Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high current densities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Coupled low-energy - ring current plasma diffusion in the Jovian magnetosphere

The outwardly diffusing Iogenic plasma and the simultaneously inwardly diffusing ring current plasma in the Jovian magnetosphere are described using a coupled diffusion model which incorporates the effects of the pressure gradient of the ring current into the cross-L diffusion coefficient. The coupled diffusion coefficient is derived by calculating the total energy available to drive the diffusion process. The condition is imposed that the diffusion coefficient takes on a local minimum value at some point in the region L = 7-8, at which point the gradient of the Io plasma density is specified as ramp value given by Siscoe et al. (1981). The hypothesis that the pressure gradient of the ring current causes the diminution of radial plasma transport is tested, and solution profiles for the Iogenic and ring current plasma densities are obtained which imply that the Io plasma ramp is caused by a high-density, low-energy component of the ring current hitherto unobserved directly.

Summers, D.↗

Development of moldable, high density reaction bonded silicon nitride

It is noted that currently available reaction bonded silicon nitride (RBSN) materials are limited by relatively low strength (up to 300 MPa) and oxidation resistance, primarily due to open porosity. Attention is given to technology that was developed and used to produce an improved grade of injection molded RBSN having a density of 2.8 g/cc, with significantly decreased open porosity and a strength exceeding 350 MPa. It is shown that these results are primarily due to advances in two areas: silicon powder processing, and nitriding technique. A comparison of room temperature strength and oxidation resistance of the new material with that of state-of-the-art RBSN, showed significant improvements. It is concluded that turbine stator vanes were produced to show that this improved RBSN technology has been reduced to engineering practice.

Mangels, J. A.↗

Technology of Bare Tether Current Collection

The outstanding problem for useful applications of electrodynamic tethers is obtaining sufficient electron current from the ionospheric plasma. Bare tether collectors, in which the conducting tether itself, left uninsulated over kilometers of its length, acts as the collecting anode, promise to attain currents of 10 A or more from reasonably sized systems. Current collection by a bare tether is also relatively insensitive to drops in electron density, which are regularly encountered on each revolution of an orbit. This makes nighttime operation feasible. We show how the bare tether's high efficiency of current collection and ability to adjust to density variations follow from the orbital motion limited collection law of thin cylinders. We consider both upwardly deployed (power generation mode) and downwardly deployed (reboost mode) tethers, and present results that indicate how bare tether systems would perform as their magnetic and plasma environment varies in low earth orbit.

Estes, Robert D.↗

High Density Packaging Technologies for RF Electronics in Small Spacecraft

This paper will describe a few high density packaging technologies which we are currently exploring for use in current and future small spacecraft applications. The three categories of technologies include organic multichip modules (MCMs), ceramic leadless surface mount technology (SMT) and 3D printed waveguide structures. There are many other packaging technologies that currently exist but these three were selected in part due to their long heritage in various commercial, military and space applications along with each having a relatively clear path to flight. For each of these technologies, detailed examples will be included in which hardware has been fabricated and tested for use in RF electronics for spacecraft transponders. The organic MCM example will be described in most detail and it utilizes a packaging technology by the name of CoreEZ which is a trademark of i3 Electronics. This MCM has shrunk a portion of our electronics down to 1/8th of its previous area. The CoreEZ technology has been shown to be rad hard beyond a total ionizing dose (TID) of 300kRad and the MCM which was fabricated has gone through thermal cycling and shown to have no degradation in performance. The ceramic leadless package examples include packages from high reliability manufactures by the name of KCB solutions and Barry Industries. In the case of KCB solutions, we have multiple products that will be described including a hermetic ceramic carrier which houses three microwave monolithic integrated circuits (MMICs) along with small discrete components. Finally, we will discuss the results of our search for a 3D printing process that allows us to reduce the cost and volume of our waveguide filters and diplexers for low cost small satellite applications. We have fabricated a few prototypes using direct metal laser sintering (DMLS) and metal coated plastics. Each of these packaging technology discussions will have a brief overview of its current and future use.

Aquirre, Fernando↗

High Density Packaging Technologies for RF Electronics in Small Spacecraft

This paper will describe a few high density packaging technologies which we are currently exploring for use in current and future small spacecraft applications. The three categories of technologies include organic multichip modules (MCMs), ceramic leadless surface mount technology (SMT) and 3D printed waveguide structures. There are many other packaging technologies that currently exist but these three were selected in part due to their long heritage in various commercial, military and space applications along with each having a relatively clear path to flight. For each of these technologies, detailed examples will be included in which hardware has been fabricated and tested for use in RF electronics for spacecraft transponders. The organic MCM example will be described in most detail and it utilizes a packaging technology by the name of CoreEZ which is a trademark of i3 Electronics. This MCM has shrunk a portion of our electronics down to 1/8th of its previous area. The CoreEZ technology has been shown to be rad hard beyond a total ionizing dose (TID) of 300kRad and the MCM which was fabricated has gone through thermal cycling and shown to have no degradation in performance. The ceramic leadless package examples include packages from high reliability manufactures by the name of KCB solutions and Barry Industries. In the case of KCB solutions, we have multiple products that will be described including a hermetic ceramic carrier which houses three microwave monolithic integrated circuits (MMICs) along with small discrete components. Finally, we will discuss the results of our search for a 3D printing process that allows us to reduce the cost and volume of our waveguide filters and diplexers for low cost small satellite applications. We have fabricated a few prototypes using direct metal laser sintering (DMLS) and metal coated plastics. Each of these packaging technology discussions will have a brief overview of its current and future use.

Schatzel, Donald↗

Ion confinement and transport in a toroidal plasma with externally imposed radial electric fields

Strong electric fields were imposed along the minor radius of the toroidal plasma by biasing it with electrodes maintained at kilovolt potentials. Coherent, low-frequency disturbances characteristic of various magnetohydrodynamic instabilities were absent in the high-density, well-confined regime. High, direct-current radial electric fields with magnitudes up to 135 volts per centimeter penetrated inward to at least one-half the plasma radius. When the electric field pointed radially toward, the ion transport was inward against a strong local density gradient; and the plasma density and confinement time were significantly enhanced. The radial transport along the electric field appeared to be consistent with fluctuation-induced transport. With negative electrode polarity the particle confinement was consistent with a balance of two processes: a radial infusion of ions, in those sectors of the plasma not containing electrodes, that resulted from the radially inward fields; and ion losses to the electrodes, each of the which acted as a sink and drew ions out of the plasma. A simple model of particle confinement was proposed in which the particle confinement time is proportional to the plasma volume. The scaling predicted by this model was consistent with experimental measurements.

Roth, J. R.↗

Constraints on the mass-radius relation for the neutron star in the X-ray burst source 4U/MXB 1820-30 located in the globular cluster NGC 6624

From the spectral evolution of seven X-ray bursts observed from 4U/MXB 1820-30 (Haberl et al., 1986) during the phases of photospheric expansion and cooling, constraints are derived on the mass-radius relation of the neutron star in this system. Taking into account the uncertainty in the source distance and the possible anisotropy of the burst emission. If during bursts with radius expansion the outer layers of the neutron star are of a hydrogen-poor composition, none of the current equations of state of high-density matter is excluded. For a hydrogen-rich composition, only very soft equations of state are allowed.

Van Paradijs, J.↗

The Highly Robust Electrical Interconnects and Ultrasensitive Biosensors Based on Embedded Carbon Nanotube Arrays

We report on our recent breakthroughs in two different applications using well-aligned carbon nanotube (CNT) arrays on Si chips, including (1) a novel processing solution for highly robust electrical interconnects in integrated circuit manufacturing, and (2) the development of ultrasensitive electrochemical DNA sensors. Both of them rely on the invention of a bottom-up fabrication scheme which includes six steps, including: (a) lithographic patterning, (b) depositing bottom conducting contacts, (c) depositing metal catalysts, (d) CNT growth by plasma enhanced chemical vapor deposition (PECVD), (e) dielectric gap-filling, and (f) chemical mechanical polishing (CMP). Such processes produce a stable planarized surface with only the open end of CNTs exposed, whch can be further processed or modified for different applications. By depositing patterned top contacts, the CNT can serve as vertical interconnects between the two conducting layers. This method is fundamentally different fiom current damascene processes and avoids problems associated with etching and filling of high aspect ratio holes at nanoscales. In addition, multiwalled CNTs (MWCNTs) are highly robust and can carry a current density of 10(exp 9) A/square centimeters without degradation. It has great potential to help extending the current Si technology. The embedded MWCNT array without the top contact layer can be also used as a nanoelectrode array in electrochemical biosensors. The cell time-constant and sensitivity can be dramatically improved. By functionalizing the tube ends with specific oligonucleotide probes, specific DNA targets can be detected with electrochemical methods down to subattomoles.

Li, Jun↗

Urban Air Mobility (UAM) Market Study

The Booz Allen Team explored market size and potential barriers to Urban Air Mobility (UAM) by focusing on three potential markets – Airport Shuttle, Air Taxi, and Air Ambulance. We found that the Airport Shuttle and Air Taxi markets are viable, with a significant total available market value in the U.S. of $500 billion, for a fully unconstrained scenario. In this unconstrained best-case scenario, passengers would have the ability to access and fly a UAM at any time, from any location to any destination, without being hindered by constraints such as weather, infrastructure, or traffic volume. Significant legal and regulatory, weather, certification, public perception, and infrastructure constraints exist, which reduce the market potential for these applications to only about 0.5% of the total available market, or $2.5 billion, in the near term. However, we determined that these constraints can be addressed through ongoing intra-governmental partnerships, government and industry collaboration, strong industry commitment, and existing legal and regulatory enablers. We found that the Air Ambulance market is not a viable market if served by electric vertical takeoff and landing (eVTOL) vehicles due to technology constraints but may potentially be viable if a hybrid VTOL aircraft are utilized. The barriers and challenges we characterized in this study can be stratified according to their applicability or potential mitigation through technology as well as market maturity (Figure 1). In the near term, high cost of service will be a key economic challenge. We found potential for significant reduction in service cost through increased vehicle and component efficiency, and automation in a more mature market scenario. Weather conditions also pose a challenge to the UAM market, though there is potential for mitigation of some of these impacts through technology such as sensors enabling operations in low visibility. However, even in a mature market with advanced technology, disruptions are still likely to occur due to weather events such as thunderstorms and strong winds. High density operations will likely stress the current Air Traffic Management (ATM) system in the near term, but technology and new initiatives such as the Air Traffic Management -eXploration project (ATM-X) will enable safe and efficient integration of UAM into the National Airspace System (NAS). Current battery technology creates a barrier in the near term, especially for the Air Ambulance market, as battery weight and extensive recharging times would be needed for these operations. Advancements in battery technology, as well as use of hybrid VTOLs, could significantly reduce this barrier in the longer term. As UAM emerges as a viable mode of transportation in the near term, adverse energy and environmental impacts, particularly noise, may impact community acceptance and potentially persist as the market matures into larger-scale operations. For non-technology related challenges, we found that infrastructure constraints will create a significant barrier to UAM in the near term but could be addressed in the longer term through development and expansion of vertiports. Competition from existing modes of transportation such as ride-sharing (e.g., Lyft, Uber) and ground taxi’s pose a key barrier to UAM in the short term, which will likely evolve into competition from other emerging technologies such as autonomous cars and electric trains in the longer term. Weather events will influence other components of the operation such as passenger comfort (e.g., extreme temperatures, turbulence) and infrastructure (e.g., winter weather causing cracks and degradation in vertiports). There is also potential for these impacts to be heightened in the longer term from the increased frequency of adverse weather such as thunderstorms due to changing climatic conditions. We also found that the public has strong concerns about safety as a passenger in a piloted UAM, including “lasing” of pilots, unruly passengers, and sabotage. They would prefer that all passengers pass through a security screening process before boarding a vehicle. They would also prefer to use UAM for longer regional trips, such as flying from Washington, DC to Baltimore, MD or San Diego, CA to Los Angeles, CA. A longer term automated UAM vehicle market will face challenges due to public apprehension about automation and unmanned operations, and a preference to fly with passengers they know in an autonomous (unmanned) operational scenario.

Rohit Goyal↗

Proton Exchange Membrane (PEM) Fuel Cells for Space Applications

This presentation will provide a summary of the PEM fuel cell development at the National Aeronautics and Space Administration, Johnson Space Center (NASA, JSC) in support of future space applications. Fuel cells have been used for space power generation due to their high energy storage density for multi-day missions. The Shuttle currently utilizes the alkaline fuel cell technology, which has highly safe and reliable performance. However, the alkaline technology has a limited life due to the corrosion inherent to the alkaline technology. PEM fuel cells are under development by industry for transportation, residential and commercial stationary power applications. NASA is trying to incorporate some of this stack technology development in the PEM fuel cells for space. NASA has some unique design and performance parameters which make developing a PEM fuel cell system more challenging. Space fuel cell applications utilize oxygen, rather than air, which yields better performance but increases the hazard level. To reduce the quantity of reactants that need to be flown in space, NASA also utilizes water separation and reactant recirculation. Due to the hazards of utilizing active components for recirculation and water separation, NASA is trying to develop passive recirculation and water separation methods. However, the ability to develop recirculation components and water separators that are gravity-independent and successfully operate over the full range of power levels is one of the greatest challenges to developing a safe and reliable PEM fuel cell system. PEM stack, accessory component, and system tests that have been performed for space power applications will be discussed.

Bradley, Karla↗

Core Losses in Co-Rich Inductors with Tunable Permeability

High frequency, low loss power systems enable electrified aircraft propulsion. Filter inductors that reduce noise in high current systems can account for 50% of the motor drive mass. Efficient inductor cores with tunable permeability reduce system mass by producing less heat, that removes heat sink mass. Requirements for filter inductors vary based on the chosen topology, but all inductor cores must operate below saturation levels. As the saturation flux density is limited (less than ~2 T), high differential current applications require cores with low relative permeabilities. The large induced anisotropies possible in Co-rich metal amorphous nanocomposite materials enables gapless inductors with relative permeabilities down to ~20. These materials have fine grain size ~8nm with a faulted, close packed structure. The impact of different processing methods on core losses are presented along with comparison to other low permeability soft magnetic materials.

Leary, Alex↗

Helium /3/ rich solar flares

Several aspects of a solar flare model that emphasizes evidence for the formation of current filaments as mechanisms of field dissipation are discussed. The origin of flare magnetic fields is considered, along with the thermal distribution, electron density, and high-energy X ray emission of flares. It is suggested that the extreme He-3 enrichment in some solar flares is due to spallation and the subsequent confinement of spallation products in a high-temperature high-density plasma associated with the magnetic instability that produces the flare. A current filament is assumed to produce the spallation and maintain the temperature that yields the high-energy X-ray spectrum and depletes the isotopes D, Li, Be, and B, as observed.

Colgate, S. A.↗

Implementation and Initial Validation of a 100-Kilowatt Class Nested-Channel Hall Thruster

The X3 is a 100-kilowatt class nested-channel Hall thruster developed by the Plasmadynamics and Electric Propulsion Laboratory at the University of Michigan in collaboration with the Air Force Research Laboratory and NASA. The cathode, magnetic circuit, boron nitride channel rings, and anodes all required specific design considerations during thruster development, and thermal modeling was used to properly account for thermal growth in material selection and component design. A number of facility upgrades were required at the University of Michigan to facilitate operation of the X3. These upgrades included a re-worked propellant feed system, a completely redesigned power and telemetry break-out box, and numerous updates to thruster handling equipment. The X3 was tested on xenon propellant at two current densities, 37% and 73% of the nominal design value. It was operated to a maximum steady-state discharge power of 60.8 kilowatts. The tests presented here served as an initial validation of thruster operation. Thruster behavior was monitored with telemetry, photography and high-speed current probes. The photography showed a uniform plume throughout testing. At constant current density, reductions in mass flow rate of 18% and 26% were observed in the three-channel operating configuration as compared to the superposition of each channel running individually. The high-speed current probes showed that the thruster was stable at all operating points and that the channels influence each other when more than one is operating simultaneously. Additionally, the ratio of peak-to-peak AC-coupled discharge current oscillations to mean discharge current did not exceed 51% for any operating points reported here, and did not exceed 17% at the higher current density.

High Power↗

High Temperature Polymers for use in Fuel Cells

NASA Glenn Research Center (GRC) is currently working on polymers for fuel cell and lithium battery applications. The desire for more efficient, higher power density, and a lower environmental impact power sources has led to interest in proton exchanges membrane fuels cells (PEMFC) and lithium batteries. A PEMFC has many advantages as a power source. The fuel cell uses oxygen and hydrogen as reactants. The resulting products are electricity, heat, and water. The PEMFC consists of electrodes with a catalyst, and an electrolyte. The electrolyte is an ion-conducting polymer that transports protons from the anode to the cathode. Typically, a PEMFC is operated at a temperature of about 80 C. There is intense interest in developing a fuel cell membrane that can operate at higher temperatures in the range of 80 C- 120 C. Operating the he1 cell at higher temperatures increases the kinetics of the fuel cell reaction as well as decreasing the susceptibility of the catalyst to be poisoned by impurities. Currently, Nafion made by Dupont is the most widely used polymer membrane in PEMFC. Nafion does not function well above 80 C due to a significant decrease in the conductivity of the membrane from a loss of hydration. In addition to the loss of conductivity at high temperatures, the long term stability and relatively high cost of Nafion have stimulated many researches to find a substitute for Nafion. Lithium ion batteries are popular for use in portable electronic devices, such as laptop computers and mobile phones. The high power density of lithium batteries makes them ideal for the high power demand of today s advanced electronics. NASA is developing a solid polymer electrolyte that can be used for lithium batteries. Solid polymer electrolytes have many advantages over the current gel or liquid based systems that are used currently. Among these advantages are the potential for increased power density and design flexibility. Automobiles, computers, and cell phones require highly efficient power density for lowering emissions and meeting increasing consumer demands. Many of the solutions can be provided by proton exchange membrane fuel cells and lithium batteries. NASA Glenn Research Center has recognized this need, and is presently engaged in a solution. The goals for the summer include mastering synthesis techniques, understanding the reactions occurring during the synthesis, and characterizing the resulting polymer membranes using NMR, DSC, and TGA for the PEMFC and lithium batteries.

Peplowski, Katherine M.↗

How Ionospheric Ions Populate the Magnetosphere during a Magnetic Storm

Ionospheric oxygen ions have been observed throughout the magnetosphere, from the plasma sheet to the ring current region. I t has been found that the O+ /H+ density ratio in the magnetosphere increases with geomagnetic activity and varies with storm phases. During the magnetic storm in late September to earIy October 2002, Cluster was orbiting in the plasma sheet and ring current regions. At prestorm time, Cluster observed high H+ density and low O+ density in the plasma sheet and lobes. During the storm main phase, 0+ density has increased by 10 times over the pre-storm level. Strong field-aligned beams of O+ were observed in the lobes. O+ fluxes were significantly reduced in the central plasma sheet during the storm recovery. However, 0+ was still evident on the boundaries of the plasma sheet and in the lobes. In order to interpret the Cluster observations and to understand how O+ ions populate the magnetosphere during a magnetic storm, we model the storm in early October 2002 using our global ion kinetic simulation (GIK). We use the LFN global simulation model to produce electric and magnetic fields in the outer magnetosphere, the Strangeway outflow scaling with Delcourt ion trajectories to include ionospheric outflows, and the Fok inner magnetospheric model for the plasmaspheric and ring current response to all particle populations. We find that the observed composition features are qualitatively reproduced by the simulations, with some quantitative differences that point to future improvements in the models.

Fok, Mei-Ching↗