Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “improvement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Laser ablation of high-loading Li-ion battery electrodes improves accessible capacity and cycle life for Behind-the-Meter Storage

Adoption of Behind-the-Meter Storage (BTMS) requires design of batteries that enable high safety, long cycle life, and low cost at the system level. Pairing Li 4 Ti 5 O 12 (LTO) with LiMn 2 O 4 (LMO) achieves targets related to safety and cycle life, but these materials' low energy densities contribute to higher cost at the system scale. Increasing electrode loading is a simple approach to improve energy density, but comes with a trade-off in electrode utilization due to long, tortuous Li + diffusion pathways. Here, laser ablation is used to microstructure (pattern) high-loading electrodes to enhance electrode performance through improved Li + diffusion pathways. Four cell types, comprising combinations of standard or patterned anode and cathode, were prepared to evaluate the effects of laser ablation at each electrode. A rate test shows that patterning electrodes enhances active material utilization at ≳1C rates. Patterning the cathode yields the most benefit, as cells with a patterned cathode demonstrate a ~20% higher accessible capacity than those without at 1.4C. Additionally, 1C capacity retention of cells with patterned cathode (91% through 3000 cycles) is significantly improved over cells with only the anode patterned (64%) and non-patterned electrodes (50%). Characterization of post-mortem cells before and after refreshing their electrolyte suggests that 1C capacity retention is improved by mitigation of electrode "dry-out". We hypothesize that the microstructure acts as a reservoir of additional electrolyte, or a path for gas to escape, so that active material remains wetted throughout long-term cycling, and/or the microstructure may reduce localized, gas-forming overpotentials in the high-loading electrode.

25 ENERGY STORAGE↗
DOE OSTI2023

Compositionally complex perovskite oxides: Discovering a new class of solid electrolytes with interface-enabled conductivity improvements

Compositionally complex ceramics (CCCs), including high-entropy ceramics, offer a vast, unexplored compositional space for materials discovery. Herein, we propose and demonstrate strategies for tailoring CCCs via a combination of non-equimolar compositional designs and control of grain boundaries (GBs) and microstructures. Using oxide solid electrolytes for all-solid-state batteries as an example, we have discovered a class of compositionally complex perovskite oxides (CCPOs) with improved lithium ionic conductivities beyond the limit of conventional doping. For example, we demonstrate that the ionic conductivity can be improved by >60% in (Li 0.375 Sr 0.4375 )(Ta 0.375 Nb 0.375 Zr 0.125 Hf 0.125 )O 3-δ compared with the (Li 0.375 Sr 0.4375 )(Ta 0.75 Zr 0.25 )O 3-δ (LSTZ) baseline. Furthermore, the ionic conductivity can be improved by another >70% via quenching, achieving >270% of the LSTZ. Notably, we demonstrate GB-enabled conductivity improvements via both promoting grain growth and altering GB structures through compositional designs and processing. In a broader perspective, this work suggests new routes for discovering and tailoring CCCs for energy storage and many other applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Improvement of two-phase closure models in CTF using Bayesian inference

Under the Consortium for Advanced Simulation of Light Water Reactors (CASL) program, extensive capabilities have been developed in CTF to analyze light-water reactors (LWRs) for normal operating conditions, departure from nucleate boiling (DNB), and system transients. However, further improvements are required in the modeling and simulation of boiling water reactors (BWRs), which is a focus of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. In this work, CTF validation results were used to optimize selected modeling coefficients by calibrating to experimental data using a Bayesian inference approach. Here, calibration studies were conducted to improve (vapor) void fraction prediction without worsening the two-phase pressure drop prediction, as well as to improve the two-phase pressure drop prediction. Calibration was performed for interfacial drag and wall shear models. Surrogates were developed to alleviate the computational expense required for sampling the parameter space using Markov chain Monte Carlo (MCMC). An assessment performed with calibrated models demonstrated an improvement of CTF in its prediction of key parameters such as void fraction and two-phase pressure drop.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Improving the modeling of near-wall interphase heat transfer in porous media models of Pebble Bed Reactors

Here, this work aims to improve capabilities for modeling localized effects in porous media models of Pebble Bed Reactors. The wall-channeling effect is the primary local phenomenon of interest in a PBR, where the presence of the reflector wall disrupts the pebble packing, causing the pebbles near the wall to pack less efficiently and creating large void regions. Accurate modeling of the near-wall region is important as it will affect core bypass flow and temperature predictions. Porous media models are commonly used for design scoping and plant-level simulations of PBRs. Although these models have some capabilities to model the near-wall region, the correlations that are available in porous media codes are often inaccurate when a multi-region model is used to discretize the near-wall region. This work employs a high-to-low analysis to study the accuracy of available interphase heat transfer closures. NekRS, a spectral element computational fluid dynamics code, is used to perform Large Eddy Simulations. These LES simulation results are compared to porous media model results from the Pronghorn porous media code. The friction term of the KTA drag closure is first improved, reducing the error in the prediction of the near-wall velocity from over 50% to less than 5%. This is combined with improvements to the form term from previous works to produce a drag closure that is capable of accurately modeling the wall-channeling effect across a variety of flow conditions. The Nusselt number predictions of several heat transfer correlations are compared to the high-fidelity results where it is found that the KTA heat transfer correlation is capable of accurately predicting the local Nusselt numbers that were determined in the high-fidelity simulation. Comparison of the radial solid temperature profiles, however, reveal discrepancies between NekRS and Pronghorn. It is discovered that the implementation of the interphase heat transfer coefficient that exists in many current porous media codes is not valid when local porosities are modeled. Instead, it is suggested that the interphase heat transfer coefficient should be dependent on the local porosity, the Nusselt number, and the local solid surface-to-volume ratio. Implementation of this change produces improvement in the agreement between the results obtained by NekRS and Pronghorn while using the KTA heat transfer correlation.

interphase heat transfer↗
DOE OSTI2023

Conversion efficiency improvement of ELO GaAs solar cell, deposited on water soluble sacrificial buffer

Here, we demonstrate the improvement of power conversion efficiency of an epitaxially-lifted-off single junction GaAs solar cell deposited on a water-soluble sacrificial buffer architecture by introducing an additional germanium (Ge) interlayer between GaAs and the fluoride buffer. The epitaxial lift-off (ELO) technique has been extensively used to separate III-V device layers from their single crystal GaAs substrates. However, conventional ELO requires the use of concentrated hydrofluoric acid (HF) for extended times to etch out the sacrificial layer, subsequently degrading the surface roughness of the parent wafer. As a result, the wafer has to undergo expensive and intensive chemical mechanical polishing (CMP) processes, costing about 25% of a pristine 6-inch GaAs substrate. In our previous work, we demonstrated a method to eliminating the need for CMP post-processing by using water-assisted ELO (H 2 O-ELO). A water-soluble, 3-layer buffer architecture was developed using alkaline earth compounds. However, devices suffered low performance due to a high defect density in the GaAs active layers. A Ge interlayer was introduced to provide a more favorable surface energy for GaAs growth, which leads to an improvement of GaAs crystal quality. The Ge deposition conditions were optimized to achieve a high-quality Ge layer on triple-layer fluoride buffer. Single junction GaAs devices fabricated on Ge/(Ca,Sr)F 2 /BaF 2 /(Ca,Sr)F 2 showed improvement of solar cell performance parameters featuring increases in V oc by 23.7%, and fill factor (F.F.) by 4.9%, which results in an overall improvement of power conversion efficiency from 10.3% to 12.69%.

14 SOLAR ENERGY↗
DOE OSTI2022

Improving convergence of the Matrix Power Control Algorithm for random vibration testing

Herein, this paper describes modifications to the Matrix Power Control Algorithm (MPCA) to improve convergence for Random Vibration Control (RVC) testing. In particular, this paper presents Multiple-Input Multiple-Output (MIMO) implementations of MPCA in simulation and experiment. An Euler–Bernoulli beam model was simulated with applied base excitations and the Box Assembly with Removable Component (BARC) was used in experiment to validate results. The Bayesian optimization package Dragonfly was used to optimize control parameters. Additionally, a moving-average was employed and optimized to improve the measured response feedback for MPCA, reduce the number of averages needed to be taken between control updates, and further improve convergence. The key results of this paper show that the performance of MPCA can be improved by tuning the control parameters and by applying an optimized moving-average. Furthermore, it is demonstrated that convergence can be achieved within 12 drive-frames, which greatly enhances vibration control capability.

42 ENGINEERING↗
DOE OSTI2022

The Pantheon+ analysis: Improving the redshifts and peculiar velocities of Type Ia supernovae used in cosmological analyses

We examine the redshifts of a comprehensive set of published Type Ia supernovae, and provide a combined, improved catalogue with updated redshifts. We improve on the original catalogues by using the most up-to-date heliocentric redshift data available; ensuring all red shifts have uncertainty estimates; using the exact formulae to convert heliocentric redshifts into the Cosmic Microwave Background (CMB) frame; and utilising an improved peculiar velocity model that calculates local motions in redshift-space and more realistically accounts for the external bulk flow at high-redshifts. We review 2607 supernova redshifts; 2285 are from unique supernovae and 322 are from repeat observations of the same supernova. In total, we updated 990 unique heliocentric redshifts, and found 5 cases of missing or incorrect heliocentric corrections, 44 incorrect or missing supernova coordinates, 230 missing heliocentric or CMB frame redshifts, and 1200 missing redshift uncertainties. The absolute corrections range between 10 -8 ≤ Δz ≤ 0.038, and RMS(Δz) ~ 3 × 10 -3 . The sign of the correction was essentially random, so the mean and median corrections are small: 4 × 10 -4 and 4 × 10 -6 respectively. We examine the impact of these improvements for H 0 and the dark energy equation of state w and find that the cosmological results change by ΔH 0 = -0.12 km s -1 Mpc -1 and Δw = 0.003, both significantly smaller than previously reported uncertainties for H 0 of 1.0 km s -1 Mpc -1 and w of 0.04 respectively.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Biodiesel Ethers: Fatty Acid-Derived Alkyl Ether Fuels as Improved Bioblendstocks for Mixing-Controlled Compression Ignition Engines

In the last 20 years, biodiesel consumption in the United States has swiftly increased to ~2 billion gallons per year as a renewable supplement to fossil fuel. However, further expansion of biodiesel use is currently limited in part by poor cold weather performance, which prevents year-round blending and necessitates blend walls ≤5% v/v. In order to provide a diesel fuel blendstock with improved cold weather performance (cloud point, pour point, and cold filter plug point), while at the same time maintaining other required fuel performance specifications, several biodiesel redox analogues were synthesized and tested. The best performing candidate fuels from this class showed improvement in the derived cetane number (29.3% shorter ignition delay), lower heating value (+4.7 MJ/kg), relative sooting tendency (–7.4 YSI/MJ), and cloud point (15 °C lower) when compared to a B100 biodiesel composed of an identical fatty acid profile. It was observed as a general trend that the reduced form of biodiesel, fatty alkyl ethers (FAEs), shows performance improvements in all fuel property metrics. The suite of improved properties provided by FAEs gives biodiesel producers the opportunity to diversify their portfolio of products derived from lipid and alcohol feedstocks to include long-chain alkyl ethers, a biodiesel alternative with particular applicability for winter weather conditions across the US.

09 BIOMASS FUELS↗
DOE OSTI2020

Minimal Experimental Bias on the Hydrogen Bond Greatly Improves Ab Initio Molecular Dynamics Simulations of Water

Experiment Directed Simulations (EDS) is a method within a class of techniques seeking to improve molecular simulations by minimally biasing the system Hamiltonian to reproduce certain experimental observables. In a previous application of EDS to ab initio molecular dynamics (AIMD) simulation based on electronic density functional theory (DFT), the AIMD simulations of water were biased to reproduce its experimentally derived solvation structure. In particular, by solely biasing the O-O pair correlation functions, other structural and dynamical properties that were not biased were improved. In this work, the hypothesis is tested that directly biasing the OH pair correlation (and hence the H-O∙∙∙H hydrogen bonding), will provide an even better improvement of DFT-based water properties in AIMD simulations. The logic behind this hypothesis is that for most electronic DFT descriptions of water the hydrogen bonding is known to be deficient due to anomalous charge transfer and over polarization in the DFT. Using recent advances to the EDS learning algorithm, we thus train a minimal bias on AIMD water that reproduces the O-H radial distribution function derived from the highly accurate MB-pol model of water. Finally, it is then confirmed that biasing the O-H pair correlation alone can lead to improved AIMD water properties, with structural and dynamical properties in even closer to experiment than the previous EDS-AIMD model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Elucidating Diiodomethane-Induced Improvement in Photonically Cured MAPbI 3 Solar Cells

Diiodomethane (CH 2 I 2 ) has been reported to improve the photonically cured perovskite solar cell (PSC) device performance by reducing pinholes. Here we show that even for pinhole-free methylammonium lead iodide (MAPbI 3 ) made by photonic curing, adding CH 2 I 2 promotes significant performance improvement. We elucidate the mechanisms behind the observed improvement. In addition to current-density versus voltage measurements, we perform a wide variety of characterization to compare the crystallinity, grain structure, optical, chemical, and electrical properties of the photonically cured samples with and without CH 2 I 2 in the MAPbI 3 layer to those of thermally annealed devices. Here, the addition of CH 2 I 2 promotes grain growth in the vertical direction, increases the I/Pb ratio in the final film, and removes the I - ionic diffusion and defect signature associated with iodine interstitials. As a result, we achieve a champion efficiency of 15.04% with MAPbI 3 conversion time of 20 ms, comparable to PSCs that have MAPbI 3 layer thermally annealed for 10 min. Understanding the mechanisms behind additive-induced improvements for non-thermal annealing processes is critical to enabling high-speed PSC manufacturing.

14 SOLAR ENERGY↗
DOE OSTI2025

Ammonolysis Under NH 3 –Limiting Conditions as a Pathway to Improved LaTiO 2 N Water Splitting Photoanodes

LaTiO 2 N is a promising intermediate band gap semiconductor for the water splitting reaction, a pathway to hydrogen fuel from solar energy. However, the photoelectrochemical (PEC) activity of the material is hindered by defects, particularly Ti(III) species, which promote photocarrier recombination. These defects are formed during the high-temperature ammonolysis reaction. Here we show that improved LaTiO 2 N materials can be synthesized under NH 3 -limiting conditions by introducing N 2 to lower the NH 3 partial pressure to0.13atm.This reduces the Ti(III) defect density in the material from 6.06 × 10 16 to ∼4.61 × 10 15 cm −3 , by a factor of 13, based on electron paramagnetic resonance (EPR) spectroscopy. Any remaining Ti(III) defects are localized at the LaTiO 2 N surface, according to X-ray photoelectron spectroscopy (XPS), due to the formation of a depletion layer in the semico. Optical absorption spectra of the improved LaTiO 2 N reveal a blue-shifted band gap absorption edge and a suppressed sub-band gap absorption. Defect removal also reduces a sub-band gap surface photovoltage feature visible in the 1.0 atm reference material. The improved LaTiO 2 N supports a 1.57 mA cm −2 water oxidation photocurrent at 1.23 V RHE under simulated sunlight conditions, and an enhanced quantum efficiency of 4.5% (400 nm) for photocatalytic oxygen evolution from aqueous silver nitrate solution. Stable PEC operation is observed for over 55 min. This confirms that ammonolysis under NH 3 -limiting conditions improves the solar energy conversion properties of LaTiO 2 N. The ability to control metal ion defects in oxynitrides by varying the ammonia partial pressure during ammonolysis might be generally useful for the preparation of metal nitrides and oxynitrides.

defects↗
DOE OSTI2021

Improved Rate for the Oxygen Reduction Reaction in a Sulfuric Acid Electrolyte using a Pt(111) Surface Modified with Melamine

The feasible commercialization of alkaline, phosphoric acid and polymer electrolyte membrane fuel cells depends on the development of oxygen reduction reaction (ORR) electrocatalysts with improved activity, stability, and selectivity. The rational design of surfaces to ensure these improved ORR catalytic requirements relies on the so-called "descriptors" (e.g., the role of covalent and noncovalent interactions on platinum surface active sites for ORR). Here, we demonstrate that through the molecular adsorption of melamine onto the Pt(111) surface [Pt(111)-M ad ], the activity can be improved by a factor of 20 compared to bare Pt(111) for the ORR in a strongly adsorbing sulfuric acid solution. Additionally, the M ad moieties act as "surface-blocking bodies," selectively hindering the adsorption of (bi)sulfate anions (well-known poisoning spectator of the Pt(111) active sites) while the ORR is unhindered. This modified surface is further demonstrated to exhibit improved chemical stability relative to Pt(111) patterned with cyanide species (CN ad ), previously shown by our group to have a similar ORR activity increase compared to bare Pt(111) in a sulfuric acid electrolyte, with Pt(111)-M ad retaining a greater than ninefold higher ORR activity relative to bare Pt(111) after extensive potential cycling as compared to a greater than threefold higher activity retained on a CN ad -covered Pt(111) surface. We suggest that the higher stability of the Pt(111)-M ad interface stems from melamine's ability to form intermolecular hydrogen bonds, which effectively turns the melamine molecules into larger macromolecular entities with multiple anchoring sites and thus more difficult to remove.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Selective Isolation of Surface Grain Boundaries by Oxide Dielectrics Improves Cd(Se,Te) Device Performance

Cd(Se,Te) photovoltaics (PV) are the most widely deployed thin-film solar technology globally, yet continued efficiency improvements are stymied by challenges at the device hole contacts. The inclusion of solution-processed oxide layers such as AlGaO x in the contact stack has yielded improved device open-circuit voltages (V OC ) and fill factors (FF). However, contradictory mechanisms by which these layers improve the device properties have been proposed by the research community. We demonstrate in this work that an underappreciated property of such spin-coated layers is the preferential deposition at grain boundaries, a process that isolates the grain boundaries during contact metallization. The effects of grain-boundary isolation are probed by varying the coverage of solution-processed AlGaO x “barrier” layers on the Cd(Se,Te) surface, quantified by scanning Auger microscopy. Examining coverage-dependent V OC and FF, it was observed that isolating the grain boundaries during metallization is sufficient to prevent damage to the absorber that occurs in devices lacking a barrier layer, while additional coverage contributes to the increased series resistance. Such an effect is agnostic to the material used as a barrier layer, as long as the material does not itself damage the absorber. Spin-coated SiO x was used in place of AlGaO x for an equally beneficial effect. This grain-boundary isolation phenomenon is also observed during Mo deposition and in absorbers that have been contacted with a nitrogen-doped ZnTe layer. The mechanisms by which metallization may degrade the absorber are discussed, as are contact design strategies leveraging barrier layers, which may lead to improved device efficiencies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Improving Gas Selectivity in Membranes Using Polymer-Grafted Silica Nanoparticles

Herein, we demonstrate that tuning of structural parameters and material chemistry enables control of the permeability and selectivity of gases (CO 2 , He, and CH 4 ) in membranes based on poly(butyl methacrylate)-grafted nanoparticles (PGNs). Our data show that the presence of nanoparticles and the overall dense packing of grafted chains noticeable in PGNs with low grafting density have an adverse effect on the diffusivity of gases. This effect is compensated by an improvement in the solubility of CO 2 gas promoted by the silica nanoparticle surface, yielding a substantial improvement in the permeability of CO 2 versus CH 4 . Furthermore, in membranes with high grafting density, changes in the structural arrangements and alterations in the membrane porosity, evident from small-angle X-ray scattering and positron annihilation lifetime spectroscopy, positively influence the permeability of He and CO 2 gases. In contrast, CH 4 permeability in the same membranes is significantly suppressed, suggesting the formation of a unique, highly selective environment for gas separation. As a result, an improvement of up to 50% in selectivity for gas pairs containing large CH 4 molecules is observed. Our studies provide fundamental insights into the role that structural parameters play in gas transport through polymer membranes, laying a foundation for the rational design of membranes with improved permeability and selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Utilizing Machine Learning to Improve Neutralization Potency of an HIV-1 Antibody Targeting the gp41 N-Heptad Repeat

The N-heptad repeat (NHR) of the HIV-1 gp41 prehairpin intermediate (PHI) is an attractive potential vaccine target with high sequence conservation across diverse strains. However, despite the potency of NHR-targeting peptides and clinical efficacy of the NHR-targeting entry inhibitor enfuvirtide, no potently neutralizing NHR-directed monoclonal antibodies (mAbs) nor antisera have been identified or elicited to date. The lack of potent NHR-binding mAbs both dampens enthusiasm for vaccine development efforts at this target and presents a barrier to performing passive immunization experiments with NHR-targeting antibodies. To address this challenge, we previously developed an improved variant of the NHR-directed mAb D5, called D5_AR, which is capable of neutralizing diverse tier-2 viruses. Building on that work, here we present the 2.7Å-crystal structure of D5_AR bound to NHR mimetic peptide IQN17. We then utilize protein language models and supervised machine learning to generate small (n < 100) libraries of D5_AR variants that are subsequently screened for improved neutralization potency. We identify a variant with 5-fold improved neutralization potency, D5_FI, which is the most potent NHR-directed monoclonal antibody characterized to date and exhibits broad neutralization of tier-2 and −3 pseudoviruses as well as replicating R5 and X4 challenge strains. Additionally, our work highlights the ability of protein language models to efficiently identify improved mAb variants from relatively small libraries.

Biopolymers↗
DOE OSTI2023

Salts as Additives: A Route to Improve Performance and Stability of n-Type Organic Electrochemical Transistors

Organic electrochemical transistors (OECTs) are becoming increasingly ubiquitous in various applications at the interface with biological systems. However, their widespread use is hampered by the scarcity of electron-conducting (n-type) backbones and the poor performance and stability of the existing n-OECTs. Here, we introduce organic salts as a solution additive to improve the transduction capability, shelf life, and operational stability of n-OECTs. We demonstrate that the salt-cast devices present a 10-fold increase in transconductance and achieve at least one year-long stability, while the pristine devices degrade within four months of storage. The salt-added films show improved backbone planarity and greater charge delocalization, leading to higher electronic charge carrier mobility. These films show a distinctly porous morphology where the interconnectivity is affected by the salt type, responsible for OECT speed. The salt-based films display limited changes in morphology and show lower water uptake upon electrochemical doping, a possible reason for the improved device cycling stability. Our work provides a new and easy route to improve n-type OECT performance and stability, which can be adapted for other electrochemical devices with n-type films operating at the aqueous electrolyte interface.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hanging drop sample preparation improves sensitivity of spatial proteomics

Spatial proteomics holds great promise for revealing tissue heterogeneity in both physiological and pathological conditions. However, one significant limitation of most spatial proteomics workflows is the requirement of large sample amounts that blurs cell-type-specific or microstructure-specific information. In this study, we developed an improved sample preparation approach for spatial proteomics and integrated it with our previously-established laser capture microdissection (LCM) and microfluidics sample processing platform. Specifically, we developed a hanging drop (HD) method to improve the sample recovery by positioning a nanowell chip upside-down during protein extraction and tryptic digestion steps. Compared with the commonly-used sitting-drop method, the HD method keeps the tissue pixel away from the container surface, and thus improves the accessibility of the extraction/digestion buffer to the tissue sample. The HD method can increase the MS signal by 7 fold, leading to a 66% increase in the number of identified proteins. An average of 721, 1489, and 2521 proteins can be quantitatively profiled from laser-dissected 10 μm-thick mouse liver tissue pixels with areas of 0.0025, 0.01, and 0.04 mm 2 , respectively. The improved system was further validated in the study of cell-type-specific proteomes of mouse uterine tissues.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Protection and enrichment: how two different carbonaceous biofilm supports improve methane yield from encapsulated anaerobic microorganisms

Encapsulating anaerobic microorganisms allows for the separation of the solids retention time from the hydraulic retention time during anaerobic wastewater treatment. The harsh chemistries involved in the process of encapsulation can have adverse effects on microorganisms for anaerobic digestion, especially methanogens, and can lead to lower methane yields after encapsulation. Improving the survival and maintaining activity of anaerobic communities during encapsulation will likely be the key to improving methane yield. In this study, we investigated the encapsulation of biomass grown as biofilms on two carbonaceous materials, biochar and powdered activated carbon (PAC), to improve methane yield. Microorganisms grown as biofilms on biochar and PAC were encapsulated in polyethylene glycol (PEG) and incubated for 10 days. After 10 days, the unamended control capsules produced 81.6 ± 5.4 μmol of methane, while PAC-amended capsules produced 129.8 ± 1.9 μmol and biochar-amended capsules produced 432.96 ± 20.8 μmol methane, with the differences being statistically significant (p < 0.05). In biochar, a higher relative abundance of methanogens led to increased methane production capacity. The ratio of the methyl coenzyme M reductase (mcrA) genes to total 16S rRNA genes in the encapsulated biochar-supported biofilms was significantly higher than that in the encapsulated unsupported (p = 4.9 × 10 −5 ) and the PAC-supported biofilms (p = 0.012). Biochar-supported biofilms also had higher methane output per mcrA or 16S rRNA gene copy number. For the PAC, biofilms were protected from ammonium persulfate (APS), a powerful oxidant used in the encapsulation process. PAC removed 92% of dissolved APS, reducing exposure of the methanogens to this chemical. Unfortunately, this removal of APS compromised capsule stability, limiting the amount of PAC that could be added to the capsules. Furthermore, amendments that improve survival and activity of methanogens should be used in the capsules instead of those that protect methanogens by interfering with encapsulant polymerization chemistry.

Resource recovery↗