Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “injection rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Catalytic combustion with steam injection

The effects of steam injection on (1) catalytic combustion performance, and (2) the tendency of residual fuel to burn in the premixing duct upstream of the catalytic reactor were determined. A petroleum residual, no. 2 diesel, and a blend of middle and heavy distillate coal derived fuels were tested. Fuel and steam were injected together into the preheated airflow entering a 12 cm diameter catalytic combustion test section. The inlet air velocity and pressure were constant at 10 m/s and 600 kPa, respectively. Steam flow rates were varied from 24 percent to 52 percent of the air flow rate. The resulting steam air mixture temperatures varied from 630 to 740 K. Combustion temperatures were in the range of 1200 to 1400 K. The steam had little effect on combustion efficiency or emissions. It was concluded that the steam acts as a diluent which has no adverse effect on catalytic combustion performance for no. 2 diesel and coal derived liquid fuels. Tests with the residual fuel showed that upstream burning could be eliminated with steam injection rates greater than 30 percent of the air flow rate, but inlet mixture temperatures were too low to permit stable catalytic combustion of this fuel.

Anderson, D. N.↗
NASA NTRS2012

One-Dimensional, Two-Phase Flow Modeling Toward Interpreting Motor Slag Expulsion Phenomena

Aluminum oxide slag accumulation and expulsion was previously shown to be a player in various solid rocket motor phenomena, including the Space Shuttle's Reusable Solid Rocket Motor (RSRM) pressure perturbation, or "blip," and phantom moment. In the latter case, such un ]commanded side accelerations near the end of burn have also been identified in several other motor systems. However, efforts to estimate the mass expelled during a given event have come up short. Either bulk calculations are performed without enough physics present, or multiphase, multidimensional Computational Fluid Dynamic analyses are performed that give a snapshot in time and space but do not always aid in grasping the general principle. One ]dimensional, two ]phase compressible flow calculations yield an analytical result for nozzle flow under certain assumptions. This can be carried further to relate the bulk motor parameters of pressure, thrust, and mass flow rate under the different exhaust conditions driven by the addition of condensed phase mass flow. An unknown parameter is correlated to airflow testing with water injection where mass flow rates and pressure are known. Comparison is also made to full ]scale static test motor data where thrust and pressure changes are known and similar behavior is shown. The end goal is to be able to include the accumulation and flow of slag in internal ballistics predictions. This will allow better prediction of the tailoff when much slag is ejected and of mass retained versus time, believed to be a contributor to the widely-observed "flight knockdown" parameter.

Kibbey, Timothy P.↗
NASA NTRS1964

Photographic Study of Liquid-Oxygen Boiling and Gas Injection in the Injector of a Chugging Rocket Engine

High-speed motion pictures were taken of conditions in the injector liquid-oxygen cavity of an RL-10 rocket engine during throttled engine operation. Photographs were taken during operation of the engine in the chugging region as the helium gas was injected to stabilize combustion, during operation at rated thrust, and during transition into chugging conditions as the gas injection was discontinued. Results of the investigation indicate that, during chugging rocket operation of the RL-10 engine, a high population of fairly large bubbles formed and collapsed within the liquid-oxygen cavity at the same frequency as the chamber pressure oscillations. When gaseous helium was injected into the liquid-oxygen cavity, a fog rapidly spread over the entire field of view, and the system immediately became stable. The injection of gaseous helium at rated conditions produced a very slight increase in engine performance but not enough to produce a net gain in a typical mission payload with the extra equipment needed. The inherent low-frequency system instability associated with the fuel system at low thrust levels was reduced by injecting either gaseous helium or hydrogen. Complete stabilization was achieved in some cases, and a reduction in the severity of the oscillations in others. This was apparently due to the ·anchoring of the phase change front to the location of the gas injection.

Conrad, E. William↗
NASA NTRS2013

Stratospheric Ozone Response in Experiments G3 and G4 of the Geoengineering Model Intercomparison Project (GeoMIP)

Geoengineering with stratospheric sulfate aerosols has been proposed as a means of temporarily cooling the planet, alleviating some of the side effects of anthropogenic CO2 emissions. However, one of the known side effects of stratospheric injections of sulfate aerosols is a decrease in stratospheric ozone. Here we show results from two general circulation models and two coupled chemistry climate models that have simulated stratospheric sulfate aerosol geoengineering as part of the Geoengineering Model Intercomparison Project (GeoMIP). Changes in photolysis rates and upwelling of ozone-poor air in the tropics reduce stratospheric ozone, suppression of the NOx cycle increases stratospheric ozone, and an increase in available surfaces for heterogeneous chemistry modulates reductions in ozone. On average, the models show a factor 20-40 increase of the sulfate aerosol surface area density (SAD) at 50 hPa in the tropics with respect to unperturbed background conditions and a factor 3-10 increase at mid-high latitudes. The net effect for a tropical injection rate of 5 Tg SO2 per year is a decrease in globally averaged ozone by 1.1-2.1 DU in the years 2040-2050 for three models which include heterogeneous chemistry on the sulfate aerosol surfaces. GISS-E2-R, a fully coupled general circulation model, performed simulations with no heterogeneous chemistry and a smaller aerosol size; it showed a decrease in ozone by 9.7 DU. After the year 2050, suppression of the NOx cycle becomes more important than destruction of ozone by ClOx, causing an increase in total stratospheric ozone. Contribution of ozone changes in this experiment to radiative forcing is 0.23 W m-2 in GISS-E2-R and less than 0.1 W m-2 in the other three models. Polar ozone depletion, due to enhanced formation of both sulfate aerosol SAD and polar stratospheric clouds, results in an average 5 percent increase in calculated surface UV-B.

aerosol↗
NASA NTRS2016

Silicon Chemistry in the Mesosphere and Lower Thermosphere

Silicon is one of the most abundant elements in cosmic dust, and meteoric ablation injects a significant amount of Si into the atmosphere above 80 km. In this study, a new model for silicon chemistry in the mesosphere lower thermosphere is described, based on recent laboratory kinetic studies of Si, SiO,SiO2, and S(exp +). Electronic structure calculations and statistical rate theory are used to show that the likely fate of SiO2 is a two-step hydration to silicic acid (Si(OH)4), which then polymerizes with metal oxides and hydroxides to form meteoric smoke particles. This chemistry is then incorporated into a whole atmosphere chemistry-climate model. The vertical profiles of Si+ and the Si(exp +)Fe(exp +) ratio are shown to be in good agreement with rocket-borne mass spectrometric measurements between 90 and 110 km. Si(exp +) has consistently been observed to be the major meteoric ion around 110 km; this implies that the relative injection rate of Si from meteoric ablation, compared to metals such as Fe and Mg, is significantly larger than expected based on the irrelative chondritic abundances. Finally, the global abundances of SiO and Si(OH)4 show clear evidence of the seasonal meteoric input function, which is much less pronounced in the case of other meteoric species.

Plane, John M. C.↗
NASA NTRS2016

Investigation of Multiphase Flow in a Packed Bed Reactor Under Microgravity Conditions

In this paper we study the two-phase flow phenomena in a packed bed reactor using an integrated experimental and numerical method. The cylindrical bed is filled with uniformly sized spheres. In the experiment water and air are injected into the bed simultaneously. The pressure distribution along the bed will be measured. The numerical simulation is based on a two-phase flow solver which solves the Navier-Stokes equations on Cartesian grids. A novel coupled level set and moment of fluid method is used to construct the interface. A sequential method is used to position spheres in the cylinder. Preliminary experimental results showed that the tested flow rates resulted in pulse flow. The numerical simulation revealed that air bubbles could merge into larger bubbles and also could break up into smaller bubbles to pass through the pores in the bed. Preliminary results showed that flow passed through regions where the porosity is high. Comparison between the experimental and numerical results in terms of pressure distributions at different flow injection rates will be conducted. Comparison of flow phenomena under terrestrial gravity and microgravity will be made.

computational fluid dynamics↗
NASA NTRS1992

Experiments on the enhancement of compressible mixing via streamwise vorticity. I - Optical measurements

The present study was initiated in an attempt to increase the compressible mixing rate of a supersonic jet injected into a co-flowing supersonic stream by adding streamwise vorticity to the injected flow. This flowfield was imaged using the planar laser scattering technique, and mixing rates were derived entirely from captured images. The results of this image analysis indicate that increases in mixing rate of up to 60 percent are possible through the addition of streamwise vorticity. Furthermore, the degree of mixing enhancement appears to be dependent on the amount of swirl added. Analysis of the instantaneous turbulent structure suggests that this increase in mixing is due to a modification of the largest turbulent structures in the mixing layer.

Naughton, J. W.↗
NASA NTRS2011

Reduction of Altitude Diffuser Jet Noise Using Water Injection

A feasibility study on the effects of injecting water into the exhaust plume of an altitude rocket diffuser for the purpose of reducing the far-field acoustic noise has been performed. Water injection design parameters such as axial placement, angle of injection, diameter of injectors, and mass flow rate of water have been systematically varied during the operation of a subscale altitude test facility. The changes in acoustic far-field noise were measured with an array of free-field microphones in order to quantify the effects of the water injection on overall sound pressure level spectra and directivity. The results showed significant reductions in noise levels were possible with optimum conditions corresponding to water injection at or just upstream of the exit plane of the diffuser. Increasing the angle and mass flow rate of water injection also showed improvements in noise reduction. However, a limit on the maximum water flow rate existed as too large of flow rate could result in un-starting the supersonic diffuser.

Allgood, Daniel C.↗
NASA NTRS2014

Reduction of Altitude Diffuser Jet Noise Using Water Injection

A feasibility study on the effects of injecting water into the exhaust plume of an altitude rocket diffuser for the purpose of reducing the far-field acoustic noise has been performed. Water injection design parameters such as axial placement, angle of injection, diameter of injectors, and mass flow rate of water have been systematically varied during the operation of a subscale altitude test facility. The changes in acoustic far-field noise were measured with an array of free-field microphones in order to quantify the effects of the water injection on overall sound pressure level spectra and directivity. The results showed significant reductions in noise levels were possible with optimum conditions corresponding to water injection at or just upstream of the exit plane of the diffuser. Increasing the angle and mass flow rate of water injection also showed improvements in noise reduction. However, a limit on the maximum water flow rate existed as too large of flow rate could result in un-starting the supersonic diffuser.

Allgood, Daniel C.↗
NASA NTRS1991

Polymers And Riblets Reduce Hydrodynamic Skin Friction

Polymers injected into riblet grooves dramatically reduce polymer flow rate required for drag reduction. Polymer solution injected into valleys of grooves through array of holes or slots angled downstream to keep injected streams within grooves. Injection repeated some distance downstream because volumes of grooves finite and polymer becomes depleted as slowly pulled from groove by turbulence. Potentially useful for oil tankers as means of markedly reducing cost of fuel and used extensively on submarines, other ships, and other marine vehicles.

Bushnell, Dennis M.↗
NASA NTRS1994

A constraint on the pair-density ratio (Z+) in an electron-positron pair wind

We derive a constraint on the pair density ratio, z(sub +) = n(sub +)/n(sub p), in an electron-positron pair wind flowing away from the central region of an accretion disk around a compact object under the assumption of a coupling between electrons, positrons, and protons. The minimum rate at which positrons are injected into the annihilation volume is given by the observed annihilation flux per unit volume. This rate is then used to determine a minimum mass loss rate per unit area, M(dot)(sub *) for a given pair density ratio at the base of the streamline. The requirement that M(dot)(sub *) less than M(dot)(sub *)(sub Edd) (the mean Eddington mass loss rate per unit area) then places a lower limit on the pair density ratio, z(sub +,)(sub min). A positron annihilation line was observed in Nova Muscae 1991 by GRANAT/SIGMA. The narrow width and redshift of the line suggest that the pair production and annihilation regions are physically distinct. We hypothesize that an electron-positron pair wind transports the pairs from the production to the annihilation region and calculate z(sub +),(sub min). We then determine constraints on the physical parameters on the pair production region by comparing z(sub +),(sub min) with previous studies of two-temperature and one-temperature accretion disks with electron-positron pairs.

Moscoso, M. D.↗
NASA NTRS1933

Combustion in a High-Speed Compression-Ignition Engine

An investigation conducted to determine the factors which control the combustion in a high-speed compression-ignition engine is presented. Indicator cards were taken with the Farnboro indicator and analyzed according to the tangent method devised by Schweitzer. The analysis show that in a quiescent combustion chamber increasing the time lag of auto-ignition increases the maximum rate of combustion. Increasing the maximum rate of combustion increases the tendency for detonation to occur. The results show that by increasing the air temperature during injection the start of combustion can be forced to take place during injection and so prevent detonation from occurring. It is shown that the rate of fuel injection does not in itself control the rate of combustion.

Rothrock, A M↗
NASA NTRS1971

Erythropoietic radiosensitivity of the rat during altitude acclimatization.

The effect of a sublethal dose (300 R) of X-radiation upon the erythropoietic system of the rat, during 60-day acclimatization to moderate hypoxia (3,800 m altitude), was studied. Past work has shown that hypoxic animals are damaged less by radiation than animals irradiated in a normal environment; therefore, it was postulated that if, after acclimatization to hypoxia the bone marrow oxygen tension returns to sea-level values, these animals should suffer radiation damage equivalent to animals at sea level. The principal parameters followed were the rate of depletion of injected Fe-59 from the plasma of chronically catheterized rats, and its subsequent reappearance in the circulating erythrocytes. After 20 days of acclimatization, both parameters for altitude-irradiated animals returned to the values of animals irradiated at sea level, previously having reflected increased erythropoiesis. In altitude nonirradiated animals the parameters indicated erythropoietic stimulation persisting up to 45 days acclimatization. The protective effect of the hypoxia on the stem cells vanished during acclimatization, presumably as cellular oxygen tension rose.

Gaugl, J. F.↗
NASA NTRS1986

Basaltic fissure eruptions, plume heights, and atmospheric aerosols

Convective plumes that rise above Hawaiian-style fire fountains consist of volcanic gases, aerosols, fine ash, and entrained heated air. Plume theory has been applied to observational estimates of the rate of thermal energy release from large fire fountains. The theoretically predicted heights of maintained plumes agree very well with the heights found from actual observations. Predicted plume heights for both central-vent (point-source) and fissure (line-source) eruptions indicate a stratospheric penetration by plumes that form over vents with very high magma-production rates. Flood basalt fissure eruptions that produce individual lava flows with volumes greater than 100 cu km at very high mass eruption rates are capable of injecting large quantities of sulfate aerosols into the lower stratosphere, with potentially drastic short-term atmospheric consequences, like acid precipitation, darkening of the sky, and climatic cooling.

Stothers, R. B.↗
NASA NTRS1988

Ballistic transport in II-VI semiconductor compounds and alloys

Realistic band structures are used in calculating the group velocity and scattering rates for electrons with injection energies up to 1 eV in ZnTe, CdTe, and the low-effective-mass alloy Hg(0.7)Cd(0.3)Te. Scattering from longitudinal optical phonons, ionized impurities, and alloy disorder have been included in the full band-structure calculation, which automatically includes both intra- and intervalley scattering. Of the II-VI materials considered, at 77 K HgCdTe is superior for low injection energies (up to 0.25 eV) while CdTe is superior at higher injection energies (1 eV) at room temperature. The attainable mean free paths (equal to or greater than 1000 A) and group velocities (equal to or greater than 10 to the 8th cm/s) for both systems are comparable to values found in III-V systems.

Berding, M. A.↗
NASA NTRS1988

Formation of the wave compressional boundary in the earth's foreshock

Using an evolutionary model and allowing for nonuniform proton injection and wave growth rates, the compressional wave boundaries corresponding to IMF inclinations to the solar wind of theta(BV) equal to 45 and 25 deg were located. The compressional boundaries deduced from this model were found to support the results of Greenstadt and Baum (1986) who have concluded that the observed compressional boundaries are incompatible with wave growth at a fixed growth rate, due to the interaction of a uniform beam with the solar wind. The results indicate, however, that the compressional boundaries are quite compatible with nonuniform beams and growth rates which result from the coupled evolution of the energetic protons and the waves with which they interact. It was found that, in the solar wind frame, the dominant wave-particle interaction in the outer foreshock is the damping of inward propagating (toward the shock) left-polarized waves, producing a magnetically quiet region immediately downstream of the foreshock boundary.

Skadron, George↗
NASA NTRS1990

Effects of streamwise vorticity injection on turbulent mixing layer development

This paper investigates the effect of injected strong streamwise vorticity on the structure and development of a plane mixing layer originating from tripped boundary layers. The experiments were conducted in a mixing layer wind tunnel consisting of two separate legs which were driven individually by centrifugal blowers. It was found that, while the vorticity injection increased the growth rate in the near-field, the asymptotic growth rate was reduced by a factor of about two, together with the peak Reynolds stress levels. The result is attributed to the effect of the relatively strong and short wavelength streamwise vorticity in making the spanwise structures more three-dimensional and slowing down their pairing process, thus reducing entrainment, and hence growth.

Bell, James H.↗