Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “isotherm”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

A model for analysis of the temperature field downstream of a heated jet injected into an isothermal crossflow at an angle of 90 deg

The temperature distribution downstream of a heated jet entering an isothermal crossflow at an angle of 90 deg is predicted using two conduction models with energy sources above the point of injection, in one case a point source and in the second a line source. The models use effective turbulent diffusivities that are determined empirically from previous measurements. Temperatures predicted by the models are compared to experimental results.

Eriksen, V. L.↗
NASA NTRS1972

Isothermal elastohydrodynamic theory for the full range of pressure-viscosity coefficient.

The isothermal, elastohydrodynamic (EHD) solutions in the inlet region of line contacts are extended to cover the full range of pressure-viscosity parameter, G, and the region of extremely heavy loads. The effect of a composite exponential model for the pressure-viscosity dependence on the film thickness is also studied. Results of the film thickness are compared with those based on work by Grubin, Dowson-Higginson, Bell and Kannel, and Herrebrugh. Comparison is also made between the theoretical results with the recently obtained X-ray film thickness measurements.

Cheng, H. S.↗
NASA NTRS1972

Transient-forced convection film boiling on an isothermal flat plate.

Development of a new approach for the solution of transient-forced convection film boiling on an isothermal flat plate using the boundary layer model. The similarity variables are used to convert the governing partial differential equations to ordinary ones. The results of numerical solutions of these ordinary equations indicate that the transient process can be classified as one-dimensional conduction, intermediate, and the steady-state regions. The time required for the one-dimensional conduction and the time necessary to attain a steady-state condition are obtained. The use of local similarity approximations for the intermediate regime facilitates prediction of complete boundary layer growth. Using the ratio of time at any instant to the steady-state time as abscissa, the curves representing the boundary layer growth can be merged into a single mean curve within 5%. Further, the analysis shows that the average rate of heat transfer during transient is 50 to 100% higher than those at steady state. The average rate of vapor convected away is 10 to 15% lower than at steady state while the average rate of accumulation to form the vapor layer is 1 to 14 times larger.

Nagendra, H. R.↗
NASA NTRS1972

Lunar ash flows - Isothermal approximation.

Suggestion of the ash flow mechanism as one of the major processes required to account for some features of lunar soil. First the observational background and the gardening hypothesis are reviewed, and the shortcomings of the gardening hypothesis are shown. Then a general description of the lunar ash flow is given, and a simple mathematical model of the isothermal lunar ash flow is worked out with numerical examples to show the differences between the lunar and the terrestrial ash flow. The important parameters of the ash flow process are isolated and analyzed. It appears that the lunar surface layer in the maria is not a residual mantle rock (regolith) but a series of ash flows due, at least in part, to great meteorite impacts. The possibility of a volcanic contribution is not excluded. Some further analytic research on lunar ash flows is recommended.

Pai, S. I.↗
NASA NTRS1972

Non-isothermal laminar flow of gases through cooled tubes.

Numerical solutions of the laminar-flow equations in differential form are presented for gas flows through cooled tubes. For nearly isothermal flow there is good agreement with available experimental data, as is also found for the case of a large amount of wall cooling. This correspondence along with a check on the satisfaction of the global momentum and energy constraints allowed an appraisal of the effect of wall cooling on flow through tubes. In general, the effect of wall cooling was to decrease the wall friction and the change in pressure along tubes, but the average heat-transfer coefficient did not vary much.

Back, L. H.↗
NASA NTRS1952

Experimental Study of Isothermal Wake-Flow Characteristics of Various Flame-Holder Shapes

An investigation of the isothermal wake-flow characteristics of several flame-holder shapes was carried out in a 4- by 4-inch flow chamber. The effects of flame-holder-shape changes on the characteristics of the Karman vortices and thus on the recirculation zones to which experimenters have related the combustion process were obtained for several flame holders. The results may furnish a basis of correlation, of combustion efficiency and stability for similarly shaped flame holders in combustion studies. Values of the spacing ratio-(ratio of lateral spacing to longitudinal spacing of vortices] obtained for the various shapes approximated the theoretical value of 0.36 given by the Karman stability analysis. Variations in vortex strength of more than 200 percent and in frequency of more than 60 percent were accomplished by varying flame-holder shape. A maximum increase in the recirculation parameter of 56 percent over that for a conventional V-gutter was also obtained. Varying flameholder shape and size enables the designer to select many schedules of variations in vortex strength and frequency- not obtainable by changing size only and may make it possible to approach theoretical maximum vortex strength for any given frequency.

Younger, G. G.↗
NASA NTRS1973

Isothermal and cyclic oxidation at 1000 and 1100 deg C of four nickel-base alloys: NASA-TRW VIA, B-1900, 713C, and 738X

The isothermal and cyclic oxidation resistance of four cast Ni-base gamma + gamma prime alloys, NASA-TRW Via, B-1900, 713C, and 738X, was determined in still air at 1000 and 1100 C. The oxidation process was evaluated by specific sample weight change with time, sample thickness change, X-ray diffraction of the scales, and sample metallography. The behavior is discussed in terms of the Cr, Al, and refractory metal contents of the alloys.

Barrett, C. A.↗
NASA NTRS1974

Comparison of isothermal and cyclic oxidation behavior of twenty-five commercial sheet alloys at 1150 C

The cyclic and isothermal oxidation resistance of 25 high-temperature Ni-, Co-, and Fe-base sheet alloys after 100 hours in air at 1150 C was compared. The alloys were evaluated in terms of their oxidation, scaling, and vaporization rates and their tendency for scale spallation. These values were used to develop an oxidation rating parameter based on effective thickness change, as calculated from a mass balance. The calculated thicknesses generally agreed with the measured values, including grain boundary oxidation, to within a factor of 3. Oxidation behavior was related to composition, particularly Cr and Al content.

Barrett, C. A.↗
NASA NTRS1973

Cyclic and isothermal oxidation behavior on some Ni-Cr alloys

It is shown experimentally that 3 wt.% Si and 3 wt.% Mn additions can substantially improve the oxidation resistance of Ni-20Cr under both isothermal and cyclic conditions at 1100 and 1200 C. This is especially true in cyclic oxidation. In all cases, Si offers a greater improvement than Mn; however, the advantage of Si is substantial only during cyclic oxidation at 1200 C. The Si additions which lead to alloys of improved oxidation resistance suppress the formation of NiO and NiCr2O4 even under the most severe test conditions. The mechanism of improvement afforded by Mn appears to be the formation of MnCr2O4 at the expense of NiO and NiCr2O4.

Lowell, C. E.↗
NASA NTRS1975

Isothermal elastohydrodynamic lubrication of point contacts. 1: Theoretical formulation

The isothermal elastohydrodynamic lubrication (EHL) of a point contact was analyzed numerically by simultaneously solving the elasticity and Reynolds equations. In the elasticity analysis the contact zone was divided into equal rectangular areas, and it was assumed that a uniform pressure was applied over each area. In the numerical analysis of the Reynolds equation, a phi analysis (where phi is equal to the pressure times the film thickness of the 3/2 power) was used to help the relaxation process. The EHL point contact analysis is applicable for the entire range of elliptical parameters and is valid for any combination of rolling and sliding within the contact.

Hamrock, B. J.↗
NASA NTRS1975

Comparison of sonic boom minimization results in real and isothermal atmospheres

The method of Seebass and George (1972, 1974) for minimizing certain features of the pressure signature and yielding the corresponding F function and equivalent area distribution A in an isothermal atmosphere is modified to provide the same capability for a real atmosphere. The appropriate equations of George and Plotkin (1969) describing horizontal advance, ray tube area, and signature propagation are used.

Darden, C. M.↗
NASA NTRS1975

Comparison of isothermal and cyclic oxidation behavior of twenty-five commercial sheet alloys at 1150 C

Twenty-five commercial nickel-, iron-, and cobalt-base sheet alloys incorporating chromium or chromium and aluminum additions for oxidation resistance were tested at 1150 C in air for 100 hr in both isothermal and 1-hr cyclic furnace exposures. The alloys were evaluated by sample specific weight change, by type of scale formed, by amount and type of spall, and by sample thickness change and microstructure.-

Barrett, C. A.↗
NASA NTRS1976

Isothermal elastohydrodynamic lubrication of point contacts. 2: Ellipticity parameter results

A numerical solution of the isothermal elastohydrodynamic problem for point contacts is presented which reproduces all the essential features of experimental observations based upon optical interferometry. In particular, the two side lobes, in which minimum film thickness regions occur, emerge in the theoretical solutions. The influence of the ellipticity parameter on solutions to the point contact problem is explored. The ellipticity parameter k was varied from 1 (a ball on a plate) to 8 (a configuration approaching line contact). It is shown that the minimum film thickness can be related to the well known line contact solutions by a remarkably simple expression involving either k or the effective radius of curvature ratio R sub y/R sub x.

Hamrock, B. J.↗
NASA NTRS1975

Isothermal elastohydrodynamic lubrication of point contacts. II - Ellipticity parameter results

A numerical solution of the isothermal elastohydrodynamic problem for point contacts has been presented which reproduces all the essential features of the previously reported experimental observations based upon optical interferometry. In particular, the two 'side lobes' in which minimum film thickness regions occur are shown to emerge in the theoretical solutions. The influence of the ellipticity parameter upon solutions to the point contact problem has been explored in the present paper. The ellipticity parameter (k) was varied from one (a ball on a plate) to eight (a configuration approaching line contact), and it has been shown that both the central and minimum film thicknesses can be related to the well known line contact solutions by remarkably simple expressions involving either (k) or the effective radius of curvature ratio (Ry/Rx).

Hamrock, B. J.↗
NASA NTRS1975

Isothermal elastohydrodynamic lubrication of point contacts. I - Theoretical formulation

The analysis of an isothermal elastohydrodynamic lubrication (EHL) point contact was evaluated numerically. This required the simultaneous solution of the elasticity and Reynolds equations. In the elasticity analysis the contact zone is divided into equal rectangular areas and it is assumed that a uniform pressure is applied over each element. In the numerical analysis of the Reynolds' equation a phi analysis where phi is equal to the pressure times the film thickness to the 3/2 power is used to help the relaxation process. The EHL point contact analysis is applicable for the entire range of elliptical parameters and is valid for any combination of rolling and sliding within the contact.

Hamrock, B. J.↗
NASA NTRS1976

Diffusive isothermal partitioning in a layered medium with geologic applications

The diffusive isothermal partitioning of solute in a layered two-phase material has been analyzed to help elucidate the phenomenon of solute partitioning in multiphase lunar and terrestrial materials and to estimate the cooling history of samples. After reviewing the physical chemistry of partitioning and the case of an infinite one-dimensional diffusion couple, we solve in analytic form the case of a finite one-dimensional couple. The solution can be used to estimate cooling histories or to interpret laboratory experiments on partitioning. A sample calculation is included.

Hopper, R. W.↗
NASA NTRS1976

Diffraction calculation of occultation light curves in the presence of an isothermal atmosphere

From diffraction theory, light curves are calculated for stellar occultations by a planetary body with an isothermal atmosphere. The character of the resulting curves is determined by the scale height H, the Fresnel zone size l, the surface atmospheric refractivity, and the planetary radius. An exact general solution and two approximations are presented which are valid when H is much greater than l. The importance is assessed of accounting for diffraction effects of the limb when deducing atmospheric parameters from occultation light curves

French, R. G.↗