Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UX”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Measurements in a Transitioning Cone Boundary Layer at Freestream Mach 3.5

An experimental study was conducted in the Supersonic Low-Disturbance Tunnel to investigate naturally-occurring instabilities in a supersonic boundary layer on a 7 deg half- angle cone. All tests were conducted with a nominal freestream Mach number of M(sub infinity) = 3:5, total temperature of T(sub 0) = 299:8 K, and unit Reynolds numbers of Re(sub infinity) x 10(exp -6) = 9:89, 13.85, 21.77, and 25.73 m(exp -1). Instability measurements were acquired under noisy- ow and quiet- ow conditions. Measurements were made to document the freestream and the boundary-layer edge environment, to document the cone baseline flow, and to establish the stability characteristics of the transitioning flow. Pitot pressure and hot-wire boundary- layer measurements were obtained using a model-integrated traverse system. All hot- wire results were single-point measurements and were acquired with a sensor calibrated to mass ux. For the noisy-flow conditions, excellent agreement for the growth rates and mode shapes was achieved between the measured results and linear stability theory (LST). The corresponding N factor at transition from LST is N 3:9. The stability measurements for the quiet-flow conditions were limited to the aft end of the cone. The most unstable first-mode instabilities as predicted by LST were successfully measured, but this unstable first mode was not the dominant instability measured in the boundary layer. Instead, the dominant instabilities were found to be the less-amplified, low-frequency disturbances predicted by linear stability theory, and these instabilities grew according to linear theory. These low-frequency unstable disturbances were initiated by freestream acoustic disturbances through a receptivity process that is believed to occur near the branch I locations of the cone. Under quiet-flow conditions, the boundary layer remained laminar up to the last measurement station for the largest Re1, implying a transition N factor of N greater than 8:5.

King, Rudolph A.↗

Application of Interval Predictor Models to Space Radiation Shielding

This paper develops techniques for predicting the uncertainty range of an output variable given input-output data. These models are called Interval Predictor Models (IPM) because they yield an interval valued function of the input. This paper develops IPMs having a radial basis structure. This structure enables the formal description of (i) the uncertainty in the models parameters, (ii) the predicted output interval, and (iii) the probability that a future observation would fall in such an interval. In contrast to other metamodeling techniques, this probabilistic certi cate of correctness does not require making any assumptions on the structure of the mechanism from which data are drawn. Optimization-based strategies for calculating IPMs having minimal spread while containing all the data are developed. Constraints for bounding the minimum interval spread over the continuum of inputs, regulating the IPMs variation/oscillation, and centering its spread about a target point, are used to prevent data over tting. Furthermore, we develop an approach for using expert opinion during extrapolation. This metamodeling technique is illustrated using a radiation shielding application for space exploration. In this application, we use IPMs to describe the error incurred in predicting the ux of particles resulting from the interaction between a high-energy incident beam and a target.

Crespo, Luis G.↗

Improving Photometric Calibration of Meteor Video Camera Systems

We present the results of new calibration tests performed by the NASA Meteoroid Environment Oce (MEO) designed to help quantify and minimize systematic uncertainties in meteor photometry from video camera observations. These systematic uncertainties can be categorized by two main sources: an imperfect understanding of the linearity correction for the MEO's Watec 902H2 Ultimate video cameras and uncertainties in meteor magnitudes arising from transformations between the Watec camera's Sony EX-View HAD bandpass and the bandpasses used to determine reference star magnitudes. To address the rst point, we have measured the linearity response of the MEO's standard meteor video cameras using two independent laboratory tests on eight cameras. Our empirically determined linearity correction is critical for performing accurate photometry at low camera intensity levels. With regards to the second point, we have calculated synthetic magnitudes in the EX bandpass for reference stars. These synthetic magnitudes enable direct calculations of the meteor's photometric ux within the camera band-pass without requiring any assumptions of its spectral energy distribution. Systematic uncertainties in the synthetic magnitudes of individual reference stars are estimated at 0:20 mag, and are limited by the available spectral information in the reference catalogs. These two improvements allow for zero-points accurate to 0:05 􀀀 0:10 mag in both ltered and un ltered camera observations with no evidence for lingering systematics.

Ehlert, Steven↗

Space Launch System Base Heating Test: Environments and Base Flow Physics

The NASA Space Launch System (SLS) vehicle is composed of four RS-25 liquid oxygen- hydrogen rocket engines in the core-stage and two 5-segment solid rocket boosters and as a result six hot supersonic plumes interact within the aft section of the vehicle during ight. Due to the complex nature of rocket plume-induced ows within the launch vehicle base during ascent and a new vehicle con guration, sub-scale wind tunnel testing is required to reduce SLS base convective environment uncertainty and design risk levels. This hot- re test program was conducted at the CUBRC Large Energy National Shock (LENS) II short-duration test facility to simulate ight from altitudes of 50 kft to 210 kft. The test program is a challenging and innovative e ort that has not been attempted in 40+ years for a NASA vehicle. This presentation discusses the various trends of base convective heat ux and pressure as a function of altitude at various locations within the core-stage and booster base regions of the two-percent SLS wind tunnel model. In-depth understanding of the base ow physics is presented using the test data, infrared high-speed imaging and theory. The normalized test design environments are compared to various NASA semi- empirical numerical models to determine exceedance and conservatism of the ight scaled test-derived base design environments. Brief discussion of thermal impact to the launch vehicle base components is also presented.

Mehta, Manish↗

Meteor Shower Forecasting for Spacecraft Operations

Although sporadic meteoroids are a much greater hazard to spacecraft than shower meteoroids in general, meteor showers can significantly increase the risk of damage over short time periods. Because showers are brief, it is sometimes possible to mitigate the risk operationally, which requires accurate predictions of shower activity. NASA's Meteoroid Environment Office generates an annual meteor shower forecast that describes the variations in the near-Earth meteoroid flux produced by meteor showers, which presents the shower flux both in absolute terms and relative to the sporadic ux. The shower forecast incorporates model predictions of annual variations in shower activity and quotes fluxes to several limiting particle kinetic energies. In this work, we describe our forecasting methods, compare them to actual observations, and highlight recent improvements to the temporal pro les based on flux measurements from the Canadian Meteor Orbit Radar (CMOR).

Moorhead, Althea V.↗

Compact LWIR Polarimeter for Cirrus Ice Properties

A miniaturized long-wave InfraRed (LWIR) spectro-polarimeter is being developed as a prototype for the Compact Submm-Wave and LWIR Polarimeters (SWIRP) project. The polarimeter in development is a compact (20x20x40 cm) conical-scan instrument to measure the polarimetric radiation from ice cloud scattering at mm-submm (220 and 680 GHz) and IR (8.6, 11, and 12 m) bands. The LWIR polarimeter will provide a series of polarization measurements across the 8.5 - 12.5 micron band, measuring the full set of linear Stokes parameters (I, Q, U) as a function of wavelength. The spectro-polarimeter uses a combination of birefringent crystals, a Wollaston prism, a diraction grating, and an uncooled microbolometer array to measure both the degree and angle of linear polarization across the spectral bandwidth by modulating the polarization ux in wavelength with a high order retarder.

LWIR↗

ALMA Spectral Imaging of Titan Contemporaneous with Cassini's Grand Finale

The Cassini mission performed 127 targeted ybys of Titan during its 13 yr mission to Saturn, culminating in the Grand Finale between 2017 April and September. Here we demonstrate the use of the Atacama Large Millimeter/ submillimeter Array (ALMA) to continue Cassini's legacy for chemical and climatological studies of Titan's atmosphere. Whole-hemisphere, interferometric spectral maps of HCN, HNC, HC3N, CH3CN, C2H3CN, C2H5CN,and C3H8 were obtained using ALMA in 2017 May at moderate (0 2, or 1300 km) spatial resolution, revealing the effects of seasonally variable chemistry and dynamics on the distribution of each species. The ALMA submillimeter observations of HCN and HC3N are consistent with Cassini infrared data on these species, obtained in the same month. Chemical/dynamical lifetimes of a few years are inferred for C2H3CN and C2H5CN, in reasonably close agreement with the latest chemical models incorporating the sticking of C2H5CN to stratospheric aerosol particles. ALMA radial limb ux proles provide column density information as a function of altitude, revealing maximum abundances in the thermosphere (above 600 km) for HCN, HNC, HC3N, and C2H5CN. This constitutes the rst detailed measurement of the spatial distribution of HNC, which is found to be conned predominantly to altitudes above 730 ± 60 km. The HNC emission map shows an east-west hemisphericasymmetry of 13% ± 3%. These results are consistent with very rapid production (and loss) of HNC in Titan's uppermost atmosphere, making this molecule an effective probe of short-timescale (diurnal) ionospheric processes.

Cordiner, M. A.↗

The Magnetosphere Ionosphere Electron Precipitation Dynamics and Their Geospace Consequences During the 17 March 2013 Storm

During geomagnetic storms and substorms, the magnetosphere and ionosphere are strongly coupled by precipitating magnetospheric electrons from the Earth's plasma sheet and driven by both magnetospheric and ionospheric processes. Magnetospheric wave activity initiates electron precipitation, and the ionosphere and upper atmosphere further facilitate this process by enhancing the value of precipitated energy uxes via connection of two magnetically conjugate regions and multiple atmospheric reections. This paper focuses on the resulting electron energy uxes and afliated heightintegrated Pedersen and Hall conductances in the auroral regions produced by multiple atmospheric reections during the 17 March 2013 geomagnetic storm and their effects on the inner magnetospheric electric eld and ring current. Our study is based on the magnetically and electrically selfconsistent Rice ConvectionModelEquilibrium of the inner magnetosphere with SuperThermal Electron Transport modied electron energy uxes that take into account the electron energy interplay between the two magnetically conjugate ionospheres. SuperThermal Electron Transportmodied energy ux in the Rice ConvectionModelEquilibrium leads to a signicant difference in the global conductance pattern, ionospheric electric eld formation, Birkeland current structure, ring current energization and its energy content, subauroral polarization drifts intensications and their spatial locations, interchange instability redistribution, and overall energy interplay on the global scale.

Khazanov, George V.↗

X-HAB 2020: AR Field Treks Summary and Conclusions

As part of the FY20 X-Hab Challenge, BLiSS sought to create an Augmented Reality (AR) toolkit to help with analog field trek operations under the supervision of the Solar System Exploration Research Virtual Institute (SSERVI). These treks are operational and technical demonstrations at space-like destinations on Earth to test current extra-vehicular activity (EVA) techniques. While BLiSS as an organization has experience studying operational tasks such as this, it has never developed AR software at this scale. For that reason, another team at the University was brought on to work in parallel. The Collaborative Lab for Advancing Work in Space (CLAWS) is a veteran group of the NASA Spacesuit User Interface Technologies for Students (SUITS) challenge in which Hololens displays for astronauts are created within a year. The operational and technological pairing was ideally suited for tackling this problem. The team divided its responsibilities so that BLiSS would handle the research required to shape the project. As this deliverable had an end user, it was decided that interviewing these field geologists and operations specialists would provide the best insight. These interviews paired with literature review would reveal niche applications for AR that remained within feasible bounds. These science-driven EVAs in unknown terrain require more flexible tools than the current generation of EVA assistants. Rather than focus on sequential instructions, there instead needs to be a broad toolkit that's only called upon in specific instances. This AR Toolkit for Lunar Astronauts and Scientists (ATLAS) became the development goal of the project: create a non-intrusive assembly of tools that could be accessed in AR on the field. The current ATLAS design makes use of a geospatially and temporally annotated eld note system called GeoNotes. This allows for data to be collected and coordinated in a way that's synchronized across time, space, and different users. A Mission Control Center (MCC) and Mobile Support Equipment (MSE) were all needed to transport the AR headset into the field with the user. A network infrastructure was designed and set up within the University to enable this functionality. The software is based on a Protocol-Module structure that allows for modular development of each capability. A Protocol Manager coordinates different protocols that make use of modules. Each module tackles a different individual task while the protocol puts each one to use. The protocol manager coordinates when these are called to be used. This software is hosted on a head-mounted display (HMD) with the MCC acting as support from afar. While the software would be unit-tested at each level and each hardware component verified, a final demonstration would serve to prove the system's capabilities: an analog field trek. The team would prepare to support a user in a remote location from the MCC back at the University. A local area near campus would be tested before going out to do sample field geology further away. This unfortunately became impossible with the arrival of COVID-19. Access to all of the facilities to complete the project as planned were shut down. Our team was scattered across the globe and forced to complete the rest virtually. Adjustments were made to produce a small virtual concept in Adobe XD in the meantime. Even digital surveys were created based on the NASA task-load index (TLX) originally intended for testing actual users. The goal shifted towards completing software and getting feedback on the user interfaces (UI) and user experiences (UX). This team has reformed in response to COVID and its focus has shifted to what can be done remotely. There is still an intention to finish the original deliverable described in this report. The work has been expanded beyond the original X-Hab challenge and has instead become its own research e ort to be continued afterwards. This report collects the processes and knowledge gained from a year of studying and working at this problem with two teams. It should preserve it for the time until the world returns to normal and work can resume. CLAWS will be taking over full responsibility from that point forward, eventually surpassing the original needs of the project. While this document captures the work done towards an eventual end, the CLAWS team has written their own proposal alongside it. It outlines a new future for ATLAS beyond X-Hab, BLiSS, and hopefully beyond COVID-19. This project began as a vague goal hoping to place a new technology into the unique setting of exploration science. The project has since comfortably taken root and will hopefully bloom over the next year.

Alex Sena↗

Vertiport Automation Software Architecture and Requirements

The purpose of Vertiport Automation Software Architecture and Requirements was developed to mature the Vertiport Automation System (VAS) described in the High-Density Automated Vertiport ConOps, into a set of artifacts that enable the development of a VAS prototype. The scope of document was to develop: (1) A VAS Software Architecture diagram that logically organizes VAS functionality into specific software components; (2) VAS Software Trade Study identifying existing commercial products and NASA research that can be used in part or with modifications to fulfill VAS functionality. (3) A set of VAS Functional Requirements which decompose the VAS concept into software functionality, including any interfaces and data flows needed; (4) A set of VAS Test Approaches describing a methodology for verification of the VAS Functional Requirements; and (5) An application user experience (UX) design study describing the general features needed in a VAS user interface.

Advanced Air Mobility↗

Upper Class E Traffic Management (ETM) NASA R&D Update

This slide set has been prepared for the 2022 Federal UxS Workshop to be held at NASA Ames Research Center. The presentation is designed to present the Upper Class E Traffic Management concept and work structure that it falls under and provide the audience with an update on recent progress, ongoing work, and future plans for research and testing.

Upper E↗

Integrating Human System Information with the Systems Platform for Aggregating and Relating Capabilities (SPARC)

Within Human Health and Performance, there exists a wealth of human system information that’s used a regular basis in support of NASA human exploration objectives, but the challenge is that all of this information was stored in multiple different locations and organized for specific uses, limiting its effectiveness and straining communication across multiple groups. To address this challenge, our project, the Systems Platform for Aggregating and Relating Capabilities (SPARC) was tasked with developing a new NASA internal web application that aggregates and relates multiple programs’ human system products, such as technical standards, program requirements and verifications, human system risks, research and evidence, and exploration capabilities, into one centralized platform that addresses the needs of human health and performance from multiple different perspectives. Using agile development methodologies, user-experience (UX) driven design principles, data visualization, and a strong emphasis on continuous improvement though consistent stakeholder engagement, the SPARC project released a beta version in less than 4 months, broadly launched version 1.0.0 Agency-wide three months after the beta, and has over 180 users in the first year of development. Our second year of development will see us moving from our initial capabilities to increasingly robust and complex integrations and visualizations, including Directed Acyclical Graphs (DAGs), natural language processing (NLP) for dynamic generation of relationships between the sources of truth, and an expansion into hierarchical levels of system design in support of the human exploration programs.

Data science↗

Solar-Energetic-Particle Track-Production Rates at 1 au: Comparing In-Situ Particle Fluxes with Lunar Sample-Derived Track Densities

Heavy ( Z > 26) solar energetic particles (SEPs) with energies ~1 MeV/nucleon are known to leave visible damage tracks in meteoritic materials. The density of such `solar flare tracks' in lunar and asteroidal samples has been used as a measure of a sample's exposure time to space, yielding critical information on planetary space weathering rates, the dynamics and lifetimes of interplanetary dust grains, and the long-term history of solar particle fluxes. Knowledge of the SEP track accumulation rate in planetary materials at 1 au is critical for properly interpreting observed track densities. Here, we use in-situ particle observations of the 0.50-3.0 MeV/nuc Fe-group SEP ux taken by NASA's Advanced Composition Explorer (ACE) to calculate a flux of track-inducing particles at 1 au of 6.0 × 10 5 cm -2 yr -1 str -1 . Using the observed energy spectrum of Fe-group SEPs, we find that the depth distribution of SEP-induced damage tracks inferred from ACE measurements matches closely to that recently measured in lunar sample 64455; however, the magnitude of the ACE-inferred rate is approximately 25× higher than that observed in the lunar sample. We discuss several hypotheses for the nature of this discrepancy, including inefficiencies in track formation, thermal annealing of lunar samples, erosion via space weathering processing, and variations in the SEP flux at the Moon, yet find no satisfactory explanation. We encourage further research on both the nature of SEP track formation in meteoritic materials and the flux of Fe-group SEPs at the lunar surface in recent and geologic times to resolve this discrepancy.

Interplanetary dust↗

Developing Concepts of Operations Using Multi-Step Tool Techniques With Large Language Models

The National Aeronautics and Space Administration (NASA) Air Mobility Pathfinders (AMP) project is developing and evaluating concepts of operations (ConOps) for safe, secure, and scalable Urban Air Mobility (UAM) operations. The AMP project’s Operational Concepts, Architecture, and Requirements Integration (OCARI) Team is using a Model Based System Engineering (MBSE) approach for integration, interoperability, and traceability of Advanced Air Mobility (AAM) ecosystems centered around urban air taxi services. The team’s goal is to define structures and behaviors needed for system feasibility, readiness, and interoperability, establish a UAM knowledge base, and trace and validate assumptions and requirements relevant to AAM. NASA Langley Research Center (LaRC) is spearheading an innovative digital engineering approach to integrate, communicate, and facilitate the research of multi-modal transportation systems. The Knowledge-based Digital Platform (KbDP) is a concept being developed that ties the workflows of Project Managers (PM), Principal Investigators (PI), and System Engineers together across organizational boundaries. It does so through the management of an information database defined by mathematical, data science, and system engineering principles. Machine Learning (ML) algorithms play a key role in this concept by extracting meaningful knowledge from relational and graph databases, document repositories, and system artifacts, which the human user leverages to greatly improve the efficiency and effectiveness of their research. Recent advancements in the field of Large Language Models (LLMs), specifically models trained for tool use, such as Command-R , now allow for the reliable implementation of single-step and multi-step tool-centric systems. These techniques provide the LLM with a set of tools, in our case Python functions, that can be called on to answer a much wider range of questions compared to LLMs implemented using a traditional single-source or Retrieval Augmented Generation (RAG) approach. Through this method, the LLM can pull information from multiple data sources, such as relational or graph databases, document repositories, application programming interfaces (APIs), and SysML artifacts depending on the user’s question. The LLM can also output the information in a variety of different formats, using output generation tools, such as CSV, UML, or SysML artifacts. Additionally, tools can be assigned roles and can work together to provide answers to queries in an “agent” like approach, similar to that implemented by Microsoft’s AutoGen framework where different agents can converse with each other to accomplish tasks. Previously, our team developed a chatbot system with “agent like” functionality in the form of different “modes” the user could select from a user interface (UI), this architecture can be seen on the left in figure 1. Three different modes were implemented, the first mode allowed the LLM to utilize the structures and algorithms within a graph database to trace UAM requirements. The second mode gave the LLM access to a vector search capable of providing relevant information from thousands of document pages related to UAM ConOps and requirements. The third mode served as a general assistant where users could enter open-ended questions and custom prompts to utilize the LLM for different use-cases. This system improved the process surrounding generating and analyzing information related to UAM requirements, however, the implementation provided a clunky user experience. Users were required to know what mode to select within the UI in advance before entering their question to the selected tool. Moreover, the different tools were isolated from each other, they lacked bidirectional links that would allow for tools to collaborate to generate better responses. Our team is working on a new architecture, seen on the right in the below figure, with the goal to address many of the UX shortcomings of our original system while improving the accuracy and depth of responses from the LLM. This new system will automatically select the appropriate tool to use based off the user’s question. Each tool will be capable of calling on any of the other tools available to the LLM, resulting in a collaborative pipeline where tools can pass data between other tools until enough data is received to generate an answer to the user’s question. Using a locally deployed, open-source, LLM, the NASA OCARI team, in collaboration with Collins Aerospace, will implement a prototype application that will bridge knowledge across multiple sources to assist System Engineers (SEs) with requirements discovery and tracing, research question and use case identification, and assumption validation. Such a system will also allow SEs to more easily, and intuitively, explore the AAM ecosystem, ultimately improving the efficiency and effectiveness of the SE's research and decision-making processes surrounding ConOps development and validation. In this session, our team will provide a video demonstration of our new prototype architecture in action. We will also present an overview of our prototype system architecture and talk about its advantages over traditional LLM deployments along with how those advantages can provide additional value to the field of System Engineering.

systems engineering↗

Indirect Dark Matter Detection Limits from the Ultra-Faint Milky Way Satellite Segue 1

We use new kinematic data from the ultra-faint Milky Way satellite Segue 1 to model its dark matter distribution and derive upper limits on the dark matter annihilation cross-section. Using gamma-ray ux upper limits from the Fermi satellite and MAGIC, we determine cross-section exclusion regions for dark matter annihilation into a variety of different particles including charged leptons. We show that these exclusion regions are beginning to probe the regions of interest for a dark matter interpretation of the electron and positron uxes from PAMELA, Fermi, and HESS, and that future observations of Segue 1 have strong prospects for testing such an interpretation. We additionally discuss prospects for detecting annihilation with neutrinos using the IceCube detector, finding that in an optimistic scenario a few neutrino events may be detected. Finally we use the kinematic data to model the Segue 1 dark matter velocity dispersion and constrain Sommerfeld enhanced models.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

SOLID SOLUTION EFFECTS ON THE THERMAL PROPERTIES IN THE MgAl2O4-MgGa2O4

Solid solution eects on thermal conductivity within the MgO-Al2O3-Ga2O3 system were studied. Samples with systematically varied additions of MgGa2O4 to MgAl2O4 were prepared and the laser ash technique was used to determine thermal diusivity at temperatures between 200C and 1300C. Heat capacity as a function of temperature from room temperature to 800C was also determined using dierential scanning calorimetry. Solid solution in the MgAl2O4-MgGa2O4 system decreases the thermal conductivity up to 1000C. At 200C thermal conductivity decreased 24% with a 5 mol% addition of MgGa2O4 to the system. At 1000C the thermal conductivity decreased 13% with a 5 mol% addition. Steady state calculations showed a 12.5% decrease in heat ux with 5 mol% MgGa2O4 considered across a 12 inch thickness.

Spinel↗

Electrostatic gyrokinetic simulation of global tokamak boundary plasma and the generation of nonlinear intermittent turbulence

Boundary plasma physics plays an important role in tokamak confinement, but is difficult to simulate in a gyrokinetic code due to the scale-inseparable nonlocal multi-physics in magnetic separatrix and open magnetic field geometry. Neutral particles are also an important part of the boundary plasma physics. In the present paper, novel electrostatic gyrokinetic techniques to simulate the ux-driven, low-beta electrostatic boundary plasma is reported. Gyrokinetic ions and drift-kinetic electrons are utilized without scale-separation between the neoclassical and turbulence dynamics. It is found that the nonlinear intermittent turbulence is a natural gyrokinetic phenomenon in the boundary plasma in the vicinity of the magnetic separatrix surface and in the scrape-off layer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Beam Dump eXperiment

Hadronic matter makes about 14% of the known universe. The remaining 86% is Dark Matter (DM). Since it does not interact with the ordinary matter via electromagnetic force, DM is not visible and, to date, it escaped detection. The search for Dark Matter (DM) is one of the hottest topic in modern physics. Despite the increasing number of astrophysical and cosmological observations proving the existence, so far no particle physics experiment has detected DM yet. Up to now, most of the experimental efforts have been focused on the so called WIMP (Weakly Interacting Massive Particle) paradigm, which predicts heavy DM (10 GeV-10 TeV mass range) interacting with Standard Model (SM) particles via the weak force mediators (W or Z bosons). More recently, due to the lack of clear evidence of WIMPs, other models of DM gained the interest of the physics community. These models consider Light DM particles (LDM), in MeV-GeV mass range. Among LDM theories, the Dark Photon theory predicts the existence of a Dark Sector interacting with SM particles via a new massive vector boson (Dark Photon, Heavy Photon or A0), mediator of a new force. This scenario, despite being theoretically well motivated, is remarkably experimentally unexplored. The Beam Dump eXperiment (BDX), is an approved experiment at Jefferson Lab (JLab), aiming to discover the DM predicted witihn the Dark Photon theory. The experiment uses the CEBAF (Continuous Electron Beam Accelerator Facility) 11 GeV electron beam, impinging on the JLab Hall-A beam-dump, to produce a beam of DM particles, detected by a ~ 1 m3 detector made of thallium doped cesium iodide (CsI(Tl)) crystals located ~ 20 m downstream. In order to achieve excellent background rejection, the experimental setup includes active vetos and passive shielding surrounding CsI(Tl) crystals. Given the weakness of the DM-SM interaction, the scattering of a DM particle in the BDX detector is a rare event. Therefore, the characterization of the expected background is a critical aspect of the experiment. Both cosmogenic and penetrating SM particles produced by the beam interaction in the dump contribute to the background of the experiment. While the cosmogenic contribution can be measured during the experiment when the beam is off, beam-related background can only be estimated via Monte Carlo (MC) simulations. Therefore, a careful assessment of possible systematics introduced by the MC is needed. The beam-correlated background characterization was made by measuring the muon flux produced by the interaction of the CEBAF beam with Hall-A dump in a dedicated experimental campaign in spring 2018 [1]. The comparison to the ?ux predicted by MC allowed us to validate the BDX simulation framework. The reach of BDX, i.e. the region that the experiment can probe in the LDM theory parameter space, depends critically on the background rejection capability and signal detection effciency. For this reason, the detector setup was fine-tuned through a dedicated study. The response to LDM and background events was evaluated for different setups and selection cuts. As a result of this procedure, the configuration resulting in the best sensitivity was selected [2]. The reach calculation was performed taking into account the different LDM production mechanisms, including the contribution of secondary particles produced in the beam-dump. In particular, the effect of the secondary positrons annihilation was found to be extremely significant. In the majority of the sensitivity studies, this contribution is neglected, but recent results [3] [4] demonstrated that this process significantly enhances the sensitivity of lepton beam-dump experiments. Currently, the BDX collaboration is focused on the deployment and operation of a small detector, called BDX-MINI, built to perform a preliminary physics measurement searching for LDM at JLab. This test will pave the way to the realization of the full BDX experiment. The measurement is currently ongoing but results are expected by the end of this year. During my PhD I was involved in all aspects of the BDX experiment: design, simulation, prototyping and data analysis. The main results of my work are reported in this thesis. This manuscript is organized as follows: the first Chapter provides an introduction to the theory of LDM, with particular attention to the Dark Photon paradigm; the second Chapter illustrates the BDX experimental setup, the LDM production and detection mechanisms and the expected backgrounds; Chapter 3 and 4 describe, respectively, the BDX-HODO measurement, with a detailed description of the simulations, and the BDX experimental setup and analysis cuts optimization. Chapter 5 reports about BDXMINI detector characterization, calibration and sensitivity estimate. Finally, Chapter 6 describes in detail the calculation of the secondary positron annihilation contribution to the sensitivity of BDX and other electron-beam thick-target experiment.

Marsicano, Luca↗