Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fault motion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Pendulum Motion in Main Parachute Clusters

The coupled dynamics of a cluster of parachutes to a payload are notoriously difficult to predict. Often the payload is designed to be insensitive to the range of attitude and rates that might occur, but spacecraft generally do not have the mass and volume budgeted for this robust of a design. The National Aeronautics and Space Administration (NASA) Orion Capsule Parachute Assembly System (CPAS) implements a cluster of three mains for landing. During testing of the Engineering Development Unit (EDU) design, it was discovered that with a cluster of two mains (a fault tolerance required for human rating) the capsule coupled to the parachute cluster could get into a limit cycle pendulum motion which would exceed the spacecraft landing capability. This pendulum phenomenon could not be predicted with the existing models and simulations. A three phased effort has been undertaken to understand the consequence of the pendulum motion observed, and explore potential design changes that would mitigate this phenomenon. This paper will review the early analysis that was performed of the pendulum motion observed during EDU testing, summarize the analysis ongoing to understand the root cause of the pendulum phenomenon, and discuss the modeling and testing that is being pursued to identify design changes that would mitigate the risk.

Ray, Eric S.↗
DOE OSTI2021

Single-Particle Studies Reveal a Nanoscale Mechanism for Elastic, Bright, and Repeatable ZnS:Mn Mechanoluminescence in a Low-Pressure Regime

Mechanoluminescent materials, which emit light in response to elastic deformation, are demanded for use as in situ stress sensors. ZnS doped with Mn is known to exhibit one of the lowest reported thresholds for appearance of mechanoluminescence, with repeatable light emission under contact pressure <10 MPa. Here, the physical basis for such behavior remains as yet unclear. Here, reliable microscopic detection of mechanoluminescence of single ZnS:Mn microparticles, in combination with nanoscale structural characterization, provides evidence that the mechanoluminescent properties of these particles result from interplay between a non-centrosymmetric crystal lattice and its defects, viz., dislocations and stacking faults. Statistical analysis of the distributions of mechanoluminescence energy release trajectories reveals two distinct mechanisms of excitation: one attributable to a piezo-phototronic effect and the other due to dislocation motion. At pressures below 8.1 MPa, both mechanisms contribute to mechanoluminescent output, with a dominant contribution from the piezo-phototronic mechanism. In contrast, above 8.1 MPa, dislocation motion is the primary excitation source. For the piezo-phototronic mechanism, we propose a specific model that accounts for elastic ZnS:Mn mechanoluminescence under very low pressure. The charged interfaces in stacking faults lead to the presence of filled traps, which otherwise would be empty in the absence of the built-in electric field. Upon application of external stress, local enhancement of the piezoelectric field at the stacking faults’ interfaces facilitates release of the trapped carriers and subsequent luminescence. This field enhancement explains how <10 MPa pressure produces thousands of photons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Highly deformable Mg–Al–Ca alloy with Al 2 Ca precipitates

Magnesium (Mg) is the lightest structural metal. However, the poor formability of Mg alloys to great extent limits their applications in making structural parts. Formability is strongly correlated to both high tensile elongation and large work hardening capacity. In this work, we report a new Mg-Al-Ca alloy in which a majority of deformable Al 2 Ca precipitates form while the formation of Laves phases of Mg 17 Al 12 and Mg 2 Ca seems suppressed. Al 2 Ca precipitates imped dislocation motion, leading to large work hardening. Then, Al 2 Ca precipitates deform with dislocations and stacking faults under the enhanced flow stress, which relieve local stress concentration and improve tensile elongation. In addition, solutes Al and Ca suppress twin nucleation while promoting non-basal dislocations in Mg. Our Mg-Al-Ca alloy demonstrates one of the highest combinations of tensile elongation and work hardening capacity among existing Mg alloys.

36 MATERIALS SCIENCE↗
NASA NTRS1978

Present-day plate motions

An instantaneous plate-motion model, Relative Motion 2 (RM2), is obtained by inverting a data set comprising 110 spreading rates, 78 transform fault azimuths, and 142 earthquake slip vectors. RM2 is compared with angular velocity vectors which best fit the data along individual plate boundaries and, while the model performs close to optimally in most regions, attention is directed to those regions which are not suitably described by the model. Reasons for the discrepancies between RM2 and observations for the India-Antarctica plate boundary, the Pacific-India plate boundary, and the east-west trending transform fault azimuths observed in the French-American Mid-Ocean Undersea Study area are discussed.

Minster, J. B.↗
NASA NTRS1987

Tectonics of the Nazca-Antarctic plate boundary

A new bathymetric chart of part of the Chile transform system is constructed, based mainly on an R/V Endeavor survey from 100 deg W to its intersection with the East Ridge of the Juan Fernandez microplate. A generally continuous lineated trend can be followed through the entire region, with the transform valley being relatively narrow and well-defined from 109 deg W to approximately 104 deg 30 min W. The fracture zone then widens to the east, with at least two probable en echelon offsets to the south at 104 deg and 102 deg W. Six new strike-slip mechanisms along the Chile Transform and one normal fault mechanism near the northern end of the Chile Rise, inverted together with other plate-motion data from the eastern portion of the boundary, produce a new best-fit Euler pole for the Nazca-Antarctic plate pair, providing tighter constraints on the relative plate motions.

Anderson-Fontana, Sandra↗
NASA NTRS2009

Use of QuakeSim and UAVSAR for Earthquake Damage Mitigation and Response

Spaceborne, airborne, and modeling and simulation techniques are being applied to earthquake risk assessment and response for mitigation from this natural disaster. QuakeSim is a web-based portal for modeling interseismic strain accumulation using paleoseismic and crustal deformation data. The models are used for understanding strain accumulation and release from earthquakes as well as stress transfer to neighboring faults. Simulations of the fault system can be used for understanding the likelihood and patterns of earthquakes as well as the likelihood of large aftershocks from events. UAVSAR is an airborne L-band InSAR system for collecting crustal deformation data. QuakeSim, UAVSAR, and DESDynI (following launch) can be used for monitoring earthquakes, the associated rupture and damage, and postseismic motions for prediction of aftershock locations.

fault systems↗
NASA NTRS2007

Deep Space Network Antenna Logic Controller

The Antenna Logic Controller (ALC) software controls and monitors the motion control equipment of the 4,000-metric-ton structure of the Deep Space Network 70-meter antenna. This program coordinates the control of 42 hydraulic pumps, while monitoring several interlocks for personnel and equipment safety. Remote operation of the ALC runs via the Antenna Monitor & Control (AMC) computer, which orchestrates the tracking functions of the entire antenna. This software provides a graphical user interface for local control, monitoring, and identification of faults as well as, at a high level, providing for the digital control of the axis brakes so that the servo of the AMC may control the motion of the antenna. Specific functions of the ALC also include routines for startup in cold weather, controlled shutdown for both normal and fault situations, and pump switching on failure. The increased monitoring, the ability to trend key performance characteristics, the improved fault detection and recovery, the centralization of all control at a single panel, and the simplification of the user interface have all reduced the required workforce to run 70-meter antennas. The ALC also increases the antenna availability by reducing the time required to start up the antenna, to diagnose faults, and by providing additional insight into the performance of key parameters that aid in preventive maintenance to avoid key element failure. The ALC User Display (AUD) is a graphical user interface with hierarchical display structure, which provides high-level status information to the operation of the ALC, as well as detailed information for virtually all aspects of the ALC via drill-down displays. The operational status of an item, be it a function or assembly, is shown in the higher-level display. By pressing the item on the display screen, a new screen opens to show more detail of the function/assembly. Navigation tools and the map button allow immediate access to all screens.

Ahlstrom, Harlow↗
NASA NTRS1986

Plate motions and deformations from geologic and geodetic data

Research effort on behalf of the Crustal Dynamics Project focused on the development of methodologies suitable for the analysis of space-geodetic data sets for the estimation of crustal motions, in conjunction with results derived from land-based geodetic data, neo-tectonic studies, and other geophysical data. These methodologies were used to provide estimates of both global plate motions and intraplate deformation in the western U.S. Results from the satellite ranging experiment for the rate of change of the baseline length between San Diego and Quincy, California indicated that relative motion between the North American and Pacific plates over the course of the observing period during 1972 to 1982 were consistent with estimates calculated from geologic data averaged over the past few million years. This result, when combined with other kinematic constraints on western U.S. deformation derived from land-based geodesy, neo-tectonic studies, and other geophysical data, places limits on the possible extension of the Basin and Range province, and implies significant deformation is occurring west of the San Andreas fault. A new methodology was developed to analyze vector-position space-geodetic data to provide estimates of relative vector motions of the observing sites. The algorithm is suitable for the reduction of large, inhomogeneous data sets, and takes into account the full position covariances, errors due to poorly resolved Earth orientation parameters and vertical positions, and reduces baises due to inhomogeneous sampling of the data. This methodology was applied to the problem of estimating the rate-scaling parameter of a global plate tectonic model using satellite laser ranging observations over a five-year interval. The results indicate that the mean rate of global plate motions for that interval are consistent with those averaged over several million years, and are not consistent with quiescent or greatly accelerated plate motions. This methodology was also used to provide constraints on deformation in the western U.S. using very long baseline interferometry observations over a two-year period.

Jordan, T. H.↗
DOE OSTI2024

Performance evaluation of the USGS velocity model for the San Francisco Bay Area

In this study, we evaluated the performance of the United States Geological Survey velocity model developed for the San Francisco Bay Area (SFBA), version 21.1. The evaluation was performed through high-resolution three-dimensional physics-based ground motion simulations of seven small-magnitude earthquakes (ranging from magnitude 3.8 to 4.4) that occurred on the eastern side of the San Francisco Bay. The simulations were performed in the frequency range from 0 to 5 Hz with a minimum shear-wave velocity of 250 m/s, which allowed the capture of wave propagation effects of the near-surface soft materials that characterize local basins. Based on the direct comparison of Fourier amplitude spectra between recorded and simulated ground motions for more than 250 stations, we found that the velocity model generally performs well in the frequency range of 0.2–5 Hz. The median value of the Fourier amplitude residuals was found to be near zero for all seven earthquakes. The slight over-prediction of 0.2 log-natural units at frequencies above 3 Hz in our simulations was attributed to the potentially inaccurate representation of the source radiation pattern by a double-couple point source model, and simple representation of shallow small-scale underground structural complexity in the velocity model. Maps of spectral amplitude differences between the simulated and recorded data were used to identify areas responsible for systematic ground motion over-predictions or under-predictions. For example, while some sub-domains over soft sediments show over-prediction patterns, the block east of the Hayward fault is prone to exhibit patterns of under-prediction. These maps can be used to guide future refinements of the SFBA velocity model. Since our simulation methodology allows for the decoupling of the source and wave propagation effects, the ground motion data generated by our simulations can also be used to quantify the epistemic uncertainty due to the velocity model, in empirically based ground motion estimates for the SFBA.

58 GEOSCIENCES↗
NASA NTRS1977

Study of a close-grid geodynamic measurement system

The Clogeos (Close-Grid Geodynamic Measurement System) concept, a complete range or range-rate measurement terminal installed in a satellite in a near-polar orbit with a network of relatively simple transponders or retro-reflectors on the ground at intervals of 0.1 to 10 km was reviewed. The distortion of the grid was measured in three dimensions to accuracies of + or - 1 cm with important applications to geodynamics, glaciology, and geodesy. User requirements are considered, and a typical grid, designed for earthquake prediction, was laid out along the San Andreas, Hayward, and Calaceras faults in southern California. The sensitivity of both range and range-rate measurements to small grid motions was determined by a simplified model. Variables in the model are satellite altitude and elevation angle plus grid displacements in latitude, and height.

Source record↗
DOE OSTI2025

Tailoring mechanical properties of a multi-principal element alloy through a multi-length-scale approach

In this study, a multi-length-scale strengthening approach was used to tailor the microstructure and the mechanical properties of a NiCoCr-based multi-principal element alloy (MPEA). Grain size refinement, severe lattice distortion, and stacking fault energy (SFE) reduction with Mo addition (up to 10 at.%) enhance yield strength by 85% with only 10% reduction in ductility in as-annealed MPEAs. A pronounced increase in the strain hardening rate was observed with the addition of Mo, which is ascribed to the promotion of complex stacking fault (SF) interaction and intersection, accompanied by Lomer-Cottrell (L-C) and Hirth locks inhibiting dislocation motion and substantial increase in the accumulation of back stress. To push the limit of the yield strength further, the Suzuki segregation phenomenon was manipulated by a careful control of SF density by pre-straining and a subsequent 500 °C heat treatment. The stress-strain responses of the pre-strained and heat treated MPEAs showed an obvious SF density and Mo concentration dependence. Furthermore, the yield strength of the pre-strained Mo-added MPEAs with subsequent heat treatment was increased up to true stress of 2.3 GPa with a corresponding fracture elongation of 12% true strain. SFs formed during pre-straining served as Cr segregation sites during subsequent heat treatment, which substantially varies the local SFE within the SF, presenting a roughened landscape and frustrating the dislocation dynamics.

mechanical properties↗
DOE OSTI2024

Chemical randomness, lattice distortion and the wide distributions in the atomic level properties in high entropy alloys

High entropy alloys (HEAs) consist of multiple elements present in large proportions that are randomly distributed on a crystal lattice. On the one hand, the presence of multiple elements engenders wide ranges of atomic radii, electronegativities, electron valences and magnetic moments, whereas on the other, the presence of chemical randomness creates unique nearest neighbor environments among the lattice sites. As a result, the symmetry of the energy landscape is broken essentially at each lattice site thereby resulting in highly distorted energy landscapes. At the atomistic level, the lattice distortion has been widely observed in the form of varying bond lengths. At the electronic level, a range of charge transfers result in the charge density distortion. Collectively, the distorted landscapes cause large quantitative variations of the atomic level properties; in this review, we highlight the effect of lattice distortion on point defect energetics, stacking fault energies, and dislocation mobility. Besides the well- known large HEAs phase space, the enormity of the distorted energy landscape that scales with the atomic configurations is a new consideration; understanding this coupling between composition, lattice distortion and properties’ variations thus becomes an exciting but challenging area within the field of HEAs. Furthermore, this coupling is expected to open a new door for materials design, where the materials properties could be tuned via leveraging the lattice distortion, which is essentially absent in dilute/ordered alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

On various mechanisms of shear wave generation from underground chemical explosions in hard rocks

Significant shear waves observed during underground explosions can make them look similar to natural earthquakes. In the near field, they can be caused by the source geometry and emplacement conditions, heterogeneous and anisotropic properties of the rock mass, relaxation of a non-uniform in situ stress around the source after the departure of the shock wave as well as by activation of nearby faults. Here, the stress relaxation mechanism is important at depth when the difference in main principal stresses becomes significant. Another mechanism of shear motion generation is due to explosive gas flow from the source cavity into the cracks initiated by the shock wave and joints connected to the cavity. Also, the shock wave from the explosion can cause weakening of the rock either due to permanent damage or shock-induced liquefaction at saturated joints. Numerical modelling of underground chemical explosions in hard rock at various confinement stresses has been conducted to compare various mechanisms of shear wave generation and their seismic characteristics with that of a simple fault rupture process observed during an earthquake.

58 GEOSCIENCES↗
NASA NTRS1985

Transient polar motions and the nature of the asthenosphere for short time scales

A uniformly valid mathematical formalism is developed to study the secular motions of the rotational axis of a layered viscoelastic earth due to seismic excitation. The changes required for implementing the formulation within the framework of the faulting problem. The rationale of adopting the chosen nrheological model, which contains a low-viscosity zone beneath the lithosphere and is based on linear Maxell constitutive relationship, is discussed. The impact of this low-viscosity channel on thhe two families of relaxation time, governing both isostatic readjustment and rotational processes, is considered. It is found that the polar motions depend sensitively on the viscosity structure of the asthenosphere and not at all on the underlying mantle. A gloal low-velocity zone with short-term asthenospheric viscosities less than about 5 x 10 to the 18th Pa-s and widths greater than 50 km is ruled out.

Boschi, E.↗
NASA NTRS1984

Tectonic implications of the microearthquake seismicity and fault plane solutions in southern Peru

Because the contortion in the seismic zone in southern Peru is aligned approximately parallel to the direction of relative plate motion, rather than perpendicular to the coast of Peru, the position of the contortion need not migrate with respect to the overriding South American plate as the Nazca plate subducts beneath it, and the flow in the surrounding asthenosphere could be in a steady state. In addition, the position of the contortion defines the northern boundary of the volcanic arc in southern Peru. The inference that a wedge of asthenospheric material must overlie the downgoing slab for subduction-related volcanism to occur is thereby strengthened.

Grange, F.↗
DOE OSTI2021

Hypothesis tests on Rayleigh wave radiation pattern shapes: a theoretical assessment of idealized source screening

SUMMARY Shallow seismic sources excite Rayleigh wave ground motion with azimuthally dependent radiation patterns. We place binary hypothesis tests on theoretical models of such radiation patterns to screen cylindrically symmetric sources (like explosions) from non-symmetric sources (like non-vertical dip-slip or non-VDS faults). These models for data include sources with several unknown parameters, contaminated by Gaussian noise and embedded in a layered half-space. The generalized maximum likelihood ratio tests that we derive from these data models produce screening statistics and decision rules that depend on measured, noisy ground motion at discrete sensor locations. We explicitly quantify how the screening power of these statistics increase with the size of any dip-slip and strike-slip components of the source, relative to noise (faulting signal strength) and how they vary with network geometry. As applications of our theory, we apply these tests to (1) find optimal sensor locations that maximize the probability of screening non-circular radiation patterns and (2) invert for the largest non-VDS faulting signal that could be mistakenly attributed to an explosion with damage, at a particular attribution probability. Finally, we quantify how certain errors that are sourced by opening cracks increase screening rate errors. While such theoretical solutions are ideal and require future validation, they remain important in underground explosion monitoring scenarios because they provide fundamental physical limits on the discrimination power of tests that screen explosive from non-VDS faulting sources.

58 GEOSCIENCES↗
NASA NTRS1987

Flexurally-resisted uplift of the Tharsis Province, Mars

The tectonic style of Mars is dominated by vertical motion, perhaps more than any of the terrestrial planets. The imprint of this tectonic activity has left a surface widely faulted even though younger volcanism has masked the expression of tectonism in many places. Geological activity associated with the Tharsis and, to a lesser extent, Elysium provinces is responsible for a significant portion of this faulting, while the origins of the remaining features are enigmatic in many cases. The origin and evolution of the Tharsis and Elysium provinces, in terms of their great elevation, volcanic activity, and tectonic style, has sparked intense debate over the last fifteen years. Central to these discussions are the relative roles of structural uplift and volcanic construction in the creation of immense topographic relief. For example, it is argued that the presence of very old and cratered terrain high on the Tharsis rise, in the vicinity of Claritas Fossae, points to structural uplift of an ancient crust. Others have pointed out, however, that there is no reason that this terrain could not be of volcanic origin and thus part of the constructional mechanism.

Phillips, R. J.↗