Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dielectric accelerator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

197 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Passivated Contacts for Direct Wafer Product (Final Technical Report)

This TCF project developed a thin-oxide (SiO 2 )/polycrystalline silicon (poly-Si) passivated contact solar cell on CubicPV's (formally 1366 Technologies, Inc.) Direct Wafer® Product (DWP) kerfless wafers. The project used two NREL-developed technologies described in U.S. Patent No. 9,911,873, Hydrogenation of Passivated Contacts and U.S. Patent Application Serial No. 15/890,172, Doped Passivated Contacts . The project was motivated by a potential higher efficiency cell (compared to a PERC cell) using passivated contacts on the ultra-low cost kerfless wafers grown using the Direct Wafer process. The hope was to accelerate market adoption of the cell and wafer by delivering the lowest LCOE in the PV industry. The project tested both n-type and p-type SiO 2 /poly-Si passivated contacts grown by thermal oxidation and plasma enhanced chemical vapor deposition (PECVD) of the poly-Si layer on DWP with varying wafer resistivities. Both deposition techniques are industry standards and thus economically viable methods for commercializing the contacts. The results indicated that both n-type and p-type poly-Si passivated contacts can be formed on polycrystalline DWP wafers, but implied open-circuit voltages (i Voc ) were limited to below 0.65 mV (compared with ~ 730 mV on n-Cz wafers). Diffusion of H to the Si/SiO 2 /poly-Si interface was key to obtaining high i Voc values. In this study, H was diffused from a high-temperature SiN x layer deposited over the poly-Si layer during a high-temperature firing step, similar to one used for screen printed metals. The study concluded that poly-Si passivated contacts on DWP wafers passivated the surface of the wafers as well as PERC passivated surfaces, which use a less expensive dielectric layer stack. The project showed that Direct Wafer Product wafers grown by CubicPV could produce high i Voc values (~0.647 mV), which could produce a cell over 20% efficient with proper processing and metallization. These cells, though not economically viable in 2024 as a stand-alone cell, could be integrated with a wide-bandgap top solar cell to form a two-junction tandem cell that could be viable under certain circumstances. This is because the bottom cell of a 30%, two-terminal tandem only needs to be a 20% cell under one-sun conditions. Thus, the DWP could be an ideal low-cost wafer for tandems. The project also revealed that a TOPCon type cell could be formed on a p-type DWP wafer using a P-diffused emitter and a p-type poly-Si contact. In fact, the p-type version of the poly-Si contact out-performed the n-type version for a variety of wafer resistivities, from highly doped to lowly doped. This curiosity requires more work to understand because on Cz wafers, the n-type poly-Si contact is of much higher quality than the p-type version.

14 SOLAR ENERGY↗
DOE OSTI2022

Molecular-scale mechanisms of CO 2 mineralization in nanoscale interfacial water films

The calamitous impacts of untethered carbon emission from fossil-fuel-burning energy infrastructure calls for accelerated development of large-scale CO 2 capture, utilization, and storage technologies that are underpinned by fundamental understanding of molecular-level chemical processes. In the subsurface, rocks rich in divalent metals can react with CO 2 , permanently sequestering it in the form of stable metal carbonate minerals, with the CO 2 -H 2 O composition of the post-injection pore fluid acting as a primary control variable. Herein, we compare mechanistic reaction pathways for aqueous-mediated carbonation with carbon mineralization occurring in nanoscale adsorbed water films. In the extreme of pores filled with a CO 2 -dominant fluid, carbonation reactions are confined to nanometer-thick water films coating mineral surfaces, which enable metal cation release, transport, nucleation, and crystallization of metal carbonate minerals. Though seemingly counterintuitive, laboratory studies have demonstrated facile carbonation rates in these low water environments, which in recent years has begun to be better understood in mechanistic detail. The overarching objective of this review is to delineate the unique underlying molecular-scale reaction mechanisms that govern CO 2 mineralization in these reactive and dynamic quasi-2D interfaces. Here. we highlight the importance of understanding unique properties in thin water films, such as how water dielectric properties, and consequently ion solvation/hydration behavior, can change under nanoconfinement. We conclude by identifying important frontiers for future work and opportunities to exploit these fundamental chemical insights for decarbonization technologies in the 21st century.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

An SF 6 gas-insulated −500 kV DC conical insulator vacuum feedthrough

A test electrode was biased to −500 kV direct current (DC) by means of a novel SF 6 gas-insulated conical alumina insulator feedthrough. The design enables the extreme high vacuum conditions required by spin-polarized electron sources by reducing the photogun vacuum chamber volume compared to coaxial cylindrical insulators. In contrast to conventional inverted-insulator photogun designs that rely on solid dielectric interfaces for high-voltage terminations, the present design employs a pressurized SF 6 intervening volume between a conical alumina insulator and a modified commercial epoxy high-voltage cable receptacle. Here, this approach enables the use of commercially available cable hardware while extending the demonstrated operating voltage of solid feedthroughs. A maximum voltage of −500 kV was applied to a test electrode attached to the narrow end of the feedthrough inside a chamber filled with SF 6 at 170.3 kPa (10 psig) and later under vacuum to −259 kV, limited by field emission. The results demonstrate that a commercial high-voltage cable combined with a custom-designed SF 6 gas-insulated vacuum feedthrough can be used to bias photogun electrodes to −500 kV DC.

Palacios-Serrano, Gabriel [Thomas Jefferson Nation↗
DOE OSTI2025

Generation of fast photoelectrons in strong-field emission from metal nanoparticles

We investigated the generation and control of fast photoelectrons (PEs) by exposing plasmonic nanoparticles (NPs) to short infrared (IR) laser pulses with peak intensities between 10 12 and 3 × 10 13 W/cm 2 . Our measured and numerically simulated PE momentum distributions demonstrate the extent to which PE yields and cutoff energies are controlled by the NP size, material, and laser peak intensity. For strong-field photoemission from spherical silver, gold, and platinum NPs with diameters between 10 and 100 nm our results confirm and surpass extremely high PEs cutoff energies, up to several hundred times the incident laser-pulse ponderomotive energy, found recently for gold nanospheres [Saydanzad et al., Nanophotonics 12, 1931 (2023)]. As reported previously for dielectric NPs [Rupp et al., J. Mod. Opt. 64, 995 (2017)], at higher intensities the cutoff energies we deduce from measured and simulated PE spectra tend to converge to a metal-independent limit. We expect these characteristics of light-induced electron emission from prototypical plasmonic metallic nanospheres to promote the understanding of the electronic dynamics in more complex plasmonic nanostructures and the design of nanoscale light-controlled plasmonic electron sources for photoelectronic devices of applied interest.

electron source↗
DOE OSTI2024

Decomposition characteristics of C4F7N-based SF6-alternative gas mixtures

C4F7N [2,3,3,3-tetrafluoro-2-(trifluoromethyl)propanenitrile]/CO2 gas mixtures are being developed as an eco-friendly electrical insulator to replace SF6, the most potent greenhouse industrial gaseous dielectric. However, recent studies have reported complicated and often conflicting decomposition pathways for C4F7N/CO2 gas mixtures, which has raised concerns. In this work, the decomposition characteristics of C4F7N/CO2 gas mixtures were studied comprehensively by both designed computations and experiments. Computations were performed starting from fundamental propositions of C4F7N/CO2 decompositions, which were further experimentally verified by pyrolysis, long-term thermal aging with/without catalytic materials (industrial-grade molecular sieves 4A), and electrical decomposition by spark discharge. The results of both computations and experiments suggest that in an ideal thermal decomposition, C4F7N is likely to decompose into C2F6 and small fluoronitriles first at high temperatures. The generation of C3F6 and C2N2 from C4F7N thermal decomposition at lower temperatures appears because of the catalytic effect of incompatible materials, for example, the industrial-grade molecular sieves 4A that we tested. The electron impact dissociation of C4F7N plays an important role in C4F7N electrical decomposition, leading to additional formation of distinctive small molecules of CF4 and C2N2 of low concentrations. It was pointed out based on a real arcing test in a load disconnector that the decomposition of C4F7N gas mixtures in real applications will be at a much moderate and manageable rate than what was obtained from the highly accelerated laboratory tests presented in this work. The signatures of decomposition products extracted in this study provide invaluable guidance for developing decomposition-based diagnosis and fixation of decomposition byproducts toward SF6-free power grids.

Physics↗
NASA NTRSDate not supplied

Microbial Vessel for Impedance Spectroscopy and Electrochemistry (Mvise): an Extensible, Interoperable Data Acquisition Platform for Liquid Culture Studies in Space Biology Research

The White House Office of Science and Technology Policy (OSTP) has declared 2023 to be the Year of Open Science following an initiative to democratize scientific knowledge. Simultaneously, new sensor technologies have broadened the experimental space available to bioastronautics research. With these open-science goals and technological advances in mind, we have designed and constructed a data acquisition platform for high-precision, real-time monitoring of liquid culture systems. The vessel rig is fitted with six Atlas Scientific probes (micro pH, electrical conductivity, dissolved oxygen, oxidation-reduction potential, liquid temperature, air CO2) and a custom optical density probe similar to the one on BioSentinel’s BioSensor payload. A custom dielectric spectroscopy probe is also planned. The structure of the vessel is resin 3-D printed on a hobbyist-level machine, reducing the production cost and iteration time by over 60% each while increasing extensibility. Data acquisition and storage is controlled with a standalone C state machine-based program running on a Raspberry Pi 3 Model B. When not running headless, an additional program automatically generates and updates plots for live data visualization. Validation of the rig as a data collection system was performed with a yeast liquid culture experiment. While the vessel rig is currently used for standalone experiments, it can also be used as the base perception unit in a self-driving laboratory (SDL). SDLs are high-throughput data collection systems that employ automation and artificial intelligence to conduct and manage routine experiments. Here, we envision an SDL driven by several vessel rigs in which an automated script compares key results, informing the design of future experiments. A vessel rig SDL would streamline many operations, including 1) strain selection for the Lunar Explorer Instrument for space biology Applications (LEIA) investigation and 2) the study of bioregenerative life support systems (BLSS). Ultimately, the datasets that can now be acquired will provide crucial information for accelerating bioastronautics application development in the era of commercial space.

Stephen Lantin↗
DOE OSTI2025

Machine learning enhanced predictions of ICRF heating: Overcoming numerical limitations via data curation

In this work, we present the development of robust surrogate models for Ion Cyclotron Range of Frequencies (ICRF) and High-Harmonic Fast Wave (HHFW) heating predictions in fusion plasmas. Building upon our previous efforts to achieve real-time capable models, we identify the cause of the outliers found using TORIC in certain HHFW heating scenarios. The outliers are observed to be spurious ion Bernstein wave (IBW)-like modes caused by a wavelength control algorithm designed to address challenging scenarios with high perpendicular wavenumbers. The effect arises from the modulation in the perpendicular susceptibility, which can induce sign reversal and IBW-like propagation for scenarios featuring normalized ion Larmor radius λ i ≫ 1. We use TORIC with this algorithm disabled to generate a novel HHFW-NSTX database that is free of outliers. Surrogate models trained on this database, including Random Forest Regressor (RFR), Multi-Layer Perceptrons, and Gaussian Process Regressors (GPR), demonstrate the ability to accurately predict HHFW heating profiles, with regression scores of R 2 ∈[0.93−0.99]. Additionally we demonstrate that it is possible to generalize predictions beyond training data by the use of both RFR and GPR models, enabling the prediction of scenarios previously limited to the original model. GPR models also provide uncertainty quantification, offering insights into model confidence. This work introduces a comprehensive Verification, Validation, and Uncertainty Quantification methodology for surrogate modeling, applicable not only to ICRF heating but also to other RF heating challenges and fusion physics problems. Beyond accelerated inference, these models show effective extrapolation capabilities, providing an alternative for addressing numerical challenges.

Artificial neural networks↗
DOE OSTI2021

Effect of metamaterial engineering on the superconductive properties of ultrathin layers of NbTiN

The electronic transport and optical properties of high quality multilayers of NbTiN/AlN with ultrathin NbTiN layers were characterized. The anisotropy of the dielectric function of the multilayers confirmed their hyperbolic metamaterial properties. Here, the superconductive transition temperature, T c , of these engineered superconductors was enhanced up to 32% compared to the T c of a single ultrathin NbTiN layer while the resistivity per NbTiN layer remained unchanged. We have demonstrated that this T c increase can be attributed to enhanced electron–electron interaction in superconducting hyperbolic metamaterials. The measured critical fields are high and have an anomalous temperature dependence on the direction perpendicular to the magnetic field. These results demonstrate that the metamaterial engineering approach can be used to enhance H c2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Microwave-assisted pyrolysis of liquid hydrocarbons using iron-based alumina catalysts obtained by solution combustion synthesis: The effect of synthesis parameters

The microwave-absorbing and catalytic properties of iron-based alumina (FeAl x O y ) materials have enabled their use as catalysts for the microwave-assisted generation of hydrogen and carbon via pyrolysis of hydrocarbons. Solution combustion synthesis (SCS) is a promising method to fabricate these materials, but the pyrolysis performance still needs to be improved. The present work investigated how altering the SCS parameters affects the pyrolysis of diesel fuel, gasoline, and crude oil. Two fuels (citric acid and glycine), four Fe:Al molar ratios, and two heating modes (hotplate and furnace) were tested. Fe/γ-Al 2 O 3 and Fe/β-SiC catalysts were prepared via incipient wetness impregnation for comparison. Among the three fossil fuels tested, diesel fuel yielded the highest amounts of H 2 and least amounts of CO x . The choice of fuel for the SCS process and the Fe/Al ratio strongly affected pyrolysis performance as they influence properties important for both catalysis and microwave absorption. The use of glycine resulted in catalysts that exhibited high H 2 yield and low CO 2 generation, which is explained by the revealed structural differences. The increase in the Fe:Al molar ratio accelerated microwave heating by adding more magnetic loss but also increased the amount of CO x . When the optimal SCS parameters were used, FeAl x O y catalysts outperformed Fe/γ-Al 2 O 3 and Fe/β-SiC. The high H 2 generation efficiency of the SCS catalysts is explained by their enhanced microwave-absorption properties. Scanning electron microscopy and energy dispersive X-ray spectroscopy revealed the formation of large-diameter CNTs via the tip-growth mechanism. The regeneration of SCS catalysts was demonstrated via the Boudouard reaction.

Carbon nanotubes↗
DOE OSTI2025

Light field–controlled PHz currents in intrinsic metals

Oriented electric currents in metals are routinely driven by applying an external electric potential. Although the response of electrons to the external electric fields occurs within attoseconds, conventional electronics do not use this speed potential. Ultrashort laser pulses with controlled shapes of electric fields that switch direction at petahertz frequencies open perspectives for driving currents in metals. Light field–driven currents were demonstrated in various media including dielectrics, semiconductors, and topological insulators. Now, our research question is whether we can drive and control orders of magnitude more charge carriers in metals enabling ultrafast switching with practically low-energy, picojoule-level pulses. Here, we demonstrate the interaction of light with nanometer-thick metallic layers, which leads to a generation of light field–controlled electric currents. We show that the implantation of metallic layers into a dielectric matrix leads to up to 40 times increase of the sensitivity in contrast to a bare dielectric, decreasing the intensity threshold for lightwave electronics.

Fehér, Beatrix [HUN-REN Wigner Research Centre for↗
DOE OSTI2021

Stray-Capacitance As a Simple Tool for Monitoring and Locating Heat Generation Demonstrated in Three Superconducting Magnets

Real-time monitoring of heat loads in cryogenic systems is critical for many applications, particularly high field magnets. In this work, we demonstrated that by monitoring changes in the capacitance of local probes consisting of thin metal strips with a porous glass fiber dielectric, boiling helium from as little as 0.1 J of deposited heat can be located by an analysis of the response speed and amplitude in nearby probes. We further implemented stray-capacitance monitoring of a magnet's metal support structures, a more global probe of the magnet volumes, in three high temperature superconducting Bi-2212 magnet types. Global structural stray-capacitance monitoring was evaluated for a single racetrack coil, a common coil dipole, and a canted cosine theta winding, showing a quench response comparable to voltage signals without inductive effects. The response of the local and global probes was compared in the single racetrack coil with well-known quench properties. Monitoring the cool-down of the common coil dipole demonstrated the added benefit of the global stray-capacitance as a liquid level monitor. This simple method of monitoring the capacitance has proven to be a versatile and robust technique for monitoring and locating heat.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Crowd-Sourced Data and Analysis Tools for Advancing the Chemical Vapor Deposition of Graphene: Implications for Manufacturing

Industrial production of graphene by chemical vapor deposition (CVD) requires more than the ability to synthesize large domain, high-quality graphene in a lab reactor. The integration of graphene in the fabrication process of electronic devices requires the cost-effective and environmentally friendly production of graphene on dielectric substrates, but current approaches can only produce graphene on metal catalysts. Sustainable manufacturing of graphene should also conserve the catalyst and reaction gases, but today the metal catalysts are typically dissolved after synthesis. Progress toward these objectives is hindered by the hundreds of coupled synthesis parameters that can strongly affect CVD of low-dimensional materials and poor communication in the published literature of the rich experimental data that exists in individual laboratories. We report here on a platform, "graphene recipes for synthesis of high quality material" (Gr-ResQ: pronounced graphene rescue), which includes powerful new tools for data-driven graphene synthesis. At the core of Gr-ResQ is a crowd-sourced database of CVD synthesis recipes and associated experimental results. The database captures similar to 300 parameters ranging from synthesis conditions such as a catalyst material and preparation steps, to ambient lab temperature and reactor details, as well as resulting Raman spectra and microscopy images. These parameters are carefully selected to unlock the potential of machine-learning models to advance synthesis. A suite of associated tools enable fast, automated, and standardized processing of Raman spectra and scanning electron microscopy images. To facilitate community-based efforts, Gr-ResQ provides tools for cyber-physical collaborations among research groups, allowing experiments to be designed, executed, and analyzed by different teams. Gr-ResQ also allows publication and discovery of recipes via the Materials Data Facility, which assigns each recipe a unique identifier when published and collects parameters in a search index. We envision that this holistic approach to data-driven synthesis can accelerate CVD recipe discovery and production control and open opportunities for advancing not only graphene but also many other 1D and 2D materials.

36 MATERIALS SCIENCE↗
NASA NTRS2011

Effect of Reverse Bias Stress on Leakage Currents and Breakdown Voltages of Solid Tantalum Capacitors

The majority of solid tantalum capacitors are produced by high-temperature sintering of a fine tantalum powder around a tantalum wire followed by electrolytic anodization that forms a thin amorphous Ta2O5 dielectric layer and pyrolysis of manganese nitrite on the oxide to create a conductive manganese dioxide electrode. A contact to tantalum wire is used as anode terminal and to the manganese layer as a cathode terminal of the device. This process results in formation of an asymmetric Ta -- Ta2O5 -- MnO2 capacitor that has different characteristics at forward (positive bias applied to tantalum) and reverse (positive bias applied to manganese cathode) voltages. Reverse bias currents might be several orders of magnitude larger than forward leakage currents so I-V characteristics of tantalum capacitors resemble characteristics of semiconductor rectifiers. Asymmetric I-V characteristics of Ta -- anodic Ta2O5 systems have been observed at different top electrode materials including metals, electrolytes, conductive polymers, and manganese oxide thus indicating that this phenomenon is likely related to the specifics of the Ta -- Ta2O5 interface. There have been multiple attempts to explain rectifying characteristics of capacitors employing anodic tantalum pentoxide dielectrics. A brief review of works related to reverse bias (RB) behavior of tantalum capacitors shows that the mechanism of conduction in Ta -- Ta2O5 systems is still not clear and more testing and analysis is necessary to understand the processes involved. If tantalum capacitors behave just as rectifiers, then the assessment of the safe reverse bias operating conditions would be a relatively simple task. Unfortunately, these parts can degrade with time under reverse bias significantly, and this further complicates analysis of the I-V characteristics and establishing safe operating areas of the parts. On other hand, time dependence of reverse currents might provide additional information for investigation of the processes under reverse bias conditions. In practice, there were instances when, due to unforeseen events, the system operated at conditions when capacitors experience periodically a relatively small reverse bias for some time followed by normal, forward bias conditions. In such a case an assessment should be made on the degree to which these capacitors are degraded by application of low-voltage reverse bias, and whether this degradation can be reversed by normal operating conditions. In this study, reverse currents in different types of tantalum capacitors were monitored at different reverse voltages below 15%VR and temperatures in the range from room to 145 C for up to 150 hours to get better understanding of the degradation process and determine conditions favorable to the unstable mode of operation. The reversibility of RB degradation has been evaluated after operation of the capacitors at forward bias conditions. The effect of reverse bias stress (RBS) on reliability at normal operating conditions was evaluated using highly accelerated life testing at voltages of 1.5VR and 2 VR and by analysis of changes in distributions of breakdown voltages. Possible mechanisms of RB degradation are discussed.

Teverovsky, Alexander A.↗
NASA NTRS2015

Insulation Resistance Degradation in Ni-BaTiO3 Multilayer Ceramic Capacitors

Insulation resistance (IR) degradation in NiBaTiO3 multilayer ceramic capacitors has been characterized by the measurement of both time to failure (TTF) and direct current leakage current as a function of stress time under highly accelerated life test conditions. The measured leakage current time dependence data fit well to an exponential form, and a characteristic growth time tau (sub SD) can be determined. A greater value of tau (sub SD) represents a slower IR degradation process. Oxygen vacancy migration and localization at the grain boundary region results in the reduction of the Schottky barrier height and has been found to be the main reason for IR degradation in NiBaTiO3 capacitors. The reduction of barrier height as a function oftime follows an exponential relation of phi (t ) = phi (0) e (exp -2Kt), where 13 the degradation rate constant K Koe (Ek/kT) is inversely proportional to the mean TTF (MTTF) and can be determined using an Arrhenius plot. For oxygen vacancy electromigration, a lower barrier height phi (0) will favor a slow IR degradation process, but a lower phi (0) will also promote electronic carrier conduction across the barrier and decrease the IR. As a result, a moderate barrier height phi (0) (and therefore a moderate IR value) with a longer MTTF (smaller degradation rate constant K) will result in a minimized IR degradation process and the most improved reliability in NiBaTiO3 multilayer ceramic capacitors.

reliability↗
NASA NTRS2015

Insulation Resistance Degradation in Ni-BaTiO3 Multilayer Ceramic Capacitors

Insulation resistance (IR) degradation in Ni-BaTiO3 multilayer ceramic capacitors has been characterized by the measurement of both time to failure and direct-current (DC) leakage current as a function of stress time under highly accelerated life test conditions. The measured leakage current-time dependence data fit well to an exponential form, and a characteristic growth time SD can be determined. A greater value of tau(sub SD) represents a slower IR degradation process. Oxygen vacancy migration and localization at the grain boundary region results in the reduction of the Schottky barrier height and has been found to be the main reason for IR degradation in Ni-BaTiO3 capacitors. The reduction of barrier height as a function of time follows an exponential relation of phi (𝑡)=phi (0)e(exp -2Κt), where the degradation rate constant 𝐾=𝐾o𝑒(𝐸𝑘/𝑘𝑇) is inversely proportional to the mean time to failure (MTTF) and can be determined using an Arrhenius plot. For oxygen vacancy electromigration, a lower barrier height phi(0) will favor a slow IR degradation process, but a lower phi(0) will also promote electronic carrier conduction across the barrier and decrease the insulation resistance. As a result, a moderate barrier height phi(0) (and therefore a moderate IR value) with a longer MTTF (smaller degradation rate constant 𝐾) will result in a minimized IR degradation process and the most improved reliability in Ni-BaTiO3 multilayer ceramic capacitors.

dielectric degradation↗
DOE OSTI2026

Microwave Vortex Motion Characterization of Nb$_{3}$ Sn Coatings for Applications in High Magnetic Fields

In this work, microwave measurements carried out in dielectric-loaded resonators exposed to high magnetic fields are exploited to yield the surface impedance of Nb$_3$ Sn superconducting coatings deposited via two different techniques: vapor tin diffusion, and DC magnetron sputtering. The obtained data lead to qualitative interpretations on both the Nb$_3$ Sn superconducting properties, and vortex-dynamics and pinning, of each coating separately, as well as simple distinctive features when comparing those. When examining the respective surface impedances at varying field, it is expected that the studied films perform at substantially diverse magnitudes of flux-flow resistivity, but also in well-differentiated pinning regimes, yet the obtained surface resistances of both samples are comparable, thus demonstrating that there is room for film optimization at the expense of certain compromise between the parameters involved.

Nb3Sn↗
DOE OSTI2026

Decoding THz‐Driven Dynamic Fingerprints of Ferroelectric Nanotwin Networks

Ultrafast polarization dynamics in ferroelectrics are of considerable interest for high-speed tunable dielectrics and electro-optics. Extended domain wall networks formed in ferroelectric twin nanodomains can support collective dynamics in the terahertz regime but require techniques that track polarization and strain evolution driven by ultrafast stimulus. Here, we use multi-modal probing of THz-pulse-driven excitations in PbTiO 3 /SrTiO 3 superlattices by combining X-ray free electron laser measurements that directly tracks lattice changes, with optical second harmonic generation that tracks the electronic potential coupled with the lattice potential. Dynamical phase-field modeling enables fingerprinting of these collective modes as superpositions of domain “breathing” through wall oscillations and polarization “rotations” with still walls. Ultrafast domain wall motion at 0.1–0.5 THz is observed at practical fields of 100 kV/cm with wall velocities of >4000 m/s, approaching typical speed of sound in PbTiO 3 . A unique “charging” mode is discovered that can electrically charge and discharge domain walls on ∼4 ps time scale thus dynamically tuning wall conductivity. Integrated experimental and theoretical fingerprinting of the dynamical landscape presented here enables ultrafast control of ferroics for high-speed microelectronics and optical applications.

THz dynamics↗