SEARCH · Engineering Papers

Results for “cold injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Feasibility of detecting aircraft wake vortices using passive microwave radiometers

The feasibility of detecting the cold core of the wake vortex from the wingtips of an aircraft using a passive microwave radiometer was investigated. It was determined that there is a possibility that a cold core whose physical temperature drop is 10 C or greater and which has a diameter of 5 m or greater can be detected by a microwave radiometer. The radiometer would be a noise injection balanced Dicke radiometer operating at a center frequency of 60 GHz. It would require a noise figure of 5 dB, a predetection bandwidth of 6 GHz, and an integration time of 2 seconds resulting in a radiometric sensitivity of 0.018 K. However, three additional studies are required. The first would determine what are the fluctuations in the radiometric antenna temperature due to short-term fluctuations in atmospheric pressure, temperature, and relative humidity. Second, what is the effect of the pressure and temperature drop within the cold core of the wake vortex on its opacity. The third area concerns the possibility of developing a 60 GHz radiometer with a radio metric sensitivity an order of magnitude improvement over the existing state of the art.

Harrington, Richard F.↗

NASA NTRS2014

Patterns of Convective Influence and Temperature in the TTL during ATTREX

The Tropical Tropopause Layer, a zonal torus of air around 13-18km altitude and -30 to 30 latitude,is the gatekeeper for air entering the stratosphere from the troposphere. The overall speed of theupward motion affects the input of all the trace constituents, but how the upward transfer is distributedbetween convective injection and slow ascent indirectly driven by breaking waveshas a critical effect on both water and some short-lived species (e.g., bromine compounds). Convection'spotential ability to bypass the cold trap in the center of the TTL torus can contribute to stratospherichydration. Convection can also quickly move short-lived tracers to higher altitudes (and higher ozonevalues), and contribute to ozone destruction.This presentation focusses on the relationship of convectively influenced air to temperature in the TTL, withan emphasis on the qualitative evolution during ATTREX. We use a technique of obtaining global, highresolution distributions of convective cloud tops at 3-hourly intervals to derive distributions ofconvectively influenced air in the TTL, and examine its relationship to TTL temperature. TTL temperaturedistributions are often affected directly by convection, but equatorial and other gravity waves having a varietyof space and time scales are also important. The relationship of these temperature patterns to outputfrom convection will determine whether hydrated air remains in the TTL, or whether it is stripped of itswater soon after injection.

Pfister, Leonhard↗

NASA NTRS1983

LOX/hydrocarbon fuel carbon formation and mixing data analysis

By applying the Priem-Heidmann Generalized-Length vaporization correlation, the computer model developed by the present study predicts the spatial variation of propellant vaporization rate using the injector cold flow results to define the streamtubes. The calculations show that the overall and local propellant vaporization rate and mixture ratio change drastically as the injection element type or the injector operating condition is changed. These results are compared with the regions of carbon formation observed in the photographic combustion testing. The correlation shows that the fuel vaporization rate and the local mixture ratio produced by the injector element have first order effects on the degree of carbon formation.

Fang, J.↗

DOE OSTI2021

CFD-Guided Evaluation of Spark-Assisted Gasoline Compression Ignition for Cold Idle Operation

A closed-cycle, three-dimensional (3D) computational fluid dynamics (CFD) analysis campaign was conducted to evaluate the performance of using spark plugs to assist gasoline compression ignition (GCI) combustion during cold idle operations. A conventional spark plug using single-sided J-strap design was put at a location on the cylinder head to facilitate spray-guided spark assistance. Ignition was modeled with an L-type energy distribution to depict the breakdown and the arc-to-glow phases during the energy discharge process. Several key design parameters were investigated, including injector clocking, number of nozzle holes, spray inclusion angle, number of fuel injections, fuel split ratio, and fuel injection timings. The study emphasized the region around the spark gap, focusing on flame kernel formation and development and local equivalence ratio distribution. Flame kernel development and the ignition process were found to correlate strongly with the fuel stratification and the flow velocity near the spark gap. The analysis results showed that the flame kernel development followed the direction of the local flow field. In addition, the local fuel stratification notably influenced early-stage flame kernel development due to varying injection spray patterns and the fuel injection strategies. Among these design parameters, the number of nozzle holes and fuel injection timing had the most significant effects on the engine combustion performance.

42 ENGINEERING↗

NASA NTRS1999

Method and apparatus for cold gas reinjection in through-flow and reverse-flow wave rotors

A method and apparatus for cold gas reinjection in through-flow and reverse-flow wave rotors having a plurality of channels formed around a periphery thereof. A first port injects a supply of cool air into the channels. A second port allows the supply of cool air to exit the channels and flow to a combustor. A third port injects a supply of hot gas from the combustor into the channels. A fourth port allows the supply of hot gas to exit the channels and flow to a turbine. A diverting port and a reinjection port are connected to the second and third ports, respectively. The diverting port diverts a portion of the cool air exiting through the second port as reinjection air. The diverting port is fluidly connected to the reinjection port which reinjects the reinjection air back into the channels. The reinjection air evacuates the channels of the hot gas resident therein and cools the channel walls, a pair of end walls of the rotor, ducts communicating with the rotor and subsequent downstream components. In a second embodiment, the second port receives all of the cool air exiting the channels and the diverting port diverts a portion of the cool air just prior to the cool air flowing to the combustor.

Nalim, M. Razi↗

NASA NTRS2009

Cold-Flow Testing of a Proposed Integrated Center-Body Diffuser/Steam Blocker Concept for Plum Brook Station's B-2 Test Facility

The center-body diffuser (CBD) steam blocker (SB) system is a concept that incorporates a set of secondary drive nozzles into the envelope of a CBD, such that both nozzle systems (i.e., the rocket engine and the steam blocking nozzles) utilize the same supersonic diffuser, and will operate either singularly or concurrently. In this manner, the SB performs as an exhaust system stage when the rocket engine is not operating, and virtually eliminates discharge flow on rocket engine shutdown. A 2.25-percent scale model of a proposed SB integrated into a diffuser for the Plum Brook B-2 facility was constructed and cold-flow tested for the purpose of evaluating performance characteristics of various design options. These specific design options addressed secondary drive nozzle design (method of steam injection), secondary drive nozzle location relative to CBD throat, and center-body throat length to diameter (L/D) ratios. The objective of the test program is to identify the desired configuration to carry forward should the next phase of design proceed. The tested scale model can provide data for various pressure ratios; however, its design is based on a proposed B-2 spray chamber (SC) operating pressure of 4.0 psia and a steam supply pressure of 165 psia. Evaluation of the test data acquired during these tests indicate that either the discrete axial or annular nozzle configuration integrated into a CBD, with an annular throat length of 1.5 L/D at the nominal injection position, would be suitable to carry forward from the SB's perspective. Selection between these two then becomes more a function of constructability and implementation than performance. L/D also has some flexibility, and final L/D selection can be a function of constructability issues within a limited range.

Edwards, Daryl A.↗

DOE OSTI2024

Constraining neutrino-DM interactions with Milky Way dwarf spheroidals and supernova neutrinos

We constrain the neutrino-dark matter cross section using properties of the dark matter density profiles of Milky Way dwarf spheroidal galaxies. The constraint arises from core-collapse supernova neutrinos scattering on dark matter as a form of energy injection, allowing the transformation of the dark matter density profile from a cusped profile to a flatter profile. We assume a standard cosmology of dark energy and cold, collisionless, and non-self-interacting dark matter. By requiring that the dark matter cores do not lose too much mass or overshoot constraints from stellar kinematics, we place an upper limit on the cross section of σ ν − DM ( E ν = 15 MeV , m χ ≲ 130 GeV ) ≈ 3.4 × 10 − 23 cm 2 and σ ν − DM ( E ν = 15 MeV , m χ ≳ 130 GeV ) ≈ 3.2 × 10 − 27 ( m χ 1 GeV ) 2 cm 2 , which is stronger than previous bounds for these energies. Consideration of baryonic feedback or host galaxy effects on the dark matter profile can strengthen this constraint. Published by the American Physical Society 2024

Astronomy & Astrophysics↗

NASA NTRS1975

Theoretical and experimental study of flow through turbine cascades with coolant flow injection

An analytical study is presented which deals with the change in the outlet flow conditions from a turbine blade row due to coolant air injection through slots. The analysis applies to small secondary to primary mass flow ratios, taking into consideration the change in boundary layer development resulting from injection. The effects of injection location, injection flow angle and injected air momentum flux are investigated. The results of the present analysis are compared with the values obtained using the mixing theory method and experimental data from cold flow tests in a turbine cascade tunnel.

Tabakoff, W.↗

NASA NTRS1977

Cold plasma diagnostics using satellite measurements of VLF signals from ground transmitters

A diagnostic technique to obtain the cold-plasma density profile in the magnetosphere is introduced. This method uses satellite measurements of group delay and pulse duration of VLF signals from ground transmitters in conjunction with a detailed ray-tracing analysis. An iterative method is involved which starts with an approximate density profile, computes the ray paths for that profile, and then compares the properties of the rays that reach the satellite location with the actual satellite measurements. The density profile is then modified to account for any discrepancies between the two results. The same process is repeated with the new profile until one has reasonable agreement between the data and ray-tracing results. This method is applied to the case of an Imp 6 pass, where strong signals from the Siple VLF transmitter were observed for over 25 min. Good agreement is found between the results of the proposed technique and the well-known ground whistler techniques of cold-plasma diagnostics. The results also serve to illustrate the wide diversity of propagation paths from ground transmitters to high-altitude satellites during VLF wave-injection experiments.

Inan, U. S.↗

NASA NTRS1977

Effect of endwall cooling on secondary flows in turbine stator vanes

An experimental investigation was performed to determine the effect of endwall cooling on the secondary flow behavior and the aerodynamic performance of a core-turbine stator vane. The investigation was conducted in a cold-air, full-annular cascade, where three-dimensional effects could be obtained. In one configuration, the cooling holes were oriented so that the coolant was injected in line with the inviscid streamline direction. In another configuration, the coolant was injected at an angle of 15 deg to the inviscid streamline direction and oriented toward the vane pressure surface. Total-pressure surveys were taken downstream of the stator vanes over a range of cooling flows. Changes in the total-pressure contours downstream of the vanes were used to obtain the effect of endwall cooling on the secondary flows in the stator. Comparisons are made between the two cooled-endwall configurations and with the results obtained previously for solid (uncooled) endwalls.

Goldman, L. J.↗

NASA NTRS1978

The collisional interaction of a beam of charged particles with a hydrogen target of arbitrary ionization level

The classical theory of scattering under the Coulomb potential of both charged and neutral particles is used to derive formulae for the energy deposition rate and mean scattering of a beam of charged particles interacting with a cold hydrogen target of arbitrary ionization level as a function of the column density traversed by the beam. These general results hold for any form of stable injection energy spectrum, and their relevance to the existing literature on chromospheric heating during solar flares is discussed.

Emslie, A. G.↗

NASA NTRS2014

A Method for Obtaining High Time and Spatial Resolution Convective Cloud Top Data for the TTL

A method for obtaining high time and spatial resolution convective cloud top data for the TTL Leonhard Pfister, Eric Jensen, Rei Ueyama, Eliot Atlas, and Maria Navarro Convective systems in the tropics have a maximum in the cloud top altitude distribution of about 13.5 km. However, there is a significant tail to this distribution -- a few percent reach the cold point tropopause (CPT) at 16.5 km, and there has been clear evidence of convective mass deposited as high as 19 km in the tropics. The region between 13.5 km and the cold point tropopause is transitional, between the free tropical troposphere where convective mixing dominates, and the stratosphere where slow upward ascent dominates. In this region (the Tropical Tropopause Layer), convective injection, slow ascent, and mixing from midlatitudes all have similar time scales. So, even though only a few percent of convective systems reach the CPT, convection is important. Space Based Lidar and cloud radar measurements have yielded information about long term average statistical distributions of cloud altitude as a function of location. However, we also need time-dependent cloud top altitude and cloud top potential temperature information, primarily to understand the water vapor and TTL cloud distributions. This is because the effect of convection depends on the local temperature, and on the subsequent temperature history. Time dependent cloud top information is also needed to understand short-lived tracers because cross-isentropic flow is time and space dependent. This paper presents a method of obtaining time and space dependent convective cloud top theta (and altitude) information using 3-hourly geostationary brightness temperature data, coupled with global 3 -hourly rainfall estimates and temperature analyses. We explore different mixing algorithms to obtain the most reasonable agreement with near-simultaneous observations by cloudsat and calipso. Observations of short-lived tracers from ATTREX, coupled with short-term trajectories are used to test the method's accuracy. An important caveat is the ambiguity of evaluating convective cloud top altitudes under from combined cloudsat and calipso measurements.

cold point tropopause (CPT)↗

NASA NTRS2015

Simulation of Cold Flow in a Truncated Ideal Nozzle with Film Cooling

Flow transients during rocket start-up and shut-down can lead to significant side loads on rocket nozzles. The capability to estimate these side loads computationally can streamline the nozzle design process. Towards this goal, the flow in a truncated ideal contour (TIC) nozzle has been simulated using RANS and URANS for a range of nozzle pressure ratios (NPRs) aimed to match a series of cold flow experiments performed at the NASA MSFC Nozzle Test Facility. These simulations were performed with varying turbulence model choices and for four approximations of the supersonic film injection geometry, each of which was created with a different simplification of the test article geometry. The results show that although a reasonable match to experiment can be obtained with varying levels of geometric fidelity, the modeling choices made do not fully represent the physics of flow separation in a TIC nozzle with film cooling.

Braman, K. E.↗

NASA NTRS2016

Computational Flow Field in Energy Efficient Engine (EEE)

In this paper, preliminary results for the recently-updated Open National Combustion Code (Open NCC) as applied to the EEE are presented. The comparison between two different numerical schemes, the standard Jameson-Schmidt-Turkel (JST) scheme and the advection upstream splitting method (AUSM), is performed for the cold flow and the reacting flow calculations using the RANS. In the cold flow calculation, the AUSM scheme predicts a much stronger reverse flow in the central recirculation zone. In the reacting flow calculation, we test two cases: gaseous fuel injection and liquid spray injection. In the gaseous fuel injection case, the overall flame structures of the two schemes are similar to one another, in the sense that the flame is attached to the main nozzle, but is detached from the pilot nozzle. However, in the exit temperature profile, the AUSM scheme shows a more uniform profile than that of the JST scheme, which is close to the experimental data. In the liquid spray injection case, we expect different flame structures in this scenario. We will give a brief discussion on how two numerical schemes predict the flame structures inside the EEE using different ways to introduce the fuel injection.

CFD↗

DOE OSTI2024

Designing a Convection‐Cloud Chamber for Collision‐Coalescence Using Large‐Eddy Simulation With Bin Microphysics

Abstract Collisional growth of cloud droplets is an essential yet uncertain process for drizzle and precipitation formation. To improve the quantitative understanding of this key component of cloud‐aerosol‐turbulence interactions, observational studies of collision‐coalescence in a controlled laboratory environment are needed. In an existing convection‐cloud chamber (the Pi Chamber), collisional growth is limited by low liquid water content and short droplet residence times. In this work, we use numerical simulations to explore various configurations of a convection‐cloud chamber that may intensify collision‐coalescence. We employ a large‐eddy simulation (LES) model with a size‐resolved (bin) cloud microphysics scheme to explore how cloud properties and the intensity of collision‐coalescence are affected by the chamber size and aspect ratio, surface roughness, side‐wall wetness, side‐wall temperature arrangement, and aerosol injection rate. Simulations without condensation and evaporation within the domain are first performed to explore the turbulence dynamics and wall fluxes. The LES wall fluxes are used to modify the Scalar Flux‐budget Model, which is then applied to demonstrate the need for non‐uniform side‐wall temperature (two side walls as warm as the bottom and the two others as cold as the top) to maintain high supersaturation in a tall chamber. The results of LES with full cloud microphysics reveal that collision‐coalescence is greatly enhanced by employing a taller chamber with saturated side walls, non‐uniform side‐wall temperature, and rough surfaces. For the conditions explored, although lowering the aerosol injection rate broadens the droplet size distribution, favoring collision‐coalescence, the reduced droplet number concentration decreases the frequency of collisions.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2026

First field test of a novel optical gas analyser in the exhaust of Wendelstein 7-X

A novel optical gas analyser, designed for isotope-resolved exhaust composition measurement, was field-tested at Wendelstein 7-X (W7-X) to validate its laboratory-proven concept under operational fusion experiment conditions. The system, Optix, comprises a cold cathode remote plasma generator and a high-resolution Fabry–Perot spectrometer and was deployed in the exhaust line of W7-X during the OP2.3 campaign. The injection of 3 He and 4 He for minority ion-cyclotron heating provided a test case for helium isotope discrimination. Despite limitations due to background gas and low partial pressures of the target species, isotope-resolved spectral signatures were successfully observed, demonstrating the fundamental viability of the Optix approach. Additionally, the spectrometer was evaluated for plasma emission measurements from both core and edge sightlines. While helium line emission was detectable, interpretation was hindered by complex background signals, highlighting the benefits of controlled remote plasma generators for spectroscopy. This first deployment provides critical insight into pressure requirements, spectral resolution, and operational constraints, informing future applications of optical exhaust diagnostics in fusion devices.

magnetic confinement fusion↗

NASA NTRS1982

Particle precipitation induced by short-duration VLF waves in the magnetosphere

The present investigation has the objective to study the precipitation of energetic electrons into the ionosphere due to the interaction of these particles with short-duration VLF waves in the magnetosphere. The physics of the interaction is considered, taking into account the wave structure, the energetic particle distribution, wave-particle interaction, and the computation of the precipitated flux versus time. The obtained formulation is applied to various different magnetospheric conditions. Attention is also given to peak flux and total deposited energy. The results of the investigation demonstrate the role of the energetic particle distribution function, the normalized wave frequency, the L value of the path of propagation, the cold plasma density, and the wave intensity. The precipitated energy flux that would be observed at 1000-km altitude is presented as a function of time relative to the injection of the wave pulse at the same point.

Inan, U. S.↗

NASA NTRS1991

Supersonic mixing and combustion in scramjets

Experimental and theoretical studies are being conducted to explore techniques to enhance mixing in scramjet combustors using parallel fuel injection from the base of swept and unswept wall-mounted ramps. The experiments reported herein were conducted using Mach 2 and 3 combustor inlet conditions. Supporting computational and cold flow studies indicated that the observed enhanced mixing for the swept ramp configuration is primarily due to the substantially higher degree of vorticity and entrainment generated by the swept trailing edges.

Northam, G. B.↗