Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “diffusion barrier”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Photoemission from cesium-oxide-activated InGaAsP.

Zinc-doped InGaAsP quaternary III-V material of the proper composition range shows superior photoemission properties to either InGaAs or InAsP ternary material. The minority-carrier diffusion length in the quaternary material is at least as long as that in InAsP and much longer than observed in InGaAs. The barrier height at the InGaAsP-Cs2O interface is lowered by cooling, giving increased electron escape probability and new highs in quantum efficiency over a wide wavelength range. For example, a 1.06-micron quantum efficiency of 7.5%/incident photon was observed at -90 C.

James, L. W.↗
NASA NTRS1978

Development of Low Cost Contacts to Silicon Solar Cells

Commercial electroless Cu solutions were used. Satisfactory adhesion (and fairly good cell performance) resulted from the use of thin layers of barrier metals such as Au, Cr or Pd. In these tests, photoresist masks were used to contact silicon P-type slices with diffused N+ and alloyed P+ surfaces; and electrolytic Cu solution was used to build up the contact thickness to provide good cell behavior. In addition some cells with evaporated Cr-Cu contacts were also made (along with evaporated Ti-Pd-Ag contacts as controls), with the intention of subjecting cells to gradually increasing heat-treatments, to determine whether Cu causes the cells to be inherently unstable.

Iles, P. A.↗
NASA NTRS1992

Study of the oxygen transport through Ag (110), Ag (poly), and Ag 2.0 Zr

The transport of oxygen through high-purity membranes of Ag (110), Ag (poly), Ag (nano), and Ag 2.0 Zr has been studied by an ultrahigh vacuum permeation method over the temperature range of 400-800 C. The data show that there are substantial deviations from ordinary diffusion-controlled transport. A surface limitation has been confirmed by glow-discharge studies where the upstream O2 supply has been partially converted to atoms, which, for the same temperature and pressure, gave rise to over an order of magnitude increase in transport flux. Further, the addition of 2.0 wt percent Zr to the Ag has provided increased dissociative adsorption rates, which, in turn, increased the transport flux by a factor of 2. It was also observed that below a temperature of 630 C, the diffusivity exhibits an increase in activation energy of over 4 kcal/mol, which has been attributed to trapping of the atomic oxygen and/or kinetic barriers at the surface and subsurface of the vacuum interface. Above 630 C, the activation barrier decreases to the accepted value of about 11 kcal/mol for Ag (poly), consistent with zero concentration at the vacuum interface.

Outlaw, R. A.↗
NASA NTRS2010

Operational Considerations for Oxygen Flammability Risks: Concentrated Oxygen Diffusion and Permeation Behaviors

Increased human spaceflight operations utilize oxygen concentrations that are frequently varied with use of concentrations up to 100 percent oxygen. Even after exiting a higher percentage oxygen environment, high oxygen concentrations can still be maintained due to material saturation and oxygen entrapment between barrier materials. This paper examines the material flammability concerns that arise from changing oxygen environments during spaceflight operations. We examine the time required for common spacecraft and spacesuit materials exposed to oxygen to return to reduced ignitability and flammability once removed from the increased concentration. Various common spacecraft materials were considered: spacecraft cabin environment foams, Extra Vehicular Mobility Unit materials and foams, Advanced Crew Escape Suit materials, and other materials of interest such as Cotton, Nomex^ HT90-40, and Tiburon Surgical Drape. This paper presents calculated diffusion coefficients derived from experimentally obtained oxygen transmission rates for the tested materials and the analytically derived times necessary for reduced flammability to be achieved based on NASA flammability criteria. Oxygen material saturation and entrapment scenarios are examined. Experimental verification data on oxygen diffusion in saturation scenarios are also presented and discussed. We examine how to use obtained data to address flammability concerns during operational planning to reduce the likelihood of fires while improving efficiency for procedures.

Harper, Susana↗
NASA NTRS1998

Transport Between the Tropical and Midlatitude Lower Stratosphere: Implications for Ozone Response to High Speed Civil Transport Emissions

Several recent studies have quantified the air exchange rate between the tropics and midlatitudes in the lower stratosphere using airborne and satellite measurements of chemical species. It is found that the midlatitude air is mixed into the tropical lower stratosphere with a replacement timescale of 13.5 months (with 20% uncertainty) for the region from the tropopause to 21 km and at least 18 months for the region of 20-28 km. These estimates are used to adjust the horizontal eddy diffusion coefficients, K(sub yy), in a two-dimensional chemistry transport model. The value of K(sub yy) previously used to simulate the subtropical barrier, 0.03 x 10(exp 6)sq m/s, generates an exchange time of about 4 years, and the model without subtropical barrier (K(sub yy) = 0.3 x 10(exp 6)sq m/s) has an exchange time of 5 months. Adjusting the K(sub yy) to 0.13 x 10(exp 6) sq m/s from the tropopause to 21 km and 0.07 x 10(exp 6)sq m/s above 21 km produces the exchange timescales which match the estimates deduced from the measurements. The subtropical barrier prevents the engine emissions of the high-speed civil transport (HSCT) aircraft from being transported into the tropics and subsequently lifted into the upper atmosphere or mixed into the southern hemisphere. The model results show that the calculated ozone response to HSCT aircraft emissions using the K(sub yy), adjusted to observed mixing rates is substantially smaller than that simulated without the subtropical barrier.

Shia, R.-L.↗
NASA NTRS1998

Transport Between the Tropical and Midlatitude Lower Statosphere: Implications for Ozone Response to High-Speed Civil Transport Emissions

Several recent studies have quantified the air exchange rate between the tropics and midlatitudes in the lower stratosphere using airborne and satellite measurements of chemical species. It is found that the midlatitude air is mixed into the tropical lower stratosphere with a replacement timescale of 13.5 months (with 20% uncertainty) for the region from the tropopause to 21 km and at least 18 months for the region of 20-28 km. These estimates are used to adjust the horizontal eddy diffusion coefficients, K(sub yy), in a two-dimensional chemistry transport model. The value of K(sub yy) previously used to simulate the subtropical barrier, 0.03 x 10(exp 6) sq m/s, generates an exchange time of about 4 years, and the model without subtropical barrier (K(sub yy) = 0.3 x 10(exp 6) sq m/s) has an exchange time of 5 months. Adjusting the K(sub yy) to 0.13 x 10(exp 6) sq m/s from the tropopause to 21 km and 0.07 x 10(exp 6) sq m/s above 21 km produces the exchange timescales which match the estimates deduced from the measurements. The subtropical barrier prevents the engine emissions of the high-speed civil transport (HSCT) aircraft from being transported into the tropics and subsequently lifted into the upper atmosphere or mixed into the southern hemisphere. The model results show that the calculated ozone response to HSCT aircraft emissions using the K(sob yy) adjusted to observed mixing rates is substantially smaller than that simulated without the subtropical barrier.

Shia, R.-L.↗
NASA NTRS1995

Theoretical Study of Response of InGaAs Metal-Semiconductor-Metal Photodetectors

We present a theoretical investigation of the response of metal-semiconductor-metal (MSM) photodetectors made of InGaAs lattice-matched to InP using a two-dimensional drift-diffusion model with a thermionic-field emission boundary condition for the heterojunctions. The effect of including a top InAlAs layer to increase the effective barrier height of the metal fingers on the InGaAs active layer is thoroughly examined and found to limit the collection of the photocurrent signal due to the electron and hole barriers that it forms with InGaAs. Due to the thickness and height of the InAlAs barrier layer in existing designs, the tunneling current obtained from the model is found to be negligibly small to significantly affect the output signal current. In an attempt to obtain a better response, different design structures including one where a quasi-Schottky contact is utilized are studied and their speed of response, breakdown voltage, and dark current are compared to that of the usual InGaAs device.

Salem, Ali F.↗
NASA NTRS1992

Venus internal magnetic field and its interaction with the interplanetary magnetic field

In a previous study, Knudsen et al. suggested that Venus has a weak internal magnetic dipole field of the order of 7 x 10 + 20 G cm(exp -3) that is manifested in the form of magnetic flux tubes threading the ionospheric holes in the Venus nightside ionosphere. They pointed out that any internal field of Venus, dipole or multipole, would be weakened in the subsolar region and concentrated in the antisolar region of the planet by the supersonic transterminator convection of the dayside ionosphere into the nightside hemisphere. The inferred magnitude of the dipole field does not violate the upper limit for an internal magnetic field established by the Pioneer Venus magnetometer experiment. The most compelling objection to the model suggested by Knudsen et al. has been the fact that it does not explain the observed interplanetary magnetic field (IMF) control of the polarity of the ionospheric hole flux tubes. In this presentation I suggest that a magnetic reconnection process analogous to that occurring at earth is occurring at Venus between the IMF and a weak internal dipole field. At Venus in the subsolar region, the reconnection occurs within the ionosphere. At Earth it occurs at the magnetopause. Reconnection will occur only when the IMF has an appropriate orientation relative to that of the weak internal field. Thus, reconnection provides a process for the IMF to control the flux tube polarity. The reconnection in the subsolar region takes place in the ionosphere as the barrier magnetic field is transported downward into the lower ionosphere by downward convection of ionospheric plasma and approaches the oppositely directed internal magnetic field that is diffusing upward. The reconnected flux tubes are then transported anti-Sunward by the anti-Sunward convecting ionospheric plasma as well as by the anti-Sunward-flowing solar wind. Reconnection will also occur in the Venus magnetic tail region, somewhat analogously to the reconnection that occurs in the magnetotail of the Earth. The possibility that reconnection is occurring between the IMF and an internal dipole field may be tested by measuring the orientation of the IMF projected into a plane perpendicular to the solar wind velocity during time intervals for which ionospheric holes are observed. The orientations of the IMV components should fall within a 180 deg angle.

Knudsen, W. C.↗
NASA NTRS2013

Calcium-Magnesium-Aluminosilicate (CMAS) Reactions and Degradation Mechanisms of Advanced Environmental Barrier Coatings

The thermochemical reactions between calcium-magnesium-aluminosilicate- (CMAS-) based road sand and several advanced turbine engine environmental barrier coating (EBC) materials were studied. The phase stability, reaction kinetics and degradation mechanisms of rare earth (RE)-silicates Yb2SiO5, Y2Si2O7, and RE-oxide doped HfO2 and ZrO2 under the CMAS infiltration condition at 1500 C were investigated, and the microstructure and phase characteristics of CMAS-EBC specimens were examined using Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Experimental results showed that the CMAS dissolved RE-silicates to form crystalline, highly non-stoichiometric apatite phases, and in particular attacking the silicate grain boundaries. Cross-section images show that the CMAS reacted with specimens and deeply penetrated into the EBC grain boundaries and formed extensive low-melting eutectic phases, causing grain boundary recession with increasing testing time in the silicate materials. The preliminary results also showed that CMAS reactions also formed low melting grain boundary phases in the higher concentration RE-oxide doped HfO2 systems. The effect of the test temperature on CMAS reactions of the EBC materials will also be discussed. The faster diffusion exhibited by apatite and RE-doped oxide phases and the formation of extensive grain boundary low-melting phases may limit the CMAS resistance of some of the environmental barrier coatings at high temperatures.

Ahlborg, Nadia L.↗
NASA NTRS1991

Surface effects on hydrogen permeation through Ti-14Al-21Nb alloy

Hydrogen transport through Ti-14Al-21Nb (wt percent) alloy is measured using ultrahigh vacuum permeation techniques over the temperature range of 500 to 900 C and hydrogen pressure range of 0.25 to 10 torr. Hydrogen permeability through the alloy can be described through two different mechanisms depending on th temperature of exposure. In the 675 to 900 C range, the process is diffusion-limited: the permeability has a weak temperature dependence, but the diffusivity has a strong temperature dependence. Below 675 C, the permeation rate of hydrogen is very sensitive to surface controlled processes such as the formation of a barrier layer from contaminants. A physical model explaining the role of surface films on the transport of hydrogen through Ti-14Al-21Nb alloy was described.

Sankaran, Sandara N.↗
NASA NTRS2004

Kinetic Roughening Transition and Energetics of Tetragonal Lysozyme Crystal Growth

Interpretation of lysozyme crystal growth rates using well-established physical theories enabled the discovery of a phenomenon possibly indicative of kinetic roughening. For example, lysozyme crystals grown above a critical supersaturation sigma, (where supersaturation sigma = ln c/c(sub eq), c = the protein concentration and c(sub eq) = the solubility concentration) exhibit microscopically rough surfaces due to the continuous addition of growth units anywhere on the surface of a crystal. The rate of crystal growth, V(sub c), for the continuous growth process is determined by the continuous flux of macromolecules onto a unit area of the crystal surface, a, from a distance, xi, per unit time due to diffusion, and a probability of attachment onto the crystal surface, expressed. Based upon models applied, the energetics of lysozyme crystal growth was determined. The magnitudes of the energy barriers of crystal growth for both the (110) and (101) faces of tetragonal lysozyme crystals are compared. Finally, evidence supportive of the kinetic roughening hypothesis is presented.

Gorti, Sridhar↗
NASA NTRS2013

Wear and Reactivity Studies of Melt infiltrated Ceramic Matrix Composite

As interest grows in the use of ceramic matrix composites (CMCs) for critical gas turbine engine components, the effects of the CMCs interaction with the adjoining structure needs to be understood. A series of CMC/material couples were wear tested in a custom elevated temperature test rig and tested as diffusion couples, to identify interactions. Specifically, melt infiltrated silicon carbide/silicon carbide (MI SiC/SiC) CMC was tested in combination with a nickel-based super alloy, Waspaloy, a thermal barrier coating, Yttria Stabilized Zirconia (YSZ), and a monolithic ceramic, silicon nitride (Si3N4). To make the tests more representative of actual hardware, the surface of the CMC was kept in the as-received state (not machined) with the full surface features/roughness present. Test results include: scanning electron microscope characterization of the surfaces, micro-structural characterization, and microprobe analysis.

Jarmon, David C.↗
NASA NTRS1975

Studies on the Al2O3-Ti-Mo-Au metallization system

The behavior of Ti-Mo-Au metallization on Al2O3 and C has been investigated by backscattering spectrometry. Results show that Mo-Au bimetal films typically mix during deposition. Diffusion of Ti in Mo film occurs at 600 C, but is inhibited by the presence of oxygen in the Ti film. Even 1000 A of Mo is not a barrier against interdiffusion of Ti and Au during 20-min anneals at 600 C. The amount of mixing observed also depends on the nature of the substrate which supports the Ti-Mo-Au metallization.

Harris, J. M.↗
NASA NTRS1981

Creep of oxide dispersion strengthened materials /with special reference to T-D nichrome/

Analyses of oxide dispersion strengthened (ODS) alloys shows that their characteristics are mainly due to the creep behavior of the matrix material. Diffusion-controlled slip creep is established as the rate-controlling process in the alloys investigated, with the glide and climb of edge dislocations associated with the subgrain structure as barriers being the specific rate-controlling step. It is found that the stable subgrain size in ODS alloys is usually associated with the spacing between particles 500-1000 A in size, and that their creep behavior is distinguished from that of the matrix material by the existence of a threshold stress that is not well defined microscopically but appears to be related to particles of less than 500 A size.

Lin, J.↗
NASA NTRS2005

NASA Tech Briefs, September 2005

Topivs include: Diamond-Coated Carbon Nanotubes for Efficient Field Emission; Improved Anode Coatings for Direct Methanol Fuel Cells; Advanced Ablative Insulators and Methods of Making Them; PETIs as High-Temperature Resin-Transfer-Molding Materials; Stable Polyimides for Terrestrial and Space Uses; Low-Density, Aerogel-Filled Thermal-Insulation Tiles; High-Performance Polymers Having Low Melt Viscosities; Nonflammable, Hydrophobic Aerogel Composites for Insulation; Front-Side Microstrip Line Feeding a Raised Antenna Patch; Medium-Frequency Pseudonoise Georadar; Facilitating Navigation Through Large Archives; Program for Weibull Analysis of Fatigue Data; Comprehensive Micromechanics-Analysis Code - Version 4.0; Component-Based Visualization System; Software for Engineering Simulations of a Spacecraft; LabVIEW Interface for PCI-SpaceWire Interface Card; Path Following with Slip Compensation for a Mars Rover; International Space Station Electric Power System Performance Code-SPACE; Software for Automation of Real-Time Agents, Version 2; Software for Optimizing Plans Involving Interdependent Goals; Computing Gravitational Fields of Finite-Sized Bodies; Custom Sky-Image Mosaics from NASA's Information Power Grid; ANTLR Tree Grammar Generator and Extensions; Generic Kalman Filter Software; Alignment Stage for a Cryogenic Dilatometer; Rugged Iris Mechanism; Treatments To Produce Stabilized Aluminum Mirrors for Cryogenic Uses; Making AlNx Tunnel Barriers Using a Low-Energy Nitrogen-Ion Beam; Making Wide-IF SIS Mixers with Suspended Metal-Beam Leads; Sol-Gel Glass Holographic Light-Shaping Diffusers; Automated Counting of Particles To Quantify Cleanliness; Phase Correction for GPS Antenna with Nonunique Phase Center; Compact Infrasonic Windscreen; Broadband External-Cavity Diode Laser; High-Efficiency Solar Cells Using Photonic-Bandgap Materials; Generating Solid Models from Topographical Data; Computationally Lightweight Air-Traffic-Control Simulation; Spool Valve for Switching Air Flows Between Two Beds; Partial Model of Insulator/ Insulator Contact Charging; Asymmetric Electrostatic Radiation Shielding for Spacecraft; and Reusable Hybrid Propellant Modules for Outer-Space Transport.

Source record↗
NASA NTRS2017

High Efficiency Centrifugal Compressor for Rotorcraft Applications

A centrifugal compressor research effort conducted by United Technologies Research Center under NASA Research Announcement NNC08CB03C is documented. The objectives were to identify key technical barriers to advancing the aerodynamic performance of high-efficiency, high work factor, compact centrifugal compressor aft-stages for turboshaft engines; to acquire measurements needed to overcome the technical barriers and inform future designs; to design, fabricate, and test a new research compressor in which to acquire the requisite flow field data. A new High-Efficiency Centrifugal Compressor stage -- splittered impeller, splittered diffuser, 90 degree bend, and exit guide vanes -- with aerodynamically aggressive performance and configuration (compactness) goals were designed, fabricated, and subquently tested at the NASA Glenn Research Center.

Centrifugal compressor↗
NASA NTRS2015

A Semianalytical Ocean Color Inversion Algorithm with Explicit Water Column Depth and Substrate Reflectance Parameterization

A semianalytical ocean color inversion algorithm was developed for improving retrievals of inherent optical properties (IOPs) in optically shallow waters. In clear, geometrically shallow waters, light reflected off the seafloor can contribute to the water-leaving radiance signal. This can have a confounding effect on ocean color algorithms developed for optically deep waters, leading to an overestimation of IOPs. The algorithm described here, the Shallow Water Inversion Model (SWIM), uses pre-existing knowledge of bathymetry and benthic substrate brightness to account for optically shallow effects. SWIM was incorporated into the NASA Ocean Biology Processing Group's L2GEN code and tested in waters of the Great Barrier Reef, Australia, using the Moderate Resolution Imaging Spectroradiometer (MODIS) Aqua time series (2002-2013). SWIM-derived values of the total non-water absorption coefficient at 443 nm, at(443), the particulate backscattering coefficient at 443 nm, bbp(443), and the diffuse attenuation coefficient at 488 nm, Kd(488), were compared with values derived using the Generalized Inherent Optical Properties algorithm (GIOP) and the Quasi-Analytical Algorithm (QAA). The results indicated that in clear, optically shallow waters SWIM-derived values of at(443), bbp(443), and Kd(443) were realistically lower than values derived using GIOP and QAA, in agreement with radiative transfer modeling. This signified that the benthic reflectance correction was performing as expected. However, in more optically complex waters, SWIM had difficulty converging to a solution, a likely consequence of internal IOP parameterizations. Whilst a comprehensive study of the SWIM algorithm's behavior was conducted, further work is needed to validate the algorithm using in situ data.

Great Barrier Reef↗