SEARCH · Engineering Papers

Results for “impulse noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Reduction of blade-vortex interaction noise using higher harmonic pitch control

An acoustics test using an aeroelastically scaled rotor was conducted to examine the effectiveness of higher harmonic blade pitch control for the reduction of impulsive blade-vortex interaction (BVI) noise. A four-bladed, 110 in. diameter, articulated rotor model was tested in a heavy gas (Freon-12) medium in Langley's Transonic Dynamics Tunnel. Noise and vibration measurements were made for a range of matched flight conditions, where prescribed (open-loop) higher harmonic pitch was superimposed on the normal (baseline) collective and cyclic trim pitch. For the inflow-microphone noise measurements, advantage was taken of the reverberance in the hard walled tunnel by using a sound power determination approach. Initial findings from on-line data processing for three of the test microphones are reported for a 4/rev (4P) collective pitch control for a range of input amplitudes and phases. By comparing these results to corresponding baseline (no control) conditions, significant noise reductions (4 to 5 dB) were found for low-speed descent conditions, where helicopter BVI noise is most intense. For other rotor flight conditions, the overall noise was found to increase. All cases show increased vibration levels.

Brooks, Thomas F.↗

NASA NTRS1990

Reduction of blade-vortex interaction noise through higher harmonic pitch control

Brooks, Thomas F.↗

NASA NTRS1988

Helicopter main-rotor noise: Determination of source contributions using scaled model data

Acoustic data from a test of a 40 percent model MBB BO-105 helicopter main rotor are scaled to equivalent full-scale flyover cases. The test was conducted in the anechoic open test section of the German-Dutch Windtunnel (DNW). The measured data are in the form of acoustic pressure time histories and spectra from two out-of-flow microphones underneath and foward of the model. These are scaled to correspond to measurements made at locations 150 m below the flight path of a full-scale rotor. For the scaled data, a detailed analysis is given for the identification in the data of the noise contributions from different rotor noise sources. Key results include a component breakdown of the noise contributions, in terms of noise criteria calculations of a weighted sound pressure level (dBA) and perceived noise level (PNL), as functions of rotor advance ratio and descent angle. It is shown for the scaled rotor that, during descent, impulsive blade-vortex interaction (BVI) noise is the dominant contributor to the noise. In level flight and mild climb, broadband blade-turbulent wake interaction (BWI) noise is dominant due to the absence of BVI activity. At high climb angles, BWI is reduced and self-noise from blade boundary-layer turbulence becomes the most prominent.

Brooks, Thomas F.↗

NASA NTRS1973

19-20 May 1969, an example of type III emission during the impulsive phase of flares.

Examination of two multiple impulsive events in May 1969, and comparison of their impulsive Ha, hard X-ray, and microwave components with the observed type III emission. No good correlation was observed between meter intensity and the degree of simultaneous Ha outflow, although almost every type III burst had some associated Ha activity. Correspondingly, an inverse relationship existed between X-ray and type III emission - i.e., a strong meter burst accompanied weak X-radiation. This, along with the fact that sufficient energetic electrons were normally present to produce the X rays, implies that the trajectory, rather than electron spectrum or supply, determines whether type III noise is observed during an impulsive event.

Vorpahl, J.↗

NASA NTRS1981

Acoustic noise generation by the DOE/NASA MOD-1 wind turbine

The results of a series of measurements taken over the past year of the acoustic emissions from the DOE/NASA MOD-1 Wind Turbine show the maximum acoustic energy is concentrated in the low frequency range, often below 100 Hz. The temporal as well as the frequency characteristics of the turbine sounds have been shown to be important since the MOD-1 is capable of radiating both coherent and incoherent noise. The coherent sounds are usually impulsive and are manifested in an averaged frequency domain plot as large numbers of discrete energy bands extending from the blade passage frequency to beyond 50 Hz on occasion. It is these impulsive sounds which are identified as the principal source of the annoyance to a dozen families living within 3 km of the turbine. The source of the coherent noise appears to be the rapid, unsteady blade loads encountered as the blade passes through the wake of the tower structure. Annoying levels are occasionally reached at nearby homes due to the interaction of the low frequency, high energy peaks in the acoustic impulses and the structural modes of the homes as well as by direct radiation outdoors. The peak levels of these impulses can be enhanced or subdued through complete propagation.

Kelley, N. D.↗

NASA NTRS1987

The spectral characteristics of rotor blade-vortex interaction noise - Experimental and mathematical results

The BVI impulsive content of a rotor acoustic signal is shown to appear in the mid-frequency range of the power spectrum, between the fifth and thirtieth harmonics of the blade passage frequency, concentrated at the harmonics of the blade passage frequency. These harmonics exhibit a humped or scalloped shape in this mid-frequency spectral region. Increased energy at the harmonics of the shaft frequency appears when the BVI impulsive content demonstrates unsteadiness and blade-to-blade differences in the time domain. A mathematical model of a generalized BVI acoustic signal and its power spectrum shows that the power spectrum is scalloped and filtered by a comb function. The spectrum amplitude is defined by the impulse amplitude and emission time. The scalloping of the spectrum is related to the emission time of the impulse itself, and the spacing of the comb function is related to the repetition time (period) of the impulse. The decay rate of the spectral humps is governed by the inverse of frequency squared. The mathematical model validates the characteristics observed in the data and verify that these characteristics are due to blade-vortex interaction activity.

Martin, Ruth M.↗

NASA NTRS1983

Comparison of broadband noise mechanisms, analyses, and experiments on helicopters, propellers, and wind turbines

Experimental data on broadband noise from airfoils are compared, together with analytical methods, in order to identify the mechanisms of noise emission. Rotor noise is categorized into discrete frequency, impulsive, and broadband components, the last having a continuous spectrum originating from a random source. The results of computer simulations of different rotor blade types which produce broadband noise were compared with experimental data and among themselves in terms of predictions of the spectra obtained. Consideration was given to the overall sound pressure level, unsteady turbulence forces, rotational forces, inflow turbulence, self-generated turbulence, and turbulence in the flow. Data are presented for a helicopter rotor and light aircraft propeller. The most significant source was found to be inflow turbulence induced lift fluctuations in helicopter rotors and boundary layer trailing edge noise on large wind energy conversion systems

George, A. R.↗

DOE OSTI2022

On the determination of shocked surface velocities

Laser Doppler velocimetry is commonly fielded in shock physics experiments to diagnose the times of arrival, magnitudes, and durations of shock impulses as they arrive at shock loaded surfaces. However, in the presence of ejecta, the resulting frequency noise often obscures the surface and subsequent impulses at later times. In this context, we evaluate a dominant wave analysis technique applied to velocimetry data from explosively shocked Sn subjected to a second shockwave, on which ejecta are emitted subsequent to both the first and subsequent shockwave impulses. The analysis reveals surface velocities, the times of arrival of subsequent impulses, and their durations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2024

Notes on Synthetic Aperture Radar Image Quality

Synthetic Aperture Radar (SAR) creates an image of a target scene by coherently processing radar echo returns collected along a flightpath. The quality of the SAR image is inextricably linked to the utility of the image for exploitation supporting the task at hand. Aspects of quality include the fidelity with which it can render the scene being imaged, to include the system’s Impulse Response (IPR) and underlying noise levels/characteristics. Other factors also impact utility.

47 OTHER INSTRUMENTATION↗

NASA NTRS1974

The Vortex Lattice Method for the Rotor-Vortex Interaction Problem

The rotor blade-vortex interaction problem and the resulting impulsive airloads which generate undesirable noise levels are discussed. A numerical lifting surface method to predict unsteady aerodynamic forces induced on a finite aspect ratio rectangular wing by a straight, free vortex placed at an arbitrary angle in a subsonic incompressible free stream is developed first. Using a rigid wake assumption, the wake vortices are assumed to move downsteam with the free steam velocity. Unsteady load distributions are obtained which compare favorably with the results of planar lifting surface theory. The vortex lattice method has been extended to a single bladed rotor operating at high advance ratios and encountering a free vortex from a fixed wing upstream of the rotor. The predicted unsteady load distributions on the model rotor blade are generally in agreement with the experimental results. This method has also been extended to full scale rotor flight cases in which vortex induced loads near the tip of a rotor blade were indicated. In both the model and the full scale rotor blade airload calculations a flat planar wake was assumed which is a good approximation at large advance ratios because the downwash is small in comparison to the free stream at large advance ratios. The large fluctuations in the measured airloads near the tip of the rotor blade on the advance side is predicted closely by the vortex lattice method.

Padakannaya, R.↗

NASA NTRS1984

Two dimensional blade-vortex interaction flow visualization study

Blade-vortex interaction occurs when a rotor blade encounters the tip vortex from a previous rotor blade. To obtain details of the close encounter process, the results from a flow visualization study of an airfoil representing a rotor blade in the wake of an oscillating airfoil serving as a vortex generator are described. A distinguishing feature of this study is that the vortex filament is oriented parallel to the blade span, orthogonal to the test section free stream velocity. This orientation simulates the case of two-dimensional blade-vortex interaction, which is known to produce the most impulsive and most intensive BVI noise. Photographic data are examined to deduce qualitative and quantitative details of the close encounter interaction process with emphasis on structural changes in the vortex filament and its trajectory.

Booth, E. R., Jr.↗

NASA NTRS1992

An IIR median hybrid filter

A new class of nonlinear filters, the so-called class of multidirectional infinite impulse response median hybrid filters, is presented and analyzed. The input signal is processed twice using a linear shift-invariant infinite impulse response filtering module: once with normal causality and a second time with inverted causality. The final output of the MIMH filter is the median of the two-directional outputs and the original input signal. Thus, the MIMH filter is a concatenation of linear filtering and nonlinear filtering (a median filtering module). Because of this unique scheme, the MIMH filter possesses many desirable properties which are both proven and analyzed (including impulse removal, step preservation, and noise suppression). A comparison to other existing median type filters is also provided.

Bauer, Peter H.↗

NASA NTRS1992

Evaluation of a doubly-swept blade tip for rotorcraft noise reduction

A computational study was performed for a doubly-swept rotor blade tip to determine its benefit for high-speed impulsive (HSI) and blade-vortex interaction (BVI) noise. This design consists of aft and forward sweep. For the HSI-noise computations, unsteady Euler calculations were performed for several variations to a rotor blade geometry. A doubly-swept planform was predicted to increase the delocalizing Mach number to 0.94 (representative of a 200+ kt helicopter). For the BVI-noise problem, it had been hypothesized that the doubly-swept blade tip, by producing a leading-edge vortex, would reduce the tip-vortex effect on BVI noise. A procedure was used in which the tip vortex velocity profile computed by a Navier-Stokes solver was used to compute the inflow associated with BVI. This inflow was used by a Euler solver to compute the unsteady pressures for an acoustic analysis. The results of this study were inconclusive due to the difficulty in accurately predicting the viscous tip vortex downstream of the blade. Also, for the condition studied, no leading-edge vortex formed at the tip.

Wake, Brian E.↗

DOE OSTI2022

First demonstration of a fiber optic bolometer on a tokamak plasma (invited)

A fiber optic bolometer (FOB) was demonstrated observing a fusion plasma for the first time at the DIII-D tokamak. A FOB uses a fiber optics-based interferometric technique that is designed to have a high sensitivity to temperature changes [75 mK/(W/m2) responsivity in high vacuum with 0.38 mK noise level] with a negligible susceptibility to electromagnetic interference (EMI) that can be problematic for resistive bolometers in a tokamak environment. A single-channel test apparatus was installed on DIII-D consisting of a measurement FOB and shielded reference FOB. The single-channel FOB showed a negligible increase in the noise level during typical plasma operations (0.39 mK) compared to the benchtop results (0.38 mK), confirming an insignificant EMI impact to the FOB. Comparisons to DIII-D resistive bolometers showed good agreement with the single-channel FOB, indicating that the FOB is comparable to a resistive bolometer when the impulse calibration is applied. The noise-equivalent power density of the calibrated FOB during a plasma operation was 0.55 W/m2 with an average sampling time of 20 ms. The major potential effect of ionizing radiation on the FOB would be the radiation-induced attenuation, which can be efficiently compensated for by adjusting the probing light power.

Lee, S. (ORCID:0000000170289004)↗

NASA NTRS1983

Comparison of several techniques to obtain multiple-look SAR imagery

In order to improve image interpretability when SAR imagery is contaminated by coherent speckle noise, multiple look images are often generated. The performance levels of techniques for the generation of such multiple look imagery are presently assessed, with attention to the detailed impulse responses and signal-to-speckle noise ratios obtainable. The speckle-reduction technique considered are those of the discrete mixed integrator and the image domain filter. It is found that, by using several types of image domain filters, the signal-to-speckle noise ratio can be improved over the conventional discrete mixed integrator method's results while maintaining the equivalent rectangular resolution constant.

Li, F.-K.↗

NASA NTRSDate not supplied

Acoustic Improvements to the 9- by 15-Foot Low Speed Wind Tunnel

A major refurbishment of the 9- by 15-Foot Low Speed Wind Tunnel at NASA Glenn Research Center was undertaken between 2016 and 2019 to improve the acoustic measurement capability of the facility. The principal objective was to lower the background noise in the test section so quiet aircraft propulsors could be tested with good signal-to-noise ratio. The secondary objective was to improve the anechoic quality of the facility so that the measurement uncertainty would be reduced and the data collected would be more accurate. The results of the project were a vastly improved anechoic wind tunnel, with one-third octave sound levels reduced by 8 to 18 dB in the frequency range of interest. The anechoic quality of the test section was improved substantially, reducing the effect of unwanted echoes contaminating the noise measurements, with the error in an impulse response measurement reduced from 0.8 dB to 0.2 dB. This report describes the main acoustic findings and is intended to provide guidance for other facilities requiring a low noise environment

Wind tunnel↗

NASA NTRS1978

A laboratory study of the subjective response to helicopter blade-slap noise

The test stimuli recorded during a recent field study consisted of 16 sounds, each presented at 4 peak noise levels. Two helicopters and a fixed-wing aircraft were used. The impulsive characteristics of one helicopter were varied by operating at different rotor speeds, whereas the other helicopter, the noise of which was dominated by the tail rotor, displayed little variation in blade-slap noise. Thirty-two subjects made noisiness judgments on a continuous, 11 point, numerical scale. Preliminary results indicate that proposed impulsiveness corrections provide no significant improvement in the noisiness predictive ability of Effective Perceived Noise Levels (EPNL). For equal EPNL, the two categories of helicopter stimuli, one of which was far more impulsive than the other, showed no difference in judged noisiness. Examination of the physical characteristics of the sounds presented in the laboratory highlighted the difficulty of reproducing acoustical signals with high-crest factors.

Shepherd, K. P.↗

DOE OSTI2026

Delivery Ring Spill Characterization and Impulse Study

High-intensity particle physics experiments require uniform beam extraction to prevent instantaneous rate spikes from overwhelming detector systems. By analyzing accelerator parameters and extracted beam dynamics, we directly inform spill regulation systems that make real-time adjustments to minimize non-uniformity. This Department of Energy Visiting Faculty Program project transitioned from characterizing Main Injector half-integer slow extraction for SpinQuest to Delivery Ring third-integer slow extraction for Mu2e. Working alongside the Fast Adaptive Neural Control (FANC) group, we developed an automated pipeline that aligns asynchronous instrument channels, embeds quality metrics, and isolates clean spill populations. Analyzing baseline spills alongside a dedicated quadrupole impulse study allowed us to quantify noise structures while mapping time-varying beam response and transit-delay dynamics. These empirical measurements directly ground digital twin models, supporting FANC’s deployment of real-time, FPGA-based neural network controllers in the Mu2e Spill Regulation System.

Dolen, James William [Purdue U., West Lafayette] (↗