Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bit error rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

On the passage of high-level pulsed radio frequency interference through a nonlinear satellite transponder

Attention is given to the uncoded bit error rate (BER) performance of a satellite communications system whose modulation scheme is binary PSK and whose transponder contains an arbitrary amplitude nonlinearity, all in the presence of high level pulsed radio frequency interference (RFI). A general approach is presented for direct BER evaluations, in contrast to other approaches which may employ SNR suppression factors. The computed results are based on arbitrarily specified RFI scenarios, in the presence of hard limiter, clipper, or blanker amplitude nonlinearities. Performance curves demonstrate the superiority of an appropriately chosen blanker when the RFI environment is most severe. The results obtained also pertain to the sensitivity of performance to the information bit rate, signal power variations, and the ratio of CW to noise content. The CW effects are found to be the most severe.

Weinberg, A.↗
NASA NTRS1971

Performance results for a hybrid coding system.

Results of computer simulation studies of the hybrid pull-up bootstrap decoding algorithm, using a constraint length 24, nonsystematic, rate 1/2 convolutional code for the symmetric channel with both binary and eight-level quantized outputs. Computational performance was used to measure the effect of several decoder parameters and determine practical operating constraints. Results reveal that the track length may be reduced to 500 information bits with small degradation in performance. The optimum number of tracks per block was found to be in the range from 7 to 11. An effective technique was devised to efficiently allocate computational effort and identify reliably decoded data sections. Long simulations indicate that a practical bootstrap decoding configuration has a computational performance about 1.0 dB better than sequential decoding and an output bit error rate about .0000025 near the R sub comp point.

Hoffman, L. B.↗
NASA NTRS1992

Rate 3/4 coded 16-QAM for uplink applications

First phase development of an advanced modulation technology which synergistically combines coding and modulation to achieve 2 bits per second per Hertz bandwidth efficiency in satellite demodulators is nearing completion. A proof-of-concept model is being developed to demonstrate technology feasibility, establish practical bandwidth efficiency limitations, and provide a data base for the design and development of engineering model satellite demodulators. The basic considerations leading to the choice of 4 x 4 quadrature amplitude modulation (16-QAM) and its associated coding format are discussed, along with the basic implementation of the carrier and clock recovery, automatic gain control, and decoding process. Preliminary performance results are presented. Spectra for the modulated signal shows the effects of the square root Nyquist filters in the modulation. Bit error rate (BER) results for the encoder/decoder subsystem show near ideal results, although power consumption is high and baseband BER performance of the Nyquist filter set is poor. Recommendations regarding the present system to improve BER performance and acquisition speed are given.

Mrozek, Eric M.↗
NASA NTRS1992

Rate 8/9 coded 8-PSK system for downlink applications

An advanced Coded Trellis Modulation (CTM) System which achieves a 2 bits/s/Hz bandwidth efficiency at an information rate of 200 Mbit/s while minimizing satellite power requirements, was developed for downlink earth station applications. The CTM system employs a high-speed rate 8/9 convolutional code with Viterbi decoding and an 8-Phase Shift Keying (PSK) modem. The minimum Euclidean distance between the modulated waveforms corresponding to the information sequences are maximized in order to maximize the noise immunity of the system. Nyquist filters with a square-root of 40 percent roll-off are used at the transmit and receive sides of the modem in order to minimize intersymbol interference, adjacent channel interference, and distortion at the nonlinear satellite power amplifier. The use of a coded system here also minimizes the effects of co-channel interference. The developed performance of the hardware system was measured to achieve within 1.5 dB from theory at a bit error rate of 5 x 10(exp -7) over an additive white Gaussian noise channel.

Fang, Russell↗
NASA NTRS1993

SATCOM simulator speeds MSS deployment and lowers costs

Mobile satellite systems (MSS) are being proposed and licensed at an accelerating rate. How can the design, manufacture, and performance of these systems be optimized at costs that allow a reasonable return on investment? The answer is the use of system simulation techniques beginning early in the system design and continuing through integration, pre- and post-launch monitoring, and in-orbit monitoring. This paper focuses on using commercially available, validated simulation instruments to deliver accurate, repeatable, and cost effective measurements throughout the life of a typical mobile satellite system. A satellite communications test set is discussed that provides complete parametric test capability with a significant improvement in measurement speed for manufacturing, integration, and pre-launch and in-orbit testing. The test set can simulate actual up and down link traffic conditions to evaluate the effects of system impairments, propagation and multipath on bit error rate (BER), channel capacity and transponder and system load balancing. Using a standard set of commercial instruments to deliver accurate, verifiable measurements anywhere in the world speeds deployment, generates measurement confidence, and lowers total system cost.

Carey, Tim↗
NASA NTRS2002

On-Orbit Performance Verification and End-to-End Characterization of the TDRS-H Ka-Band Communications Payload

In June 2000, NASA launched the first of three next generation Tracking and Data Relay Satellites (TDRS-H) equipped with a Ka-band forward and return service capability. This Ka-band service supports forward data rates up to 25 Mb/sec using the 22.55 - 23.55 GHz space-to-space allocation. Return services are supported via channel bandwidths of 225 and 650 MHz for data rates up to 800 Mb/sec (QPSK) using the 25.25 - 27.5 GHz space-to-space allocation. As part of NASA's acceptance of the TDRS-H spacecraft, an extensive on-orbit calibration, verification and characterization effort was performed to ensure that on-orbit spacecraft performance is within specified limits. This process verified the compliance of the Ka-band communications payload with all performance specifications and demonstrated an end-to-end Ka-band service capability. This paper summarizes the results of the TDRS-H Ka-band communications payload on-orbit performance verification and end-to-end service characterization. Performance parameters addressed include Effective Isotropically Radiated Power (EIRP), antenna Gain-to-System Noise Temperature (G/T), antenna gain pattern, frequency tunability and accuracy, channel magnitude response, and Ka-band service Bit-Error-Rate (BER) performance.

Toral, Marco↗
NASA NTRS2002

On-Orbit Performance Verification and End-To-End Characterization of the TDRS-H Ka-band Communications Payload

In June 2000, NASA launched the first of three next generation Tracking and Data Relay Satellites (TDRS-H) equipped with a Ka-band forward and return service capability. This Ka-band service supports forward data rates of up to 25 Mb/sec using the 22.55-23.55 GHz space-to-space allocation. Return services are supported via channel bandwidths of 225 and 650 MHz for data rates up to at least 800 Mb/sec using the 25.25 - 27.5 GHz space-to-space allocation. As part of NASA's acceptance of the TDRS-H spacecraft, an extensive on-orbit calibration, verification and characterization effort was performed to ensure that on-orbit spacecraft performance is within specified limits. This process verified the compliance of the Ka-band communications payload with all performance specifications, and demonstrated an end-to-end Ka-band service capability. This paper summarizes the results of the TDRS-H Ka-band communications payload on-orbit performance verification and end-to-end service characterization. Performance parameters addressed include antenna gain pattern, antenna Gain-to-System Noise Temperature (G/T), Effective Isotropically Radiated Power (EIRP), antenna pointing accuracy, frequency tunability, channel magnitude response, and Ka-band service Bit-Error-Rate (BER) performance.

Toral, Marco↗
NASA NTRS2020

Q4 – A CubeSat Mission to Demonstrate Omnidirectional Optical Communications

We are proposing a technology demonstration mission for JPL’s Inter-Satellite Optical Communicator (ISOC). The ISOC has the potential to enable up to 1 Gbps data rates over a distance up to 200 km in free space. Key features of the ISOC include full sky coverage and the ability to maintain multiple links simultaneously. The Q4 mission consists of (4) 6U CubeSats furnished with ISOCs to demonstrate high data rate communications among the spacecraft. More specifically, we seek to demonstrate the omnidirectionality of the ISOC by providing simultaneous optical links between one spacecraft and the other three. Q4 will be a demonstrator for small spacecraft swarm capabilities. Following a proposed deployment from the ISS, the CubeSats will utilize their onboard thrusters to enter their desired orbit. The orbit consists of one “leader” spacecraft in a circular orbit with a 400 km LEO altitude and three “follower” spacecraft in slightly elliptical orbits rotating azimuthally about the leader. The main mission will consist of three consecutive phases: First, the spacecraft will demonstrate pointing, acquisition, and tracking using newly developed protocols. Next, link establishment and different channel access methods (CDMA and TDMA) will be tested. Finally, Delay Tolerant Network protocols will be implemented to allow fast data sharing among the spacecraft. The distance between the communicating spacecraft will be increased as the mission progresses to characterize the link quality as a function of distance. All communications over the course of the mission will be recorded and analyzed on the ground using bit error rate as a metric for success. The current design for each the four Q4 CubeSats contains an XACT advanced ADCS system for precision beam pointing. Other components currently under consideration include MiPS cold gas thrusters for orbital maneuvering and gimbaled eHaWK 84W solar arrays. In this paper we present design considerations for the Q4 CubeSats, link budget calculations, results from preliminary mission analysis, and expected results.

Velazco, Jose E↗
NASA NTRS1994

Advanced technology for a satellite multichannel demultiplexer/demodulator

Satellite on-board processing is needed to efficiently service multiple users while at the same time minimizing earth station complexity. The processing satellite receives a wideband uplink at 30 GHz and down-converts it to a suitable intermediate frequency. A multichannel demultiplexer then separates the composite signal into discrete channels. Each channel is then demodulated by bulk demodulators, with the baseband signals routed to the downlink processor for retransmission to the receiving earth stations. This type of processing circumvents many of the difficulties associated with traditional bent-pipe repeater satellites. Uplink signal distortion and interference are not retransmitted on the downlink. Downlink power can be allocated in accordance with user needs, independent of uplink transmissions. This allows the uplink users to employ different data rates as well as different modulation and coding schemes. In addition, all downlink users have a common frequency standard and symbol clock on the satellite, which is useful for network synchronization in time division multiple access schemes. The purpose of this program is to demonstrate the concept of an optically implemented multichannel demultiplexer (MCD). A proof-of-concept (POC) model has been developed which has the ability to receive a 40 MHz wide composite signal consisting of up to 1000 40 kHz QPSK modulated channels and perform the demultiplexing process. In addition a set of special test equipment (STE) has been configured to evaluate the performance of the POC model. The optical MCD is realized as an acousto-optic spectrum analyzer utilizing the capability of Bragg cells to perform the required channelization. These Bragg cells receive an optical input from a laser source and an RF input (the signal). The Bragg interaction causes optical output diffractions at angles proportional to the RF input frequency. These discrete diffractions are optically detected and output to individual demodulators for baseband conversion. Optimization of the MCD design was conducted in order to achieve a compromise between two opposing sources of signal degradation: adjacent channel interference and intersymbol interference. The system was also optimized to allow simple, inexpensive ground stations communications with the MCD. These design goals led to the realization of a POC MCD which demonstrates the demultiplexing function with minimal signal degradation. Performance evaluation results using the STE equipment indicate that the dynamic range of the demultiplexer in the presence of adjacent and multiple channel loading is 40 - 50 dB. Measured bit error rate (BER) probabilities varied from the predicted theoretical results by one dB or less. The performance of the proof-of-concept model indicate that the development of a space qualified optically implemented MCD are feasible. The advantages to such an implementation include reduced size, weight and power and increased reliability when compared with electronic approaches. All of these factors are critical to on-board satellite processors. Further optimization can be conducted which trade ground station complexity and MCD performance to achieve desired system results.

Abramovitz, Irwin J.↗
NASA NTRS1970

Digital demodulation with data subcarrier tracking

Digital demodulator is based on early-late bit timing scheme coupled with Costas data tracking loop. System is successful in enhancement of weak signals from space where atmospheric and other interference media cause bit error rate to reach excessive level.

Sanger, D. K.↗
NASA NTRS1972

A study of FM threshold extension techniques

The characteristics of three postdetection threshold extension techniques are evaluated with respect to the ability of such techniques to improve the performance of a phase lock loop demodulator. These techniques include impulse-noise elimination, signal correlation for the detection of impulse noise, and delta modulation signal processing. Experimental results from signal to noise ratio data and bit error rate data indicate that a 2- to 3-decibel threshold extension is readily achievable by using the various techniques. This threshold improvement is in addition to the threshold extension that is usually achieved through the use of a phase lock loop demodulator.

Arndt, G. D.↗
NASA NTRS1973

Balloon atmospheric propagation experiment measurements

High altitude balloon measurements on laser beam fading during propagation through turbulent atmosphere show that a correlation between fading strength and stellar scintillation magnitudes exists. Graphs for stellar scintillation as a function of receiver aperture are used to predict fading bit error rates for neodymium-yag laser communication system.

Minott, P. O.↗
NASA NTRS1972

The ERTS wideband image communication system.

The ERTS payload includes a three camera return beam vidicon (RBV) television system and a four channel multispectral scanner system (MSS). The communications system described includes spacecraft wideband equipment plus unique payload processing equipment located at three NASA tracking stations. The RBV information, transmitted as analog FM with a baseband response of dc to 3.2 MHz, is telemetered, processed and recorded on a wideband video recorder. The MSS data, consisting of 24 analog sensor outputs, is digitized and encoded as 15 megabit per second PCM. The MSS data is then transmitted as analog FM, demultiplexed, and recorded on a 25 channel recorder. It is shown that bit error rate is an excellent indicator of MSS link performance while signal-to-noise ratio and distortion vs frequency adequately define RBV link performance.

Pandelides, J.↗
NASA NTRS1974

Impact of scintillation of transionospheric communications

Analyses of AGC analog data from the Small Astronomy Satellite (SAS) at VHF (136 MHz) have shown amplitude fluctuations in the signals received at several equatorial tracking sites operated by NASA. Coincident digital telemetry data, transmitted from SAS at 1 kbps, has also been analyzed. Errors in data are shown to increase markedly for nighttime satellite passes around the periods of the two equinoxes as compared to the errors observed during other periods. This paper establishes the qualitative and quantitative correlations between the ionospheric scintillation phenomenon and the occurrence of errors. Strong time and geographic cause and effect relationships are established by determining the statistical correlation between scintillation indices and bit error rates.

Blank, H. A.↗
NASA NTRS1974

Development of a wideband pulse quaternary modulation system

Laboratory data verifying the pulse quaternary modulation (PQM) theoretical predictions is presented. The first laboratory PQM laser communication system was successfully fabricated, integrated, tested and demonstrated. System bit error rate tests were performed and, in general, indicated approximately a 2 db degradation from the theoretically predicted results. These tests indicated that no gross errors were made in the initial theoretical analysis of PQM. The relative ease with which the entire PQM laboratory system was integrated and tested indicates that PQM is a viable candidate modulation scheme for an operational 400 Mbps baseband laser communication system.

Federhofer, J. A.↗
NASA NTRS1974

Performance analysis of a frame sync algorithm for uncoded PSK telemetry

The optimum procedure for locating a frame sync word periodically inserted in uncoded binary data received over a binary symmetric channel is based on the Hamming distance metric. In this paper, a practical frame sync acquisition and maintenance algorithm is described, and its performance is analyzed. Specifically, with respect to this algorithm, an upper bound on the probability of false sync acquisition, the mean time to sync acquisition, and the subsequent mean time to loss of sync are computed for arbitrary bit error rates, frame lengths, sync word lengths, and algorithm parameters.

Levitt, B. K.↗