of the 5 destinations. Study methodology: First, a notional payload of instruments for each destination was defined based on the top priority measurements indicated by the Planetary Science Decadal Survey. Steep and shallow entry flight path angles (EFPA) were defined for each planet based on qualification and operational g-load limits for current, state-of-the-art instruments. Interplanetary trajectories were then identified that bounded the EFPA range.Next, 3-DoF simulations for entry trajectories were run using the entry state vectors from the interplanetary trajectories. Conical ribbon parachutes were sized based on heatshield separation dynamics. Aero-heating correlations were used to generate stagnation point convective and radiative heat flux profiles. High fidelity thermal response models for various TPS materials were used to size stagnation point thicknesses, with margins based on previous studies. Backshell TPS masses were assumed based on scaled heat fluxes from the heatshield and also from previous mission concepts.Based on these analyses, we have found that the common design is applicable for atmospheric probe missions for 4 out of the 5 destinations. Because of the unique gravity well for Jupiter, the entry environments are more severe resulting in heat loads an order of magnitude higher than for the other destinations.The next step is to determine what follow-on activities NASA should engage in. A questionnaire for the atmospheric probe community has been developed, with a focus on what size of aeroshell should be further analyzed (smaller or same diameter), and what incentives would make using such an aeroshell, if assembled and available, desirable to mission proposers.Preliminary results from this questionnaire will be presented.

Hwang, Helen H.↗

Design of a Thermal Energy Storage System for SMR's

A potential deployment strategy for Small Modular Reactors (SMR's) is in hybrid energy systems where the presence of intermittent energy sources (wind and/or solar) subjects the reactor to a time varying electric load (1). Proposed options for accommodating this load have included operating the reactor in a load follow mode, or operating the reactor at or near steady state and bypassing steam around the turbine directly to the condenser (2). Both of these strategies result in lost energy potential. With the large financial investment associated with a nuclear power plant there is strong economic incentive to run the plant at maximum capacity. One method to accomplish this is the installation of Thermal Energy Storage (TES) that can be charged when grid demand is less than 100% plant capacity. The thermal energy can then be recovered, either as a supplement to the power plant during peak demand times, or can be used for other processes (1). Sensible heat thermal energy storage systems have been proposed for solar energy systems (3). This paper describes such a system for SMRs. These results show the feasibility of a TES system alongside a nuclear power plant that can limit load following operations for the reactor. Load following results in a decrease of capacity factor for the plant along with imposing significant stresses to plant equipment. With the implementation of a TES system these stresses can be transferred from the nuclear plant to the TES system. Not only does this equate to a longer overall life of the plant's hardware, but it also will dramatically increase the capacity factor of the system. This increase in capacity factor will lead to an improved economic return over the lifespan of the reactor. Future development in the near term will focus on coupling the TES system to the dynamic response of the reactor and energy conversion system and developing the models necessary to implement the discharge mode. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Toward Environmentally Friendly Lithium Sulfur Batteries: Probing the Role of Electrode Design in MoS 2 -Containing Li–S Batteries with a Green Electrolyte

While lithium sulfur batteries (Li–S) hold promise as future high energy density low cost energy storage systems, barriers to implementation include low sulfur loading, limited cycle life, and the use of toxic electrolyte solvents. A comprehensive study of Li–S cells in the environmentally benign di(propylene glycol) dimethyl ether (DPGDME)-based electrolyte, using as-prepared MoS 2 nanosheets derived from a facile aqueous microwave synthesis as polysulfide trapping agents, is reported herein for the first time. Conventional coated foil electrodes and binder-free electrodes (BFEs) with various structures are systematically generated and tested to correlate electrode design with the resulting electrochemical behavior. Significantly improved Li–S electrochemistry is demonstrated through the synergy of MoS 2 chemistry and binder-free electrode engineering. In the coating configuration, the MoS 2 -containing cell evinced better rate performance and more stable cyclability than the cell without MoS 2 . In comparison with the coating counterparts, the BFE cells exhibited excellent cycle stability and superior rate capability (10-fold capacities and energy density per electrode weight with 20% higher retention rate) despite 2X higher areal sulfur loading. As a result, the BFE cell improvement can be attributed to the synergistic effect of the i) interconnected macroporous structure of CNT interlayers, providing a conductive framework, and ii) the efficient polysulfide trapping by the MoS 2 nanosheets.

25 ENERGY STORAGE↗

Design Optimization and Analysis of a Composite Honeycomb Intertank

Intertanks, the structure between tanks of launch vehicles, are prime candidates for weight reduction of rockets. This paper discusses the optimization and detailed follow up analysis and testing of a 96 in. diameter, 77 in. tall intertank. The structure has composite face sheets with an aluminum honeycomb core. The ends taper to a thick built up laminate for a double lap bolted splice joint interface. It is made in 8 full length panels joined with bonded double lap joints. The nominal load is 4000 lb/in. Optimization is by Genetic Algorithm and minimizes weight by varying core thickness, number and orientation of acreage and buildup plies, and the size, number and spacing of bolts. A variety of design cases were run with populations up to 2000 and chromosomes as long as 150 bits. Constraints were buckling; face stresses (normal, shear, wrinkling and dimpling); bolt stress; and bolt hole stresses (bearing, net tension, wedge splitting, shear out and tension/shear out). Analysis is by a combination of elasticity solutions and empirical data. After optimization, a series of coupon tests were performed in conjunction with a rigorous analysis involving a variety of finite element models. This analysis and testing resulted in several small changes to the optimized design. The equation used for hole bearing strength was found to be inadequate, resulting in thicker ends. The core thickness increased 0.05", and potting compound was added in the taper to strengthen the facesheet bond. The intertank has undergone a 250,000 lb limit load test and been mated with a composite liquid hydrogen tank. The tank/intertank unit is being installed in a test stand where it will see 200 thermal/load cycles. Afterwards the intertank will be demated and loaded in compression to failure.

Finckenor, Jeff↗

Catalyst-Specific Accelerated Stress Tests in Proton Exchange Membrane Low-Temperature Electrolysis for Intermittent Operation

Device-level stress tests are developed that focus on anode catalyst layer degradation and future anticipated operating conditions, including intermittent load and reduced platinum group metal content. Square-wave cycles with an upper load limit of 2.5 A cm -2 are utilized to screen commercial iridium (Ir) materials. Performance losses are primarily due to decreasing kinetics and are accompanied by catalyst migration into the membrane, worsening catalyst/ionomer integration, and weakening of the catalyst/membrane interface. For ruthenium-containing catalysts, the in situ performances are higher but durabilities lower than Ir baselines, and any performance advantage is lost within the test. Increased loss is likely due to the higher dissolution rate; microscopy confirmed greater degrees of ruthenium migration. For Ir metal or mixed oxides, ex situ activity improvements generally did not translate to in situ performance. The durability, however, is significantly lower and the loss rate increased from 3 (oxide) to 9 (metal) μ V cycle -1 . These results are consistent with historical findings in literature, rationalize the continued use of iridium oxide as a baseline catalyst, and demonstrate that traditional catalyst development approaches may not improve device-level durability when focused on low-cost applications. A shift in focus may therefore be more effective at improving catalyst utilization and lessening load requirements.

08 HYDROGEN↗

Evaluation Of Glass Density to Support the Estimation of Fissile Mass Loadings in Sludge Batch 10 Glasses

Per a directive from the Department of Energy Savannah River Operations Office (DOE-SR) in 2008, the fissile mass loading concentration must remain below 897 g/m 3 in each high-level waste (HLW) glass canister produced by the Defense Waste Processing Facility (DWPF). To support Sludge Batch 5 (SB5) processing, the Savannah River National Laboratory (SRNL) developed a technical basis that facilitates the evaluation of fissile mass loading of the glass product. The calculation is based on the iron (Fe) concentration in the glass as determined by measurements from the Slurry Mix Evaporator acceptability analysis as well as the glass density. In April 2022, a subsequent DOE-SR directive increased the fissile mass loading limit to 2500 g/m 3 beginning with Sludge Batch 11. Thus, the 897 g/m 3 limit still applies to Sludge Batch 10 (SB10) processing. For SB5 through initial Sludge Batch 9 (SB9) processing prior to coupled operation with the Salt Waste Processing Facility (SWPF), SRNL provided DWPF a bounding glass density value that was based on a statistical evaluation of density measurements. To eliminate the need for experimental work, a composition-based density model for HLW glasses was developed at SRNL in 2019. The objective of this report is to present the bounding glass density determined with the composition-based density model for SB10 sludge-only (SO) and coupled processing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗