Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRISO Fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Fission Product Diffusion in Silicon Carbide: As Revealed by Computer Simulations and Experimental Measurements

The diffusion and release of fission products through silicon carbide in the tri-structural isotropic (TRISO) fuel particles remain unsolved for decades. The underlying mechanism is quite challenging to be determined. To help unveil the mysterious story, the current work applies molecular dynamics method to show the stability of silver, palladium, ruthenium and iodine as an interstitial and their atomic diffusion along coincident site lattice (CSL) boundary, especially ?3 grain boundary (GB). The major finding presents a much faster diffusion along GB than in bulk for all elements considered. The reasonably close estimate to experiments and simulations where available has confirmed the important role of grain boundary diffusion of Ag and Pd in SiC. However, the discrepancy addressed in Ag with measurements from fuel studies suggest a more complicated mechanism, which might be in correlation with high energy grain boundaries or the presence of crack. The subsequent characterization of Ru and I distribution in SiC-PyC-SiC diffusion couples, which have been ion irradiated at 900?C to 10 dpa and 20 dpa, has performed by secondary ion mass spectrometry (SIMS) analysis. The experiment measurements correlate well with the grain boundary diffusion by simulation, which provide further evidences that the grain boundary diffusion cannot be neglected once the fission products are accessible at the grain boundary.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Safeguards Considerations for Coated Particle Fuel Fabrication Facilities

This study aims to identify where existing fuel fabrication safeguards are limited in application to coated particle fuel fabrication facilities; perform a review of techniques that may be appropriate to address these limitations; and identify where further study is required. The purpose is to ensure the necessary technology and safeguards developments are established to facilitate safeguards-by-design for coated particle fuel fabrication facilities, analogous to the research and development (R&D) efforts in the advanced reactor space, including those requiring coated particle fuels and progress to higher technology readiness levels. Finally, this study will also help meet high priority objectives set forth by the IAEA in establishing safeguards R&D precedence and measurement/procedural standards at emerging fuel fabrication facilities. To achieve these objectives, the report is formatted to (1) distill relevant background information on fuel fabrication of oxide and coated particle fuels; (2) provide an overview of the fuel fabrication techniques for a reference oxide fuel fabrication facility and two selected TRISO fuel fabrication facilities; (3) develop facility models of safeguards approaches for the reference facility and the two TRISO facilities; and (4) identify any observed technology needs or gaps from this analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

AGR-5/6/7 CAPSULE 1 THERMAL MODEL WITH OFFSET GAS GAPS

Fuel compact temperatures are a crucial factor in assessing the irradiation performance of tristructural isotropic (TRISO) fuel particles. In the absence of direct measurement, fuel compact temperatures were calculated using a 3 D finite-element thermal model that was subject to simulation uncertainty. The most dominant factor in the uncertainty of calculated fuel temperatures is the gas gap uncertainty caused by the graphite holder nub-to-capsule clearance. This thermal model was revised to examine the most probable graphite offset position for Capsule 1 for four different days during the irradiation. In the analysis, the offset distance and azimuthal direction at both the top and bottom of the holder were varied. The best-fit offset was estimated based on the minimum root mean square error (RMSE) of the residuals (measured minus calculated thermocouple [TC] temperatures) for the operational TCs in Capsule 1. Near the end of the irradiation, when the graphite had shrunk and the gas gaps had grown, a peak temperature was found with maximum offset along the TC lines, with nickel introducing a potential mechanism for fuel particle failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Microstructural Characterization of AGR-2 TRISO-coated Particle Buffer, IPyC, and Buffer-IPyC Interfaces

Investigating the microstructural, mechanical, and chemical behaviors of Tristructural Isotropic (TRISO) fuel particles is vital for its qualification and use in advanced reactors. Central to the study of TRISO particles is understanding the silicon carbide (SiC) layer's ability to confine fission products, with failure mechanisms linked to chemical degradation following mechanical degradation of the buffer and IPyC layers. Research has been done to quantify the micro-tensile properties of the buffer, inner pyrolytic carbon (IPyC), and buffer-IPyC interlayer regions and their interactions within both irradiated and un-irradiated TRISO particles. Techniques such as atom probe tomography (APT) and transmission electron microscopy (TEM) have also been deployed to examine microstructural defects and fission product distribution in detail. The goal is to understand layer delamination, establish connections between microstructure and mechanical attributes, and inform computational predictions of fuel performance. This work may help refine predictive models of TRISO fuel behavior and facilitating its certification for use in advanced reactors.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRSDate not supplied

The Use of Immersion Rigs for High Temperature Hydrogen Exposure Testing within the Nuclear Thermal Rocket Element Environmental Simulator (NTREES): Thermal Soak Rig (TSR)

The Nuclear Thermal Rocket Element Environmental Simulator (NTREES) facility was purpose constructed to perform non-nuclear evaluations of nuclear thermal propulsion (NTP) system fuel materials and structures within prototypic thermochemical environments. This system has been utilized steadily in its ability to subject test specimens to thermochemical and thermohydraulic environments simulating that of an operating nuclear rocket engine. Fission heat is simulated by induction power and experiments are conducted within a ~1000 psi pressure vessel. Hydrogen is conventionally passed through the heated fuel surrogate test specimen while pressure, temperature, and gas species data are collected at various points along the experiment. In order to test fuel and material coupon samples, a class of test apparatus named “immersion rigs” are being developed and employed to more rapidly test these smaller and more technically challenging test specimen. One example of a promising potential fuel structure, Tristructural-isotropic (TRISO) particles, presents unique challenges for testing of this type. TRISO fuel micro-particles are spheroids typically on the order of 500 – 1000 μm in diameter, and exposing a batch sample to hot hydrogen requires purpose-built special test equipment. Thusly, an immersion rig was developed and successfully demonstrated to expose ~1 g of micro-particles to hydrogen gas at temperatures and pressures relevant to NTP systems for the purpose of fuel evaluation. The rig, comprised primarily of graphite and pure tungsten, houses in its core a batch of micro-particles between pucks of porous silicon carbide (SiC). This approach permits gas flow while simultaneously retaining the particles in place. Herein is a discussion of the design, analysis, fabrication, and testing of the NTREES Thermal Soak Rig (TSR).

Space Nuclear Propulsion↗
DOE OSTI2021

Summary of Thermocouple Performance in the Advanced Gas Reactor Experiment AGR-5/6/7 During Irradiation in the Advanced Test Reactor

The Advanced Gas Reactor -5/6/7 (AGR-5/6/7) experiment was the fourth and final experiment in the AGR experiment series and completed irradiation in July 2020. It serves as the formal fuel qualification test for the TRISO fuels under development by the US Department of Energy. This experiment was designed to irradiate fuel particles at temperatures ranging from 800°C ? 1500°C. The high end of the range created unique challenges for thermocouple-based temperature measurements. Commercially available high-temperature platinum-rhodium thermocouples (Types S, R, and B) and tungsten-rhenium thermocouples (Type C) suffer rapid decalibration due to transmutation of the thermoelements from neutron absorption. A special low neutron cross-section thermocouple system based on molybdenum/niobium thermoelements called High Temperature Irradiation Resistant thermocouple (HTIR-TC) has been under development at INL since circa 2004. Several examples of this thermocouple type were incorporated into regions of the test operating above 1200°C. For regions in the test operating in the 1000°C ? 1200°C range, high-performance versions of Type N thermocouples recently developed at Cambridge University were installed. Standard Type N thermocouples were used in regions of the test operating below 1000°C. A total of 54 thermocouples were incorporated into the test. A report of the performance of this large heterogenous set of thermocouples over the first third of the irradiation was previously provided (ANIMMA 2019). This follow-on paper discusses results from the balance of the experiment (Feb 2019 - July 2020). Special attention is focused on potential drift of thermocouples operating in the higher temperature regions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Summary of Thermocouple Performance in the Advanced Gas Reactor Experiment AGR-5/6/7 During Irradiation in the Advanced Test Reactor

This is a conference presentation ppt file. The following abstract is for the entire conference paper - which will later be the subject of a PRS artifact The Advanced Gas Reactor -5/6/7 (AGR-5/6/7) experiment was the fourth and final experiment in the AGR experiment series and completed irradiation in July 2020. It serves as the formal fuel qualification test for the TRISO fuels under development by the US Department of Energy. This experiment was designed to irradiate fuel particles at temperatures ranging from 800°C ? 1500°C. The high end of the range created unique challenges for thermocouple-based temperature measurements. Commercially available high-temperature platinum-rhodium thermocouples (Types S, R, and B) and tungsten-rhenium thermocouples (Type C) suffer rapid decalibration due to transmutation of the thermoelements from neutron absorption. A special low neutron cross-section thermocouple system based on molybdenum/niobium thermoelements called High Temperature Irradiation Resistant thermocouple (HTIR-TC) has been under development at INL since circa 2004. Several examples of this thermocouple type were incorporated into regions of the test operating above 1200°C. For regions in the test operating in the 1000°C ? 1200°C range, high-performance versions of Type N thermocouples recently developed at Cambridge University were installed. Standard Type N thermocouples were used in regions of the test operating below 1000°C. A total of 54 thermocouples were incorporated into the test. A report of the performance of this large heterogenous set of thermocouples over the first third of the irradiation was previously provided (ANIMMA 2019). This follow-on paper discusses results from the balance of the experiment (Feb 2019 - July 2020). Special attention is focused on potential drift of thermocouples operating in the higher temperature regions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Initial Observations from AGR 5/6/7 Capsule 1

The fourth and final irradiation experiment in the Advanced Reactor Technologies (ART) Advanced Gas Reactor (AGR) fuel development and qualification program is designated as AGR-5/6/7. Data collected from the fabrication, irradiation, and post-irradiation examination (PIE) of this tristructural isotropic (TRISO) fuel are intended to serve as the primary data set for the qualification of this fuel for use in high-temperature gas-cooled reactors (INL 2021, Collin 2018b). However, data collected from the three preceding irradiations (i.e., AGR-1, AGR-2, and AGR-3/4) may also be used to supplement data collected from AGR-5/6/7. All components of the AGR-5/6/7 fuel (i.e., UCO kernels, TRISO coatings, and fuel compacts) were produced on an engineering scale at BWXT (Lynchburg, Virginia USA) according to the fuel specification (Marshall 2017). This fuel was irradiated in the northeast flux trap (NEFT) at the Advanced Test Reactor (ATR) at Idaho national Laboratory (INL) from February 16, 2018 to July 22, 2020 (Pham et al. 2021). Measurements in the fission product monitoring system (FPMS) indicated unexpected and significant numbers of failures of TRISO particles in Capsule 1 near the end of the sixth irradiation cycle (ATR Cycle 166A). In the fourth cycle (ATR Cycle 164B) and beyond, the sweep gas flow became very low (presumably from degradation of the capsule gas outlet line via an unidentified mechanism), and the program deliberately isolated Capsule 1 from gas flow periodically. In later cycles, attempts to reestablish any kind of flow in Capsule 1 were unsuccessful. With little or no flow through Capsule 1, FPMS measurements and enumerations of failed particles in Capsule 1 were difficult or impossible as was the ability to control the helium/neon gas mixture used for temperature control. Gas flows and fission gas activity in the effluent gas from the other AGR-5/6/7 capsules were also impacted by the Capsule 1 gas flow issues and the large increase in fission gas released from the Capsule 1.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Simulation of a TRISO MiniFuel irradiation experiment with data-informed uncertainty quantification

An irradiation experiment using tristructural isotropic (TRISO) fuel particles and the miniature fuel (MiniFuel) irradiation vehicle was performed in Oak Ridge National Laboratory’s High Flux Isotope Reactor (HFIR) to support development of the Kairos Power fluoride salt–cooled, high-temperature reactor (KP-FHR). Here, this paper describes modeling predictions of temperatures and fuel burnup for the as-built experiment. An uncertainty quantification (UQ) analysis was performed to determine the effect of TRISO particle volume and position on the temperature predictions at various fuel heat generation rates (HGRs). This UQ study utilized fuel kernel position and volume measurements previously collected using X-ray computed tomography (XCT) techniques and Monte Carlo sampling methods to generate fuel compact cases that were then analyzed using a finite element thermal model. The UQ analysis indicated that uncertainty in calculated temperatures caused by varying TRISO particle arrangement is relatively small, even at high fuel HGR. Final predictions of particle temperatures throughout the irradiation are shown to be relevant to KP-FHR normal and off-normal operating conditions and to previous TRISO irradiation experiments. The combination of XCT with UQ analyses will inform post-irradiation examination (PIE) of the irradiated fuel compacts, and these analyses can be used to develop fuel performance models for coated particle fuel forms. Both PIE of separate-effects irradiation data and enhanced fuel performance modeling support accelerated qualification of TRISO fuels for a broad range of advanced reactor applications. The novel approach demonstrated here of measuring TRISO particle configurations with XCT methods and generating representative fuel compacts for finite element modeling and UQ analysis could be leveraged by the broader particle fuel community in the development of other TRISO fuel experiments in which these variables may have a significant impact on key outcomes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Flattening the Radial Temperature Profile across the Transformational Challenge Reactor Core

The Transformational Challenge Reactor (TCR) program is demonstrating an agile development approach to advanced nuclear reactor design, which has traditionally utilized a linear design process. In leveraging artificial intelligence, additive manufacturing, advanced materials, and cutting-edge modeling and simulation, the TCR program aims to minimize the high cost and lengthy deployment timelines now standard in the nuclear industry. Within a relatively short period of time, a robust and mature advanced gas-cooled reactor was iteratively designed under the TCR program, using these cutting-edge technologies. The TCR is a 3 MWt gas-cooled microreactor fueled with uranium nitride (UN) tristructural isotropic (TRISO) fuel particles. Though manufactured via traditional means, these UN TRISO particles are loaded into additively manufactured silicon carbide (SiC) cans [4]. Once loaded with TRISO particles, the SiC cans are densified using a chemical vapor infiltration process. The additively manufactured SiC enables significantly more freedom in the design of the fuel form than could ever be achieved using traditionally manufactured SiC. The helium coolant, pressurized to 5 MPa, enters the core at 300°C and nominally exits it at 500°C. Typically, the most thermally limiting components in any reactor design are the fuel assemblies in the core center. To provide a wide thermal margin in these central fuel assemblies, the flow may be biased toward the center of the core to more effectively cool these fuel assemblies with more power deposition and flatten the core’s radial temperature distribution. An analytical fluid model of the TCR core was developed to explore methods for biasing the flow away from the cooler outer fuel assemblies and towards the hotter inner ones. Higher-fidelity models developed in STAR-CCM+ 2020.3.1, a computational fluid dynamics code, were then utilized to verify the analytical model’s findings.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

FEA-aided investigation of the effective thermal conductivity in a medium with embedded spheres

For multiple applications in nuclear energy, the ability to accurately represent material behavior with a simplified model is important to facilitate practical engineering-scale simulations. Here, we focus on the homogenized thermal response of a medium containing spherical inclusions, similar to a fuel form (compact or pebble) containing (TRISO) particles. A review on effective thermal conductivity (ETC) modeling is performed considering a random distribution of mono-sized spherical inclusions in a continuous matrix, with a primary focus on the analytical models. Finite element simulations are performed to evaluate each analytical model in varying material conditions. The model predictions are compared with the expected results obtained from the finite element predictions in addition to the Wiener and Hashin-Shtrikman bounds. Lastly, we included a practical discussion on the homogenization applied to a TRISO fuel pebble.

42 ENGINEERING↗
DOE OSTI2023

Evaluation of the spatial self-shielding impact for TRISO-based nuclear fuel depletion

Reactor physics analyses of nuclear cores with nuclear fuel concepts containing tristructural isotropic (TRISO) particles, such as pebbles or compact fuel elements, rely on various degrees of simplification to keep these highly heterogeneous problems computationally tractable. One such limitation regards the level of spatial discretization employed during burnup calculations, where traditionally only a limited number of spatial zones are modeled at the full core level and assume that the spectrum is constant within the fuel elements and TRISO particles in this depletion zone. This type of assumption neglects the impact of spatial self-shielding effect within the kernels (microscale level) as well as within the compact or pebbles (mesoscale level). Furthermore, the Monte Carlo code Serpent 2 contains many relevant features for efficiently modeling this type of geometry, including a collision-based domain decomposition intended for very large burnup calculations, which we leveraged for this work to quantify the impact of capturing neutron flux variations occurring at the micro- and mesoscale level on a series of high-temperature gas-cooled reactor fuel element depletion problems. While spatial self-shielding is observed at both scales, with differences from a volume-averaged burnup of ±7% within the kernels and ±2% between TRISO particles within the fuel element, the conjugated effect on nuclide inventories and multiplication factor are negligible, hence confirming that assuming a single average spectrum value may be sufficient for most applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Status of U.S. DOE Deliverables 0 July 2023

An annual status of the US TRISO fuel qualification program is provided, with a focus on activities linked to the Generation IV International Forum (GIF) Very High Temperature Reactor (VHTR) Fuel and Fuel Cycle (FFC) Project Management Board (PMB).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

DoD Symposium Presentation

TRISO fuel, or TRi-structural ISOtropic, is a ceramic based nuclear fuel capable of operating at high temperatures (up to 1600°C). The fuel, consisting of uranium oxycarbide (UCO) fuel kernels, is coated with three layers of carbon and ceramic (dense silicon carbide) materials to capture and contain radioactive fission products. BWXT, located in Lynchburg, VA, has perfected the manufacturing techniques to produce this fuel and is currently the only US company licensed to produce this irradiation-tested fuel. BWXT is currently producing fuel in support of a demonstration reactor scheduled for startup on the INL site in 2025. The first fuel delivery, estimated at 200 kilograms High Assay Low Enriched Uranium, is targeted for the end of CY2024.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2025

A Machine Learning Approach Toward Improving QA/QC of Coated Particle Fuels

Coated particle fuels, such as the tristructural isotropic (TRISO) fuel particle, have been studied and developed for decades for high-temperature gas reactor (HTGR) applications because of their efficiency and relative stability under off-normal conditions. Critical to this development is a strong understanding of the relationship between fuel fabrication, properties and performance, as is how the former can be adjusted and improved to optimize the latter. Accordingly, wide-scale implementation of coated nuclear particle fuels requires thorough and robust quality assurance/quality control (QA/QC) methods for fabrication, characterization, and deployment

Conry, Bryan [ORNL] (ORCID:0000000236089604)↗
DOE OSTI2026

TRISO Spent Nuclear Fuel Recycling or Waste Reduction Using SRNL Vapor Digestion Technology – 25635

There is a renewed interest in advanced reactors, including high-temperature gas cooled reactors (HTGRs). Tri-structural isotropic (TRISO) fuel is being used in many HTGR designs, whether as SMRs or microreactors. However, TRISO-based HTGRs discharge the largest volume of used fuel per megawatt-hour of energy produced compared to other reactors. An order of magnitude reduction or more in the volume of SNF could be realized if the TRISO particles were separated from the graphite moderator and the carbon dispositioned as LLW. The Savannah River National Laboratory (SRNL) has a patented technology readiness level (TRL) 4/5 vapor digestion process for separating nuclear-grade graphite from HTGR SNF. The SRNL process is based on the reaction of NOx species with carbon to form CO2. Because NOx species are several orders of magnitude more reactive with graphite than oxygen, the process can operate at lower temperatures with uncrushed HTGR pebbles or prismatic blocks. Because the fuel elements do not need to be crushed and the graphite is digested using a vapor-based process, the potential for damaging the TRISO particles is much reduced. The DOE Office of Technology Transitions (OTT) is funding SRNL and the University of South Carolina at Columbia to close certain gaps that exist within the technology which impede its direct application to the processing of commercial TRISO-based SNF coming from HTGR advanced reactors.

Pierce, Robert [Savannah River National Laboratory↗