Experimental verification of effects of turbulent boundary layers on chemical-kinetic measurements in a shock tube
Turbulent boundary layers produced by nonuniform shock tube flow, considering effects on chemical kinetic measurements
Belles, F. E.↗
SEARCH · Engineering Papers
Results for “boundary effects”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Unsteady turbulent boundary layers - Some effects of abrupt free-stream velocity changes
The response of a turbulent boundary layer to abrupt changes in free-stream velocity is studied. Streamwise velocity measurements are examined during the abrupt events and after them, as the flow relaxes to its equilibrium condition. The measured velocity field is found to be in good agreement with the analytic solution of the Stokes equation for boundary conditions describing abrupt changes. While the flow recovers to its equilibrium state, changes in integral, boundary-layer parameters scale on the local free-stream time of flight.
Brereton, G. J.↗
Hypersonic Boundary Layer Stability Experiments in a Quiet Wind Tunnel with Bluntness Effects
Hypersonic boundary layer measurements over a flared cone were conducted in a Mach 6 quiet wind tunnel at a freestream unit Reynolds number of 2.82 million/ft. This Reynolds number provided laminar-to-transitional flow over the cone model in a low-disturbance environment. Four interchangeable nose-tips, including a sharp-tip, were tested. Point measurements with a single hot-wire using a novel constant voltage anemometer were used to measure the boundary layer disturbances. Surface temperature and schlieren measurements were also conducted to characterize the transitional state of the boundary layer and to identify instability modes. Results suggest that second mode disturbances were the most unstable and scaled with the boundary layer thickness. The second mode integrated growth rates compared well with linear stability theory in the linear stability regime. The second mode is responsible for transition onset despite the existence of a second mode subharmonic. The subharmonic disturbance wavelength also scales with the boundary layer thickness. Furthermore, the existence of higher harmonics of the fundamental suggests that nonlinear disturbances are not associated with 'high' free stream disturbance levels. Nose-tip radii greater than 2.7% of the base radius completely stabilized the second mode.
Lachowicz, Jason T.↗
The growth of the tearing mode - Boundary and scaling effects
A numerical model of resistive magnetic tearing is developed in order to verify and relate the results of the principal approximations used in analytic analyses and to investigate the solutions and their growth-rate scalings over a large range of primary parameters which include parametric values applicable to the solar atmosphere. The computations cover the linear behavior for a variety of boundary conditions, emphasizing effects which differentiate magnetic tearing in astrophysical situations from that in laboratory devices. Eigenfunction profiles for long and short wavelengths are computed and the applicability of the 'constant psi' approximation is investigated. The growth rate is computed for values of the magnetic Reynolds number up to a trillion and of the dimensionless wavelength parameter down to 0.001. The analysis predicts significant effects due to differing values of the magnetic Reynolds number.
Steinolfson, R. S.↗
Investigation of sidewall boundary layer removal effects on two different chord airfoil models in the Langley 0.3-meter Transonic Cryogenic Tunnel
An investigation was carried out on two CAST 10-2 airfoil models with chords of 3 in. and 6 in. To evaluate the extent of sidewall influence on airfoil tests at transonic Mach numbers. The tests were conducted in the Langley 0.3-m Transonic Cryogenic Tunnel two-dimensional test section equipped with an upstream sidewall boundary layer removal system which reduces the boundary layer displacement thickness to about 1 percent of model halfspan from an initial 2 percent without boundary layer removal. Test results have shown the changes in the location of the shock on the upper surface of the airfoil to be about the same for both models with and without sidewall boundary layer removal. Even though large differences were noted in the high lift characteristics of the two models, the sidewall boundary layer removal had little effect on the differences. These tests also served to validate the boundary layer removal technique and the associated Mach number correction required with upstream boundary layer removal.
Murthy, A. V.↗
Flight survey of the 757 wing noise field and its effects on laminar boundary layer transition. Volume 2: Data compilation
A flight test program was performed using the Boeing 757 flight research airplane to investigate the effect of noise from wing mounted engines on laminar boundary layer transition. An NLF glove was installed on the right wing panel just outboard of the engine. The extent of laminar flow on the glove was measured as a function of engine power setting for a range of flight conditions. A combination of surface and probe microphones was distributed over the upper and lower wing surfaces to measure sound spectra. The flight test program was completed in June 1985 and the results of preliminary analysis indicate that a maximum of about 29 percent of chord laminar flow was obtained on the upper surface and about 28 percent on the lower surface (at a high sideslip condition). The engine speed was varied from about 2600 (idle) to about 4500 (maximum continuous power) r/min. This produced changes in sound pressure level up to 20 dB on the lower surface. On the upper surface, the noise levels were independent of engine power but sensitive to airplane Mach number. No effect of engine power setting on upper surface transition location was observed, and only a small forward movement of the transition location on the lower surface was observed at the high power settings. Volume 1 of this report contains the program description and data analysis. Volume 2 is a compilation of all of the flight test data.
Source record↗
Nongray radiation effects on the hypersonic boundary layer over a flat plate.
Nongray radiation effects on laminar boundary layer of absorbing gas over flat plate, using absorption coefficient with stepwise frequency dependence
ABSORPTION COEFFICIENT↗
Experiment on convex curvature effects in turbulent boundary layers.
Turbulent boundary layers along a convex surface of varying curvature were investigated in a specially designed boundary-layer tunnel. A fairly complete set of turbulence measurements was obtained. The effect of curvature is striking. For example, along a convex wall the Reynolds stress is decreased near the wall and vanishes about midway between the wall and the edge of a boundary layer where there exists a velocity profile gradient created upstream of the curved wall.
So, R. M. C.↗
Experimental studies of hypersonic boundary-layer transition and effects of wind tunnel disturbances
Boundary layer transition data on cones and free stream disturbance levels were measured in a hypersonic wind tunnel and Mach 8 variable density hypersonic tunnel. Transition data were obtained by using different conical models and techniques for detecting the location of transition. The disturbance levels were measured by using hot wire anemometry and pressure transducers. The transition Reynolds numbers obtained from the tests correlated well when the fluctuating pressures measured at the surface of conical models were used as a correlating parameter.
Stainback, P. C.↗
Flight survey of the 757 wing noise field and its effects on laminar boundary layer transition. Volume 3: Extended data analysis
A flight program was completed in June of 1985 using the Boeing 757 flight research aircraft with an NLF glove installed on the right wing just outboard of the engine. The objectives of this program were to measure noise levels on the wing and to investigate the effect of engine noise on the extent of laminar flow on the glove. Details of the flight test program and results are contained in Volume 1 of this document. Tabulations and plots of the measured data are contained in Volume 2. The present volume contains the results of additional engineering analysis of the data. The latter includes analysis of the measured noise data, a comparison of predicted and measured noise data, a boundary layer stability analysis of 21 flight data cases, and an analysis of the effect of noise on boundary layer transition.
Source record↗
Exploratory Investigation of the Effects of Boundary-Layer Control on the Pressure-Recovery Characteristics of a Circular Internal-Contraction Inlet with Translating Centerbody at Mach Numbers of 2.00 and 2.35
Exploratory tests of a circular internal-contraction inlet were made at Mach numbers of 2.00 and 2.35 to determine the effect of a cowl-type boundary-layer control located downstream of the inlet throat. The inlet was designed for a Mach number of 2.5. Tests were also made of the inlet modified to correspond to design Mach numbers of 2.35 and 2.25. Surveys near the minimum area section of the inlet without boundary-layer control indicated maximum averaged pressure recoveries between 0.90 and 0.92 at a free-stream Mach number, M(sub infinity), of 2.35 for the inlets. Farther downstream, after partial subsonic diffusion, a maximum pressure recovery of 0.842 was obtained with the inlet at M(sub infinity) = 2.35. The pressure recovery of the inlet was increased by 0.03 at a Mach number of 2.35 and decreased by 0.02 at a Mach number of 2.00 by the application of cowl-type boundary-layer control. Further investigation with the inlet without bleed demonstrated that an increase of angle of attack from 0 deg to 3 deg reduced the pressure recovery 0.04. The effect of Reynolds number was to increase pressure recovery 0.07 (from 0.785 to 0.855) with an increase in Reynolds number (based on inlet diameter) from 0.79 x 10(exp 6) to 3.19 x 10(exp 6).
Martin, Norman J.↗
Effect of Far-Field Boundary Conditions on Boundary-Layer Transition
The effect of far-field boundary conditions on the evolution of a finite-amplitude two-dimensional wave in the Blasius boundary layer is assessed. With the use of the parabolized stability equations (PSE) theory for the numerical computations, either asymptotic, Dirichlet, Neumann or mixed boundary conditions are imposed at various distances from the wall. The results indicate that asymptotic and mixed boundary conditions yield the most accurate mean-flow distortion and unsteady instability modes in comparison with the results obtained with either Dirichlet or Neumann conditions.
Bertolotti, Fabio P.↗
Effect of Far-Field Boundary Conditions on Boundary-Layer Transition
The effect of far-field boundary conditions on the evolution of a finite-amplitude two-dimensional wave in the Blasius boundary layer is assessed. With the use of the parabolized stability equations (PSE) theory for the numerical computations, either asymptotic, Dirichlet, Neumann or mixed boundary conditions are imposed at various distances from the wall. The results indicate that asymptotic and mixed boundary conditions yield the most accurate mean-flow distortion and unsteady instability modes in comparison with the results obtained with either Dirichlet or Neumann conditions.
Bertolotti, Fabio P.↗
The effect of closed boundary conditions on a stationary dynamo
One of two boundary conditions generally assumed in solutions of the dynamo equation is related to the disappearance of the azimuthal field at the boundary. Parker (1984) points out that for the realization of this condition the field must escape freely through the surface. Escape requires that the field be detached from the gas in which it is embedded. In the case of the sun, this can be accomplished only through reconnection in the tenuous gas above the visible surface. Parker concludes that the observed magnetic activity on the solar surface permits at most three percent of the emerging flux to escape. He arrives at the conclusion that, instead of B(phi) = 0, the partial derivative of B(phi) to r is equal to zero. The present investigation is concerned with the effect of changing the boundary condition according to Parker's conclusion. Implications for the solar convection zone are discussed.
Choudhuri, A. R.↗
Heat transfer through turbulent boundary layers - The effects of introduction of and recovery from convex curvature
Measurements have been made of the heat transfer through a turbulent boundary layer on a convexly curved isothermal wall and on a flat plate following the curved section. Data were taken for one free-stream velocity and two different ratios of boundary layer thickness to radius of curvature delta/R = 0.051 and delta/R = 0.077. Only small differences were observed in the distribution of heat transfer rates for the two boundary layer thicknesses tested, although differences were noted in the temperature distributions within the boundary layer
Simon, T. W.↗
An evaluation of several compressible turbulent boundary-layer models Effects of pressure gradient and Reynolds number
Computations, employing several turbulence models, are compared with a series of attached supersonic turbulent boundary-layer experiments over an extensive range of Reynolds numbers (11.7 x 10 to the 6th to 314 x 10 to the 6th). These experiments included measurements of surface pressure and skin friction for adverse pressure gradients ranging in magnitude from those of previous investigations to an order of magnitude greater. The turbulence models evaluated include algebraic and two-equation eddy-viscosity models and two full Reynolds stress models. In general all the models tested performed well independently of the magnitude of the pressure gradient or Reynolds number and could predict the measured skin friction for most cases with sufficient accuracy for engineering purposes.
Horstman, C. C.↗
Scale effects on turbulent boundary layer development and flow separation around V/STOL inlets at high incidence
Numerical methods for calculating laminar and turbulent boundary layers development around V/STOL engine inlets at high incidence angles, along with the procedures for predicting flow separation, are presented. Results of scale-effects, which are obtained by a numerical scaling procedure on the boundary layer characteristics and incidence angles at onset of separation are discussed. The interesting 'cross-over' phenomena, where the full-scale models actually exhibit earlier separation than the scaled-models, is illustrated for a typical V/STOL inlet at a certain operating condition. Some of the numerical results are compared with the existing wind-tunnel test data for a 1/6 scale inlet model to demonstrate the validity of the numerical approach.
Chou, D. C.↗
The structure of a separating turbulent boundary layer. IV - Effects of periodic free-stream unsteadiness
Measurements were obtained of the sinusoidal unsteadiness of the free stream velocity during the separation of the turbulent boundary layer. Data were gathered by single wire and cross-wire, anemometry upstream of flow detachment, by laser Doppler velocimetry to detect the movement of the flow in small increments, and by a laser anemometer in the detached zone to measure turbulence and velocities. The study was restricted to a sinusoidal instability frequency of 0.61 and a ratio of oscillation amplitude to mean velocity of 0.3. Large amplitude and phase variations were found after the detachment, with unsteady effects producing hysteresis in the relationships between flow parameters. The detached shear layer decreased in thickness with increasing free-stream velocity and increases in the Reynolds shear stress. Deceleration of the free stream velocity caused thickening in the shear layer and upstream movement of the flow reversal location. The results are useful for studies of compressor blade and helicopter rotors in transition.
Simpson, R. L.↗