Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “heat transfer coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Cooling of Electric Motors Used for Propulsion on SCEPTOR

Benefits of Electric Power: Reduced energy consumption, Lower emissions, Less noise. Traction motors: Permanent magnet, Synchronous, High torque at low rotational speeds, High power density, (High concentration of heat). Annular inlet: Very compatible with PM motors, (Provides cooling where needed, No need for complicated ducting, Leads to a larger motor diameter which is beneficial for motor torque) Effect of prop wash on heat transfer coefficients: Assumed propeller induced turbulence would increase heat transfer coefficients, Holmes, Obara Yip reported 'propeller slipstream showed little if any apparent effect of the slip stream', Derlaga @ LaRC also found little change in heat transfer in the wake of the propeller.

Aircraft↗
NASA NTRSDate not supplied

Numerical Investigation of Heat Transfer on the NASA SIDRM Model

NASA has developed a Simulated Inter-Duct Research Model (SIDRM) to study ice crystal icing in aircraft engines. A numerical investigation has been completed using the NASA in-house code, GlennHT. For each flow condition, many different wall thermal boundary conditions were imposed. Six uniform wall temperature cases were generated, with wall temperature relative to the freestream total temperature of 0.85, 0.90, 0.95, 1.05, 1.10, and 1.15. In addition, five cases with uniform heat flux were generated. Heat fluxes were chosen to generate average wall temperatures in the range explored by the uniform wall temperature cases. Included in the uniform heat flux cases is the adiabatic case where heat flux equals zero. The results of these simulations are then used to quantify the degree to which the heat transfer coefficient depends on wall thermal boundary condition. It is seen that the heat transfer coefficient is fairly independent of wall thermal boundary condition, as expected. However, it would appear that, at least in some locations, it may be prudent to attempt to correlate a variation of heat transfer coefficient with wall thermal boundary condition.

Ice Crystal Icing↗
DOE OSTI2022

Enhanced convection for higher module and system efficiency (Final Technical Report)

The goal of this work is to develop new solar photovoltaic (PV) modules and solar system-scale designs that promote an increase of the convective heat transfer coefficient of at least 40%, reducing the operating temperature of the solar PV panels, and leading to a boost on the annual energy yield by at least 5%. By achieving this goal, we further foresee decreasing solar panel degradation by +0.3%/year, reducing the LCOE by 2.9-4.5¢/kWh. Currently, this question and/or approach is not considered though it is a relevant factor in performance/efficiency. The technology proposed will be at a mature stage by the end of the project and could be aligned to be proven on a full-field test. PV users, installers and manufacturers will be interested in the technology due to the aforementioned benefits. The work was conducted through a suite of wind tunnel experiments, numerical simulations and field experiments. These were then evaluated through a correlation encompassing the entire data set and implementing findings into NREL SAM. The work resulted in eight peer reviewed publications with three others in preparation. The key results of the project are 1.) Showing the capability of increasing the solar farm power production by increasing the heat transfer coefficient; 2.) Providing strategies for achieving this through large scale arrangement manipulation (heights, spacings, angles), flow deflectors and vortex generators; 3.) Demonstrating scalability of results by comparing numerical simulations, wind tunnel experiments and field experiments; 4.) Providing a correlation to be able to capture the various arrangements while exploiting the heat transfer coefficient; and 5.) Proving the feasibility of such strategies and their capacity through a comprehensive techno-economic analysis. For the heat transfer coefficients, gains of 40% were attained and increases in power in the excess of 5% were observed. For heat mitigation strategies, consideration at the PV array scale were inter-panel spacing, panel height and panel angles while at the module level, wind breaks such as solid walls and selected gaps were evaluated as well as vortex generators on the panel. All proposed strategies saw an increase in heat transfer coefficient. For scalability, results were compared against field experiments and a correlation for the heat transfer quantity was attained leading to a parametric understanding of the variations and impact in the heat transfer coefficient independent of tools implemented (wind tunnel/numerical simulations). The strategies were also further assessed by a technoeconomic analysis finding improvements based on LCOE with respect to location (several states with varies atmospheric conditions/geographic locations) yielded different results. Improvements on this end were also observed especially towards the colder climates and when considering bi-facial modules. The quantitative demonstrations of such conclusions are provided in the main portion of this document with complementary results and their narration. Milestones and go/no-go points were successfully met in the project.

14 SOLAR ENERGY↗
NASA NTRS2002

Thermal Analysis and Correlation of the Mars Odyssey Spacecraft's Solar Array During Aerobraking Operations

The Mars Odyssey spacecraft made use of multipass aerobraking to gradually reduce its orbit period from a highly elliptical insertion orbit to its final science orbit. Aerobraking operations provided an opportunity to apply advanced thermal analysis techniques to predict the temperature of the spacecraft's solar array for each drag pass. Odyssey telemetry data was used to correlate the thermal model. The thermal analysis was tightly coupled to the flight mechanics, aerodynamics, and atmospheric modeling efforts being performed during operations. Specifically, the thermal analysis predictions required a calculation of the spacecraft's velocity relative to the atmosphere, a prediction of the atmospheric density, and a prediction of the heat transfer coefficients due to aerodynamic heating. Temperature correlations were performed by comparing predicted temperatures of the thermocouples to the actual thermocouple readings from the spacecraft. Time histories of the spacecraft relative velocity, atmospheric density, and heat transfer coefficients, calculated using flight accelerometer and quaternion data, were used to calculate the aerodynamic heating. During aerobraking operations, the correlations were used to continually update the thermal model, thus increasing confidence in the predictions. This paper describes the thermal analysis that was performed and presents the correlations to the flight data.

Dec, John A.↗
DOE OSTI2024

Enhancing particle-to-sCO2 heat exchanger effectiveness through novel high-porosity metallic foams

In this project, a novel concept of Octet-shape based lattice frame material was developed for deployment in particle-to-sCO2 heat exchangers for CSP application. A comprehensive experimental and numerical program was performed to investigate and characterize the thermal and flow transport behavior in high porosity lattice frame material. The thermal properties include effective thermal conductivity and interstitial heat transfer coefficient and flow properties including permeability and inertial coefficient. Above quantities were determined for both air flow and heated particle flow through the porous channels which were representative of the hot channel in a typical counter flow heat exchanger. The cold side of the heat exchanger feature minichannels which are known to be very efficient in thermal transport. The goal of this project was to enhance the overall heat transfer coefficient (Up) on the hot side by introducing Octet-shape based lattice frame material through enhancement in effective thermal conductivity of the channel and through enhancement in the interstitial heat transfer coefficient.

14 SOLAR ENERGY↗
NASA NTRS1993

Vaporization heat transfer of dielectric liquids on enhanced surfaces covered with screen wicks

Experiments were conducted to investigate the vaporization heat transfer characteristics for the dielectric liquid FC-72 on several wicking surfaces which may be used in flat-plate heat pipes. The wicking materials studied included microstructure enhanced surfaces and coarse surfaces covered with screen meshes. Experimental data for q versus deltaT curves and critical heat fluxes were obtained for the two different operating conditions of a heat pipe, evaporation, and shallow pool boiling. When the liquid level was above the heated surface, the height of the liquid level above the surface was varied from 0 to 10 mm. When the liquid level was below the heated surface, the distance from the liquid level to the edge of the surface was adjusted from 0 to 15 mm. Experimental results revealed that for shallow pool boiling when the heated surface was covered with a wire screen mesh, the heat transfer coefficient increased at lower heat fluxes but the critical heat flux (CHF) decreased for all the surfaces tested. In the case of evaporation, both CHF and the heat transfer coefficient increased as the microstructure surfaces were covered with screen meshes.

Gu, C. B.↗
DOE OSTI2020

Chapter 14: Heat and Mass Transfer

Fluidized beds are used in a variety of processes due to their excellent heat and mass transfer properties. Heat transfer in fluidized beds can refer to interphase heat transfer, or more commonly to bed-to-surface heat transfer. Heat transfer between bubble phase and dense phase can be characterized by an interphase heat transfer coefficient. This chapter elaborates the derivation of the interphase heat transfer coefficient by an analogy to mass transfer. Mass transfer in fluidized beds usually refers to gas-to-particle mass transfer, or interphase mass transfer, where a component migrates from particles to fluids, or vice versa. The chapter describes the two major components of the interphase mass transfer: particle and fluid mass transfer in the dense phase; and bubble- to dense-phase mass transfer.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS↗
NASA NTRS1997

Heat Transfer Measurements on Surfaces with Natural Ice Castings and Modeled Roughness

An experimental method is described to measure and compare the convective heat transfer coefficient of natural and simulated ice accretion roughness and to provide a rational means for determining accretion-related enhanced heat transfer coefficients. The natural ice accretion roughness was a sample casting made from accretions at the NASA Lewis Icing Research Tunnel (IRT). One of these castings was modeled using a Spectral Estimation Technique (SET) to produce three roughness elements patterns that simulate the actual accretion. All four samples were tested in a flat-plate boundary layer at angle of attack in a "dry" wind tunnel test. The convective heat transfer coefficient was measured using infrared thermography. It is shown that, dispite some problems in the current data set, the method does show considerable promise in determining roughness-induced heat transfer coefficients, and that, in addition to the roughness height and spacing in the flow direction, the concentration and spacing of elements in the spanwise direction are important parameters.

Breuer, Kenneth S.↗
DOE OSTI2025

Performance Evaluation of Low-Cost Condensers Immersed in the Water Tank of a Heat Pump Water Heater

This paper reports the effect of low-cost immersed condensers on the performance of a heat pump water heater (HPWH) that does not require a water-circulating pump. The proposed design is based on the immersion of an L-style condenser coil through an opening in the top of the water tank. The novel design aims to eliminate the need for the water-circulating pumps, thereby substantially improving efficiency and reducing costs and maintenance of the HPWH system. Comprehensive computational fluid dynamics (CFD) simulations and experimental tests were performed, and the results showed that the CFD simulations were close to the experimental data. Further results confirm that the L-style condenser can introduce buoyancy-driven flow and eliminate temperature stratification in the studied HPWH water tank, thereby improving the heat transfer coefficient and coefficient of performance of the HPWH. The testing results further showed that the L-style condenser enabled more than 53% higher coefficient of performance and 400% higher heat transfer coefficient compared with the straight vertical condenser, and achieved much faster water heating. Furthermore, the effects of immersed condensers with different circuits on the HPWH performance were evaluated and compared. All results indicate that the current energy-saving and inexpensive HPWH technology is technically valid, and the benefits of performance improvement and low cost are attractive in future HPWH design.

Gao, Zhiming [ORNL] (ORCID:0000000271397995)↗
NASA NTRS1989

Simulating transitional flow and heat transfer over the flat plate and circular cylinder using a K-epsilon turbulence model

A boundary layer computer code, called TEXSTAN, has been used to simulate external, transitional, fluid flow and heat transfer over the flat plate and circular cylinder. Turbulence modeling was accomplished by using a low-Reynolds number K-epsilon turbulence model. The study was made for free-stream turbulence intensities less than 15 percent. The comparison of the flat plate heat transfer predictions to experimental data showed good agreement, for the location of transition as well as in the heat transfer coefficient. The typical discrepancy in predicting the heat transfer coefficient was less than 5 percent of the measured value.

Sullivan, T. J.↗
NASA NTRS1997

Heat Transfer Computations of Internal Duct Flows With Combined Hydraulic and Thermal Developing Length

This study investigated the Navier-Stokes computations of the surface heat transfer coefficients of a transition duct flow. A transition duct from an axisymmetric cross section to a non-axisymmetric cross section, is usually used to connect the turbine exit to the nozzle. As the gas turbine inlet temperature increases, the transition duct is subjected to the high temperature at the gas turbine exit. The transition duct flow has combined development of hydraulic and thermal entry length. The design of the transition duct required accurate surface heat transfer coefficients. The Navier-Stokes computational method could be used to predict the surface heat transfer coefficients of a transition duct flow. The Proteus three-dimensional Navier-Stokes numerical computational code was used in this study. The code was first studied for the computations of the turbulent developing flow properties within a circular duct and a square duct. The code was then used to compute the turbulent flow properties of a transition duct flow. The computational results of the surface pressure, the skin friction factor, and the surface heat transfer coefficient were described and compared with their values obtained from theoretical analyses or experiments. The comparison showed that the Navier-Stokes computation could predict approximately the surface heat transfer coefficients of a transition duct flow.

Wang, C. R.↗
NASA NTRSDate not supplied

Flow Boiling and Condensation Experiment (FBCE): Summary of Findings for Flow Boiling based on Completed ISS Experiments

Since 2011, researchers from Purdue University and NASA Glenn Research Center (GRC) have been collaborating to investigate the effects of gravity on several aspects of flow boiling and flow condensation. This massive research endeavor, termed the Flow Boiling and Condensation Experiment (FBCE), has culminated in development of NASA’s largest and most complex facility for investigation of two-phase fluid physics onboard the ISS. FBCE consists of two separate studies: flow boiling, using the Flow Boiling Module (FBM), and flow condensation, using the Condensation Module for Heat Transfer Measurements (CM-HT); this presentation concerns the FBM portion of FBCE. Fitted with FBM, FBCE was launched to the ISS in August 2021 and experiments were successfully performed starting in February 2022 to amass a large microgravity-flow-boiling database supported by extensive visualization of interfacial behavior using high-speed video. Based on FBCE experiments performed previously in Earth gravity and parabolic flight, along with the new ISS data, several empirical correlations, theoretical models, and CFD models have been developed, enabling the prediction of crucial flow boiling parameters, including heat transfer coefficient and critical heat flux (CHF). These predictive tools, which will be summarized in this presentation, are expected to serve as foundation for design of future space systems involving flow boiling.

Two-phase flow and phase transition↗
NASA NTRS1985

Characteristics of heat exchange in the region of injection into a supersonic high-temperature flow

An experimental investigation of the local heat transfer coefficient distribution during gas injection into the supersonic-flow portion of a Laval nozzle is discussed. The controlling dimensionless parameters of the investigated process are presented in terms of a generalized relation for the maximum value of the heat transfer coefficient in the nozzle cross section behind the injection hole. Data on the heat transfer coefficient variation along the nozzle length as a function of gas injection rate are also presented, along with the heat transfer coefficient distribution over a cross section of the nozzle.

Bakirov, F. G.↗
NASA NTRS2019

Assessment of a One-Dimensional Finite Element Charring Ablation Material Response Model for Phenolic-Impregnated Carbon Ablator

In this study, mathematical formulations to model charring ablation problems were numerically implemented using finite element analysis (FEA) with ABAQUS, which account for the material decomposition and progressive surface removal in the heat conduction and the surface energy balance equations. FEA was performed for a one-dimensional model to predict the temperature and ablation histories of a phenolic-impregnated carbon ablator sample (i.e., a common heat shield material for hypersonic vehicles and spacecraft) subjected to oxy-acetylene torch flame (i.e., 0.8 SLPM acetylene gas to 2.7 SLPM oxygen gas). The recovery enthalpy and convective heat transfer coefficient for the ablation model were calculated based on gas compositions and two assumed surface conditions (i.e., equilibrium and frozen). Simulations using the calculated recovery enthalpy and convective heat transfer coefficient resulted in a recession rate of 6.38 times (equilibrium) and 14.08 times (frozen) higher than the experimental data, despite fair agreement of the surface temperature. In addition, the effect of the heat transfer coefficient was investigated through a steady-state ablation analysis. The results of the analysis indicate that there is not one single value for the heat transfer coefficient that would allow the prediction to match both measured recession rate and surface temperature. Possible reasons for such an inconsistency are provided and discussed.

Thermal Protection System↗
NASA NTRS1961

Heat-Transfer Measurements at a Mach Number of 4.95 on Two 60 deg Swept Delta Wings with Blunt Leading Edges and Dihedral Angles of 0 deg and 45 deg

An experimental investigation was conducted to evaluate the heat-transfer characteristics of two 60 deg swept delta wings with cylindrical leading edges of 0.25-inch radii and dihedral angles of 0 deg and 45 deg. The tests were conducted at a Mach number of 4.95 and a stagnation temperature of 400 F. The The test-section unit Reynolds number was varied from 1.95 x 10(exp 6) to 12.24 x 10(exp 6) per foot. The results of the investigation indicated that, in a plane normal to the leading edge, the laminar-flow heat-transfer distribution was in good agreement with two-dimensional blunt-body theory. The stagnation-line heat-transfer level could be predicted from two-dimensional blunt-body theory provided the stagnation-line heat-transfer coefficient was assumed to vary as the cosine of the effective sweep. A comparison of the heating rates to the 0 deg dihedral wing (planform sweep of 60 deg) and the 45 deg dihedral wing (planform sweep of 69.3 deg) with equal panel sweep and panel area indicated that the stagnation-line heat-transfer coefficient for the 45 deg dihedral wing could be as much as 40 percent less than the stagnation-line heat-transfer coefficient for the 0 deg dihedral wing at both equal angles of attack and equal lifts. The laminar-flow heat-transfer rate to both wings outside the vicinity of the stagnation line was essentially equal.

Stainback, P. Calvin↗
NASA NTRS1985

Effects of cooling system parameters on heat transfer in PAFC stack

Analytical and experimental study for the effects of cooling system parameters on the heat transfer and temperature distribution in the electrode plates of a phosphoric acid fuel-cell has been conducted. An experimental set-up that simulates the operating conditions prevailing in a phosphoric-acid fuel-cell stack was designed and constructed. The set-up was then used to measure the overall heat transfer coefficient, the thermal contact resistance, and the electrode temperature distribution for two different cooling plate configurations. Two types of cooling plate configurations, serpentine and straight, were tested. Air, water, and oil were used as coolants. Measurements for the heat transfer coefficient and the thermal contact resistance were made for various flow rates ranging from 16 to 88 Kg/hr, and stack clamping pressure ranging from O to 3448 Kpa. The experimental results for the overall heat transfer coefficient were utilized to derive mathematical relations for the overall heat transfer coefficient as a function of stack clamping pressure and Reynolds number for the three coolants. The empirically derived formulas were incorporated in a previously developed computer program to predict electrodes temperature distribution and the performance of the stack cooling system. The results obtained were then compared with those available in the literature. The comparison showed maximum deviation of +/- 11%.

Abdul-Aziz, Ali A.↗
DOE OSTI2023

Investigation of Technologies to Improve Condenser Heat Transfer and Performance in a Relevant Coal-Fired Power Plant

Improvements in thermal power-generating plant performance is correlated directly to societal benefits including lower cost of reduced fuel consumption, resulting in lower cost of electricity for the consumer and reduced carbon emissions to the atmosphere. Warm steam exhausted from low-pressure steam turbines is condensed to liquid water on the exterior of thin-walled metal condenser tubes with cooling water passing through the tube interior. The condensation of steam creates a vacuum that supports turbine rotation and the concurrent generation of electricity. This vacuum is optimized when heat transfer across the wall of condenser tube is maximized. Common hindrances to heat transfer include foulants in cooling water that may form and adhere to the interior of condenser tubes, including mineral scale, microbiological films, and particulate deposition. Flowing cooling water may also include a laminar layer at the interior metal surfaces that travels more slowly than bulk water flow, serving to impede heat transfer. On the tube exterior, condensing steam forms an insulating layer of water that flows down the tube and reduces the effectiveness of cooling. Both the interior and exterior barriers to optimal heat transfer may be alleviated to some extent by surface treatments. On the tube interior, hydrophobic coatings may be applied that can reduced the adherence of foulants and of the laminar flow layer to the tube surface. On the tube exterior, hydrophobic coatings or mechanical treatments can be applied that may result in the termination of droplet growth and the departure of droplets from the surface rather than coalescence into a continuous layer of flowing water. Fourteen surface treatments were applied to condenser tubes in this study, including eight interior coatings and six exterior treatments, five of which were coatings and one a microstructural texture. Heat transfer measurement equipment simulating conditions in the condenser of an operating power plant was used to determine heat transfer coefficients by measuring sufficient flow, temperature, water chemistry and other data. Several of the tubes with interior surface treatments showed improvement in heat transfer coefficients compared with a plain (uncoated) tube, and several of the tubes with exterior surface treatments also showed enhanced heat transfer coefficients.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1995

Numerical thermal analyses of heat exchangers for the stirling engine application

The Regenerator, Cooler and Heater for the NASA Space Power Research Engine (SPRE) have been analyzed in detail for laminar, incompressible and oscillatory flow conditions. Each component has been analyzed independently and in detail with the regenerator being modeled as two-parallel-plates channel with a solid wall. The ends of the channel are exposed to two reservoir maintained at different temperature thus providing an axial temperature gradient along the channel. The cooler and heater components have been modeled as circular pipes with isothermal walls. Two different types of thermal boundary conditions have been investigated for the cooler and heater, namely, symmetric and asymmetric temperature inflow. In symmetric temperature inflow the flow enters the channel with the same temperature in throughout the velocity cycle whereas, in asymmetric temperature inflow the flow enters with a different temperature in each half cycle. The study was conducted over a wide range of Maximum Reynolds number (RE(max) varying from 75 to 60000, Valensi number (Va) from 2.5 to 800, and relative amplitude of fluid displacement (A(sub r) from 0.357 to 1.34. A two dimensional Finite volume method based on the SIMPLE algorithm was used to solve the governing partial differential equations. Post processing programs were developed to effectively describe the heat transfer mechanism under oscillatory flows. The computer code was validated by comparing with existing analytical solutions for oscillating flows. The thermal field have been studied with the help of temperature contour and three dimensional plots. The instantaneous friction factor, wall heat flux and heat transfer coefficient have been examined. It has been concluded that in general, the frictional factor and heat transfer coefficient are higher under oscillatory flow conditions when the Valensi number is high. Also, the thermal efficiency decreases for lower A(r) values. Further, the usual steady state definition for the heat transfer coefficient does not seem to be valid.

Kannapareddy, Mohan Raj↗