Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fatigue loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A non-melting additive approach to structural repair of aluminum aircraft fastener holes

The damage to fastener holes in aerospace aluminum structures presents significant challenges for aircraft durability, and conventional bushing methods for repairing oversized holes often fall short due to the lack of metallurgical bonding and limited edge distance availability. This study investigates additive friction stir deposition, a non-melting additive process, as a viable alternative for the structural repair of aerospace fastener holes. The repair process, demonstrated on AA7050 (Al-Zn-Mg-Cu-Zr) hole structures, involves filling oversized holes with new material and machining to restore the original hole size. The repaired hole coupons are defect-free and exhibit good fatigue performance under fully reversed tension-compression loading (R = -1). At a nominal stress amplitude of 123.5 MPa, the average number of cycles to failure is 12,666 for unrepaired baseline coupons and 17,372 for effectively repaired coupons. Restoring complex geometries without compromising fatigue performance has been difficult in aerospace applications; this study marks the first demonstration of additive repair that consistently outperforms the unrepaired baseline coupons. Notably, the result is achieved through a low-energy, cost-effective solution without the need for post-repair heat treatment. Except for a few outliers, the post-repair fatigue performance generally remains inferior to that of undamaged, pristine coupons, likely due to precipitate evolution in AA7050 caused by the thermomechanical processing nature of additive friction stir deposition. This evolution weakens the repair region and the adjacent base material, leading to faster crack initiation and growth compared to the properly aged base material, AA7050-T7451.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Trunk muscle forces and spinal loads while walking in persons with lower limb amputation: Influences of chronic low back pain

Persons with lower limb amputation (LLA) are at high risk for developing chronic low back pain (LBP), often with biomechanical factors considered as likely contributors. Here, trunk and pelvis kinematics, muscle forces, and resultant spinal loads were characterized in persons with LLA, with and without chronic LBP. Thirty-five persons with unilateral LLA – 19 with chronic LBP (“LLA-cLBP”), 16 without LBP (“LLA-nLBP”) – and 15 (uninjured) persons without LBP (“CTR-nLBP”) walked overground (1.3 m/s) while thorax and pelvis kinematics were tracked (and ranges of motion [ROM] computed), and used as inputs for a non-linear finite element model of the spine to estimate global and local muscle forces, and resultant spinal loads. In the frontal and transverse planes, thorax ROM were up to 66.6% smaller in LLA-nLBP versus LLA-cLBP (P < 0.001) and CTR-nLBP (P < 0.001). In the sagittal plane, pelvis ROM was 50.4% smaller in LLA-nLBP versus LLA-cLBP (P = 0.014). LLA-cLBP exhibited 45.5% and 34.2% greater peak local and global muscle forces, respectively, versus CTR-nLBP (P < 0.011). Up to 48.1% greater spinal loads were observed in LLA-cLBP versus CTR-nLBP (P < 0.013); peak compression and local muscle forces were respectively 20.2% and 41.0% larger in LLA-nLBP versus CTR-nLBP (P < 0.005). Despite differences in trunk and pelvis kinematics between LLA-cLBP and LLA-nLBP, trunk muscle forces and spinal loads were similar (P > 0.101) between these groups. Similar loading parameters regardless of LBP presence, while highly dependent on trunk muscle activation strategies, may mitigate further accumulation of mechanical fatigue. Finally, it remains important to understand the temporality of loading with respect to LBP onset following LLA.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Microstructural Model for Creep-Fatigue Interaction in Grade 91 Steel

This report describes the completion of a crystal plasticity finite element simulation framework for creep-fatigue deformation and damage in Grade 91 steel. In addition to a description of the framework and a set of verification calculations, the report details an initial set of simulations applying the framework to examine low cycle fatigue and creep-fatigue interaction in Grade 91 at 600° C. Grade 91 is a likely material for future advanced microreactors and creep-fatigue will be a limiting structural damage mechanism, particularly for mobile reactors or load following systems. The framework described here could provide a better understanding of creep-fatigue damage mechanisms and directly examine creep, fatigue, and creep-fatigue interaction for Grade 91 at realistic component service conditions. This in turn could lead to improved design methods and component life estimation approaches, leading to more efficient and economical component designs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Initial Development of Variable Design Lifetimes and Creep-Fatigue Evaluations for ASME Section III, Division 5, Class B Code Rules

This report summarizes the initial development of new ASME Section III, Division 5, Class B rules to address the gaps identified for new high temperature reactor designs. The overall objective is to introduce the design-by-analysis approach, the variable design lifetimes for primary load design, and the strain limits and creep-fatigue damage evaluations for Class B components. It is also desired that the new evaluation procedures do not require stress classification and stress linearization. Further, the data requirements to support the development of design parameters for the new Class B rules would not be overly burdensome, and less extensive than those supporting Class A rules. We have identified the Elastic, Perfectly Plastic (EPP) method as the design by-analysis approach for primary load design, and developed allowable stress criteria for variable design lifetimes, up to 500,000 hours, that only require data typical for the allowable stresses in Section II, Part D, Tables 1A and 1B. We have also adapted the elastic analysis approach from HBB-T-1400 and Section III, Mandatory Appendix XIII, XIII-2400 and XIII-3520(e) for the new Class B creep-fatigue evaluation procedure. A new elastic follow-up-based Isochronous Stress Strain Curve (ISSC) stress relaxation procedure has been developed to provide adequate conservatism commensurate with Class B constructions. No stress classification and stress linearization are required in the new procedure. Future work needed to complete the development is also summarized.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Design by analysis rules for ASME Section III, Division 5, Class B components

The current rules for elevated temperature ASME Section III, Division 5, Class B components, other than piping, were basically adapted from the Design-by-Rule approach for Section VIII, Division 1 vessels. A goal of the proposed new rules is to explicitly account for the design life and cyclic service while recognizing the less-rigorous requirements commensurate with lesser safety consideration. Further goals are to maximize the use of modern computational technology, for example finite element analysis in conjunction with reference stress concepts, and to avoid the need for stress classification. This paper summarizes the work done to address these issues. A summary of the design-by-analysis for primary loads, strain limit evaluation, and creep-fatigue damage assessment is presented. The proposed design-by-analysis creep-fatigue damage calculation approach uses a new elastic follow-up-based Isochronous Stress Strain Curve stress relaxation procedure. A set of sample problems are selected to validate the proposed design-by-analysis rules for creep-fatigue damage assessment. The proposed Class B rules are evaluated against the Class A elastic design rules and the experimental data obtained from a family of a simplified model test-based key-feature test results. The proposed Class B creep-fatigue damage assessment methodology yields conservative design cycles estimates compared to the experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Final Scientific/Technical Report-FREE-piston Zero Emissions Refrigerator (FREEZER)

The FREE-piston Zero Emissions Refrigerator (FREEZER™) is a natural refrigerant Stirling-cycle cooler developed by AMSC in partnership with Heatcraft, targeted as a replacement refrigeration system for walk-in coolers or freezers found commonly in restaurants, convenience stores, supermarkets, etc. The FREEZER™, combined with a closed-loop CO2 heat-transfer system, had the goal to provides an efficient (Target COP = 1.4), zero ODP (Ozone Depletion Potential) and near zero GWP (Global Warming Potential) refrigeration solution with no synthetic, flammable, or toxic refrigerants. Other near zero GWP refrigeration systems do not exist at the scale and performance level of FREEZER. ARPA-E Continuation Funding enabled the design and fabrication of one Advanced Development Unit (ADU) cooler and two Field Test Unit (FTU) coolers, and a new revised Field Test Unit (new FTU). Heatcraft was to extensively test the various coolers at their facilities, which closely simulate real-world conditions. The original plan was to install and operate FREEZER FTUs alongside a traditional cooling solution at one or more customer locations to obtain data on direct performance comparisons with existing commercial refrigeration systems. Success in this FREEZER refinement and field-test project will establish the basis for a new class of environmentally friendly refrigeration systems that will revolutionize the industry. The hardware developed under the program is shown below in Figure 1. Five Stirling-cycle machines were built within the program, with a sixth cooler still under construction. The original DU and the ADU coolers met the performance target with a coefficient of performance (COP) of 1.2. The FTU was underperforming during the initial tuning of the free-piston Stirling cycle dynamics when there was a catastrophic failure of the fasteners on pressure boundary. This caused a pause to the program while the failure mechanism was investigated. The root cause was an inadequate flange design that allowed an excessive cyclic loading on the fasteners, leading to a fatigue failure. It was determined that existing FTU design could not be reasonably salvaged in a safe manner, and that fact, combined with the lower-than-expected performance of the new experimental heat exchanger modules lead to the design of the “new FTU” with a more conventional shell-and-tube heat exchanger design which should get close to the design target COP of 1.4, but have a higher overall machine cost. The program ran out of time before the fabrication of the new FTU was completed, but AMSC is still working on the cooler, with the majority of the parts fabricated, and hopes to have the unit under test sometime in early 2022, after which it will be shipped to Heatcraft for additional testing.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

A Combined Computational and Mathematical Analysis of Interconnect Fatigue Potential in Photovoltaic Modules

A finite element model of a 60-cell monocrystalline silicon glass-polymer photovoltaic module was simulated with ±1.0 kPa and ±2.4 kPa loads applied to the glass to calculate the deformation under load. Cell-to-cell displacements were used to approximate interconnect strain and stress. A mathematical fatigue cycle life relation was fitted to data for the interconnect material (copper), to generate a life prediction at each interconnect location based on the local stress means, reversal extents, and amplitudes. Interconnect stress was found to be significantly asymmetric about zero despite symmetric positive and negative module loads due to laminate thickness offsets about the neutral plane and the effects of module framing. Cycle life results indicated that interconnect fatigue failure was unlikely to occur over a 30-year lifetime of conservative wind and snow load cycles since the typical cell design feature of leaving some unconstrained length between the cell edge and first solder pad increases the effective gauge length and decreases the stress levels below the material endurance limit. Follow-up analyses found that 3.6 mm and 6.4 mm were the minimum unconstrained lengths required to survive the assumed lifetime of wind and snow cycles, respectively, confirming that typical industrial module constructions with 8–15 mm unconstrained lengths should survive conservatively. Notably, large magnitude, low-cycle snow loading was consistently the limiting factor requiring a longer unconstrained interconnect length. Finally, insights and workflows from this study inform module interconnection design limits for survival against mechanical fatigue in deployment environments.

14 SOLAR ENERGY↗
DOE OSTI2026

Gigacycle Fatigue Strength Evaluation of Welded 316L Stainless Steels for Mercury Target Vessel

At the Materials and Life Science Experimental Facility (MLF) in J-PARC, liquid mercury target for the pulsed spallation neutron source is in operation. An enclosure vessel for the liquid mercury target made of type 316L stainless steel (SS316L) suffers two kinds of cyclic stress during operation. One is the thermal stress due to the internal heating and swings by proton beam trip. The other is the impulsive stress by the pressure waves generated by the proton beam injection. The total number of loading cycles for the former is ∼104, and the latter is ∼4 × 108 for a year operation in the J-PARC mercury target vessel. The target vessel is assembled by an electron beam welding (EBW) and a gas tungsten arc welding (GTAW). However, fatigue data of welded SS316L up to gigacycle is limited. Ultrasonic fatigue testing, applying load cycles by utilizing ultrasonic resonance, for the welded SS316L was performed to investigate the effect of welding on fatigue behavior up to a gigacycle. The result showed that the fatigue strength degradation by EBW and EBW with GTAW were not recognized up to 109 cycles. Crack initiation in welded specimens nucliated at off-center areas of the specimen whereas the cracks in base metal specimen originated at the specimen center.

Naoe, Takashi [Japan Atomic Energy Agency (JAEA)]↗
DOE OSTI2020

In situ indentation and high cycle tapping deformation responses in a nanolaminate crystalline/amorphous metal composite

The incorporation of nanostructured and amorphous metals into modern applications is reliant on the understanding of deformation and failure modes in constrained conditions. To study this, a 105 nm crystalline Cu/160 nm amorphous Cu 45 Zr 55 (at.%) multilayer structure was fabricated with the two crystalline layers sputter deposited between the top-middle-bottom amorphous layers and prepared to electron transparency. The multilayer was then in situ indented either under a single load to a depth of ~ 100 nm (max load of ~ 100 μN) or held at 20 μN and then repeatedly indented with an additional 5 μN up to 20,000 cycles in a transmission electron microscope to compare the deformation responses in the nanolaminate. For the single indentation test, the multilayer showed serrated load-displacement behavior upon initial indentation inductive of shear banding. Additionally, at an indentation depth of ~ 32 nm, the multilayer exhibited perfect plastic behavior and no strain hardening. Both indented and fatigue-indented films revealed diffraction contrast changes with deformation. Subsequent Automated Crystal Orientation Mapping (ACOM) measurements confirmed and quantified global texture changes in the crystalline layers with specifically identified grains revealing rotation. Using a finite element model, the in-plane displacement vectors under the indent mapped conditions where ACOM determined grain rotation was observed, indicating the stress flow induced grain rotation. Furthermore, the single indented Cu layers also exhibited evidence of deformation induced grain growth, which was not evident in the fatigue-indented Cu based multilayer. Finally, the single indented multilayer retained a significant plastic crater in the upper most amorphous layer that directly contacted the indenter; a negligible crater impression in the same region was observed in the fatigued tested multilayer. These differences are explained by the different loading methods, applied load, and deformation mechanisms experienced in the multilayers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ monitoring of dislocation, twinning, and detwinning modes in an extruded magnesium alloy under cyclic loading conditions

This work investigates the microscopic deformation mechanisms of an extruded, precipitation-strengthened AZ80 magnesium (Mg) alloy subjected to strain-controlled low-cycle fatigue using in situ neutron diffraction measurements. Results demonstrate that the plastic deformation during cyclic loading is dominated by the alternating {10.2} extension twinning and detwinning mechanisms. The observed deformation mode is strongly texture and precipitate dependent. For the initial texture, the tested material has two major texture components which result in the occurrence of extension twinning during both compression and reverse tension in the first two cycles. The prolonged detwinning process in the following cycles is proposed to relieve the shear stress field of {00.2} grains, leading to the disappearance of twinning. The precipitation strengthening results in an increase of the critical resolved shear stress (CRSS) by similar to 33 MPa for the extension twinning in this AZ80 alloy. Here, the synergistic effects of the initial texture, precipitation strengthening, and load sharing of various grain families and phases contribute to the complicated evolution of dominant deformation mechanisms, among which elevated dislocation activities are believed to be responsible for the relatively poor low-cycle-fatigue lifetime when compared to other Mg alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A review of the fabrication methods and mechanical behavior of continuous thermoplastic polymer fiber–thermoplastic polymer matrix composites

Abstract Thermoplastic polymer fiber–thermoplastic polymer matrix composites (PPCs or PRFPs), often recognized as self‐reinforced or single polymer composites, are potential candidates for future advanced polymer composites because of various advantages ( e.g., recyclability, formability, low‐cost, ultra‐lightweight, environmental friendliness, etc.). The manufacturability and mechanical behavior of these composites compared to conventional carbon‐/glass‐/aramid‐fiber‐reinforced polymers is of great interest to the composites community, but there are a limited number of studies in this area. To this end, this paper reviewed fabrication methods with different processing parameters and mechanical behavior of uni‐/multi‐directional thermoplastic PPCs featuring continuous thermoplastic polymer fibers from limited data in the literature. It was shown that most specific behaviors (normalized by density) of these materials in various loading conditions (e.g., quasi‐static tension/shear/flexure, tension‐tension fatigue, and out‐of‐plane impacting, etc.) are comparable to or better than glass‐/aramid‐fiber‐reinforced polymers. Particularly, the specific ductility in the foregoing conditions outperforms all the carbon‐/glass‐/aramid‐fiber‐reinforced polymers. Thermoplastic PPCs with remarkable performance can be achieved through several uncomplicated methods (e.g., film stacking, hot compaction, powder and solution impregnations, matrix infusion and injection molding, additive manufacturing, etc.), which have some similarities to the methods used for carbon‐/glass‐/aramid‐fiber‐reinforced polymers. Moreover, several opportunities and challenging problems of thermoplastic PPCs were summarized at the end of this review paper. Efficient solutions may require countless efforts in the composites community to further strengthen the performance and understanding of thermoplastic PPCs for wide applications in various engineering fields in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The effect of stretching on polyamide – 6: assessment of crystallinity, mechanical properties, and surface roughness

Polyamide-6 (PA6), or nylon-6, is a widely used low-cost polymer material for various applications. Manufacturing PA6 into fibers involves a spinning process such as melt extrusion, which orients the polymer chains into a semicrystalline structure. When stretching the produced fibers to high strains, the PA6 fibers transition the metastable gamma phase back into the stable gamma phase. The effects of these large stretches on mechanical properties have not been explored after the stretch has been released. In this study, the effects on mechanical properties were studied by stretching the PA6 fibers from 10% to 50% tensile strain and subsequently releasing the fibers. The stretched fibers were characterized by X-ray diffraction and atomic force microscopy to determine the changes to the crystal structure and surface roughness. The stretched fibers were then tensile tested to failure and the tensile properties were examined. The stress-strain curves on the post-stretched PA6 fibers showed clear softening in the fibers with lower initial moduli after 30% stretching. Furthermore, these results may hold a clue to softening of fibers in applications with repeated loading and have implications for mechanical stability and fatigue of this polymeric material.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Build orientation, surface roughness, and scan path influence on the microstructure, mechanical properties, and flexural fatigue behavior of Ti–6Al–4V fabricated by electron beam melting

In the present work, microstructure and fatigue behavior of Electron Beam Melted (EBM) Ti–6Al–4V have been systematically studied. Fatigue behavior was investigated using four-point bend tests of rectangular bars with internal features fabricated with different build orientations, scan paths, and surface conditions. Microstructural variations were evaluated by optical microscopy and Vickers micro-hardness indentations, both of which were found to be consistent throughout the build and within ranges reported in the literature. The fatigue performance of the EBM material was comparable to wrought Ti–6Al–4V when the loading direction was parallel to the build direction, but severely limited when loaded perpendicular to the build direction or if surface roughness defects were present. Scanning electron microscopy and interrupted fatigue tests were utilized to characterize fracture surfaces, failure mechanisms, crack initiation, and propagation behavior. Crack initiation sites in the vertically-oriented specimens were identified to be melt-related defects formed by insufficient melting.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Update on the Current R&D Activity in the U.S.

This presentation is to fulfil DOE commitment to GIF VHTR Materials PMB. Notched creep rupture testing: Weldment V-notch specimen test finished. 800C 60MPa, 15,716 hour rupture life. Two double V-notch specimen tests have finished. Crack growth tests: System modification was required for creep and creep-fatigue testing, Epsilon 3548COD Extensometer has been ordered, to allow load-line displacement measurements, to be paired with direct current potential drop already used to measure crack length, Sample redesigned in accordance to ASTM E2760 and E1457 to allow for both creep and creep-fatigue crack growth rate testing. Alloy 800H Weldments (1/2) and Alloy 800H Weldments (2/2), Variable Fatigue Testing, and Multi=axial Stress Relaxation. Continue work to finish 800H model, examine ?universal? constitutive model form.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Environmentally Assisted Fatigue in Light Water Reactor Environment

This report summarizes the Environmentally Assisted Fatigue (EAF) research conducted at ANL under the US DOE Light Water Reactor Sustainability (LWRS) program. Starting from a rich background in theoretical and experimental EAF, ANL previously developed an approach to evaluate fatigue performance of reactor materials in light water reactor environments with the correction factor F en . The approach was based on a large body of experimental work performed at ANL and elsewhere, and was consistent with American Society of Mechanical Engineers (ASME)’s methodology governing the design and construction of reactor components. In recent years, the program was focused on component fatigue prediction and made several major and fundamental contributions in this area. These accomplishments help meet the needs identified by the industry concerning component level fatigue predictions in complex, transient conditions. The main contribution of the ANL program involved the development of a system-level model for estimating residual strain and life of nuclear reactor coolant system components under connected-system-thermal-mechanical boundary conditions. The goal was to predict the stress hotspots, strain residuals, strain amplitudes and the resulting fatigue lives. Thermal-mechanical stress analysis was performed considering thermal stratification and a design-basis reactor loading cycle. Based on the finite element (FE) model results, the strain residuals, strain amplitudes and resulting fatigue lives of reactor coolant system (RCS) components were predicted. The results show that some of the RCS components can have significantly different strain amplitudes, residual strain, and fatigue lives, despite having similar geometry and material. In addition, the simulated component-level strain profile can guide the selection of appropriate test inputs for conducting laboratory-scale EAF tests. Building upon the system-level model, ANL developed a digital twin (DT) framework to predict the structural states and associated fatigue life of components in real-time. This framework is a comprehensive system designed to predict the structural states and fatigue lives of reactor components. It includes multiple models and integrates artificial intelligence (AI), machine learning (ML), and FE based modeling tools to evaluate the structural states and fatigue lives.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Offshore Wind Turbine Blade (85 to120meters ultra-long blade) static and fatigue test

Offshore blades are not just longer, they are wider, heavier and more flexible. These longer blades are a key component of larger wind turbines and for turbines to be more efficient in low wind speeds. These longer blades help reduce the LCOE further and make offshore wind even more competitive. As described earlier, it is essential for the blades to be fully tested to verify and validate the blade designs and manufacturing processes to ensure a reliable product is installed in the field. Through this project WTTC developed and procured new testing equipment required to test longer blades with larger deflections and higher loads. R&D’s BCDA system commissioned was the largest fatigue test exciter system in the world and set the bar for other blade testing facilities worldwide.

17 WIND ENERGY↗
DOE OSTI2022

Land-based wind turbines with flexible rail-transportable blades – Part 2: 3D finite element design optimization of the rotor blades

Abstract. Increasing growth in land-based wind turbine blades to enable higher machine capacities and capacity factors is creating challenges in design, manufacturing, logistics, and operation. Enabling further blade growth will require technology innovation. An emerging solution to overcome logistics constraints is to segment the blades spanwise and chordwise, which is effective, but the additional field-assembled joints result in added mass and loads, as well as increased reliability concerns in operation. An alternative to this methodology is to design slender flexible blades that can be shipped on rail lines by flexing during transport. However, the increased flexibility is challenging to accommodate with a typical glass-fiber, upwind design. In a two-part paper series, several design options are evaluated to enable slender flexible blades: downwind machines, optimized carbon fiber, and active aerodynamic controls. Part 1 presents the system-level optimization of the rotor variants as compared to conventional and segmented baselines, with a low-fidelity representation of the blades. The present work, Part 2, supplements the system-level optimization in Part 1 with high-fidelity blade structural optimization to ensure that the designs are at feasible optima with respect to material strength and fatigue limits, as well as global stability and structural dynamics constraints. To accommodate the requirements of the design process, a new version of the Numerical Manufacturing And Design (NuMAD) code has been developed and released. The code now supports laminate-level blade optimization and an interface to the International Energy Agency Wind Task 37 blade ontology. Transporting long, flexible blades via controlled flapwise bending is found to be a viable approach for blades of up to 100 m. The results confirm that blade mass can be substantially reduced by going either to a downwind design or to a highly coned and tilted upwind design. A discussion of active and inactive constraints consisting of material rupture, fatigue damage, buckling, deflection, and resonant frequencies is presented. An analysis of driving load cases revealed that the downwind designs are dominated by loads from sudden, abrupt events like gusts rather than fatigue. Finally, an analysis of carbon fiber spar caps for downwind machines finds that, compared to typical carbon fibers, the use of a new heavy-tow carbon fiber in the spar caps is found to yield between 9 % and 13 % cost savings.

17 WIND ENERGY↗
DOE OSTI2023

The effect of current and lambda on white-etch-crack failures

White etching cracks (WECs) have been associated with premature failure of wind turbine roller bearings. Various drivers for the generation of WECs have been identified such as loading conditions, slip, steel quality, lubrication, hydrogen embrittlement, corrosion fatigue cracking, and stray electrical currents passing through the surface. Here, in this work, a benchtop test rig utilizing a three-ring-on-roller test configuration was used to investigate the effect of electrical current and operation in different lubricating regimes, defined by lambda (λ), on high-quality bearing steel samples tested in a commercially available power transmission EP gear lubricant. It was observed that there is an inverse correlation between the magnitude of electric current applied to the ring/ roller system and time-to-failure. Higher current magnitudes lead to shorter time-to-failure than lower current magnitudes, with macropitting as the main failure mode. Sub-surface investigation revealed the presence of WECs in all cases. For the same current magnitude, tests conducted in boundary and mixed lubrication regimes showed that time-to-failure increased as lambda increased, and the tests resulted in WEC related macropits, whereas tests conducted in near-hydrodynamic regime resulted in surface damage with no macropit. It was also noted that a shift toward near-hydrodynamic lubrication resulted in a distinct surface distress on the roller surface. Furthermore, there seems to be a transition in the mixed regime during which the surface distress occurred. The damage on the surface of the test samples resembled non-spatially, periodic, groove-like corrugations and, in some cases, crater-like depressions. Sub-surface imaging, performed by sequential sectioning, revealed the presence of WECs in all cases, and broad, branching cracks that were more prevalent under the more severe boundary conditions.

17 WIND ENERGY↗