Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WIND TUNNELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

The steady-state flow quality in a model of a non-return wind tunnel

The structural cost of non-return wind tunnels is significantly less than that of the more conventional closed-circuit wind tunnels. However, because of the effects of external winds, the flow quality of non-return wind tunnels is an area of concern at the low test speeds required for V/STOL testing. The flow quality required at these low speeds is discussed and alternatives to the traditional manner of specifying the flow quality requirements in terms of dynamic pressure and angularity are suggested. The development of a non-return wind tunnel configuration which has good flow quality at low as well as at high test speeds is described.

Mort, K. W.↗
NASA NTRS2014

Static Aeroelastic Scaling and Analysis of a Sub-Scale Flexible Wing Wind Tunnel Model

This paper presents an approach to the development of a scaled wind tunnel model for static aeroelastic similarity with a full-scale wing model. The full-scale aircraft model is based on the NASA Generic Transport Model (GTM) with flexible wing structures referred to as the Elastically Shaped Aircraft Concept (ESAC). The baseline stiffness of the ESAC wing represents a conventionally stiff wing model. Static aeroelastic scaling is conducted on the stiff wing configuration to develop the wind tunnel model, but additional tailoring is also conducted such that the wind tunnel model achieves a 10% wing tip deflection at the wind tunnel test condition. An aeroelastic scaling procedure and analysis is conducted, and a sub-scale flexible wind tunnel model based on the full-scale's undeformed jig-shape is developed. Optimization of the flexible wind tunnel model's undeflected twist along the span, or pre-twist or wash-out, is then conducted for the design test condition. The resulting wind tunnel model is an aeroelastic model designed for the wind tunnel test condition.

Aeroelasticity↗
NASA NTRSDate not supplied

Inlet Performance of the NFAC 1/50th-scale 80- by 120- Foot Wind Tunnel

The National Full-Scale Aerodynamics Complex 80- by 120-Foot Wind Tunnel (80x120) was dedicated in 1987 and rated at 100 knots for full-scale aircraft testing at NASA Ames Research Center. The 80x120 is the world’s largest wind tunnel, designed as an open circuit tunnel with a large aerodynamically treated inlet open to the ambient atmospheric air. In 2017, damage was sustained within the wind tunnel drive system, opening a window to do testing using the existing 1/50th-scale model of the 80- by 120-Foot Wind Tunnel within the full-scale 80- by 120-Foot Wind tunnel test section. The objective of the research was to quantify the turbulence levels within the 1/50th-scale test section as a function of onset atmospheric wind direction (± 90 deg from tunnel center-line), variable test section speed (5 – 50 m/s) and purposeful obtrusion of wind flow into the inlet. The model wind tunnel inlet, contraction, and test section are geometrically identical to that of the full-scale wind tunnel and model testing provides aerodynamic performance characteristics under controlled test conditions allowing for insight into the full-scale test section flow quality. The test section turbulence levels are minimally affected by the onset direction of the ambient atmospheric wind, but are dramatically affected by the speed in the tunnel while operated in the presence of winds. Original design specifications were axial/vertical/lateral turbulence ≤ 0.5% at maximum test section speed, though early full scale tunnel testing determined that lateral turbulence would be ≤ 0.6%. For test section speeds ≥ 30 m/s the tunnel is within the design specification limits. Between 5 m/s and 30 m/s, the test section turbulence levels are dependent on the onset wind direction and test section speed where test section turbulence in the axial, vertical and lateral directions was seen to be between 0.5% and 1% and, at times, greater than 1%. Finally, testing was performed with blockage designs at the inlet to disrupt the wind flow quality entering the tunnel contraction zone in an attempt to create higher levels of turbulence for high turbulent test conditions simulating the earth’s boundary layer. The highest turbulence levels measured were 6% in the axial direction by use of large spires designed to obstruct ≈ 50% of the inlet area.

Inlet Performance↗
NASA NTRS1987

Cryogenic wind tunnels. I

The basic principles of cryogenic wind-tunnel operation are presented, and a typical cryogenic wind tunnel is described. Low-speed cryogenic wind tunnels are considered, along with some experiments conducted in these tunnels. Focus is placed on real-gas effects including condensation and thermal and caloric imperfections. The operating limits set by the saturation boundaries of nitrogen and air are analyzed, and the consequences of thermal and caloric imperfections on both isentropic and normal-shock flow in nitrogen are considered. The extension of analytical real-gas studies, including both laminar and turbulent boundary layers is covered. It is concluded that the deviation of the nitrogen boundary-layer parameters from their ideal-gas values are small, and that large real-gas effects will not be a factor in cryogenic tunnel simulation of the complex flows met in flight.

Kilgore, Robert A.↗
NASA NTRS1995

Anechoic wind tunnel study of turbulence effects on wind turbine broadband noise

This paper describes recent results obtained at MIT on the experimental and theoretical modelling of aerodynamic broadband noise generated by a downwind rotor horizontal axis wind turbine. The aerodynamic broadband noise generated by the wind turbine rotor is attributed to the interaction of ingested turbulence with the rotor blades. The turbulence was generated in the MIT anechoic wind tunnel facility with the aid of biplanar grids of various sizes. The spectra and the intensity of the aerodynamic broadband noise have been studied as a function of parameters which characterize the turbulence and of wind turbine performance parameters. Specifically, the longitudinal integral scale of turbulence, the size scale of turbulence, the number of turbine blades, and free stream velocity were varied. Simultaneous measurements of acoustic and turbulence signals were made. The sound pressure level was found to vary directly with the integral scale of the ingested turbulence but not with its intensity level. A theoretical model based on unsteady aerodynamics is proposed.

Loyd, B.↗
NASA NTRS1976

Effects of forward velocity on noise for a J85 turbojet engine with multitube suppressor from wind tunnel and flight tests

Flight and wind tunnel noise tests were conducted using a J85 turbojet engine as a part of comprehensive programs to obtain an understanding of forward velocity effects on jet exhaust noise. Nozzle configurations of primary interest were a 104-tube suppressor with and without an acoustically-treated shroud. The installed configuration of the engine was as similar as possible in the flight and wind tunnel tests. Exact simultaneous matching of engine speed, exhaust velocity, and exhaust temperature was not possible, and the wind tunnel maximum Mach number was approximately 0.27, while the flight Mach number was approximately 0.37. The nominal jet velocity range was 450 to 640 m/sec. For both experiments, background noise limited the jet velocity range for which significant data could be obtained. In the present tests the observed directivity and forward velocity effects for the suppressor are more similar to predicted trends for internally-generated noise than unsuppressed jet noise.

Stone, J. R.↗
NASA NTRS1988

Review of Aeronautical Wind Tunnel Facilities

The nation's aeronautical wind tunnel facilities constitute a valuable technological resource and make a significant contribution to the global supremacy of U.S. aircraft, both civil and military. At the request of NASA, the National Research Council's Aeronautics and Space Engineering Board organized a commitee to review the state of repair, adequacy, and future needs of major aeronautical wind tunnel facilities in meeting national goals. The comittee identified three main areas where actions are needed to sustain the capability of NASA's aeronautical wind tunnel facilities to support the national aeronautical research and development activities: tunnel maintenance and upgrading, productivity enhancement, and accommodation of new requirements (particularly in hypersonics). Each of these areas are addressed and the committee recommendations for appropriate actions presented.

Source record↗
NASA NTRS1973

C-5A/orbiter wind tunnel testing and analysis: Piggyback ferry

Wind tunnel testing and analytical studies of the feasibility of ferrying the NASA Shuttle Orbiter on the C-5A in a piggyback mode have been accomplished. Testing was conducted in the 8x12 foot low speed wind tunnel using an existing 0.0399 scale C-5A model in conjunction with a NASA 0.0405 scale Orbiter model. Six component force and moment data were measured over a range of pitch and yaw angles to determine lift and drag characteristics, lateral/directional stability characteristics and longitudinal and directional control powers. A description of the wind tunnel test program with a run schedule and the complete plotted data for all the test runs are presented. Initial emphasis was given to determining the effects of the Orbiter above the C-5A and the optimum location for minimum interference on C-5A characteristics. A comprehensive series of cruise configurations were tested including a range of Orbiter longitudinal and vertical locations, incidences, and afterbody fairings. Subsequently, a series of configurations were devised during the test program to determine means of recovering directional stability degradation due to Orbiter interference.

Tomlin, K. H.↗
NASA NTRS2006

Anomalous Shocks on the Measured Near-Field Pressure Signatures of Low-Boom Wind-Tunnel Models

Unexpected shocks on wind-tunnel-measured pressure signatures prompted questions about design methods, pressure signature measurement techniques, and the quality of measurements in the flow fields near lifting models. Some of these unexpected shocks were the result of component integration methods. Others were attributed to the three-dimension nature of the flow around a lifting model, to inaccuracies in the prediction of the area-ruled lift, or to wing-tip stall effects. This report discusses the low-boom model wind-tunnel data where these unexpected shocks were initially observed, the physics of the lifting wing/body model's flow field, the wind-tunnel data used to evaluate the applicability of methods for calculating equivalent areas due to lift, the performance of lift prediction codes, and tip stall effects so that the cause of these shocks could be determined.

Mack, Robert J.↗
NASA NTRS2018

Characterization of Freestream Disturbances in Conventional Hypersonic Wind Tunnels

While low disturbance ("quiet") hypersonic wind tunnels are believed to provide more reliable extrapolation of boundary layer transition behavior from ground to flight, the presently available quiet facilities are limited to Mach 6, moderate Reynolds numbers, low freestream enthalpy, and subscale models. As a result, only conventional ("noisy") wind tunnels can reproduce both Reynolds numbers and enthalpies of hypersonic flight configurations, and must therefore be used for flight vehicle test and evaluation involving high Mach number, high enthalpy, and larger models. This article outlines the recent progress and achievements in the characterization of tunnel noise that have resulted from the coordinated effort within the AVT-240 specialists group on hypersonic boundary layer transition prediction. New Direct Numerical Simulation (DNS) datasets elucidate the physics of noise generation inside the turbulent nozzle wall boundary layer, characterize the spatiotemporal structure of the freestream noise, and account for the propagation and transfer of the freestream disturbances to a pitot-mounted sensor. The new experimental measurements cover a range of conventional wind tunnels with different sizes and Mach numbers from 6 to 14 and extend the database of freestream fluctuations within the spectral range of boundary layer instability waves over commonly tested models. Prospects for applying the computational and measurement datasets for developing mechanism-based transition prediction models are discussed.

Duan, Lian↗
NASA NTRS2021

ED1: Design and Prototype of a 3D Printed Wind Tunnel Model with Integrated Force Measurement

Wind tunnel testing using conventionally manufactured force measurement systems (balances) is able to yield precise and accurate results. These balances are delicate, complex instruments. Due to the nature of this high-precision complexity, balances are expensive and time-consuming to produce. These factors can limit the design potential of the model because using conventionally manufactured balances generally means that the model is designed to accommodate balances that already exist. Ideally, engineers would be able to design a measurement system that is tailored to fit the needs of the model, rather than the other way around. The goal of this research project was to determine if it is possible to overcome these drawbacks by designing a wind tunnel model with a modifiable integrated force measurement system that leverages additive manufacturing. This was undertaken by utilizing the existing UT-63 wind tunnel balance (measurement system), integrating it with a model based on the existing AGARD-B model, and performing stress analysis to optimize the design. Due to time constraints, the result of this endeavor is currently incomplete. Continued analysis and optimization are required to have a thorough understanding of the success or failure of the attempted design. As additive manufacturing technology evolves, the ability for it to become the primary method of fabrication for sensitive measurement systems increases. This project contributes to this by providing one method for design, a framework for optimizing existing balances for additive manufacturing, and resources for performing necessary stress analysis.

Callie Ellsworth↗
NASA NTRS2013

Dry wind tunnel system

This invention is a ground flutter testing system without a wind tunnel, called Dry Wind Tunnel (DWT) System. The DWT system consists of a Ground Vibration Test (GVT) hardware system, a multiple input multiple output (MIMO) force controller software, and a real-time unsteady aerodynamic force generation software, that is developed from an aerodynamic reduced order model (ROM). The ground flutter test using the DWT System operates on a real structural model, therefore no scaled-down structural model, which is required by the conventional wind tunnel flutter test, is involved. Furthermore, the impact of the structural nonlinearities on the aeroelastic stability can be included automatically. Moreover, the aeroservoelastic characteristics of the aircraft can be easily measured by simply including the flight control system in-the-loop. In addition, the unsteady aerodynamics generated computationally is interference-free from the wind tunnel walls. Finally, the DWT System can be conveniently and inexpensively carried out as a post GVT test with the same hardware, only with some possible rearrangement of the shakers and the inclusion of additional sensors.

Chen, Ping-Chih↗
NASA NTRS2017

The Brothers Were Wright - An Abridged History of Wind Tunnel Testing at Ames Research Center

The Wright Brothers used wind tunnel data to refine their design for the first successful airplane back in 1903. Today, wind tunnels are still in use all over the world gathering data to improve the design of cars, trucks, airplanes, missiles and spacecraft. Ames Research Center is home to many wind tunnels, including the Unitary Plan Wind Tunnel complex. Built in the early 1950s, it is one of the premiere transonic and supersonic testing facilities in the country. Every manned spacecraft has been tested in the wind tunnels at Ames. This is a testing history from past to present.

Buchholz, Steve↗
NASA NTRS1973

The role of wind tunnel testing in the development of advanced rotary-wing aircraft

The relations of wind tunnel test objectives to wind tunnel test requirements are reviewed in an assessment of the current role of wind tunnel testing in the development of advanced rotary-wing aircraft. Elements of typical development programs are examined, and a comparison of fixed wing and rotary wing aircraft programs is presented. Proposed new test facilities for fixed wing aircraft and typical aircraft program costs are discussed, along with the use of wind tunnels for tilt rotor research aircraft and the role of 40 x 80 ft wind tunnels in tilt rotor aircraft development. Some changes in current programs and methods are outlined for bringing about desired improvements.

Kelly, M. W.↗
NASA NTRS1986

The optimum hypersonic wind tunnel

The capabilities of existing hypersonic wind tunnels in the U.S. are assessed to form a basis for recommendations for a new, costly facility which would provide data for modeling the hypervelocity aerodynamics envisioned for the new generation of aerospace vehicles now undergoing early studies. Attention is given to the regimes, both entry and aerodynamic, which the new vehicles will encounter, and the shortcomings of data generated for the Orbiter before flight are discussed. The features of foreign-gas, impulse, aeroballistic range, arc-heated and combustion-heated facilities are examined, noting that in any hypersonic wind tunnel the flow must be preheated to prevent liquefaction upon expansion in the test channel. The limitations of the existing facilities and the identification of the regimes which must be studied lead to a description of the characteristics of an optimum hypersonic wind tunnel, including the operations and productivity, the instrumentation, the nozzle design and the flow quality. Three different design approaches are described, each costing at least $100 million to achieve workability.

Trimmer, L. L.↗
NASA NTRS1997

Quiet Flow Characteristics of the NASA-Ames Laminar Flow Supersonic Wind Tunnel for Mach 1.6 Transition Studies

Low-disturbance or 'quiet' wind tunnels are an essential part of any meaningful boundary layer transition research. In particular, the receptivity of supersonic boundary layers to wind tunnel disturbances can significantly alter the transition phenomena under investigation on a test model. Consequently, considerable study has gone into the design of a new wind tunnel to provide quiet (low-disturbance) flow, encompassing both theoretical and experimental efforts. Our pilot (eighth-scale) supersonic wind tunnel was reported in 1992. NASA-Ames Fluid Mechanics Laboratory (FML) commissioned a quiet wind tunnel in 1994 to support Supersonic Laminar Flow Control (SLFC) research. Known as the Laminar Flow Supersonic Wind Tunnel (LFSWT), this tunnel is designed to operate at potential cruise Mach numbers and unit Reynolds numbers (Re) of the High Speed Civil Transport (HSCT). The need to better understand the transition phenomena on the leading edge region of swept (HSCT) wings provided the impetus for building the LFSWT. Additional information is contained in the original extended abstract.

Wolf, Stephen W. D.↗