Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Transitional flight characteristics of a geometrically simplified STOVL model

The transitional flight characteristics of a geometrically simplified Short Take-Off Vertical Landing (STOVL) aircraft configuration were measured in the NASA Ames 7- by 10-Foot Wind Tunnel. The experiment was designed to provide detailed data for evaluating the capability of computational fluid dynamics methods to predict the important powered lift flow parameters. The model consists of a 60 deg cropped delta wing planform; a blended fuselage; and tandem, circular, high pressure air jets that exit perpendicular to the flat lower surface. Freestream Mach number is limited to a maximum 0.2. Model angle of attack ranges from -10 deg to +20 deg. The nozzle pressure ratios of both jets are varied between 1 and 3, and the jet exit temperatures are maintained at near ambient conditions. Detailed surface pressure measurements show that suction pressure peaks located on the upper surface of the wing during conventional wingborne flight for angles of attack greater than 5 deg move to the wing lower surface at angles of attack less than 0 deg. A reduction in these suction pressure peaks is observed when the lift jets are operating. With sonic jet exit conditions, a freestream Mach number of 0.14, and 0 deg angle of attack, the jet-induced suckdown is equivalent to a 3.7 deg reduction in angle of attack. Schlieren, laser light sheet flow visualization and total pressure measurements in the jet plumes provide a description of the three-dimensional jet efflux flowfield.

Roth, Karlin R.↗
NASA NTRS1994

Experimental studies of transonic flow field near a longitudinally slotted wind tunnel wall

The results of detailed parametric experiments are presented for the near-wall flow field of a longitudinally slotted transonic wind tunnel. Existing data are reevaluated and new data obtained in the Langley 6- by 19-inch Transonic Wind Tunnel are presented and analyzed. In the experiments, researchers systematically investigate many pertinent wall-geometry variables such as the wall openness and the number of slots along with the free stream Mach number and model angle of attack. Flow field surveys on the plane passing through the centerline of the slot were conducted and are presented. The effects of viscosity on the slot flow are considered in the analysis. The present experiments, combined with those of previous investigations, give a more complete physical characterization of the flow near and through the slotted wall of a transonic wind tunnel.

Everhart, Joel L.↗
NASA NTRS1955

Investigation in the Langley Free-Flight Tunnel of the Low-Speed Stability and Control Characteristics of a 1/10-Scale Model Simulating the Convair F-102A Airplane

An investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model simulating the Convair F-102A airplane has been made in the Langley free-flight tunnel. The model in its basic configuration and with two modifications involving leading- edge slats and an increase in vertical-tail size was flown through a lift-coefficient range from 0.7 to the stall. Only relatively low-altitude conditions were simulated. The longitudinal stability characteristics of the model were considered satisfactory for all conditions investigated. The lateral stability characteristics were considered satisfactory for the basic configuration over the lift-coefficient range investigated, except near the stall, where large values of static directional instability caused the model to be directionally divergent. An 80-percent increase in vertical-tail area increased the angle of attack at which the model became directionally divergent. The longitudinal and lateral control characteristics were generally satisfactory. Although the adverse sideslip characteristics for the model were considered acceptable over the angle-of-attack range, analysis indicates that the adverse sideslip characteristics of the airplane may be objectionable at high angles of attack.

Boisseau, Peter C.↗
NASA NTRS2006

Planar laser-induced fluorescence (PLIF) investigation of hypersonic flowfields in a Mach 10 wind tunnel

Planar laser-induced fluorescence (PLIF) of nitric oxide (NO) was used to visualize four different hypersonic flowfields in the NASA Langley Research Center 31-Inch Mach 10 Air wind tunnel. The four configurations were: (1) the wake flowfield of a fuselage-only X-33 lifting body, (2) flow over a flat plate containing a rectangular cavity, (3) flow over a 70deg blunted cone with a cylindrical afterbody, formerly studied by an AGARD working group, and (4) an Apollo-geometry entry capsule - relevant to the Crew Exploration Vehicle currently being developed by NASA. In all cases, NO was seeded into the flowfield through tubes inside or attached to the model sting and strut. PLIF was used to visualize the NO in the flowfield. In some cases pure NO was seeded into the flow while in other cases a 5% NO, 95% N2 mix was injected. Several parameters were varied including seeding method and location, seeding mass flow rate, model angle of attack and tunnel stagnation pressure, which varies the unit Reynolds number. The location of the laser sheet was as also varied to provide three dimensional flow information. Virtual Diagnostics Interface (ViDI) technology developed at NASA Langley was used to visualize the data sets in post processing. The measurements demonstrate some of the capabilities of the PLIF method for studying hypersonic flows.

Danehy, Paul M.↗
NASA NTRS2020

FLEET Velocimetry in the Common Research Model’s Wing Wake

Femtosecond laser electronic excitation tagging was used to make velocity measurements in the wake of the wing of the Common Research Model (CRM). Experiments were performed in the NASA Langley Research Center’s National Transonic Facility over a range of tunnel operating conditions. Pressures ranged from 205 to 411 kPa, temperatures from 278 to 323 K, and Mach from 0.1 to 0.9. Velocity was also determined over a range of model angles of attack. Time-averaged velocity results were obtained in both air and nitrogen, while single-shot velocity was obtained under certain tunnel operating conditions. Spatially-resolved, two dimensional, single component velocity measurements were achieved using a newly-developed laser scanning technique, which proved sufficiently sensitive to measure an approximately 5% velocity deficit in the wing wake region of the CRM.

Daniel T Reese↗
NASA NTRSDate not supplied

Implementation of an Unsteady PSP System in the NASA Transonic Dynamics Tunnel

An unsteady pressure-sensitive paint (uPSP) system has been developed to provide time-resolved pressure measurements in the NASA Langley Transonic Dynamics Tunnel (TDT). Obtaining these measurements necessitated the development of environmental enclosures to protect the high-speed camera and ultraviolet lights required for uPSP from the harsh environment present during tunnel operation. Since the facility main drive was non-functioning during the testing window, performance of the uPSP system was demonstrated using an impinging jet with a passive oscillator attachment to provide unsteady flow with a known frequency independent of amplitude. Measurements were obtained for tunnel pressures ranging from 565 to 2116 psf, and model angles of attack between -4 degrees and 4 degrees. Results indicate that the system is capable of measuring surface pressure differentials on the order of 0.01 psi at full scale with a camera frame rate of at least 10 kHz. Spectral analysis shows that the fundamental frequency of the oscillating jet is captured by the uPSP system, as are the second and third harmonics. Dynamic mode decomposition highlights the dominant coherent spatial structures of the surface pressure, along with the associated frequency and growth rate of each mode, allowing for a de-noised reconstruction of the uPSP measurements. The experimental campaign outlined within this report also confirmed compatibility of the uPSP system with the TDT facility data acquisition system, and verified the successful integration with existing processing capabilities within the NASA advanced supercomputing environment.

unsteady pressure-sensitive paint↗
NASA NTRSDate not supplied

Implementation of an Unsteady PSP System in the NASA Transonic Dynamics Tunnel

An unsteady pressure-sensitive paint (uPSP) system has been developed to provide time-resolved pressure measurements in the NASA Langley Transonic Dynamics Tunnel (TDT). Obtaining these measurements necessitated the development of environmental enclosures to protect the high-speed camera and ultraviolet lights required for uPSP from the harsh environment present during tunnel operation. Since the facility main drive was non-functioning during the testing window, performance of the uPSP system was demonstrated using an impinging jet with a passive oscillator attachment to provide unsteady flow with a known frequency independent of amplitude. Measurements were obtained for tunnel pressures ranging from 565 to 2116 psf, and model angles of attack between -4 degrees and 4 degrees. Results indicate that the system is capable of measuring surface pressure differentials on the order of 0.01 psi at full scale with a camera frame rate of at least 10 kHz. Spectral analysis shows that the fundamental frequency of the oscillating jet is captured by the uPSP system, as are the second and third harmonics. Dynamic mode decomposition highlights the dominant coherent spatial structures of the surface pressure, along with the associated frequency and growth rate of each mode, allowing for a de-noised reconstruction of the uPSP measurements. The experimental campaign outlined within this report also confirmed compatibility of the uPSP system with the TDT facility data acquisition system, and verified the successful integration with existing processing capabilities within the NASA advanced supercomputing environment.

unsteady pressure-sensitive paint↗
NASA NTRSDate not supplied

Implementation of an Unsteady PSP System in the NASA TDT

An unsteady pressure-sensitive paint (uPSP) system has been developed to provide time-resolved pressure measurements in the NASA Langley Transonic Dynamics Tunnel (TDT). Obtaining these measurements necessitated the development of environmental enclosures to protect the high-speed camera and ultraviolet lights required for uPSP from the harsh environment present during tunnel operation. Since the facility main drive was non-functioning during the testing window, performance of the uPSP system was demonstrated using an impinging jet with a passive oscillator attachment to provide unsteady flow with a known frequency independent of amplitude. Measurements were obtained for tunnel pressures ranging from 565 to 2116 psf, and model angles of attack between -4 degrees and 4 degrees. Results indicate that the system is capable of measuring surface pressure differentials on the order of 0.01 psi at full scale with a camera frame rate of at least 10 kHz. Spectral analysis shows that the fundamental frequency of the oscillating jet is captured by the uPSP system, as are the second and third harmonics. Dynamic mode decomposition highlights the dominant coherent spatial structures of the surface pressure, along with the associated frequency and growth rate of each mode, allowing for a de-noised reconstruction of the uPSP measurements. The experimental campaign outlined within this report also confirmed compatibility of the uPSP system with the TDT facility data acquisition system, and verified the successful integration with existing processing capabilities within the NASA advanced supercomputing environment. Note: this presentation is an MP4 video with sound, color with a run time of 10 minutes 37 seconds.

unsteady pressure-sensitive paint↗
NASA NTRS1986

Full-potential modeling of blade-vortex interactions

A comparison is made of four different models for predicting the unsteady loading induced by a vortex passing close to an airfoil. (1) The first model approximates the vortex effect as a change in the airfoil angle of attack. (2) The second model is related to the first but, instead of imposing only a constant velocity on the airfoil, the distributed effect of the vortex is computed and used. This is analogous to a lifting surface method. (3) The third model is to specify a branch cut discontinuity in the potential field. The vortex is modeled as a jump in potential across the branch cut, the edge of which represents the center of the vortex. (4) The fourth method models the vortex expressing the potential as the sum of a known potential due to the vortex and an unknown perturbation due to the airfoil. The purpose of the current study is to investigate the four vortex models described above and to determine their relative merits and suitability for use in large three-dimensional codes.

Jones, H. E.↗
NASA NTRS1986

Full potential modeling of blade-vortex interactions

A comparison is made of four different models for predicting the unsteady loading induced by a vortex passing close to an airfoil. (1) The first model approximates the vortex effect as a change in the airfoil angle of attack. (2) The second model is related to the first but, instead of imposing only a constant velocity on the airfoil, the distributed effect of the vortex is computed and used. This is analogous to a lifting surface method. (3) The third model is to specify a branch cut discontinuity in the potential field. The vortex is modeled as a jump in potential across the branch cut, the edge of which represents the center of the vortex. (4) The fourth method models the vortex expressing the potential as the sum of as known potential due to the vortex and an unknown perturbation due to the airfoil. The purpose of the current study is to investigate the four vortex models described above and to determine their relative merits and suitability for use in large three-dimensional codes.

Jones, H. E.↗
NASA NTRS1994

Propagation of experimental uncertainties from the tunnel to the body coordinate system in 3-D LDV flow field studies

An analysis of experimental laser Doppler velocimetry (LDV) data uncertainties that propagate from measurements in the tunnel coordinate system to results in the model system are provided. Calculations of uncertainties as functions of the variables that comprise the final result requires assessment of the contribution each variable makes. Such an analysis enables and necessitates the experimentalists to identify and address the contributing error sources in the experimental measurement system. This provides an opportunity to improve the quality of data derived from experimental systems. This is especially important in experiments where small changes in test conditions are expected to produce small, detectable changes in results. In addition, the need for high-quality experimental data for CFD method validation demands a thorough assessment of experimental uncertainty. Transforming from one Cartesian coordinate system to another by three sequential rotations, equations were developed to transform the variables initially obtained in the original coordinates into variables in the final coordinate system. Based on the transformation equations, propagation equations for errors in the experimentally-derived flow quantities were derived for a model at angle of attack. Experimental uncertainties were then propagated from the tunnel coordinate system into the model system.

Neuhart, Dan H.↗
NASA NTRS1981

Experimental investigation of vortices shed by various wing fin configurations

Forty-six different fins, which were members of twelve plan-form families, were tested. A two dimensional Boeing single element airfoil at an angle of attack of eight degrees and a sweepback angle of thirty-two was used to simulate a portion of the wing of a generator aircraft. Various free stream velocities were used to test any individual fin at its particular angle of attack. While the fin itself was mounted on the upper surface of the generator model, the angle of attack of each fin was varied until stall was reached and/or passed. The relative fin vortex strengths were measured in two ways. First, the maximum angular velocity of a four blade rotor placed in the fin vortex center was measured with the use of a stroboscope. Second, the maximum rolling moment on a following wing model placed in the fin vortex center was measured by a force balance.

Iversen, J.↗
NASA NTRS1992

SiO(X) coatings for atomic oxygen protection of polyimide Kapton in low earth orbit

Sputter-deposited SiO(X) (where X between 1.9 and 2.0) thin film coatings have been found to be durable to atomic oxygen. Such coatings will be used to protect polyimide Kapton photovoltaic array blankets from atomic oxygen attack in low earth orbit (LEO) on the Space Station Freedom (SSF). Monte Carlo modeling of atomic oxygen attack at defect sites in protected Kapton exposed in laboratory RF plasma ashers and on solar tracking photovoltaic arrays in space has been conducted to enable understanding of degradation processes relevant to the durability of the SSF solar array blanket. SiO(X) protective coating performance data from RF plasma asher tests will be presented, along with Monte Carlo modeling considerations, to enable the projection of in-space durability of the SSF solar array blankets based on ground laboratory test results.

Banks, Bruce A.↗
NASA NTRS1990

Finite element model reduction application to parametric studies and optimization of rotorcraft structures

As a result of this work, a reduction procedure has been developed which can be applied to large finite element model of airframe type structures. This procedure, which is tailored to be used with MSC/NASTRAN finite element code, is applied to the full airframe dynamic finite element model of AH-64A Attack Helicopter. The applicability of the resulting reduced model to parametric and optimization studies is examined. Through application of the design sensitivity analysis, the viability and efficiency of this reduction technique has been demonstrated in a vibration reduction study.

Hashemi-Kia, M.↗
NASA NTRSDate not supplied

Characterization of Radiative Heating Anomaly in High Enthalpy Shock Tunnels

Surface heating measurements in shock tunnels operating at high enthalpy have previously showed anomalously high heating, the mechanisms for which have been the subject of much speculation. However, recent tests in JAXA’s High Enthalpy Shock Tunnel (HIEST) have presented compelling evidence that the heating anomaly is due to radiation from the shock layer, produced by impurities within the shock. This paper describes a test series performed with an Apollo capsule model at angle of attack. The purpose of the test is nominally to study transition over the capsule model at high enthalpy, however data is confounded by the presence of this radiative heating. The model is thus instrumented with thermocouple heat flux gauges and spectrometer-coupled fiber optics to characterize the spectrum of radiative heating simultaneous to the heat flux measurements. Analyses of the spectra, estimates of radiative heating corrections, and comparison to computational fluid dynamic simulation of the shock tunnel are presented.

Brett A Cruden↗
NASA NTRS1958

Wind-Tunnel Investigation of Some Effects of Wing Sweep and Horizontal-Tail Height on the Static Stability of an Airplane Model at Transonic Speeds

A research model of an airplane with a configuration suitable for supersonic flight was tested at transonic speeds in order to establish the effects on longitudinal and lateral stability of certain changes in both wing sweep and height of the horizontal tail. Two wings of aspect ratio 3 and taper ratio 0.15, one having the quarter-chord line swept back 30 deg and the other 45 deg, were each tested with the horizontal tail of the model in a low and in a high position. One configuration was also tested with fuselage strakes. The tests were made at Mach numbers from 0.60 to 1.17 and Reynolds numbers from 1.9 x 10(exp 6) to 2.6 x 10(exp 6). The results indicated that a low horizontal-tail position (below the wing-chord plane) gave positive longitudinal stability for the model for all angles of attack used (angles of attack up to 24 deg); whereas, a higher tail position (above the wing-chord plane) resulted in a large reduction in stability at moderate angles of attack. With the higher horizontal tail, the 30 deg-swept-wing model had somewhat more stability than the 45 deg-swept-wing model at subsonic Mach numbers. With the lower tail, the 45 deg-swept-wing model had slightly more stability at all Mach numbers. The model with the 30 deg swept wing had greater directional stability with the tail in the higher rather than the lower position, but the opposite was true for the 45 deg-swept-wing model. The directional stability decreased sharply at high angles of attack; this characteristic was alleviated by the use of fuselage strakes which, however, proved to be detrimental to the longitudinal stability of the model tested.

Fisher, Lewis R.↗
NASA NTRS1984

Aerodynamic characteristics of two general aviation canard configurations at high angles of attack

The results of wind tunnel tests of two propeller driven canard general aviation aircraft models at high angles of attack are reported. Both tractor and pusher prop configurations were examined. Angles of attack of -6 to 40 deg were used with the pusher model at Re of 1,600,000, and from -30 to 90 deg and Re of 550,000 for the tractor model. The tests showed that the canard would stall long before the wing and produce a nose-down tendency, thus effectively keeping the aircraft out of the stall regime. However, a sequence of pilot actions or design factors such as the airfoils, relative geometry of the canard and wing, the propeller location and the center of gravity location could introduce a wide variance in stall characteristics from one aircraft to another.

Chambers, J. R.↗