Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “deflection equations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Optimal recovery from microburst wind shear

The flight path of a twin-jet transport aircraft is optimized in a microburst encounter during approach to landing. The objective is to execute an escape maneuver that maintains safe ground clearance and an adequate stall margin during the climb-out portion of the trajectory. A cost function penalizing rate of climb deviations from a nominal value and rate of elevator deflection produces qualitatively good results in a variety of microburst encounters. The optimal maneuver is a gradual pitch-up that ceases near the core of the microburst, followed by a slight reduction in pitch attitude in the tailwind area of the microburst. A minimum airspeed constraint in the optimization prevents excessive airspeed loss in very severe microbursts. The aircraft equations of motion include short-period dynamics, so that the optimization solves directly for the control surface deflections required to achieve the optimal flight paths.

Mulgund, Sandeep S.↗
NASA NTRS1985

On the impact of initially stressed composite laminates

The impact response behavior of initially stressed composite laminates is investigated using the finite element method. An experimentally established contact law is incorporated into the finite element program. The Newmark time integration algorithm is used for solving the time dependent equations of the plate and the impactor. Numerical results, including the contact force history, deflection, and strain in the plate, are presented. Effects of impact velocity, initial stress, and the mass and size of the impactor are discussed.

Sun, C. T.↗
NASA NTRS1976

Out of ecliptic missions using Venus or earth gravity assists

Multiple Venus or earth gravity-assist flybys are investigated as a means of producing trajectories that are inclined to the solar equator at low cost in total delta V. There are three phases to such trajectories: (1) production of a high flyby speed at the planet encounter, (2) attainment of one-to-one resonance by orbit pumping, and (3) deflection to high inclination by orbit cranking. Flybys are restricted to occur at the node of the planet orbit and the solar equator so as to take advantage of the natural inclination of the solar equator. For Venus flybys, the high approach speed is inherent in the earth to Venus trajectory. For earth flybys, the production of high approach speed can be accomplished by a VEGA (Venus-earth-gravity assist) trajectory or by a delta V-EGA trajectory. The general result is that moderate inclinations to the solar equator can be obtained at moderate total delta V cost, but at flight times which rise to five years for an inclination of 37 deg and to 13 years for an inclination of 54 deg.

Bender, D. F.↗
NASA NTRS2016

Unsteady Aerodynamic Force Sensing from Measured Strain

A simple approach for computing unsteady aerodynamic forces from simulated measured strain data is proposed in this study. First, the deflection and slope of the structure are computed from the unsteady strain using the two-step approach. Velocities and accelerations of the structure are computed using the autoregressive moving average model, on-line parameter estimator, low-pass filter, and a least-squares curve fitting method together with analytical derivatives with respect to time. Finally, aerodynamic forces over the wing are computed using modal aerodynamic influence coefficient matrices, a rational function approximation, and a time-marching algorithm. A cantilevered rectangular wing built and tested at the NASA Langley Research Center (Hampton, Virginia, USA) in 1959 is used to validate the simple approach. Unsteady aerodynamic forces as well as wing deflections, velocities, accelerations, and strains are computed using the CFL3D computational fluid dynamics (CFD) code and an MSC/NASTRAN code (MSC Software Corporation, Newport Beach, California, USA), and these CFL3D-based results are assumed as measured quantities. Based on the measured strains, wing deflections, velocities, accelerations, and aerodynamic forces are computed using the proposed approach. These computed deflections, velocities, accelerations, and unsteady aerodynamic forces are compared with the CFL3D/NASTRAN-based results. In general, computed aerodynamic forces based on the lifting surface theory in subsonic speeds are in good agreement with the target aerodynamic forces generated using CFL3D code with the Euler equation. Excellent aeroelastic responses are obtained even with unsteady strain data under the signal to noise ratio of -9.8dB. The deflections, velocities, and accelerations at each sensor location are independent of structural and aerodynamic models. Therefore, the distributed strain data together with the current proposed approaches can be used as distributed deflection, velocity, and acceleration sensors. This research demonstrates the feasibility of obtaining induced drag and lift forces through the use of distributed sensor technology with measured strain data. An active induced drag control system thus can be designed using the two computed aerodynamic forces, induced drag and lift, to improve the fuel efficiency of an aircraft. Interpolation elements between structural finite element grids and the CFD grids and centroids are successfully incorporated with the unsteady aeroelastic computation scheme. The most critical technology for the success of the proposed approach is the robust on-line parameter estimator, since the least-squares curve fitting method depends heavily on aeroelastic system frequencies and damping factors.

shape sensing↗
NASA NTRS2015

Strain Gage Loads Calibration Testing with Airbag Support for the Gulfstream III SubsoniC Research Aircraft Testbed (SCRAT)

This paper describes the design and conduct of the strain-gage load calibration ground test of the SubsoniC Research Aircraft Testbed, Gulfstream III aircraft, and the subsequent data analysis and results. The goal of this effort was to create and validate multi-gage load equations for shear force, bending moment, and torque for two wing measurement stations. For some of the testing the aircraft was supported by three airbags in order to isolate the wing structure from extraneous load inputs through the main landing gear. Thirty-two strain gage bridges were installed on the left wing. Hydraulic loads were applied to the wing lower surface through a total of 16 load zones. Some dead-weight load cases were applied to the upper wing surface using shot bags. Maximum applied loads reached 54,000 lb. Twenty-six load cases were applied with the aircraft resting on its landing gear, and 16 load cases were performed with the aircraft supported by the nose gear and three airbags around the center of gravity. Maximum wing tip deflection reached 17 inches. An assortment of 2, 3, 4, and 5 strain-gage load equations were derived and evaluated against independent check cases. The better load equations had root mean square errors less than 1 percent. Test techniques and lessons learned are discussed.

flight tests↗
NASA NTRS1972

Random deflections of a string on an elastic foundation.

The paper is concerned with the problem of a taut string on a random elastic foundation subjected to random loads. The boundary value problem is transformed into an initial value problem by the method of invariant imbedding. Fokker-Planck equations for the random initial value problem are formulated and solved in some special cases. The analysis leads to a complete characterization of the random deflection function.

Sanders, J. L., Jr.↗
NASA NTRS1974

Inelastic, nonlinear analysis of stiffened shells of revolution by numerical integration

This paper describes the latest addition to the STARS system of computer programs, STARS-2P, for the plastic, large deflection analysis of axisymmetrically loaded shells of revolution. The STARS system uses a numerical integration scheme to solve the governing differential equations. Several unique features for shell of revolution programs that are included in the STARS-2P program are described. These include orthotropic nonlinear kinematic hardening theory, a variety of shell wall cross sections and discrete ring stiffeners, cyclic and nonproportional mechanical and thermal loading capability, the coupled axisymmetric large deflection elasto-plastic torsion problem, an extensive restart option, arbitrary branching capability, and the provision for the inelastic treatment of smeared stiffeners, isogrid, and waffle wall constructions. To affirm the validity of the results, comparisons with available theoretical and experimental data are presented.

Levine, H. S.↗
NASA NTRS1945

Bending and shear stresses developed by the instantaneous arrest of the root of a cantilever beam rotating with constant angular velocity about a transverse axis through the root

A theoretical investigation was made of the behavior of a cantilever beam in rotational motion about a transverse axis through the root determining the stresses, the deflections, and the accelerations that occur in the beam as a result of the arrest of motion. The equations for bending and shear stress reveal that, at a given percentage of the distance from root to tip and at a given trip velocity, the bending stresses for a particular mode are independent of the length of the beam and the shear stresses vary inversely with the length. When examined with respect to a given angular velocity instead of a given tip velocity, the equations reveal that the bending stress is proportional to the length of the beam whereas the shear stress is independent of the length. Sufficient experimental verification of the theory has previously been given in connection with another problem of the same type.

BEAMS - VIBRATION↗
NASA NTRS1985

Passive damping concepts for slender columns in space structures

An experimental and theoretical study of three different passive damping concepts is conducted for a slender member with partial rotational end restraints. Over a hundred full-scale natural vibration experiments were conducted to evaluate the effectiveness of mass-string, polyethylene tubing, and chain damping concepts. The damping properties obtained from the experiments were used in the approximate analyses based on the partial differential equation of motion for the problem. The comparison of the experimental and the theoretical deflection-time relations shows that the velocity-dependent damping model used in the theory is adequate. From the experimental results, the effect of end connection friction and induced axial forces on damping is identified. The definition of an efficiency index is proposed based on the damping ratio and the mass of a given passive damping device. Using this definition, the efficiencies of the three damping devices are compared. The polyethylene tubing concept resulted into a low damping efficiency.

Razzaq, Z.↗
NASA NTRS1993

Effect of forebody tangential slot blowing on flow about a full aircraft geometry

The effect of forebody tangential slot blowing on the flowfield about an F/A-18 aircraft is investigated numerically using solutions of the Navier-Stokes equations. Computed solutions are obtained for a full aircraft geometry, including the fuselage, wing with deflected leading-edge flap, empennage, and a faired-over engine inlet. The computational slot geometry corresponds to that used in full-scale wind tunnel tests. Solutions are computed using flight test conditions and jet mass flow ratios equivalent to wind tunnel test conditions. The effect of slot location is analyzed by computing two non-time-accurate solutions with a 16 in. slot located 3 in. and 11 in. aft of the nose of the aircraft. These computations resolve the trends observed in the full-scale wind tunnel test data. The flow aft of the leading edge extension (LEX) vortex burst is unsteady. A time-accurate solution is obtained to investigate the flow characteristics aft of the vortex burst, including the effect of blowing on tail buffet.

Gee, Ken↗
NASA NTRS1994

Modeling the effect of water on mantle rheology

To study the thermal history of the Earth we use a parameterized model of mantle convection. This model includes a mathematical description of de- and regassing processes of water from the Earth's mantle. The rates of this processes are considered to be directly proportional to the seafloor spreading rate. The kinematic viscosity of the mantle depends on the temperature/pressure as well as on the volatile content. Dissolved volatiles such as water weaken the minerals by reducing their activation energy for solid state creep. Karato and Toriumi showed a power law dependence between creep rate and water fugacity derived from experimental results. Therefore, we use such flow parameters of diffusion creep in olivine under wet and dry conditions to calculate the mantle viscosity as a function of the water content. Because the creep rate is proportional to the concentration of water-related point deflects we assume that the water fugacity is proportional to the water weight fraction. An equation for the steady-state strain rate under wet conditions is established. To assess the unknown constant K in this equation, we use flow law parameters given by Karato and Wu as well as the results of McGovern and Schubert.

Bounama, CH.↗
NASA NTRS2003

Non-Linear Structural Dynamics Characterization using a Scanning Laser Vibrometer

This paper presents the use of a scanning laser vibrometer and a signal decomposition method to characterize non-linear dynamics of highly flexible structures. A Polytec PI PSV-200 scanning laser vibrometer is used to measure transverse velocities of points on a structure subjected to a harmonic excitation. Velocity profiles at different times are constructed using the measured velocities, and then each velocity profile is decomposed using the first four linear mode shapes and a least-squares curve-fitting method. From the variations of the obtained modal \ielocities with time we search for possible non-linear phenomena. A cantilevered titanium alloy beam subjected to harmonic base-excitations around the second. third, and fourth natural frequencies are examined in detail. Influences of the fixture mass. gravity. mass centers of mode shapes. and non-linearities are evaluated. Geometrically exact equations governing the planar, harmonic large-amplitude vibrations of beams are solved for operational deflection shapes using the multiple shooting method. Experimental results show the existence of 1:3 and 1:2:3 external and internal resonances. energy transfer from high-frequency modes to the first mode. and amplitude- and phase- modulation among several modes. Moreover, the existence of non-linear normal modes is found to be questionable.

Pai, P. F.↗
NASA NTRS1952

Generalization of Boundary-Layer Momentum-Integral Equations to Three-Dimensional Flows Including Those of Rotating System

The Navier-Stokes equations of motion and the equation of continuity are transformed so as to apply to an orthogonal curvilinear coordinate system rotating with a uniform angular velocity about an arbitrary axis in space. A usual simplification of these equations as consistent with the accepted boundary-layer theory and an integration of these equations through the boundary layer result in boundary-layer momentum-integral equations for three-dimensional flows that are applicable to either rotating or nonrotating fluid boundaries. These equations are simplified and an approximate solution in closed integral form is obtained for a generalized boundary-layer momentum-loss thickness and flow deflection at the wall in the turbulent case. A numerical evaluation of this solution carried out for data obtained in a curving nonrotating duct shows a fair quantitative agreement with the measures values. The form in which the equations are presented is readily adaptable to cases of steady, three-dimensional, incompressible boundary-layer flow like that over curved ducts or yawed wings; and it also may be used to describe the boundary-layer flow over various rotating surfaces, thus applying to turbomachinery, propellers, and helicopter blades.

Mager, Arthur↗
NASA NTRSDate not supplied

Tailoring the Stiffness of Large Mirrors to Reduce Specific Optical Aberrations

Presented is a method that tailors the geometry of a mirror’s core structure as well as the mounting interface such that a desired set of aberrations is reduced. It will be shown that targeting specific aberrations as opposed to reducing overall surface figure error (SFE) is a valid method to reduce weight or improve performance. Analyzed first is the self-weight deflection of a thin circular plate of uniform thickness continuously supported along its outer edge. The Kirchhoff-Love plate bending equations are related to the radially symmetric Zernike polynomials of piston, defocus, and primary spherical aberration. Next, the mirror’s radial thickness is optimized to eliminate primary and secondary spherical aberrations when the outer edge is simply supported. As an example, the method is demonstrated using a 2-meter diameter aluminum mirror where surface deflections can have an appreciable effect at mid-to-near infrared wavelengths

mirror stiffness optimization↗
NASA NTRS1993

The effect of Reynolds number and turbulence on airfoil aerodynamics at -90 degrees incidence

A method has been developed for calculating the viscous flow about airfoils in with and without deflected flaps at -90 deg incidence. This method provides for the solution of the unsteady incompressible Navier-Stokes equations by means of an implicit technique. The solution is calculated on a body-fitted computational mesh using a staggered grid method. The vorticity is defined at the node points, and the velocity components are defined at the mesh-cell sides. The staggered-grid orientation provides for accurate representation of vorticity at the node points and the continuity equation at the mesh-cell centers. The method provides for the direct solution of the flow field and satisfies the continuity equation to machine zero at each time-step. The method is evaluated in terms of its ability to predict two-dimensional flow about an airfoil at -90 degrees incidence for varying Reynolds number and different boundary layer models. A laminar and a turbulent boundary layer models. A laminar and a turbulent boundary layer model are considered in the evaluation of the method. The variation of the average loading and surface pressure distribution due to flap deflection, Reynolds number, and laminar or turbulent flow are presented and compared with experimental results. The comparisons indicate that the calculated drag and drag reduction caused by flap deflection and the calculated average surface pressure are in excellent agreement with the measured results at a similar Reynolds number.

Stremel, Paul M.↗
NASA NTRS1999

Nonlinear Response of Composite Panels Under Combined Acoustic Excitation and Aerodynamic Pressure

A finite element formulation is presented for the analysis of large deflection response of composite panels subjected to aerodynamic pressure- at supersonic flow and high acoustic excitation. The first-order shear deformation theory is considered for laminated composite plates, and the von Karman nonlinear strain-displacement relations are employed for the analysis of large deflection panel response. The first-order piston theory aerodynamics and the simulated Gaussian white noise are employed for the aerodynamic and acoustic loads, respectively. The nonlinear equations of motion for an arbitrarily laminated composite panel subjected to a combined aerodynamic and acoustic pressures are formulated first in structure node degrees-of-freedom. The system equations are then transformed and reduced to a set of coupled nonlinear equations in modal coordinates. Modal participation is defined and the in-vacuo modes to be retained in the analysis are based on the modal participation values. Numerical results include root mean square values of maximum deflections, deflection and strain response time histories, probability distributions, and power spectrum densities. Results showed that combined acoustic and aerodynamic loads have to be considered for panel analysis and design at high dynamic pressure values.

Abdel-Motagaly, K.↗
NASA NTRS1972

In-orbit flexible spacecraft dynamics program

A continuous flexible body nonlinear dynamics computer program is used for simulating the spinning mode performance of a spacecraft under applied control torques. The program takes into account the continuous flexible nature of the antennas by representing deflections in terms of shape functions and integrated the spatial dependence in the formulation of the equations of motion. Comparison of RAE flight data on roll, pitch, and yaw with predictions of the computer program in the gravity gradient mode show fair to good agreement in roll and pitch and excellent agreement in the yaw angle.

Fedor, J. V.↗