Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “agglomeration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A comparative study between real-world and laboratory accelerated aging of Cu/SSZ-13 SCR catalysts

Elucidating aging mechanisms in real-world applications is a critical component for developing and maintaining Cu/SSZ-13 SCR catalysts. To reveal gaps between laboratory accelerated aging and real-world aging, herein we report thorough comparative studies between 6 representative catalysts. Here, we apply a wide range of catalyst characterization methods, including surface area/porosity analysis, X-ray diffraction (XRD), H 2 -temperature programmed reduction, NH3-temperaure programmed desorption, solid-state nuclear magnetic resonance (NMR), in situ X-ray photoelectron (XPS) and electron paramagnetic resonance (EPR) spectroscopies, to gain atomic-level knowledge on Cu transformation under different aging protocols. We then correlate such knowledge to SCR, NH 3 /NO oxidation kinetic behavior of the catalysts. We found that sulfur aging plays the most important role in interpreting catalyst degradation during real-world application, including direct sulfur poisoning of isolated Cu II SCR active species to CuSO 4 -like species, the agglomeration of such species to multinuclear CuSO 4 clusters, and eventually, CuO formation during desulfation treatments. Such chemistries convert SCR active Cu to SCR inert Cu moieties without severely deteriorating catalyst support integrity. These characteristics are partially replicated by hydrothermal aging in the presence of SOx but are poorly mimicked by hydrothermal aging alone.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of CuFeMnAlO 4+δ oxygen carrier with high attrition resistance and 50-kWth methane/air chemical looping combustion tests

A Copper-Ferri-Manganese-Aluminate spinel (CuFeMnAlO 4+δ ) oxygen carrier, developed at the US Department of Energy’s (DOE) National Energy Technology Laboratory (NETL), shows promising results for chemical looping combustion with methane. Attrition resistance of the spinel oxygen carrier (160–600 µm) produced by a wet agglomeration method was significantly higher than that observed previously with a Copper-Ferri-Aluminate (CuFeAlO 4 ) oxygen carrier. Improved attrition resistance of the novel carrier can be attributed to minimal alumina phase segregation and minimal carbon formation. Heats of reaction measured by differential scanning calorimetry indicated exothermicity during reduction with methane. The total oxygen transfer capacity of the material was about 10.5 wt% at 850 °C. The attrition resistance and the oxygen transfer capacity of the carrier prepared at a commercial manufacturing facility (180 kg) were very similar to observed values during the development phase with the lab scale preparations. The material displays satisfactory methane conversion and significantly high particle durability during a 54 h test campaign conducted in NETL’s 50-kWth chemical looping dual fluid bed reactor unit at temperatures ranging from 700 to 900 °C. Low oxygen carrier make-up cost, due to the use of natural ore and pigment grade raw materials during synthesis and very low attrition rates, exceeded the performance goals determined by systems studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Enhanced flexibility and thermal conductivity of HfC decorated carbon nanofiber mats

Future-generation spacecraft components allude discovery of novel materials that can withstand extreme environments (>2000 °C). The combined effect of ultra-high temperature ceramics (UHTCs) and carbon fibers (C f ) can satisfy the demanding requirements of aerospace applications. A novel, hybrid, and flexible hafnium carbide (HfC)-decorated carbon nanofiber (C nf ) mat was fabricated via electrospinning. Enhanced thermal stability of the flexible HfC decorated C nf over C nf can be elucidated from the 20-fold increment in thermal conductivity and the onset of degradation at higher temperatures (840 °C). Successful integration of multi-layered sandwich lattice using in-housed fabricated HfC decorated C nf showed retention of the fibrous structure even after extreme spark plasma sintering (SPS) process at 1850 °C. Fabricating a similar multi-layered structure using procured C f was unsuccessful due to bundled agglomeration and micron-sized fibers. High-load indentation suggests that HfC decorated C nf interlayer is stronger (~2.3 times) than the parent UHTC with no cracking at the interface. Compared with the HfC matrix, the indentation-damaged area at the interface reduced up to ~56% due to toughening mechanisms such as C nf , fiber pull-out and bridging. The synthesized HfC decorated Cnf mat is proposed as an ultra-thin filler material for joining similar or dissimilar UHTCs while maintaining similar chemistry and better mechanical integrity at the interface. Furthermore, the findings insinuate a new paradigm in designing hybrid and flexible ceramic-containing materials for thermal protection systems (TPS) of future-generation spacecraft components that can mitigate failure in extreme environments (>2000 °C).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fe doped aluminoborate PKU-1 catalysts for the ketalization of glycerol to solketal: Unveiling the effects of iron composition and boron

An inexpensive Fe doped aluminoborate consisted of 18% Fe in PKU-1 material that exhibits high selectivity of 4-hydroxymethy-2,2-dimethyl-1,3-dioxolane (Solketal, 98.3%), considerable activity (TOF 51.7 h -1 ), and recyclable ability in the ketalization of glycerol to Solketal with acetone at 318 K has been developed. Here our study demonstrated that the structure of Fe (less agglomerated iron species vs. FeO x clusters) can be tuned by changing Fe loading in the PKU-1 material, which correlated well with experimental observations. Furthermore, the surface boron sites were promoted by iron loading and behaved as Lewis-acid sites to facilitate the reaction process of glycerol ketalization, while the Solketal selectivity was closely related with the structure of iron species in PKU-1, which was proved by kinetic studies, density function theory (DFT) calculations, and a series of spectroscopy studies. This investigation demonstrates that the surface B sites can play important roles in the reaction instead of being spectators.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The effect of silica oxide support on the catalytic activity of nickel-molybdenum bimetallic catalyst toward ethanol steam reforming for hydrogen production

This work investigates the effects of molybdenum promoter and silica oxide (SiO 2 ) support morphology on the ethanol steam reforming (ESR) performance of Nickel-Molybdenum (NiMo) bimetallic catalysts. Ordered mesoporous SiO 2 (SBA-15) and commercial SiO 2 supports were used as the oxide support materials. The synthesized catalysts were prepared via the wet impregnation method and characterized via XRD, H 2 -TPR, BET, FTIR, and Raman techniques. This study shows that NiMo bimetallic catalyst supported on SBA-15 has superior catalytic activity and better coking resistance at an intermediate temperature of 600 ⁰C than commercial SiO 2 supported catalysts. The presence of a uniform mesoporous structure of SBA-15 with an average pore diameter of ~ 2 nm can obstruct the carbon formation, leading to improved coking resistance. The catalytic enhancement of NiMo bimetallic catalysts toward ESR can also be linked to the ability of Mo promoter in enhancing the interaction between NiMo nanoparticles and SiO 2 support materials and restraining agglomeration of Ni nanoparticles, which results in further improvement of NiMo nanoparticle dispersion and inhibit its sintering. The NiMo bimetallic catalysts supported on SBA-15 illustrated the high H 2 yield of ~ 54% and carbon conversion of ~ 89% with the excellent stability for ESR performed at 600 ⁰C and the steam-to-carbon ratio of 2 over 65 hours.

25 ENERGY STORAGE↗
DOE OSTI2025

Sizing comingled CF/PA 6 fibers with cellulose nanofibrils for enhanced performance properties

Compatibility between the reinforcing phase and the polymer matrix is critical to achieving the desired mechanical and thermal performance of composite materials. Several mechanisms can enhance this interfacial interaction, including surface treatments (e.g., oxidation, plasma, or irradiation), in-situ nanoparticle deposition, and fiber sizing. Here, in this study, cellulose nanofibrils (CNF) were employed as a sustainable sizing agent to modify the interface in commingled carbon fiber (CF)/polyamide 6 (PA 6) yarns, in which CF and PA6 filaments are intimately blended to enable simultaneous consolidation. A 0.25 wt% CNF aqueous suspension was applied under bath sonication to ensure uniform dispersion and minimize agglomeration. CNF-sized and unsized yarns were used to fabricate unidirectional composite plates via filament winding on a flat mandrel, followed by compression molding. Scanning electron microscopy confirmed CNF presence on both CF and PA6 filaments. CNF-sized composites exhibited increments in interlaminar shear strength (ILSS) by 50%, flexural strength by 11%, and tensile strength by 2.5% compared to unsized composites. Thermal analysis showed minimal changes in degradation temperature and crystallinity. These findings demonstrate that CNF sizing enhances interfacial bonding and mechanical performance, offering a scalable and environmentally friendly strategy for thermoplastic composite manufacturing along with yarn/tow handleability.

Cellulose nanofibrils (CNF)↗
DOE OSTI2023

Biologically inspired reinforcement using polydopamine of polymer bound composites

Interfacial strength plays a critical role in the mechanical properties of a composite system. In this work, a proven mock high explosive (HE), 5-iodo-2’-deoxyuridine (IDOX) was coated by the adhesive promoting polymer polydopamine (PDA), then formulated with an Estane binder system to form an improved HE mock composite. An extensive comparison study of mechanical properties was performed to determine the effects, if any, of PDA on the composite system. To aid in interpretation of the mechanical test data, neutron reflectometry experiments were performed to determine the thickness and structure of the as deposited PDA films. The mechanical performance of PDA-treated IDOX was then compared to untreated specimens by compression testing in the Brazilian disk geometry. The results strongly suggested that the structure of PDA consists of two layers: one low in density caused by polymer agglomerates attaching to the substrate during polymerization, and the second high in density caused by controlled linear deposition of polydopamine. Finally, the mechanical testing showed that PDA greatly increased the stiffness and yield strength of IDOX based mocks without causing any disruption to the underlying crystal system.

42 ENGINEERING↗
DOE OSTI2021

Enabling aqueous processing for LiNi 0.80 Co 0.15 Al 0.05 O 2 (NCA)-based lithium-ion battery cathodes using polyacrylic acid

Replacing N-methyl-2-pyrrolidone (NMP) with water in the production of lithium-ion battery cathodes is critical to realizing process cost savings and improved worker safety. LiNi 0.80 Co 0.15 Al 0.05 O 2 (NCA) is a poor fit for aqueous processing due to destructive Al current collector corrosion resulting from highly basic slurries and detrimental surface reconstruction reactions that occur in water. In this study, polyacrylic acid (PAA, MW = 450,000 g·mol -1 ) is examined as a corrosion-mitigating and surface-stabilizing agent. Adding PAA to an aqueous NCA slurry can provide a stable pH (4.0–8.5) for at least 4 h, since the carboxyl groups from PAA dissociate and increase the proton concentration in the slurry. Further, these groups can also adsorb to the surface of NCA particles and provide electrostatic stability from active material particle agglomeration, as revealed by zeta potential measurements. Minor cracking does occur at the electrode surface; this cracking likely caused poorer adhesion to the Al current collector in the aqueous-processed film when compared to the NMP-processed baseline. Electrochemically, the leached Li does cause a lower initial capacity for the aqueous-processed cathode, though the capacity retention of the aqueous-processed cathode is better than the baseline. The cracks in the coating led to a rise in charge transfer resistance that hindered rate capability above 1C.

25 ENERGY STORAGE↗
DOE OSTI2023

Simultaneous Single Crystal Growth and Segregation of Ni-Rich Cathode Enabled by Nanoscale Phase Separation for Advanced Lithium-Ion Batteries

Here, a novel nanoscale phase separation process has been discovered to promote the growth and segregation of single-crystal LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811). This process occurs directly during high-temperature calcination without significant agglomeration. The key lies in converting transition metal hydroxide (TM(OH) 2 ) precursors with well-controlled morphology into transition metal oxide (TMO) intermediates before reacting them with lithium salt. The nanoscale redistribution of Ni in TMO, resulting from the concurrent formation of spinel and rock salt phases, helps to deagglomerate the clusters of later-formed NMC811 crystals. The as-prepared single-crystal NMC811 is further validated in a 2Ah pouch cell, demonstrating 1,000 stable cycles. The fundamentally new reaction mechanism of single-crystal growth and segregation provides a new direction for large-scale synthesis of a broad range of single crystals for advanced energy storage.

25 ENERGY STORAGE↗
DOE OSTI2022

Fuel property impacts on gaseous and PM emissions from a multi-mode single-cylinder engine

The U.S. Department of Energy’s Co-Optima initiative has focused on improving fuel economy and vehicle performance while reducing emissions through the simultaneous development of emerging sustainable fuels with beneficial properties and advanced combustion strategies. A major thrust has been the development of advanced compression ignition (ACI) combustion strategies of gasoline range fuels in combination with spark-ignited (SI) combustion in a single engine capable of multi-mode operation to achieve high power density with enhanced part load efficiency. The aim of this study was to further the understanding of how emissions from both ACI and SI strategies operating on the same fuels in the same engine are impacted by different fuel properties. This investigation focused on particulate matter (PM) and gaseous hydrocarbon emissions from 6 different fuels across 3 different combustion modes on the same single-cylinder engine designed for multi-mode operation: SI combustion, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). In each of these modes, 3 different CA50 phasings were studied such that all 6 fuels could be studied at the same phasings. Three of the six different fuels used were specially formulated in a previous investigation to study the impact of fuel distillation and aromatic content while maintaining the research octane number (RON) and octane sensitivity. Additionally, neat isooctane and two ethanol containing fuels (RD5-87 and Co-Optima E30) were studied. Different fuel and phasing impacts on emissions were observed across the three combustion modes. Fuel properties were found to impact soot PM and particle number more than the CA50 phasing, while the phasing had more impact on NOx emissions. The NOx emissions were reduced in the PFS mode for all fuels compared to SI combustion, but the SACI combustion mode did not reduce NOx emissions. Although PFS produced low soot PM emissions like SI, total PM mass emissions were significantly higher due to large organic carbon (OC) PM mass contribution. Both PFS and SACI had greater particle number emission than SI operation with small nuclei mode particles dominating in PFS compared to large agglomeration particles in SACI.

42 ENGINEERING↗
DOE OSTI2022

Evaluation of the energy balance of chemical looping combustion of solid fuels using CuO-based oxygen carriers

Chemical looping combustion (CLC) can inherently capture the CO2 generated during thermal energy production. When using CuO-based oxygen carriers, the reactions in both the fuel reactor (FR) and air reactor (AR) are exothermic, facilitating autothermal operation. To prevent the oxygen carrier from becoming agglomerated while ensuring a sufficient oxygen release rate, it is necessary to predict the FR temperature and remove an appropriate amount of heat from the AR when burning high-rank fuels. Here in this work, the energy balance of a CuO-based CLC system firing various solid fuels (biomass, coal, and petroleum coke) was investigated by establishing a thermodynamic model using FactSage. The energy distribution characteristics of the FR were quantified based on a virtual five-step thermodynamic sequence. The effects of fuel properties, oxygen carrier properties, and operating conditions on the energy balance were evaluated systematically. The results indicate that the temperature difference between the FR and AR is not very sensitive to the heating value of the fuel, while the CuO loading of the oxygen carrier, the heat capacity of the support material, and the flow rate of the fluidizing gas have significant impact. The insights obtained in this work will help improve the design and heat management of CLC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Annealing temperature variation and its influence on the self-cleaning properties of TiO 2 thin films

Titanium dioxide (TiO 2 ) is an important material in science and engineering because of its basic and synthetic properties. Nevertheless, there is a dearth of reports in the open literature focusing on its ability to self-clean under temperature changes. In this study, we used the spin coating technique to produce TiO 2 thin films to evaluate its self-cleaning ability after annealing at different temperatures. The TiO 2 sol was obtained through an endothermal sol-gel process, and the gel was coated on a glass substrate using a spin coater. The deposited films were then annealed at 400 °C, 600 °C, and 800 °C for 1 h. The influence of annealing temperature variation on the self-cleaning properties of the thin film was characterized using X-ray diffraction, scanning electron microscope; Fourier transformed infrared spectrometric analysis and UV-vis spectrophotometer. A test to ascertain self-cleaning was conducted using the degradation of methylene blue, and the different films were tested for durability. The durability test confirmed the connection between solid coating and substrate at all annealing temperatures. Thin films annealed at 600 °C revealed the best self-cleaning properties. The morphological analysis revealed snowflake shapes uniformly distributed over the substrate at 400 °C, and agglomeration improved as the annealing temperature increased. Structural analysis showed an increase in crystallinity with an increase in annealing temperature for both rutile and anatase phases. At three different temperatures, the chemical bond and the absorption band pattern followed the same path, although the peak intensity declined with temperature rise. Finally, the optical bandgap of the thin coated TiO 2 declined from 3.39 eV to 3.20 eV as the binding temperature increased from 400 to 800 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes

A major factor driving fuel cell costs is the quantity of precious metal required. Therefore, it is important to understand a timeframe where inks can be reused. Here, in this work, we explore differences between a freshly prepared catalyst ink and one that has been stored for over a year – comparing ink properties, cathode catalyst layer microstructure, and their respective fuel cell performance. Ink studies revealed smaller agglomerate sizes and a decrease in shear viscosity for the aged ink. Longer storage time also results in fewer cracks and a more uniform ionomer distribution, as evidenced by microscopy characterization of rod-coated electrodes. Lastly, polarization curves show improved performance at higher current densities for the electrode prepared from the aged ink. We rationalize such effect in terms of enhanced ionomer adsorption onto the catalyst over time.

08 HYDROGEN↗
DOE OSTI2022

Sinter formation during directed energy deposition of titanium alloy powders

During directed energy deposition (DED) additive manufacturing, powder agglomeration and sintering can occur outside of the melt pool when using titanium alloy powders. Using in situ synchrotron radiography we investigate the mechanisms by which sintering of Ti6242 powder occurs around the pool, performing a parametric study to determine the influence of laser power and stage traverse speed on sinter build-up. The results reveal that detrimental sinter can be reduced using a high laser power or increased stage traverse speed, although the latter also reduces deposition layer thickness. The mechanism of sinter formation during DED was determined to be in-flight heating of the powder particles in the laser beam. Calculations of particle heating under the processing conditions explored in this study confirm that powder particles can reasonably exceed 700 °C, the threshold for Ti surface oxide dissolution, and thus the powder is prone to sintering if not incorporated into the melt pool. The build-up of sinter powder layer on deposit surfaces led to lack of fusion pores. To mitigate sinter formation and its detrimental effects on DED component quality, it is essential that the powder delivery spot area is smaller than the melt pool, ensuring most powder lands in the melt pool.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Revealing mechanisms of processing defect mitigation in laser powder bed fusion via shaped beams using high-speed X-ray imaging

The laser powder bed fusion (LPBF) process utilizing a focused Gaussian-shaped beam faces challenges, including pore formation, melt pool fluctuation and liquid spattering. While beam shaping technology has been explored as a potential approach for defect mitigation, the beam-matter interaction dynamics during melting with shaped beams remain unclear. Here, we report the direct observation of ring-shaped beam-matter interaction dynamics, including pore formation, melt pool fluctuation and liquid spattering, and unveil defect mitigation mechanisms in ring-shaped beam laser powder bed fusion process. Here, we find that, by spatially manipulating incident laser rays, the ring-shaped beam controls keyhole morphology, thereby managing the distribution of the reflected rays. This manipulation can effectively eliminate the formation of an unstable cavity at the keyhole tip, stabilizing the keyhole and mitigating keyhole pores. This enhanced keyhole stability effectively reduces the melt pool fluctuation, the formation of liquid breakup induced spatters and liquid droplet colliding induced large spatters in the laser powder bed fusion process. Additionally, the high-energy forefront of the ring-shaped beam effectively melts the powder bed, reducing agglomeration liquid spatter in the laser powder bed fusion process. The discovered defect mitigation mechanisms may guide the design of beam shaping strategies for simultaneously increasing the quality and productivity of metal additive manufacturing.

Beam shaping↗
DOE OSTI2022

Switching from batch to continuous granulation: A case study of metoprolol succinate ER tablets

Continuous manufacturing (CM) has been used to produce several immediate release drug products. No extended-release (ER) product manufactured employing CM technology has been approved yet. Herein this study investigated the critical aspects of switching from the batch mode of high shear granulation to the continuous operation of twin-screw granulation for extended-release tablets. Metoprolol succinate ER tablets was used as a model ER formulation for this purpose. A central composite design (CCD) was employed to determine the effects of high shear granulator (HSG) parameters, namely impeller speed, granulation time, and binder liquid feeding rate, on the critical granulation characteristics important for product performance. These critical granulation characteristics served as a guide for switching from the batch processing to the continuous operation for achieving the same breaking strength and dissolution for this ER metoprolol tablets. The granulation time was the most critical factor affecting the bulk properties of granules which contributed to tablet dissolution. The higher density and lower compressibility of granules were attained at the longest granulation time of 5.4 min with the fastest liquid feeding rate of 75 g/min. The granules’ density was the primary factor negatively affecting the dissolution of metoprolol tablets. However, the breaking strength of tablets confounded the effect of granules density on metoprolol dissolution. Switching the processing parameters of high shear granulation to twin-screw granulation achieved similar dissolution profiles (F2 greater than 50). The screw speed was not found to affect bulk properties of granules. The root cause of granulation failures in twin-screw granulation, such as premature consolidation, excessive swelling, poor cohesion, inconsistent shearing effects, and formation of deformed agglomerates, were identified. In conclusion, the use of critical granulation characteristics through a performance-based approach of ER tablets facilitated the switching of manufacturing of an ER formulation form batch to continuous operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Minimizing particle aggregation in Sm 2 Fe 17 N 3 powders: A CaO-assisted reduction-diffusion approach

We report a novel synthesis of Sm 2 Fe 17 N 3 powders using a CaO-assisted reduction-diffusion (RD) approach. CaO plays a crucial role during mechanochemical processing – acting both as a dispersant and a surface coating agent, which helps to prevent agglomeration due to sintering of Sm 2 Fe 17 particles during the RD step. Together with the added dispersant, the CaO by-product formed during RD can be easily removed in the washing step resulting in fewer aggregated Sm 2 Fe 17 N 3 particles and lower oxygen contamination in the final product. The impact of varying CaO amounts was examined, and synthesis conditions were optimized to achieve phase-pure Sm 2 Fe 17 N 3 powders with less aggregation of magnetic particles. The powders synthesized with addition of 1 wt% CaO as dispersant exhibited the highest hard-magnetic properties: a coercivity (H c ) of 10.7 kOe and a maximum energy product ((BH) max ) of 17.3 MGOe. By densifying the Sm 2 Fe 17 N 3 powders using high-pressure spark plasma sintering, a bulk magnet with a (BH) max of 21.1 MGOe with 88 % of theoretical density was produced. In conclusion, reducing aggregation of the Sm 2 Fe 17 N 3 increases coercivity and remanence of these magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Decomposition of PVDF to delaminate cathode materials from end-of-life lithium-ion battery cathodes

The growing demand of electric vehicles and rapid consumption of rechargeable lithium-ion batteries (LIBs) require recycling of spent cathode active materials (CAMs) to reduce hazardous wastes and supply raw materials to LIB production. To separate CAMs from the cathode, direct calcination of polyvinylidene fluoride (PVDF) binder is widely applied, which leads to high energy consumption and release of toxic hydrogen fluoride. It is desirable to have an environmentally friendly and effective alternative to traditional direct calcination. In this study, five lithium salts, LiOAc (lithium acetate), LiNO 3 , LiCl, Li 2 CO 3 , and Li 2 SO 4 , were deployed and compared for their performance in recycling CAMs. A peel-off efficiency of up to 98.5% was achieved at a LiOAc to LiNO 3 molar ratio of 3:2, salt to cathode mass ratio of 10:1, and temperature of 300 °C at a holding time of 30 min. This system avoids corrosive chemicals and minimizes particle agglomeration of recycled products. Compared with sodium salt systems (NaOAc-NaNO 3 ) or direct calcination, the LiOAc-LiNO 3 system prevented high reaction temperature or further lithium loss and minimized crystal structure and morphological changes. In conclusion, a decomposition mechanism of PVDF through adsorption of HF and fluorine substitution was proposed.

25 ENERGY STORAGE↗