Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “foams”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Foam-lined hohlraum, inertial confinement fusion experiments on the National Ignition Facility

Experiments on the National Ignition Facility (NIF) to study hohlraums lined with a 20-mg/cc 400-μm-thick Ta 2 O 5 aerogel at full scale (hohlraum diameter = 6.72 mm) are reported. Driven with a 1.6-MJ, 450-TW laser pulse, the performance of the foam liner is diagnosed using implosion hot-spot symmetry measurements of the high-density carbon (HDC) capsule and measurement of inner beam propagation through a thin-wall 8-μm Au window in the hohlraum. Results show an improved capsule performance due to laser energy deposition further inside the hohlraum, leading to a modest increase in x-ray drive and reduced preheat due to changes in the x-ray spectrum when the foam liner is included. In addition, the outer cone bubble uniformity is improved, but the predicted improvement in inner beam propagation to improve symmetry control is not realized for this foam thickness and density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Foam and Unreacted Material Reduction in Magnesium Oxysulfate for SRPPF Waste Solidification

A magnesium oxysulfate (MOS) grout formulation has been proposed to solidify the liquid effluent from the Savannah River Plutonium Processing Facility (SRPPF) Aqueous Recovery System (ARS). This formulation uses a combination of light-burnt MgO, anhydrous MgSO 4 , and dead-burnt MgO resulting in a grout with good mixability and acceptable density. The setting time for the grout is within the operational limits of the SRPPF facility and the leachate pH is ~9.4, which is within the assumed pH range of the brine from the Waste Isolation Pilot Plant (WIPP). When first tested at the 1-gallon small-scale and 55-gallon full-scale, there was a significant foam layer that raised concerns of a nonhomogeneous final form. A nonhomogeneous mixture could have variable density throughout the waste form and therefore allow for unequal shielding. To reduce the potential for unequal shielding in the final form, a series of foam reduction tests were carried out and a final formulation of 28 wt% light burnt MgO, 10 wt% MgSO 4 , and 62 wt% dead burnt MgO was used to remove the foam in under two hours while still maintaining a mix that has an acceptable density, mix time, peak temperature, and set time.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

FY25 Cellular Silicone Foam Friction Testing Summary Report

This effort was a collaboration between LANL groups MPA-CINT, E-13, and V-14 to characterize various properties of foam materials for programmatic work. Specifically, MPA-CINT staff members’ contribution to this effort was to perform friction testing of cellular silicone foams of two different porosities with respect to two engineering materials with predefined surface roughnesses. The selected foams (henceforth serving as the sled material interface exposed to motion) had porosities of 67% and 70% with respect to fabricated values. The other materials used in the friction testing measurement couple (static track material) were 304 Stainless Steel (304 SS) and Very High-Temperature Glass-Mica Ceramic, known as Macor®.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sustainable Wood-Waste-Based Thermal Insulation Foam for Building Energy Efficiency

Wood is one of the most abundant biomaterials on Earth, which has been used for centuries in construction applications including furniture, roofing, flooring, and cabinetry. However, wood chips—which are a low-quality and plentiful waste byproduct of lumber milling, woodworking, and shipping operations—have low economic value and complicated disposal methods. In this paper, we propose a strategy for wood chip reuse through the fabrication of bio-based building insulation foam. Through a high-temperature chemical treatment delignification process, we introduced additional small pores within the wood chips, effectively lowering their thermal conductivity, and used them in combination with a binding agent to produce a porous insulation foam. The porous insulation foam achieved a low thermal conductivity of 0.038 W/(m·K) and a high compressive strength of 1.1 MPa (70% strain). These characteristics demonstrate that wood waste can be repurposed into an effective building material, addressing challenges in both waste management and sustainable construction.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Microfluidic Fabrication Techniques for High-Pressure Testing of Microscale Supercritical CO 2 Foam Transport in Fractured Unconventional Reservoirs

Pressure limitations of many microfluidic platforms have been a significant challenge in microfluidic experimental studies of fractured media. As a result, these platforms have not been fully exploited for direct observation of high-pressure transport in fractures. This work introduces microfluidic platforms that enable direct observation of multiphase flow in devices featuring surrogate permeable media and fractured systems. Such platforms provide a pathway to address important and timely questions such as those related to CO 2 capture, utilization and storage. This work provides a detailed description of the fabrication techniques and an experimental setup that may serve to analyze the behavior of supercritical CO 2 (scCO 2 ) foam, its structure and stability. Such studies provide important insights regarding enhanced oil recovery processes and the role of hydraulic fractures in resource recovery from unconventional reservoirs. This work presents a comparative study of microfluidic devices developed using two different techniques: photolithography/wet-etching/ thermal-bonding versus Selective Laser-induced Etching. Both techniques result in devices that are chemically and physically resistant and tolerant of high pressure and temperature conditions that correspond to subsurface systems of interest. Both techniques provide pathways to high-precision etched microchannels and capable lab-on-chip devices. Photolithography/wet-etching, however, enables fabrication of complex channel networks with complex geometries, which would be a challenging task for laser etching techniques. This work summarizes a step-by-step photolithography, wet-etching and glass thermal-bonding protocol and, presents representative observations of foam transport with relevance to oil recovery from unconventional tight and shale formations. In conclusion, this work describes the use of a high resolution monochromatic sensor to observe scCO 2 foam behavior where the entirety of the permeable medium is observed simultaneously while preserving the resolution needed to resolve features as small as 10 μm.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Develop Renewable/Sustainable Material to Displace Petroleum-Derived Polymer Foams (CRADA Final Report)

NLR and EDEN will partner together to develop renewable, biodegradable alternatives to polyfoam (polyurethane) polymer foams. The initial focus will be on developing cellulose-based foam with tunable mechanical properties. NLR will produce and test the cellulose-based foam materials and characterize its microstructure and mechanical properties. Relationships between mechanical performance formulation and fabrication methods will be developed.

09 BIOMASS FUELS↗
DOE OSTI2020

Surface modification of polymer foams using plasma

An embodiment includes a system comprising: a monolithic shape memory polymer (SMP) foam having first and second states; wherein the SMP foam includes: (a) polyurethane, (b) an inner half portion having inner reticulated cells defined by inner struts, (c) an outer half portion, having outer reticulated cells defined by outer struts, surrounding the inner portion in a plane that provides a cross-section of the SMP foam, (d) hydroxyl groups chemically bound to outer surfaces of both the inner and outer struts. Other embodiments are discussed herein.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Surface modification of polymer foams using plasma

An embodiment includes a system comprising: a monolithic shape memory polymer (SMP) foam having first and second states; wherein the SMP foam includes: (a) polyurethane, (b) an inner half portion having inner reticulated cells defined by inner struts, (c) an outer half portion, having outer reticulated cells defined by outer struts, surrounding the inner portion in a plane that provides a cross-section of the SMP foam, (d) hydroxyl groups chemically bound to outer surfaces of both the inner and outer struts. Other embodiments are discussed herein.

Nash, Landon D.↗
DOE OSTI2023

Experimental investigation on nucleate boiling heat transfer of low GWP refrigerants over metal-foam enhanced tube bundles

The objective of this work is to develop an enhanced tube bundle to improve the nucleate boiling heat transfer for the application of flooded evaporators. The enhanced tube bundle was made by deploying metal foam around the outer surface of aluminum tubes, which provide higher heat transfer area and nucleation site density. The pool boiling experiments for horizontal tube bundles were conducted in a pressure vessel at difference heat fluxes. The heat transfer performance of bare aluminum tube bundle was compared against the metal-foam enhanced tube bundle using low GWP refrigerant, R-1234yf. The experimental results showed that the heat transfer coefficient of the metal-foam enhanced tube bundle was at least two times higher than that of the bare tube bundle, and the enhancement ratio depended on the heat flux condition.

Yang, Cheng-Min↗
DOE OSTI2024

Stent with expandable foam

A system comprising first, second, and third shape memory polymers (SMPs); wherein (a) the first SMP is a biodegradable open cell foam that includes a first channel; (b) the second SMP includes a second channel and is included in the first channel; (c) the foam is in a first state and is configured to expand to a second state, radially outward from the second foam, in response to thermal stimulus; (d) the third SMP is between the first and second SMPs and includes a stent having a first strut that includes the third SMP and a second strut that includes the third SMP; and (e) each of the first, second, and third SMPs is coupled to a wire.

Wilson, Thomas S.↗
DOE OSTI2025

Hygroscopic Metal-Complex Coated Metal Foam for Moisture Management

Moisture management for improving indoor air quality is critical for health and thermal comfort. Recently, the use of desiccant-coated heat exchangers (HXs) has emerged as a promising dehumidification approach to reduce energy consumption as compared with conventional vapor compression-based air dehumidification. The desiccant material is a key component of dehumidification performance. However, currently used desiccant materials have a low moisture uptake capability and require a high temperature for regeneration. The current study investigated the dehumidification performance of a metal-complex-based hygroscopic desiccant-coated metal foam HX. Furthermore, the results revealed that the desiccant-coated foams display increased hydrophilicity compared with the uncoated metal surfaces. Additionally, the desiccant coating had superior moisture absorption capability of more than 2 g/g desiccant , which is much higher than commonly used zeolite and silica gels. Wind tunnel experiments showed that the coating absorbs moisture from humid air and can be effectively regenerated at low temperatures. Additionally, the coating did not increase the pressure drop of the HX. Overall, the results of this study suggest that this desiccant-coated metal form can potentially be used for moisture management in the building sector.

Atmospheric chemistry↗
DOE OSTI2026

Metal Foam Morphology Affects the Run to Run Reproducibility of OER Using Nickel Catalysts

Nickel (Ni) foam-based electrodes are excellent catalysts for the oxygen evolution reaction; however, we found that the random pore-size distribution of Ni foams contributes to a significant variability in electrochemically active surface area, compromising experimental reproducibility. We provide insights into quantifying this critical material property, verified by four electrochemical laboratories.

25 ENERGY STORAGE↗
DOE OSTI2024

Green co-solvent-assisted one-pot synthesis of high-performance flexible lignin polyurethane foam

Although lignin is a promising candidate as a source of polyol for producing eco-friendly polyurethane foam (PUF), its direct application has limitations, primarily stemming from the brittleness of the resulting products and poor processibility at high lignin loadings. To address these technical challenges, we introduced an effective co-solvent for the lignin-based polyurethane foams (LPUFs) with up to 80wt% of lignin substitution for petroleum polyols. As a green co-solvent that involves carbon dioxide fixation during its production, propylene carbonate (PC), was blended with lignin and improved the distribution of lignin by decreasing the viscosity, providing a room-temperature reaction. The LPUFs demonstrated a comparable thermal insulation performance (R-values greater than 5 in -1 ) with commercially available PUF with a uniform size of closed-cell structure induced by the reduced viscosity of lignin-based polyol. LPUFs also showed enhanced fire retardancy and moisture resistance compared to the control PUFs, benefiting from lignin’s intrinsic fire-resistant and hydrophobic properties. To mitigate the brittleness issue at high lignin loadings, flexible polyethylene glycols (PEGs) with a high molecular weight (i.e., PEG-1000) were dissolved in PC at room temperature to further improve the mechanical strength of LPUFs. The compressive strength of LPUFs with 80 wt% lignin substitution content was remarkably improved to 226 kPa by the employment of co-solvent and PEG-1000 compared to the control PUF (<140 kPa). Moreover, the flexibility of the LPUFs was successfully controlled by simply adjusting the PEG-400/PEG-1000 ratio. In conclusion, the results of this study provide valuable insights for accelerating and broadening the utilization of lignin in sustainable materials and manufacturing areas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Glass production rate in an electric melter: Melting rate correlation and primary foam stability

Waste loading and melting rate are major factors determining the lifecycle of nuclear waste disposal by vitrification in electric melters in which the heat to the cold cap is delivered from the melt pool. One of the crucial parameters that affect the rate of melting is the temperature at which the primary foam collapses at the cold cap bottom. Further, apart from the transient glass-forming melt viscosity, primary foam stability is affected by the shear stress imposed by the flow in the melt pool and the presence of residual solid particles.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Valorisation of technical lignin in rigid polyurethane foam: A critical evaluation on trends, guidelines and future perspectives

Lignin is one of the most abundant aromatic natural polymers. Produced as a by-product from the biomass refinery industries, lignin remains largely underutilised in high-value industrial applications. The incorporation of lignin in rigid polyurethane foam (RPUF) has been the focus of much research, due to its potential to replace fossil fuel-based components of RPUF. However, the overall sustainability of RPUF depends on numerous factors including processability, cost-effectiveness, and retention of performance throughout the service life. To date, the incorporation of lignin has been explored either as filler particles (through direct incorporation) or as a blendable liquid polyol introduced after chemical modifications (such as oxyalkylation, functionalisation, or depolymerisation). However, the production of lignin incorporated foam with high performance through cost-effective processing is still an ongoing challenge. Herein, this review critically appraises the progress on the effective incorporation of lignin in RPUF. Firstly, this review briefly covers the essential raw materials, formulation, important properties, and sustainability aspects of RPUF for industrial applications. Secondly, it provides insights on the key parameters of lignin of relevance to incorporation into RPUF. Thirdly, it benchmarks the reported studies on incorporation of lignin in RPUF systems by evaluating their important properties and proposes potential strategies for addressing the key challenges in the incorporation of lignin in RPUF. By bridging the gaps that exist in the literature on the utilisation of lignin in RPUF this account will serve as a resource for both beginners and professionals in the polyurethane and biorefinery industries towards the successful development of lignin incorporated RPUF for industrial applications

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Non-solvents as physical blowing agents in printable silicone foams

Silicone foams were produced by dispersing an incompatible liquid phase (i.e. a non-solvent) into an uncured, liquid silicone. The formulation and processing parameters were varied to see the effect on porosity and pore morphology. Specifically, two fluorosilanes were added to stabilize the inclusion of fluorinated solvents as blowing agents. As the floruosilane content increased, the void content increased up to about 44 vol. % when the fluorosilane comprised 18 wt. % of the initial formulation. Fumed silica that was treated with a fluorinated silane was also used to try to stabilize the dispersed liquid. While the fumed silica content did not have a strong effect on the total void content, the morphology changed when silica content changed. Various fluorinated solvents with distinct chemical structures were used as the non-solvent and then removed after curing of the silicone. The interaction of the internal non-solvent phase and the silicone phase was expected to influence the porosity. These insights highlight how the manipulation of formulation and processing parameters, focusing on the inclusion of fluorosilanes and fluorinated solvents, contributes to the understanding of how incompatible liquid phases interact with silicone matrices to control porosity and pore morphology. Additionally, these interactions also influenced processability, leading to formulations that could be printed. Higher content of non-solvent inclusions could increase the yield stress and storage modulus of an uncured formulation, leading to the ability to tune intrastrand porosity while a 3D printed architecture could be modified to introduce porosity between the strands. Furthermore, in addition to fluorinated solvents, we also considered non-fluorinated solvents since these may be more industrially relevant in the future. Overall, this approach provides an alternative route to producing porous foams that can be 3D printed, which could be useful for applications like cushioning and protective gear.

physical blowing agent↗