Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Youngs Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

AGC-4 Specimen Post-Irradiation Examination Data Interim Report

This interim report documents preliminary results of the post-irradiation examination material property testing from the fourth advanced graphite creep (AGC), AGC 4, capsule specimens. This is the fourth of a series of six irradiation test trains planned as part of the AGC experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphite grades to moderate dose levels (=7 dpa). The AGC 4 capsule was irradiated in the Idaho National Laboratory Advanced Test Reactor at a nominal temperature of 800°C and to a peak dose of 8 dpa. Half of the AGC-4 specimens were subjected to compressive stresses to induce irradiation creep. Post-irradiation testing and measurement results are reported with the exception of thermal testing, which is still in progress, and irradiation mechanical strength testing. Additionally, some specimens initially deemed too hot to be examined in the ART Graphite laboratory may still be measured. The data reported includes specimen dimensions for both stressed and unstressed specimens to establish the irradiation creep rates, mass and dimensional data necessary to derive density, elastic constants (Young?s modulus, shear modulus, and Poisson?s ratio) from ultrasonic time of flight velocity measurements, Young?s modulus from the fundamental frequency of vibration, and electrical resistivity. A more complete evaluation of trends in the material property changes, as well as irradiation-induced creep due to the irradiation environment and applied load on the specimens, will be discussed later in AGC 4 post-irradiation examination analysis reports.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

AGC-4 Specimen Post-Irradiation Examination Data Interim Report

This interim report documents preliminary results of the post-irradiation examination material property testing from the fourth advanced graphite creep (AGC), AGC 4, capsule specimens. This is the fourth of a series of six irradiation test trains planned as part of the AGC experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphite grades to moderate dose levels (=7 dpa). The AGC 4 capsule was irradiated in the Idaho National Laboratory Advanced Test Reactor at a nominal temperature of 800°C and to a peak dose of 8 dpa. Half of the AGC-4 specimens were subjected to compressive stresses to induce irradiation creep. Post-irradiation testing and measurement results are reported with the exception of thermal testing, which is still in progress, and irradiation mechanical strength testing. Additionally, some specimens initially deemed too hot to be examined in the ART Graphite laboratory may still be measured. The data reported includes specimen dimensions for both stressed and unstressed specimens to establish the irradiation creep rates, mass and dimensional data necessary to derive density, elastic constants (Young?s modulus, shear modulus, and Poisson?s ratio) from ultrasonic time of flight velocity measurements, Young?s modulus from the fundamental frequency of vibration, and electrical resistivity. A more complete evaluation of trends in the material property changes, as well as irradiation-induced creep due to the irradiation environment and applied load on the specimens, will be discussed later in AGC 4 post-irradiation examination analysis reports.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Electronic, elastic, and optical properties of monolayer BC{sub 2}N

The structural stability, electronic structure, elasticity, and optical properties of four types of monolayer BC{sub 2}N have been investigated from first principles using calculation based on density functional theory. The results show that the structural stability of BC{sub 2}N increases with the number of C–C and B–N bonds. By calculating the two-dimensional Young's modulus, shear modulus, Poisson's ratio, and shear anisotropic factors in different directions, four structures present various anisotropies and the most stable structure is almost isotropic. For C-type BC{sub 2}N, the values of two-dimensional Young's modulus, shear modulus, and bulk modulus (309, 128, 195 GPa m{sup −1}), are smaller than those of graphene (343, 151, 208) but bigger than those of h-BN (286, 185, 116). Furthermore, the dielectric function, refractive index, reflectivity, absorption coefficient, and energy loss spectrum are also calculated to investigate the mechanism underpinning the optical transitions in BC{sub 2}N, revealing monolayer BC{sub 2}N as a candidate window material. - Graphical abstract: Schematic diagram of BC{sub 2}N under the biaxial tensile strain. Changes in the valence-band top and the conduction-band bottom of BC{sub 2}N with increasing strain.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Ultrahigh Elastic Strain Energy Storage in Metal-Oxide-Infiltrated Patterned Hybrid Polymer Nanocomposites

Modulus of resilience, the measure of a material’s capacity to store and release elastic strain energy, is critical for realizing advanced mechanical actuation technologies in micro/nanoelectromechanical systems. In general, engineering the modulus of resilience is difficult because it requires asymmetrically increasing yield strength and Young’s modulus against their mutual scaling behavior. This task becomes further challenging if it needs to be carried out at the nanometer scale. Here, we demonstrate organic–inorganic hybrid composite nanopillars with one of the highest modulus of resilience per density by utilizing vapor-phase aluminum oxide infiltration in lithographically patterned negative photoresist SU-8. In situ nanomechanical measurements reveal a metal-like high yield strength (~500 MPa) with an unusually low, foam-like Young’s modulus (~7 GPa), a unique pairing that yields ultrahigh modulus of resilience, reaching up to ~24 MJ/m 3 as well as exceptional modulus of resilience per density of ~13.4 kJ/kg, surpassing those of most engineering materials. The hybrid polymer nanocomposite features lightweight, ultrahigh tunable modulus of resilience and versatile nanoscale lithographic patternability with potential for application as nanomechanical components which require ultrahigh mechanical resilience and strength.

36 MATERIALS SCIENCE↗
DOE OSTI2014

A synthetic mechano-growth factor E peptide promotes rat tenocyte migration by lessening cell stiffness and increasing F-actin formation via the FAK-ERK1/2 signaling pathway

Tendon injuries are common in sports and are frequent reasons for orthopedic consultations. The management of damaged tendons is one of the most challenging problems in orthopedics. Mechano-growth factor (MGF), a recently discovered growth repair factor, plays positive roles in tissue repair through the improvement of cell proliferation and migration and the protection of cells against injury-induced apoptosis. However, it remains unclear whether MGF has the potential to accelerate tendon repair. We used a scratch wound assay in this study to demonstrate that MGF-C25E (a synthetic mechano-growth factor E peptide) promotes the migration of rat tenocytes and that this promotion is accompanied by an elevation in the expression of the following signaling molecules: focal adhesion kinase (FAK) and extracellular signal regulated kinase1/2 (ERK1/2). Inhibitors of the FAK and ERK1/2 pathways inhibited the MGF-C25E-induced tenocyte migration, indicating that MGF-C25E promotes tenocyte migration through the FAK-ERK1/2 signaling pathway. The analysis of the mechanical properties showed that the Young's modulus of tenocytes was decreased through treatment of MGF-C25E, and an obvious formation of pseudopodia and F-actin was observed in MGF-C25E-treated tenocytes. The inhibition of the FAK or ERK1/2 signals restored the decrease in Young's modulus and inhibited the formation of pseudopodia and F-actin. Overall, our study demonstrated that MGF-C25E promotes rat tenocyte migration by lessening cell stiffness and increasing pseudopodia formation via the FAK-ERK1/2 signaling pathway. - Highlights: • Mechano-growth factor E peptide (MGF-C25E) promotes migration of rat tenocytes. • MGF-C25E activates the FAK-ERK1/2 pathway in rat tenocytes. • MGF-C25E induces the actin remodeling and the formation of pseudopodia, and decreases the stiffness in rat tenocytes. • MGF-C25E promotes tenocyte migration via altering stiffness and forming pseudopodia by the activation of the FAK-ERK1/2 pathway.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1991

Properties of novel CVD graphite fibers and their bromine intercalation compounds

A hybrid fiber with a PAN core surrounded by a vapor grown carbon fiber (VGCF) sheath was fabricated using a proprietary process. The density, ultimate tensile strength, Young's modulus, and resistivity of pristine and bromine intercalated fibers made by this technique having diameters varying from 5 to 50 microns were compared with the values predicted from the rule of mixtures model. For both the pristine and intercalated fibers, the density, ultimate tensile strength, and Young's modulus of the fibers were lower than predicted, but the resistivity was measured to be consistent with predictions. The lower than theoretical mechanical properties may be evidence of a low density disordered interface between the core and the sheath which would lower the density and degrade the mechanical properties, but would leave the resistivity nearly unaffected. Intercalation had little if any effect on the ultimate tensile strength and Young's modulus, but raised the density by about 11 pct., and lowered the resistivity by an order of magnitude. The diameter dependence of the resistivity showed evidence of a depletion layer of the type found in VGCF.

Gaier, James R.↗
NASA NTRS1992

Properties of hybrid CVD/PAN graphite fibers and their bromine intercalation compounds

A hybrid fiber with a PAN core surrounded by a vapor grown carbon fiber (VGCF) sheath was fabricated using a proprietary process. The density, ultimate tensile strength, Young's modulus, and resistivity of pristine and bromine intercalated fibers made by this technique having diameters varying from 5 to 50 microns were compared with the values predicted from the rule of mixtures model. For both the pristine and intercalated fibers, the density, ultimate tensile strength, and Young's modulus of the fibers were lower than predicted, but the resistivity was measured to be consistent with predictions. The lower than theoretical mechanical properties may be evidence of a low density disordered interface between the core and the sheath which would lower the density and degrade the mechanical properties, but would leave the resistivity nearly unaffected. Intercalation had little if any effect on the ultimate tensile strength and Young's modulus, but raised the density by about 11 pct., and lowered the resistivity by an order of magnitude. The diameter dependence of the resistivity showed evidence of a depletion layer of the type found in VGCF.

Gaier, James R.↗
DOE OSTI2020

Macro- and micro-compression testing of shales

Here, macro- and micro-geomechanical properties of shales were investigated at millimeter- and micrometer-scale using an example of the Woodford Shale. Geomechanical properties, such as uniaxial (unconfined) compressive strength and Young's modulus, were quantified at the millimeter-scale and compared with results from micro-compression testing experiments of FIB-SEM-nanofabricated micro-pillars. Size-scale and compositional/structural heterogeneity effect on elasto-plastic deformation and failure behavior of shales were investigated. Also, relationship between elemental/mineral composition and unconfined compressive strength and Young's modulus, at a micrometer-scale, was discussed. It was shown that geomechanical properties of shales are scale-dependent and are strongly affected by compositional/structural anisotropy. In particular, micro-compression testing experiments showed non-uniformly distributed compressive strength and Young's modulus within the investigated Woodford Shale rock samples. It was demonstrated, that geomechanical properties of shales, investigated at the micrometer-scale, tend to be affected by different minerals and/or pores, while the same properties, investigated at the millimeter-scale, are governed by different micro-facies (and/or micro-fractures) present within the rock. This shows that geomechanical properties of shales can be dramatically different depending on the scale of investigation and compositional/structural heterogeneity of these rocks, and therefore are not easily transferable across the scales.

58 GEOSCIENCES↗
DOE OSTI2014

Nanoindentation and thermal characterization of poly (vinylidenefluoride)/MWCNT nanocomposites

We report the preparation, thermal and micro/nanomechanical behavior of poly (vinylidine diflouride) (PVDF)/multiwalled carbon nanotube (MWCNT) nanocomposites. It has been found that the addition of MWCNT considerably enhances the β-phase formation, thermal and mechanical properties of PVDF. Atomic force microscope (AFM) studies have been performed on the composites under stress conditions to measure the mechanical properties. The nanoscale mechanical properties of the composites like Young's modulus and hardness of the nanocomposites were investigated by nanoindentation technique. Morphological studies of the nanocomposites were also studied, observations show a uniform distribution of MWCNT in the matrix and interfacial adhesion between PVDF and MWCNT was achieved, which was responsible for enhancement in the hardness and Young's modulus. Differential scanning calorimetry (DSC) studies indicate that the melting temperature of the composites have been slightly increased while the heat of fusion markedly decreased with increasing MWCNT content.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Effect of Li level, artificial aging, and TiB2 reinforcement on the modulus of Weldalite (tm) 049

The dynamic Young's Modulus (E) was determined for (1) alloys 049(1.3)(heat 072), (2) 049(1.9), and (3) 049(1.3) TiB2 in the T3 temper and after aging at 160 C were made on a single 0.953 cm (0.375 in) cube to reduce scatter from microstructural inhomogeneities. Both shear and transverse wave velocities were measured for the L, LT, and ST directions by a pulse echo technique. These velocities were then used to calculate modulus. The change is shown in E with aging time at 160 C (320 F) for the three alloys. It is clear from the plots that aging has a minor, but measurable, influence on the E of alloys 049(1.3) and 049(1.9): E decreases by -2.5 pct. for 2 and 3 during the initial stages of artificial aging. This decrease in E generally follows the strength reversion. On further aging beyond the reversion well, E increases and then decreases again as the alloy overage. The slightly higher modulus in the T8 than in the T3 temper is consistent with the presence of the high modulus T sub 1 phase in the T8 temper. A similar change in E was observed on aging for the TiB2 reinforced variant that also follows the aging curve.

Source record↗
DOE OSTI2022

Predicting the Mechanical Response of Polyhydroxyalkanoate Biopolymers Using Molecular Dynamics Simulations

Polyhydroxyalkanoates (PHAs) have emerged as a promising class of biosynthesizable, biocompatible, and biodegradable polymers to replace petroleum-based plastics for addressing the global plastic pollution problem. Although PHAs offer a wide range of chemical diversity, the structure–property relationships in this class of polymers remain poorly established. In particular, the available experimental data on the mechanical properties is scarce. In this contribution, we have used molecular dynamics simulations employing a recently developed forcefield to predict chemical trends in mechanical properties of PHAs. Specifically, we make predictions for Young’s modulus, and yield stress for a wide range of PHAs that exhibit varying lengths of backbone and side chains as well as different side chain functional groups. Deformation simulations were performed at six different strain rates and six different temperatures to elucidate their influence on the mechanical properties. Our results indicate that Young’s modulus and yield stress decrease systematically with increase in the number of carbon atoms in the side chain as well as in the polymer backbone. In addition, we find that the mechanical properties were strongly correlated with the chemical nature of the functional group. The functional groups that enhance the interchain interactions lead to an enhancement in both the Young’s modulus and yield stress. Finally, we applied the developed methodology to study composition-dependence of the mechanical properties for a selected set of binary and ternary copolymers. Overall, our work not only provides insights into rational design rules for tailoring mechanical properties in PHAs, but also opens up avenues for future high throughput atomistic simulation studies geared towards identifying functional PHA polymer candidates for targeted applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

A Biomedical Ti-35Nb-5Ta-7Zr Alloy Fabricated by Powder Metallurgy

Ti-35Nb-5Ta-7Zr alloy for biomedical applications with a reduced Young’s modulus of less than 10 GPa, being comparable to that of human bones, was successfully fabricated by powder metallurgy method. The microstructure, compressive and tensile behavior were studied. Results indicate that Ti-rich and Ta-rich phases co-exist in β-matrix. Ti-35Nb-5Ta-7Zr alloys yield at about 10% in compression, with increasing in the content of process control agent, the resultant compressive yield strength and Young’s modulus increase from 650 ± 46 to 1055 ± 90 MPa and from 6.3 ± 0.03 to 8.24 ± 0.04 GPa, respectively. The tensile fractography of alloy with 9.7 GPa tensile Young’s modulus, 433 MPa UTS at the 5.5% elongation consists of cleavage fracture and ductile fracture with dimples. The failure mechanism has been discussed taking the intrinsic microstructural features into consideration.

36 MATERIALS SCIENCE↗
DOE OSTI2018

First-Principle Calculations on the Structural, Mechanical, and Electronic Properties of Mn{sub 2}RuSi and Mn{sub 2}RuGe Under Pressure

The second- and third-order elastic constants of the new Inverse Heusler compounds Mn{sub 2}RuZ (Z = Si, Ge) are determined from the first-principle calculations combined with homogeneous deformation methods. In terms of the second- and third- order elastic constants, the effective second-order elastic constants of Mn{sub 2}RuZ (Z = Si, Ge) are also presented. Besides, the pressure dependence of the brittle/ductile properties, elastic anisotropy factor, Young’s modulus, and Debye temperature is further investigated. It is found that both Mn{sub 2}RuSi and Mn{sub 2}RuGe display ductile nature at ground state and Mn{sub 2}RuGe has better ductility than Mn{sub 2}RuSi under different pressures. This phenomenon is improved by the Young’s modulus. Finally, the density of states of Mn{sub 2}RuZ (Z = Si, Ge) under different pressures is also calculated in order to reveal the origin of the effect of pressure on the the ductility of Mn{sub 2}RuZ (Z = Si, Ge).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Surpassing the stiffness-extensibility trade-off of elastomers via mastering the hydrogen-bonding clusters

The current paradigm of elastomer design typically falls into the trade-off between stiffness and extensibility. With a few reports on circumventing this trade-off behavior, e.g., increasing Young's modulus without sacrificing extensibility, the design principles to achieve improvements in both stiffness and extensibility have rarely been demonstrated. Herein, with a model system, i.e., cross-linked polydimethylsiloxane (PDMS) network, we demonstrate two approaches that can surpass the stiffness-extensibility trade-off and provide significant improvement in both parameters. Such an achievement is realized by introducing rationally arranged hydrogen-bonding units, i.e., ureidopyrimidone (UPy), leading to simultaneously improved Young's modulus and extensibility up to 158 and 3 times, respectively. Based on the experimental results, we also propose a microscopic picture of network rearrangement during the stretching process. Moreover, using this picture, we further improved Young's modulus of the elastic network without affecting its extensibility through mastering the distribution/topology of UPy clusters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1998

High Temperature Mechanical Characterization of Ceramic Matrix Composites

A high temperature mechanical characterization laboratory has been assembled at NASA Lewis Research Center. One contribution of this work is to test ceramic matrix composite specimens in tension in environmental extremes. Two high temperature tensile testing systems were assembled. The systems were assembled based on the performance and experience of other laboratories and meeting projected service conditions for the materials in question. The systems use frames with an electric actuator and a center screw. A PC based data acquisition and analysis system is used to collect and analyze the data. Mechanical extensometers are used to measure specimen strain. Thermocouples, placed near the specimen, are used to measure the specimen gage section temperature. The system for testing in air has a resistance element furnace with molybdenum disilicide elements and pneumatic grips with water cooling attached to hydraulic alignment devices. The system for testing in an inert gas has a graphite resistance element furnace in a chamber with rigidly mounted, water cooled, hydraulically actuated grips. Unidirectional SiC fiber reinforced reaction bonded Si3N4 and triaxially woven, two dimensional, SiC fiber reinforced enhanced SiC composites were tested in unidirectional tension. Theories for predicting the Young's modulus, modulus near the ultimate strength, first matrix cracking stress, and ultimate strength were applied and evaluated for suitability in predicting the mechanical behavior of SiC/RBSN and enhanced SiC/SiC composites. The SiC/RBSN composite exhibited pseudo tough behavior (increased area under the stress/strain curve) from 22 C to 1500 C. The rule of mixtures provides a good estimate of the Young's modulus of the SiC/RBSN composite using the constituent properties from room temperature to 1440 C for short term static tensile tests in air or nitrogen. The rule of mixtures significantly overestimates the secondary modulus near the ultimate strength. The ACK theory provides the best approximation of the first matrix cracking stress when residual stresses are ignored. The theory of Cao and Thouless, based on Weibull statistics, gave the best prediction for the composite ultimate strength. The enhanced SiC/SiC composite exhibited nonlinear stress/strain behavior from 24 C to 1370 C in air with increased ultimate strain when compared to monolithic SiC. The theory of Yang and Chou with the assumption of a frictional fiber/matrix interface provided the best estimate of the Young's modulus. The theory of Cao and Thouless gave the best estimate for the ultimate strength.

Gyekenyesi, John Z.↗
DOE OSTI2024

First-principles investigation of elastic, vibrational, and thermodynamic properties of kagome metals CsM 3 Te 5 (M = Ti, Zr, Hf)

Kagome metals are a unique class of quantum materials characterized by their distinct atomic lattice arrangement, featuring interlocking triangles and expansive hexagonal voids. These lattice structures impart exotic properties, including superconductivity, interaction-driven topological many-body phenomena, and magnetism, among others. The kagome metal CsM 3 ⁢Te 5 (where M = Ti, Zr, or Hf) exhibits both superconductivity and nontrivial topological electronic properties, offering a promising platform for exploring topological superconductivity. This study employs first-principles density functional theory calculations to systematically analyze the elastic, mechanical, vibrational, thermodynamic, and electronic properties of CsM 3 ⁢Te 5 (M = Ti, Zr, Hf). Our calculations reveal that the studied compounds—CsTi 3 ⁢Te 5 , CsZr 3 ⁢Te 5 , and CsHf 3 ⁢Te 5 —are ductile metals with elastic properties akin to the hexagonal Bi and Sb, with average elastic constants, including a bulk modulus of 27 GPa, a shear modulus of 11 GPa, and Young's modulus of 29 GPa. We observe peculiar dispersionless, flat, phonon branches in the vibrational spectra of these metals. Additionally, we thoroughly analyze the symmetries of the zone-center phonon eigenvectors and predict vibrational fingerprints of the Raman- and infrared-active phonon modes. The analysis of thermodynamic properties reveals the Einstein temperature for CsTi 3 ⁢Te 5 , CsZr 3 ⁢Te 5 , and CsHf 3 ⁢Te 5 to be 66, 54, and 53 K, respectively. Our orbital-decomposed electronic structure calculations reveal significant in-plane steric interactions and multiple Dirac band crossings near the Fermi level. We further investigate the role of spin-orbit coupling effect on the studied properties. Furthermore, this theoretical investigation sheds light on the intriguing quantum behavior of kagome metals.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Probing the Mechanical Performance of Micro-architected Porous Structures Through In Situ Characterization and Analysis

Micropores play critical roles in both natural and man-made materials. Such pores take on a variety of shapes and sizes ranging from spherical to irregular sphere-like voids with diameters spanning from the nanometer to millimeter scales. When porous structures are mechanically loaded, the pores direct the stress around their free surfaces, altering the material’s mechanical response relative to fully dense materials. In this study, for the first time, we create micro-architected porous samples using nanolithography and investigate the role of pore morphology by conducting a series of in situ micropillar compression tests in scanning electron microscopy. The findings demonstrate that porosity is the primary factor influencing the mechanical response of these micro-architected materials, as often seen on a macroscopic level. Additionally, we observed that pore geometry had a significant impact on Young’s modulus, yield stress, and strain energy density as a secondary parameter. Then, the extracted Young’s modulus was compared to macroscopic empirical models and determined the analytical models sufficiently described the impact of porosity in the microscopic scale but failed to capture the impact of second-order parameters. Furthermore, these results suggest how porous materials can be tailored to achieve desired mechanical properties based on the engineering applications of interest.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Towards ultra-stiff materials: Surface effects on nanoporous materials

The significant rise in the strength and stiffness of porous materials at nanoscale cannot be described by conventional scaling laws. This letter investigates the effective Young's modulus of such materials by taking into account surface effect in a microcellular architecture designed for an ultralight material whose stiffness is an order of magnitude higher than most porous materials. We find that by considering the surface effects the predicted stiffness using Euler-Bernoulli beam theory compares well to experimental data for spongelike nanoporous gold with random microstructures. Analytical results show that, of the two factors influencing the effective Young's modulus, the residual stress is more important than the surface stiffness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗