SEARCH · Engineering Papers

Results for “Tip vortex”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Sound generated in a cascade by three-dimensional disturbances convected in a subsonic flow

Discrete tone sound generation in a subsonic fan subject to three-dimensional disturbances is investigated. The analytical model used treats the fan rotor and stator as linear cascades of thin airfoils in a rectangular duct subject to a three-dimensional gust for which a complete aerodynamic theory already exists. The sound pressure can then be cast as the sum of a finite number of discrete sound waves (modes) the magnitude of which depends on an unknown function satisfying a singular integral equation. Similarity rules are derived to reduce the problem to that of a two-dimensional gust. Three-dimensional effects on the cut-off condition, the sound pressure, and the acoustic power are first investigated for each mode. The theory is then applied to noise generated by typical rotor-wake-defect and rotor-tip-vortex disturbances interacting with a stator.

Atassi, H.↗

NASA NTRS1983

Predicting aerodynamic characteristics of vortical flows on three-dimensional configurations using a surface-singularity panel method

A general low-order surface-singularity panel method is used to predict the aerodynamic characteristics of a problem where a wing-tip vortex from one wing closely interacts with an aft mounted wing in a low Reynolds Number flow; i.e., 125,000. Nonlinear effects due to wake roll-up and the influence of the wings on the vortex path are included in the calculation by using a coupled iterative wake relaxation scheme. The interaction also affects the wing pressures and boundary layer characteristics: these effects are also considered using coupled integral boundary layer codes and preliminary calculations using free vortex sheet separation modelling are included. Calculated results are compared with water tunnel experimental data with generally remarkably good agreement.

Maskew, B.↗

NASA NTRS1984

Graduate engineering research participation in aeronautics

Graduate student engineering research in aeronautics at Old Dominion University is surveyed. Student participation was facilitated through a NASA sponsored university program which enabled the students to complete degrees. Research summaries are provided and plans for the termination of the grant program are outlined. Project topics include: Failure modes for mechanically fastened joints in composite materials; The dynamic stability of an earth orbiting satellite deploying hinged appendages; The analysis of the Losipescu shear test for composite materials; and the effect of boundary layer structure on wing tip vortex formation and decay.

Roberts, A. S., Jr.↗

NASA NTRS1985

Effect of a wing-tip mounted pusher turboprop on the aerodynamic characteristics of a semi-span wing

An exploratory investigation has been conducted at the NASA Langley Research Center to determine the installed performance of a wing tip-mounted pusher turboprop. Tests were conducted using a semispan model having an unswept, untapered wing with a air-driven motor located on the tip of the wing, with an SR-2 design high speed propeller installed on the rear shaft of the motor. All tests were conducted at a Mach number of 0.70, at angles of attack of approximately -2 to +4 deg, and at a Reynolds number of 3.82 million based on the wing chord of 13 inches. The data indicate that, as a result of locating the propeller behind the wing trailing edge, at the wingtip, in the cross flow of the tip vortex, it is possible to recover part of the vortex energy as an increase in propeller thrust and, therefore, a reduction in the lift-induced drag as well.

Patterson, J. C., Jr.↗

NASA NTRS1986

Lift augmentation via spanwise tip blowing - A numerical study

Numerical simulations of a low aspect ratio wing with and without a spanwise directed jet issuing from the wing tip have been performed. The results show that the tip vortex is displaced outward and upward by the blowing. This gives rise to a local lift augmentation mechanism, vortex lift caused by the vortex core being above the wing, and a global mechanism, the reduction of induced velocities due to greater apparent spin.

Childs, R. E.↗

NASA NTRS1985

A new approach to the free wake problem for hovering rotors

In the present approach to the hovering rotor free wake problem, an influence coefficient solution method is used to find that rotor wake solution which is steady in a reference frame that rotates with the blades; this scheme solves directly for the conditions of free wake equilibrium by a procedure that does not involve time-stepping and the associated use of numerical damping or special convergence methods. The solution method has been implemented in a hover wake computer program having a three-part wake model for the tip vortex. All three wake regions are represented by the new Basic Curved Vortex Elements. Sample hover calculations are presented for single blade and multiblade rotors.

Bliss, D. B.↗

NASA NTRS1986

Full-scale tilt-rotor hover performance

The hover performance of three full-scale rotors was measured at the Ames Outdoor Aerodynamic Research Facility. The rotors, all designed for tilt-rotor aircraft, were the original metal blades for the XV-15 Tilt Rotor Research Aircraft, a set of composite, advanced technology blades for the XV-15, and a 0.658-scale model of the proposed V-22A Osprey (JVX) rotor. The composite advanced technology blades for the XV-15 were tested with several alternate blade root and blade tip configurations. This paper presents the performance of these three rotors, shows the effects of tip Mach number and root and tip configuration changes on rotor performance, and presents data on rotor wake velocity distributions and tip vortex geometry. Measured rotor performance is compared with theoretical predictions, and the discrepancies are discussed.

Felker, F. F.↗

NASA NTRS1986

Wing loads induced by a propeller wake

A wing located in the wake of a propeller sustains unsteady loading. This loading can generate components of structureborne noise which are transmitted to the interior of the aircraft. The vibration of the wing can also contribute to reradiation of propeller noise. An analysis system for the evaluation of wing unsteady loads is presented. The propeller wake is modeled as a potential helical tip vortex and unsteady airfoil theory is used to determine the wing response. The result is the forcing function for determining the structureborne noise. The wing response is evaluated as a function of propeller thrust coefficient, advance ratio, and propeller installation geometry. The system capabilities are demonstrated by application to three significantly different aircraft.

Weir, D. S.↗

NASA NTRS1985

Broadband noise of propellers and rotors

Three categories of rotor noise (discrete frequency noise, impulsive noise, and broadband noise) are described and a study made of broadband noise is reported. Broadband noise has a continuous spectrum and is caused by disturbances which are not precisely repeated at each blade revolution but are basically due to some sort of turbulence-blade interactions. Source mechanisms include: inflow turbulence noise, boundary layer trailing edge noise, tip vortex noise, and several uncommon mechanisms. Broadband noise analyses are reviewed and calculations based on various analyses are compared to each other and to some available experimental data. Several satisfactory analyses are discussed and their limitations are delineated. Twenty-two references are cited.

George, A. R.↗

NASA NTRS1987

Analyzing Wakes From Hovering-Helicopter Rotor Blades

New method for analyzing free wake of hovering-helicopter rotor produces more reliable results and requires less computer time. Copes with wake instabilities, both physical and numerical, that afflict usual time-stepping analysis methods. Tip-vortex position, in coordinates moving with rotor blade, updated in relaxation procedure. Wake-airflow solution reached when updates converge to steady wake shape.

Bliss, D. B.↗

NASA NTRS1987

Noise reduction for model counterrotation propeller at cruise by reducing aft-propeller diameter

The forward propeller of a model counterrotation propeller was tested with its original aft propeller and with a reduced diameter aft propeller. Noise reductions with the reduced diameter aft propeller were measured at simulated cruise conditions. Reductions were as large as 7.5 dB for the aft-propeller passing tone and 15 dB in the harmonics at specific angles. The interaction tones, mostly the first, were reduced probably because the reduced-diameter aft-propeller blades no longer interacted with the forward propeller tip vortex. The total noise (sum of primary and interaction noise) at each harmonic was significantly reduced. The chief noise reduction at each harmonic came from reduced aft-propeller-alone noise, with the interaction tones contributing little to the totals at cruise. Total cruise noise reductions were as much as 3 dB at given angles for the blade passing tone and 10 dB for some of the harmonics. These reductions would measurably improve the fuselage interior noise levels and represent a definite cruise noise benefit from using a reduced diameter aft propeller.

Dittmar, James H.↗

NASA NTRS1986

Detailed near-wake flowfield surveys with comparison to an Euler method of an aspect ratio 4 rectangular wing

An experimental investigation of the flowfield in the near-wake of an aspect ratio 4 rectangular wing was conducted, providing a complete detailed set of data for use in the validation of computational methods. An angle of attack of 8 degrees and two Reynolds numbers 530,000 and 391,000 were investigated using pitot and six-hole probes. In addition, two types of flow visualization were employed. The data presented includes contours of total pressure, mean velocity, flow angularity, and vorticity distribution data at five chordwise stations of the near-wake ranging from 0.167 to 5.00 chord lengths aft of the trailing edge. The experimental results were compared to the predicted results of a 2-D Euler numerical method. The results predicted by an Euler method failed to accurately define the flowfield. Tangential velocities remained relatively constant over the range of X/C considered though increased in angle of attack and Reynolds number did bring about corresponding increases. Axial velocities also increased with angle of attack and Reynolds number but showed greater sensitivity to increases in X/C. Graphic displays and contours of the total pressure data indicate that roll-up of the wing tip vortex is essentially complete one and one half chords downstream of the trailing edge.

Klinge, M. D.↗

NASA NTRS1987

Evaluation of installed performance of a wing-tip-mounted pusher turboprop on a semispan wing

An exploratory investigation has been conducted at the Langley Research Center to determine the effect of a wing-tip-mounted pusher turboprop on the aerodynamic characteristics of a semispan wing. Tests were conducted on a semispan model with an upswept, untapered wing and an airdriven motor that powered an SR-2 high-speed propeller located on the tip of the wing as a pusher propeller. All tests were conducted at a Mach number of 0.70 over an angle-of-attack range from approximately -2 to 4 deg at a Reynolds number of 3.82 x 10 to the 6th based on the wing reference chord of 13 in. The data indicate that, as a result of locating the propeller behind the wing trailing edge at the wing tip in the crossflow of the wing-tip vortex, it is possible to improve propeller performance and simultaneously reduce the lift-induced drag.

Patterson, James C., Jr.↗

NASA NTRS1987

The effect of front-to-rear propeller spacing on the interaction noise of a model counterrotation propeller at cruise conditions

The effect of front-to-rear propeller spacing on the interaction noise of a counterrotation propeller model was measured at cruise conditions. The data taken at an axial Mach number of 0.80 behaved as expected: interaction noise was reduced with increased spacing. The data taken at M=0.76 and M=0.72 did not behave as expected. At some of the test conditions the noise was unchanged; others even showed noise increases with increased spacing. A possible explanation, involving the amount of downstream blade area impacted by the tip vortex, is presented.

Dittmar, James H.↗

NASA NTRS1986

Progress in tail rotor noise analysis

Helicopter tail rotor noise generated by interactions with the main rotor tip vortices and with the fuselage separation mean wake is investigated. The tail rotor blade-main rotor tip vortex interaction is modeled as an airfoil of infinite span cutting through a moving vortex. The present results are compared to the tail rotor loading and high speed thickness noise and are found to be significant. This noise mechanism is a function of the helicopter operating conditions and the location of the tail relative to the main rotor. Tail rotor self-generated noise due to turbulent vortex shedding from blunt trailing edges is also analyzed.

Chou, S.-T.↗

NASA NTRS1986

The development of advanced technology blades for tilt-rotor aircraft

The paper discusses the development and ground testing of blades for the XV-15 tilt-rotor demonstrator aircraft. This work was performed under contract NAS2-11250 with NASA Ames Research Center. These blades, known as the Advanced Technology Blades (ATB), replace the rectangular, steel blades which were part of the XV-15 original design. The materials used in the primary structure of the ATB are fiberglass and high strain graphite epoxy laminates. This facilitates the use of 43 deg of nonlinear twist, a nonuniform tapered planform and thin airfoils required for aerodynamic efficiency. Instrumentation life is extended by encapsulating gages and wiring in the composite structure. Tip shells and cuff fairings are removable to provide access to tip weights and retention hardware; they are also replaceable with alternate research configurations. Extensive laboratory testing has validated predicted strength characteristics. Hover testing has demonstrated performance significantly superior to that predicted by contemporary methodology. Key elements of the test rig used for rotor performance measurement were developed as an ancillary part of the present program. The performance testing included measurement of near- and far-field noise. Induced inflow velocity distributions were also determined and photographs of tip vortex condensation trails were taken. These are providing guidance for modifications to hover peformance codes.

Alexander, Harold R.↗

NASA NTRS1987

The uses and abuses of the acoustic analogy in helicopter rotor noise prediction

The generation of noise by helicopter rotor blades is considered theoretically, reviewing recent analyses based on the acoustic analogy (where the effect of fluid motion is replaced by fictitious sources in an undisturbed fluid). The fundamental principles of the acoustic approach are explained and illustrated with diagrams; the governing Ffowcs-Williams/Hawkings equations are written with a reformulated quadrupole term; and the directivity of noise produced (1) by regions with steep gradients (such as shock surfaces) and (2) by boundary-layer quadrupoles (tip-vortex and blade wakes) is shown to be the same as that of thickness noise. The need to include both (1) and (2) in acoustic-analogy computations is indicated.

Farassat, F.↗

NASA NTRS1989

Unsteady blade pressure measurements on a model counterrotation propeller

In an exploratory effort an advanced counterrotation propeller instrumented with blade-mounted pressure transducers was tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel at a simulated takeoff and landing speed of Mach 0.20. The propeller's aft diameter was reduced to investigate possible noise reductions resulting from reduced blade row interaction with the tip vortex. The propeller was tested at three blade row spacings at fixed blade setting angles, at the maximum blade row spacing at higher blade setting angles and at propeller axis angles attack to the flow up to + or - 16 deg. A limited number of unsteady blade surface pressure measurements were made on both rotors of the model counterrotation propeller. Emphasis was placed on determining the effects of rotor-rotor interactions on the blade surface pressures. A unique method of processing the pressure signals was developed that enables even weak interaction waveforms and spectra to be separated from the total signal. The interaction on the aft rotor was many times stronger than that on the forward rotor. The fundamental rotor interaction tone exhibited complicated behavior but generally increased with rotational speed and blade setting angle and decreased with rotor spacing. With the propeller axis at an angle to the flow, the phase response of the aft rotor appeared to be significantly affected by the presence of the forward rotor.

Heidelberg, Laurence J.↗